Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: Reactiondiffusion systems are mathematical models that describe how the concentration of one or more substances distributed in space changes under the influence of local chemical reactions in which the substances are converted into each other, and diffusion which causes the substances to spread out in space. The classical representation of a reaction-diffusion system is given by semi-linear parabolic partial differential equations, whose general form is ÔêétX(x, t) = DΔX(x, t), where X(x, t) is the state vector, D is the matrix of the diffusion coefficients and Δ is the Laplace operator. If the solute move in an homogeneous system in thermal equilibrium, the diffusion coefficients are constants that do not depend on the local concentration of solvent and of solutes and on local temperature of the medium. In this paper a new stochastic reaction-diffusion model in which the diffusion coefficients are function of the local concentration, viscosity and frictional forces of solvent and solute is presented. Such a model provides a more realistic description of the molecular kinetics in non-homogenoeus and highly structured media as the intra- and inter-cellular spaces. The movement of a molecule A from a region i to a region j of the space is described as a first order reaction Ai k- → Aj , where the rate constant k depends on the diffusion coefficient. Representing the diffusional motion as a chemical reaction allows to assimilate a reaction-diffusion system to a pure reaction system and to simulate it with Gillespie-inspired stochastic simulation algorithms. The stochastic time evolution of the system is given by the occurrence of diffusion events and chemical reaction events. At each time step an event (reaction or diffusion) is selected from a probability distribution of waiting times determined by the specific speed of reaction and diffusion events. Redi is the software tool, developed to implement the model of reaction-diffusion kinetics and dynamics. It is a free software, that can be downloaded from http://www.cosbi.eu. To demonstrate the validity of the new reaction-diffusion model, the simulation results of the chaperone-assisted protein folding in cytoplasm obtained with Redi are reported. This case study is redrawing the attention of the scientific community due to current interests on protein aggregation as a potential cause for neurodegenerative diseases.
Abstract: Many people regard food events as part of gastronomic tourism and important in enhancing visitors’ experiences. Realizing the importance and contribution of food events to a country’s economy, the Malaysia government is undertaking greater efforts to promote such tourism activities to international tourists. Among other food events, the Ramadan bazaar is a unique food culture event, which receives significant attention from the Malaysia Ministry of Tourism. This study reports the empirical investigation into the international tourists’ perceptions, attraction towards the Ramadan bazaar and willingness in disseminating the information. Using the Ramadan bazaar at Kampung Baru, Kuala Lumpur as the data collection setting, results revealed that the Ramadan bazaar attributes (food and beverages, events and culture) significantly influenced the international tourist attraction to such a bazaar. Their high level of experience and satisfaction positively influenced their willingness to disseminate information. The positive response among the international tourists indicates that the Ramadan bazaar as gastronomic tourism can be used in addition to other tourism products as a catalyst to generate and boost the local economy. The related authorities that are closely associated with the tourism industry therefore should not ignore this indicator but continue to take proactive action in promoting the gastronomic event as one of the major tourist attractions.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: Recently, a lot of attention has been devoted to
advanced techniques of system modeling. PNN(polynomial neural
network) is a GMDH-type algorithm (Group Method of Data
Handling) which is one of the useful method for modeling nonlinear
systems but PNN performance depends strongly on the number of
input variables and the order of polynomial which are determined by
trial and error. In this paper, we introduce GPNN (genetic
polynomial neural network) to improve the performance of PNN.
GPNN determines the number of input variables and the order of all
neurons with GA (genetic algorithm). We use GA to search between
all possible values for the number of input variables and the order of
polynomial. GPNN performance is obtained by two nonlinear
systems. the quadratic equation and the time series Dow Jones stock
index are two case studies for obtaining the GPNN performance.
Abstract: Deaminated lesions were produced via nitrosative oxidation of natural nucleobases; uracul (Ura, U) from cytosine (Cyt, C), hypoxanthine (Hyp, H) from adenine (Ade, A), and xanthine (Xan, X) and oxanine (Oxa, O) from guanine (Gua, G). Such damaged nucleobases may induce mutagenic problems, so that much attentions and efforts have been poured on the revealing of their mechanisms in vivo or in vitro. In this study, we employed these deaminated lesions as useful probes for analysis of DNA-binding/recognizing proteins or enzymes. Since the pyrimidine lesions such as Hyp, Oxa and Xan are employed as analogues of guanine, their comparative uses are informative for analyzing the role of Gua in DNA sequence in DNA-protein interaction. Several DNA oligomers containing such Hyp, Oxa or Xan substituted for Gua were designed to reveal the molecular interaction between DNA and protein. From this approach, we have got useful information to understand the molecular mechanisms of the DNA-recognizing enzymes, which have not ever been observed using conventional DNA oligomer composed of just natural nucleobases.
Abstract: Public awareness towards green energy are on the rise and this can be prove by many product being manufactured or prerequired to be made as energy saving devices mainly to save consumer from spending more on utility billing. These schemes are popular nowadays and many homemade appliances are turned into energy saving gadget which attracts the attention of consumers. Knowing the public demands and pattern towards purchasing home appliances thus the idea of “energy saving suction hood (ESSH)" is proposed. The ESSH can be used in many places that require smoke ventilation or even to reduce the room temperature as many conventional suction hoods (CSH) do, but this device works automatically by the usage of sensors that detects the smoke/temperature and automatically spins the exhaust fan. As it turns, the mechanical rotation rotates the AC generator which is coupled together with the fan and then charges the battery. The innovation of this product is, it does not rely on the utility supply as it is also hook up with a solar panel which also charges the battery, Secondly, it generates energy as the exhaust fan mechanically rotates. Thirdly, an energy loop back feature is introduced to this system which will supply for the ventilator fan. Another major innovation is towards interfacing this device with an in house production of generator. This generator is produced by proper design on stator as well as rotor to reduce the losses. A comparison is made between the ESSH and the CSH and result shows that the ESSH saves 172.8kWh/year of utility supply which is used by CSH. This amount of energy can save RM 3.14 from monthly utility bill and a total of RM 37.67 per year. In fact this product can generate 175 Watt of power from generator(75W) and solar panel(100W) that can be used either to supply other household appliances and/or to loop back to supply the fans motor. The innovation of this system is essential for future production of other equipment by using the loopback power method and turning most equipment into a standalone system.
Abstract: This study analyzes on the Social Network Game
(SNG), ANIPANG, in order to discover its unique fun elements, so
that suggest new methodologies for development of SNGs. ANIPANG
is the most popular SNG in the South Korea on 2012. Recently, the
game industry is paying close attention to mobile-based SNGs due to
the rapid prevalence of smart-phones and social network services.
However, SNGs are not online games simply. Although the fun of
most online games is the victory through competition with other
players or the game system, the fun of SNG is the communication
through the collaboration with other players. Thus, features of users
and environments of game should be considered for the game industry
and for the fun of SNG to users.
Abstract: The possibilities of mobile technology generate new
demands for vocational teacher trainers to transform their approach
to work and to incorporate its usage into their ordinary educational
practice. This paper presents findings of a focus discussion group
(FDG) session on the usage of iPads within a school of vocational
teacher education (SoVTE). It aims to clarify how the teacher
trainers are using iPads and what has changed in their work during
the usage of iPads. The analytical framework bases on content
analysis and expansive learning cycle. It was not only found what
kind of a role iPads played in their daily practices but it brought also
into attention how a cultural change regarding the usage of social
media and mobile technology was desperately needed in the whole
work community. Thus, the FGD was abducted for developing the
knowledge practices of the community of the SoVTE.
Abstract: Nowadays use of a new structural bracing system
called 'Knee Bracing System' have taken the specialists attention too
much. On the other hand nonlinear static analysis procedures in
estimate structures performance in earthquake time have taken
attention too much. One of these procedure is modal pushover
analysis (MPA) procedure. The accuracy of MPA procedure for
simple steel moment resisting frame has been verified and considered
in Chintanapakdee and Chopra-s article in 2003. Since the accuracy
of MPA procedure has not verified for semi-rigid steel frames with
knee bracing, we are going to get through with this matter in this
study. For this purpose, the selected structures are four frames with
different heights, 5 to 20 stories, will be designed according to AISC
criteria. Then MPA procedure is used for the same frames with
different rigidity percentiles of connections. The results of seismic
responses are compared with dynamic nonlinear response history
analysis as exact procedure and accuracy of MPA procedure is
evaluated. It seems that MPA procedure accuracy will come down by
reduction of the rigidity percentiles of semi-rigid connections.
Abstract: In this paper the development of a heat exchanger as a
pilot plant for educational purpose is discussed and the use of neural
network for controlling the process is being presented. The aim of the
study is to highlight the need of a specific Pseudo Random Binary
Sequence (PRBS) to excite a process under control. As the neural
network is a data driven technique, the method for data generation
plays an important role. In light of this a careful experimentation
procedure for data generation was crucial task. Heat exchange is a
complex process, which has a capacity and a time lag as process
elements. The proposed system is a typical pipe-in- pipe type heat
exchanger. The complexity of the system demands careful selection,
proper installation and commissioning. The temperature, flow, and
pressure sensors play a vital role in the control performance. The
final control element used is a pneumatically operated control valve.
While carrying out the experimentation on heat exchanger a welldrafted
procedure is followed giving utmost attention towards safety
of the system. The results obtained are encouraging and revealing
the fact that if the process details are known completely as far as
process parameters are concerned and utilities are well stabilized then
feedback systems are suitable, whereas neural network control
paradigm is useful for the processes with nonlinearity and less
knowledge about process. The implementation of NN control
reinforces the concepts of process control and NN control paradigm.
The result also underlined the importance of excitation signal
typically for that process. Data acquisition, processing, and
presentation in a typical format are the most important parameters
while validating the results.
Abstract: The development of sustainable utilization water resources is crucial. The ecological environment and water resources systems form the foundation of the existence and development of the social economy. The urban ecological support system depends on these resources as well. This research studies the vulnerability, criticality, and risk of climate change on water supply and demand in the main administrative district of the Taijiang Area (Tainan City). Based on the two situations set in this paper and various factors (indexes), this research adopts two kinds of weights (equal and AHP) to conduct the calculation and establish the water supply and demand risk map for the target year 2039. According to the risk analysis result, which is based on equal weight, only one district belongs to a high-grade district (Grade 4). Based on the AHP weight, 16 districts belong to a high-grade or higher-grade district (Grades 4 and 5), and from among them, two districts belong to the highest grade (Grade 5). These results show that the risk level of water supply and demand in cities is higher than that in towns. The government generally gives more attention to the adjustment strategy in the “cities." However, it should also provide proper adjustment strategies for the “towns" to be able to cope with the risks of water supply and demand.
Abstract: Emergence of smartphones brings to live the concept
of converged devices with the availability of web amenities. Such
trend also challenges the mobile devices manufactures and service
providers in many aspects, such as security on mobile phones,
complex and long time design flow, as well as higher development
cost. Among these aspects, security on mobile phones is getting more
and more attention. Microkernel based virtualization technology will
play a critical role in addressing these challenges and meeting mobile
market needs and preferences, since virtualization provides essential
isolation for security reasons and it allows multiple operating systems
to run on one processor accelerating development and cutting development
cost. However, virtualization benefits do not come for free.
As an additional software layer, it adds some inevitable virtualization
overhead to the system, which may decrease the system performance.
In this paper we evaluate and analyze the virtualization performance
cost of L4 microkernel based virtualization on a competitive mobile
phone by comparing the L4Linux, a para-virtualized Linux on top of
L4 microkernel, with the native Linux performance using lmbench
and a set of typical mobile phone applications.
Abstract: The last Assessment Report of the Intergovernmental
Panel on Climate Change, stating that the greatest risk in climate
change affects sustainability is now widely known and accepted.
However, it has not provoked substantial reaction and attention in
Hungary, while international and national efforts have also not
achieved expected results so far. Still, there are numerous examples
on different levels (national, regional, local, household) making
considerable progress in limiting their own emissions and making
steps toward mitigation of and adaptation to climate change. The
local level is exceptionally important in sustainability adaptation, as
local communities are often able to adapt more flexibly to changes in
the natural environment.The aim of this paper is to attempt a review
of the national climate policy and the local climate change strategies
in Hungary considering sustainable development.
Abstract: This study proposes a conceptual model and
empirically tests the relationships between customers and librarians
(i.e. tangibles, responsiveness, assurance, reliability and empathy)
with a dependent variable (customer satisfaction) regarding library
services. The SERVQUAL instrument was administered to 100
respondents which comprises of staff and students at a public higher
learning institution in the Federal Territory of Labuan, Malaysia.
They were public university library users. Results revealed that all
service quality dimensions tested were significant and influenced
customer satisfaction of visitors to a public university library.
Assurance is the most important factor that influences customer
satisfaction with the services rendered by the librarian. It is
imperative for the library management to take note that the top five
service attributes that gained greatest attention from library visitors-
perspective includes employee willingness to help customers,
availability of customer representatives online for response to
queries, library staff actively and promptly provide services, signs in
the building are clear and library staff are friendly and courteous.
This study provides valuable results concerning the determinants of
the service quality and customer satisfaction of public university
library services from the users' perspective.
Abstract: A trend in agent community or enterprises is that they are shifting from closed to open architectures composed of a large number of autonomous agents. One of its implications could be that interface agent framework is getting more important in multi-agent system (MAS); so that systems constructed for different application domains could share a common understanding in human computer interface (HCI) methods, as well as human-agent and agent-agent interfaces. However, interface agent framework usually receives less attention than other aspects of MAS. In this paper, we will propose an interface web agent framework which is based on our former project called WAF and a Distributed HCI template. A group of new functionalities and implications will be discussed, such as web agent presentation, off-line agent reference, reconfigurable activation map of agents, etc. Their enabling techniques and current standards (e.g. existing ontological framework) are also suggested and shown by examples from our own implementation in WAF.
Abstract: The heuristic decision rules used for project
scheduling will vary depending upon the project-s size, complexity,
duration, personnel, and owner requirements. The concept of project
complexity has received little detailed attention. The need to
differentiate between easy and hard problem instances and the
interest in isolating the fundamental factors that determine the
computing effort required by these procedures inspired a number of
researchers to develop various complexity measures.
In this study, the most common measures of project complexity are
presented. A new measure of project complexity is developed. The
main privilege of the proposed measure is that, it considers size,
shape and logic characteristics, time characteristics, resource
demands and availability characteristics as well as number of critical
activities and critical paths. The degree of sensitivity of the proposed
measure for complexity of project networks has been tested and
evaluated against the other measures of complexity of the considered
fifty project networks under consideration in the current study. The
developed measure showed more sensitivity to the changes in the
network data and gives accurate quantified results when comparing
the complexities of networks.
Abstract: Ultra-low-power (ULP) circuits have received
widespread attention due to the rapid growth of biomedical
applications and Battery-less Electronics. Subthreshold region of
transistor operation is used in ULP circuits. Major research challenge
in the subthreshold operating region is to extract the ULP benefits
with minimal degradation in speed and robustness. Process, Voltage
and Temperature (PVT) variations significantly affect the
performance of subthreshold circuits. Designed performance
parameters of ULP circuits may vary largely due to temperature
variations. Hence, this paper investigates the effect of temperature
variation on device and circuit performance parameters at different
biasing voltages in the subthreshold region. Simulation results clearly
demonstrate that in deep subthreshold and near threshold voltage
regions, performance parameters are significantly affected whereas in
moderate subthreshold region, subthreshold circuits are more
immune to temperature variations. This establishes that moderate
subthreshold region is ideal for temperature immune circuits.
Abstract: Load forecasting has become in recent years one of the major areas of research in electrical engineering. Most traditional forecasting models and artificial intelligence neural network techniques have been tried out in this task. Artificial neural networks (ANN) have lately received much attention, and a great number of papers have reported successful experiments and practical tests. This article presents the development of an ANN-based short-term load forecasting model with improved generalization technique for the Regional Power Control Center of Saudi Electricity Company, Western Operation Area (SEC-WOA). The proposed ANN is trained with weather-related data and historical electric load-related data using the data from the calendar years 2001, 2002, 2003, and 2004 for training. The model tested for one week at five different seasons, typically, winter, spring, summer, Ramadan and fall seasons, and the mean absolute average error for one hour-ahead load forecasting found 1.12%.
Abstract: The use of Electronic Commerce (EC)
technologies enables Small Medium Enterprises (SMEs) to improve their efficiency and competitive position. Much of the literature proposes an extensive set of benefits for
organizations that choose to adopt and implement ECommerce
systems. Factors of Business –to-business (B2B)
E-Commerce adoption and implementation have been
extensively investigated. Despite enormous attention given to encourage Small Medium Enterprises (SMEs) to adopt and
implement E-Commerce, little research has been carried out in identifying the factors of Business-to-Consumer ECommerce adoption and implementation for SMEs. To conduct the study, Tornatsky and Fleischer model was adopted
and tested in four SMEs located in Christchurch, New
Zealand. This paper explores the factors that impact the
decision and method of adoption and implementation of ECommerce
systems in automobile industry. Automobile
industry was chosen because the product they deal with i.e.
cars are not a common commodity to be sold online, despite this fact the eCommerce penetration in automobile industry is
high. The factors that promote adoption and implementation of
E-Commerce technologies are discussed, together with the
barriers. This study will help SME owners to effectively
handle the adoption and implementation process and will also
improve the chance of successful E-Commerce
implementation. The implications of the findings for
managers, consultants, and government organizations engaged in promoting E-Commerce adoption and implementation in
small businesses and future research are discussed.