Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: The primary cause of Total Hip Replacement (THR)
failure for younger patients is aseptic loosening. This complication is
twice more likely to happen in acetabular cup than in femoral stem.
Excessive micromotion between bone and implant will cause
loosening and it depends in patient activities, age and bone. In this
project, the effects of different metal back design of press fit on
osseointegration of the acetabular cup are carried out. Commercial
acetabular cup designs, namely Spiked, Superfix and Quadrafix are
modelled and analyzed using commercial finite element software.
The diameter of acetabular cup is based on the diameter of acetabular
rim to make sure the component fit to the acetabular cavity. A new
design of acetabular cup are proposed and analyzed to get better
osseointegration between the bones and implant interface. Results
shows that the proposed acetabular cup designs are more stable
compared to other designs with respect to stress and displacement
aspects.
Abstract: The past decade has witnessed a good opportunities
for city development schemes in UK. The government encouraged
restoration of city centers to comprise mixed use developments with
high density residential apartments. Investments in regeneration areas
were doing well according to the analyses of Property Databank
(IPD). However, more recent analysis by IPD has shown that since
2007, property in regeneration areas has been more vulnerable to the
market downturn than other types of investment property. The early
stages of a property market downturn may be felt most in
regeneration where funding, investor confidence and occupier
demand would dissipate because the sector was considered more
marginal or risky when development costs rise. Moreover, the Bank
of England survey shows that lenders have sequentially tightened the
availability of credit for commercial real estate since mid-2007. A
sharp reduction in the willingness of banks to lend on commercial
property was recorded. The credit crunch has already affected
commercial property but its impact has been particularly severe in
certain kinds of properties where residential developments are
extremely difficult, in particular city centre apartments and buy-to-let
markets. Commercial property – retail, industrial leisure and mixed
use were also pressed, in Birmingham; tens of mixed use plots were
built to replace old factories in the heart of the city. The purpose of
these developments was to enable young professionals to work and
live in same place. Thousands of people lost their jobs during the
recession, moreover lending was more difficult and the future of
many developments is unknown. The recession casts its shadow upon
the society due to cuts in public spending by government, Inflation,
rising tuition fees and high rise in unemployment generated anger and
hatred was spreading among youth causing vandalism and riots in
many cities. Recent riots targeted many mixed used development in
the UK where banks, shops, restaurants and big stores were robbed
and set into fire leaving residents with horror and shock. This paper
examines the impact of the recession and riots on mixed use
development in UK.
Abstract: Algae-based fuel are considered a promising sources
of clean energy, and because it has many advantages over traditional
biofuel, research and business ventures have driven into developing
and producing Algal-biofuel. But its production stages create a cost
structure that it is not competitive with traditional fuels. Therefore,
cost becomes the main obstacle in commercial production purpose.
However, the present research which aims at using cost structure
model, and designed MS-Dose program, to investigate the a mount of
production cost and determined the parameter had great effect on it,
second to measured the amount of contribution rate of algae in
process the pollution by capturing Co2 from air . The result generated
from the model shows that the production cost of biomass is between
$0.137 /kg for 100 ha and $0.132 /kg for 500 ha which was less than
cost of other studies, while gallon costs between $3.4 - 3.5, more
than traditional sources of oil about $1 ,which regarded as a rate of
contribution of algal in capturing CO2 from air.
Abstract: To investigate the energy performance of solar shading devices, this paper carried out a survey on the current status of solar shading utilization in buildings in Ningbo and performed building simulations to evaluate the energy savings potential by adopting different solar shading devices. Results show that solar shading utilization in this area is not popular and effective, and should be considered firstly in the design stage since the potential for energy savings is up to 6.8% for residential buildings and 9.4% for commercial buildings.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: Xanthan gum is a microbial polysaccharide of great
commercial significance. The purpose of this study was to select the
optimum fermentation time for xanthan gum production by
Xanthomonas campestris (NRRL-B-1459) using 10% sugar beet
molasses as a carbon source. The pre-heating of sugar beet molasses
and the supplementation of the medium were investigated in order to
improve xanthan gum production. Maximum xanthan gum
production in fermentation media (9.02 g/l) was observed after 4 days
shaking incubation at 25°C and 240 rpm agitation speed. A solution
of 10% sucrose was used as a control medium. Results indicated that
the optimum period for xanthan gum production in this condition was
4 days.
Abstract: Rice, which is the staple food in Sierra Leone, is
consumed on a daily basis. It is the most imperative food crop
extensively grown by farmers across all ecologies in the country.
Though much attention is now given to rice grain production through
the small holder commercialization programme (SHCP), however, no
attention has been given in investigating the limitations faced by rice
producers. This paper will contribute to attempts to overcome the
development challenges caused by food insecurity. The objective of
this paper is thus, to analysis the relationship between rice production
and the domestic retail price of rice. The study employed a log linear
model in which, the quantity of rice produced is the dependent
variable, quantity of rice imported, price of imported rice and price of
domestic rice as explanatory variables. Findings showed that, locally
produced rice is even more expensive than the imported rice per ton,
and almost all the inhabitants in the capital city which hosts about
65% of the entire population of the country favor imported rice, as it
is free from stones with other impurities. On the other hand, to
control price and simultaneously increase rice production, the
government should purchase the rice from the farmers and then sell to private retailers.
Abstract: In this investigation, types of commercial and special
polyacrylonitrile (PAN) fibers contain sodium 2-methyl-2-
acrylamidopropane sulfonate (SAMPS) and itaconic acid (IA)
comonomers were studied by fourier transform infrared (FT-IR)
spectroscopy. The study of FT-IR spectra of PAN fibers samples
with different comonomers shows that during stabilization of PAN
fibers, the peaks related to C≡N bonds and CH2 are reduced sharply.
These reductions are related to cyclization of nitrile groups and
stabilization procedure. This reduction in PAN fibers contain IA
comonomer is very intense in comparison with PAN fibers contain
SAMPS comonomer. This fact indicates the cycling and stabilization
for sample contain IA comonomer have been conducted more
completely. Therefore the carbon fibers produced from this material
have higher tensile strength due to suitable stabilization.
Abstract: One of the most important aspects expected from ERP systems is to integrate various operations existing in administrative, financial, commercial, human resources, and production departments of the consumer organization. Also, it is often needed to integrate the new ERP system with the organization legacy systems when implementing the ERP package in the organization. Without relying on an appropriate software architecture to realize the required integration, ERP implementation processes become error prone and time consuming; in some cases, the ERP implementation may even encounters serious risks. In this paper, we propose a new architecture that is based on the agent oriented vision and supplies the integration expected from ERP systems using several independent but cooperator agents. Besides integration which is the main issue of this paper, the presented architecture will address some aspects of intelligence and learning capabilities existing in ERP systems
Abstract: Over 90% of the world trade is carried by the
international shipping industry. As most of the countries are
developing, seaborne trade continues to expand to bring benefits for
consumers across the world. Studies show that world trade will
increase 70-80% through shipping in the next 15-20 years. Present
global fleet of 70000 commercial ships consumes approximately 200
million tonnes of diesel fuel a year and it is expected that it will be
around 350 million tonnes a year by 2020. It will increase the
demand for fuel and also increase the concentration of CO2 in the
atmosphere. So, it-s essential to control this massive fuel
consumption and CO2 emission. The idea is to utilize a diesel-wind
hybrid system for ship propulsion. Use of wind energy by installing
modern wing-sails in ships can drastically reduce the consumption of
diesel fuel. A huge amount of wind energy is available in oceans.
Whenever wind is available the wing-sails would be deployed and
the diesel engine would be throttled down and still the same forward
speed would be maintained. Wind direction in a particular shipping
route is not same throughout; it changes depending upon the global
wind pattern which depends on the latitude. So, the wing-sail
orientation should be such that it optimizes the use of wind energy.
We have made a computer programme in which by feeding the data
regarding wind velocity, wind direction, ship-motion direction; we
can find out the best wing-sail position and fuel saving for
commercial ships. We have calculated net fuel saving in certain
international shipping routes, for instance, from Mumbai in India to
Durban in South Africa. Our estimates show that about 8.3% diesel
fuel can be saved by utilizing the wind. We are also developing an
experimental model of the ship employing airfoils (small scale wingsail)
and going to test it in National Wind Tunnel Facility in IIT
Kanpur in order to develop a control mechanism for a system of
airfoils.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: The financial crisis has decreased the opportunities of
small businesses to acquire financing through conventional financial
actors, such as commercial banks. This credit constraint is partly the
reason for the emergence of new alternatives of financing, in addition
to the spreading opportunities for communication and secure
financial transfer through Internet. One of the most interesting venues
for finance is termed “crowdfunding". As the term suggests
crowdfunding is an appeal to prospective customers and investors to
form a crowd that will finance projects that otherwise would find it
hard to generate support through the most common financial actors.
Crowdfunding is in this paper divided into different models; the
threshold model, the microfinance model, the micro loan model and
the equity model. All these models add to the financial possibilities of
emerging entrepreneurs.
Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: In this paper we propose a novel approach for
searching eCommerce products using a mobile phone, illustrated by a
prototype eCoMobile. This approach aims to globalize the mobile
search by integrating the concept of user multilinguism into it. To
show that, we particularly deal with English and Arabic languages.
Indeed the mobile user can formulate his query on a commercial
product in either language (English/Arabic). The description of his
information need on commercial products relies on the ontology that
represents the conceptualization of the product catalogue knowledge
domain defined in both English and Arabic languages. A query
expressed on a mobile device client defines the concept that
corresponds to the name of the product followed by a set of pairs
(property, value) specifying the characteristics of the product. Once a
query is submitted it is then communicated to the server side which
analyses it and in its turn performs an http request to an eCommerce
application server (like Amazon). This latter responds by returning
an XML file representing a set of elements where each element
defines an item of the searched product with its specific
characteristics. The XML file is analyzed on the server side and then
items are displayed on the mobile device client along with its
relevant characteristics in the chosen language.