Abstract: In this paper we present a new approach to detecting a
flaw in T.O.F.D (Time Of Flight Diffraction) type ultrasonic image
based on texture features. Texture is one of the most important
features used in recognizing patterns in an image. The paper
describes texture features based on 2D Gabor functions, i.e.,
Gaussian shaped band-pass filters, with dyadic treatment of the radial
spatial frequency range and multiple orientations, which represent an
appropriate choice for tasks requiring simultaneous measurement in
both space and frequency domains. The most relevant features are
used as input data on a Fuzzy c-mean clustering classifier. The
classes that exist are only two: 'defects' or 'no defects'. The proposed
approach is tested on the T.O.F.D image achieved at the laboratory
and on the industrial field.
Abstract: Imperfect transmission conditions modeling a thin reactive 2D interphases layer between two dissimilar bonded strips have been extracted. In this paper, the soundness of these transmission conditions for heat conduction problems are examined by the finite element method for a strong temperature-dependent source or sink and non-monotonic temperature distributions around the faces..
Abstract: The measurement of anesthetic depth is necessary in
anesthesiology. NN10 is very simple method among the RR intervals
analysis methods. NN10 parameter means the numbers of above the 10
ms intervals of the normal to normal RR intervals.
Bispectrum analysis is defined as 2D FFT. EEG signal reflected the
non-linear peristalsis phenomena according to the change brain
function. After analyzing the bispectrum of the 2 dimension, the most
significant power spectrum density peaks appeared abundantly at the
specific area in awakening and anesthesia state. These points are
utilized to create the new index since many peaks appeared at the
specific area in the frequency coordinate. The measured range of an
index was 0-100. An index is 20-50 at an anesthesia, while the index is
90-60 at the awake.
In this paper, the relation between NN10 parameter using ECG and
bisepctrum index using EEG is observed to estimate the depth of
anesthesia during anesthesia and then we estimated the utility of the
anesthetic.
Abstract: Serial hierarchical support vector machine (SHSVM)
is proposed to discriminate three brain tissues which are white matter
(WM), gray matter (GM), and cerebrospinal fluid (CSF). SHSVM
has novel classification approach by repeating the hierarchical
classification on data set iteratively. It used Radial Basis Function
(rbf) Kernel with different tuning to obtain accurate results. Also as
the second approach, segmentation performed with DAGSVM
method. In this article eight univariate features from the raw DTI data
are extracted and all the possible 2D feature sets are examined within
the segmentation process. SHSVM succeed to obtain DSI values
higher than 0.95 accuracy for all the three tissues, which are higher
than DAGSVM results.
Abstract: In this paper, a semi-fragile watermarking scheme is proposed for color image authentication. In this particular scheme, the color image is first transformed from RGB to YST color space, suitable for watermarking the color media. Each channel is divided into 4×4 non-overlapping blocks and its each 2×2 sub-block is selected. The embedding space is created by setting the two LSBs of selected sub-block to zero, which will hold the authentication and recovery information. For verification of work authentication and parity bits denoted by 'a' & 'p' are computed for each 2×2 subblock. For recovery, intensity mean of each 2×2 sub-block is computed and encoded upto six to eight bits depending upon the channel selection. The size of sub-block is important for correct localization and fast computation. For watermark distribution 2DTorus Automorphism is implemented using a private key to have a secure mapping of blocks. The perceptibility of watermarked image is quite reasonable both subjectively and objectively. Our scheme is oblivious, correctly localizes the tampering and able to recovery the original work with probability of near one.
Abstract: This paper proposes an Interactive Chinese Character
Learning System (ICCLS) based on pictorial evolution as an
edutainment concept in computer-based learning of language. The
advantage of the language origination itself is taken as a learning
platform due to the complexity in Chinese language as compared to
other types of languages. Users especially children enjoy more by
utilize this learning system because they are able to memories the
Chinese Character easily and understand more of the origin of the
Chinese character under pleasurable learning environment, compares
to traditional approach which children need to rote learning Chinese
Character under un-pleasurable environment. Skeletonization is used
as the representation of Chinese character and object with an animated
pictograph evolution to facilitate the learning of the language. Shortest
skeleton path matching technique is employed for fast and accurate
matching in our implementation. User is required to either write a
word or draw a simple 2D object in the input panel and the matched
word and object will be displayed as well as the pictograph evolution
to instill learning. The target of computer-based learning system is for
pre-school children between 4 to 6 years old to learn Chinese
characters in a flexible and entertaining manner besides utilizing
visual and mind mapping strategy as learning methodology.
Abstract: The finite-difference time-domain (FDTD) method is
one of the most widely used computational methods in
electromagnetic. This paper describes the design of two-dimensional
(2D) FDTD simulation software for transverse magnetic (TM)
polarization using Berenger's split-field perfectly matched layer
(PML) formulation. The software is developed using Matlab
programming language. Numerical examples validate the software.
Abstract: In this paper we present an approach for 3D face
recognition based on extracting principal components of range
images by utilizing modified PCA methods namely 2DPCA and
bidirectional 2DPCA also known as (2D) 2 PCA.A preprocessing
stage was implemented on the images to smooth them using median
and Gaussian filtering. In the normalization stage we locate the nose
tip to lay it at the center of images then crop each image to a standard
size of 100*100. In the face recognition stage we extract the principal
component of each image using both 2DPCA and (2D) 2 PCA.
Finally, we use Euclidean distance to measure the minimum distance
between a given test image to the training images in the database. We
also compare the result of using both methods. The best result
achieved by experiments on a public face database shows that 83.3
percent is the rate of face recognition for a random facial expression.
Abstract: The bypass exhaust system of a 160 MW combined cycle has been modeled and analyzed using numerical simulation in 2D prospective. Analysis was carried out using the commercial numerical simulation software, FLUENT 6.2. All inputs were based on the technical data gathered from working conditions of a Siemens V94.2 gas turbine, installed in the Yazd power plant. This paper deals with reduction of pressure drop in bypass exhaust system using turning vanes mounted in diverter box in order to alleviate turbulent energy dissipation rate above diverter box. The geometry of such turning vanes has been optimized based on the flow pattern at diverter box inlet. The results show that the use of optimized turning vanes in diverter box can improve the flow pattern and eliminate vortices around sharp edges just before the silencer. Furthermore, this optimization could decrease the pressure drop in bypass exhaust system and leads to higher plant efficiency.
Abstract: Numerical study of a plane jet occurring in a vertical
heated channel is carried out. The aim is to explore the influence of
the forced flow, issued from a flat nozzle located in the entry section
of a channel, on the up-going fluid along the channel walls. The
Reynolds number based on the nozzle width and the jet velocity
ranges between 3 103 and 2.104; whereas, the Grashof number based
on the channel length and the wall temperature difference is 2.57
1010. Computations are established for a symmetrically heated
channel and various nozzle positions. The system of governing
equations is solved with a finite volumes method. The obtained
results show that the jet-wall interactions activate the heat transfer,
the position variation modifies the heat transfer especially for low
Reynolds numbers: the heat transfer is enhanced for the adjacent
wall; however it is decreased for the opposite one. The numerical
velocity and temperature fields are post-processed to compute the
quantities of engineering interest such as the induced mass flow rate,
and the Nusselt number along the plates.
Abstract: Acoustic Imaging based sound localization using microphone
array is a challenging task in digital-signal processing.
Discrete Fourier transform (DFT) based near-field acoustical holography
(NAH) is an important acoustical technique for sound source
localization and provide an efficient solution to the ill-posed problem.
However, in practice, due to the usage of small curtailed aperture
and its consequence of significant spectral leakage, the DFT could
not reconstruct the active-region-of-sound (AROS) effectively, especially
near the edges of aperture. In this paper, we emphasize the
fundamental problems of DFT-based NAH, provide a solution to
spectral leakage effect by the extrapolation based on linear predictive
coding and 2D Tukey windowing. This approach has been tested to
localize the single and multi-point sound sources. We observe that
incorporating extrapolation technique increases the spatial resolution,
localization accuracy and reduces spectral leakage when small curtail
aperture with a lower number of sensors accounts.
Abstract: This paper introduces an intelligent system, which can be applied in the monitoring of vehicle speed using a single camera. The ability of motion tracking is extremely useful in many automation problems and the solution to this problem will open up many future applications. One of the most common problems in our daily life is the speed detection of vehicles on a highway. In this paper, a novel technique is developed to track multiple moving objects with their speeds being estimated using a sequence of video frames. Field test has been conducted to capture real-life data and the processed results were presented. Multiple object problems and noisy in data are also considered. Implementing this system in real-time is straightforward. The proposal can accurately evaluate the position and the orientation of moving objects in real-time. The transformations and calibration between the 2D image and the actual road are also considered.
Abstract: Two-dimensional (2D) bar codes were designed to
carry significantly more data with higher information density and
robustness than its 1D counterpart. Thanks to the popular
combination of cameras and mobile phones, it will naturally bring
great commercial value to use the camera phone for 2D bar code
reading. This paper addresses the problem of specific 2D bar code
design for mobile phones and introduces a low-level encoding
method of matrix codes. At the same time, we propose an efficient
scheme for 2D bar codes decoding, of which the effort is put on
solutions of the difficulties introduced by low image quality that is
very common in bar code images taken by a phone camera.
Abstract: Purpose: Planning and dosimetry of different VMAT algorithms (SmartArc, Ergo++, Autobeam) is compared with IMRT for Head and Neck Cancer patients. Modelling was performed to rule out the causes of discrepancies between planned and delivered dose. Methods: Five HNC patients previously treated with IMRT were re-planned with SmartArc (SA), Ergo++ and Autobeam. Plans were compared with each other and against IMRT and evaluated using DVHs for PTVs and OARs, delivery time, monitor units (MU) and dosimetric accuracy. Modelling of control point (CP) spacing, Leaf-end Separation and MLC/Aperture shape was performed to rule out causes of discrepancies between planned and delivered doses. Additionally estimated arc delivery times, overall plan generation times and effect of CP spacing and number of arcs on plan generation times were recorded. Results: Single arc SmartArc plans (SA4d) were generally better than IMRT and double arc plans (SA2Arcs) in terms of homogeneity and target coverage. Double arc plans seemed to have a positive role in achieving improved Conformity Index (CI) and better sparing of some Organs at Risk (OARs) compared to Step and Shoot IMRT (ss-IMRT) and SA4d. Overall Ergo++ plans achieved best CI for both PTVs. Dosimetric validation of all VMAT plans without modelling was found to be lower than ss-IMRT. Total MUs required for delivery were on average 19%, 30%, 10.6% and 6.5% lower than ss-IMRT for SA4d, SA2d (Single arc with 20 Gantry Spacing), SA2Arcs and Autobeam plans respectively. Autobeam was most efficient in terms of actual treatment delivery times whereas Ergo++ plans took longest to deliver. Conclusion: Overall SA single arc plans on average achieved best target coverage and homogeneity for both PTVs. SA2Arc plans showed improved CI and some OARs sparing. Very good dosimetric results were achieved with modelling. Ergo++ plans achieved best CI. Autobeam resulted in fastest treatment delivery times.
Abstract: To date, theoretical studies concerning the Carbon
Fiber Reinforced Polymer (CFRP) strengthening of RC beams with
openings have been rather limited. In addition, various numerical
analyses presented so far have effectively simulated the behaviour of
solid beam strengthened by FRP material. In this paper, a two
dimensional nonlinear finite element analysis is presented to validate
against the laboratory test results of six RC beams. All beams had the
same rectangular cross-section geometry and were loaded under four
point bending. The crack pattern results of the finite element model
show good agreement with the crack pattern of the experimental
beams. The load midspan deflection curves of the finite element
models exhibited a stiffer result compared to the experimental beams.
The possible reason may be due to the perfect bond assumption used
between the concrete and steel reinforcement.
Abstract: Multimedia courseware has been accepted as a tool
that can support teaching and learning process. 'Li2D' courseware
was developed to assist student-s visualization on the topic of Loci in
Two Dimension. This paper describes an evaluation on the
effectiveness and usability of a 'Li2D' courseware. The quasi
experiment was used for the effectiveness evaluation. Usability
evaluation was accomplished based on four constructs of usability,
namely: efficiency, learnability, screen design and satisfaction. An
evaluation on the multimedia elements was also conducted. A total of
63 students of Form Two are involved in the study. The students are
divided into two groups: control and experimental. The experimental
group had to interact with 'Li2D' courseware as part of the learning
activities while the control group used the conventional learning
methods. The results indicate that the experimental group performed
better than the control group in understanding the Loci in Two
Dimensions topic. In terms of usability, the results showed that the
students agreed on the usability in multimedia elements in the 'Li2D'
courseware.
Abstract: The segmentation of endovascular tools in fluoroscopy images can be accurately performed automatically or by minimum user intervention, using known modern techniques. It has been proven in literature, but no clinical implementation exists so far because the computational time requirements of such technology have not yet been met. A classical segmentation scheme is composed of edge enhancement filtering, line detection, and segmentation. A new method is presented that consists of a vector that propagates in the image to track an edge as it advances. The filtering is performed progressively in the projected path of the vector, whose orientation allows for oriented edge detection, and a minimal image area is globally filtered. Such an algorithm is rapidly computed and can be implemented in real-time applications. It was tested on medical fluoroscopy images from an endovascular cerebral intervention. Ex- periments showed that the 2D tracking was limited to guidewires without intersection crosspoints, while the 3D implementation was able to cope with such planar difficulties.
Abstract: Multi-agent system approach has proven to be an effective and appropriate abstraction level to construct whole models of a diversity of biological problems, integrating aspects which can be found both in "micro" and "macro" approaches when modeling this type of phenomena. Taking into account these considerations, this paper presents the important computational characteristics to be gathered into a novel bioinformatics framework built upon a multiagent architecture. The version of the tool presented herein allows studying and exploring complex problems belonging principally to structural biology, such as protein folding. The bioinformatics framework is used as a virtual laboratory to explore a minimalist model of protein folding as a test case. In order to show the laboratory concept of the platform as well as its flexibility and adaptability, we studied the folding of two particular sequences, one of 45-mer and another of 64-mer, both described by an HP model (only hydrophobic and polar residues) and coarse grained 2D-square lattice. According to the discussion section of this piece of work, these two sequences were chosen as breaking points towards the platform, in order to determine the tools to be created or improved in such a way to overcome the needs of a particular computation and analysis of a given tough sequence. The backwards philosophy herein is that the continuous studying of sequences provides itself important points to be added into the platform, to any time improve its efficiency, as is demonstrated herein.
Abstract: The main goal of this paper is to show a possibility, how to solve numerically elliptic boundary value problems arising in 2D linear elasticity by using the fictitious domain method (FDM) and the Total-FETI domain decomposition method. We briefly mention the theoretical background of these methods and demonstrate their performance on a benchmark.
Abstract: In this study the behavior of interlaminar fracture of
carbon-epoxy thermoplastic laminated composite is investigated
numerically and experimentally. Tests are performed with Arcan
specimens. Testing with Arcan specimen gives the opportunity of
utilizing just one kind of specimen for extracting fracture properties
for mode I, mode II and different mixed mode ratios of materials with
exerting load via different loading angles. Variation of loading angles
in range of 0-90° made possible to achieve different mixed mode
ratios. Correction factors for various conditions are obtained from
ABAQUS 2D finite element models which demonstrate the finite
shape of Arcan specimens used in this study. Finally, applying the
correction factors to critical loads obtained experimentally, critical
interlaminar fracture toughness of this type of carbon- epoxy
composite has been attained.