Abstract: Transient shape variation of a rotating liquid dropletis
simulated numerically. The three dimensional Navier-Stokes
equations were solved by using the level set method. The shape
variation from the sphere to the rotating ellipsoid, and to the two-robed
shapeare simulated, and the elongation of the two-robed droplet is
discussed. The two-robed shape after the initial transient is found to be
stable and the elongation is almost the same for the cases with different
initial rotation rate. The relationship between the elongation and the
rotation rate is obtained by averaging the transient shape variation. It is
shown that the elongation of two-robed shape is in good agreement
with the existing experimental data. It is found that the transient
numerical simulation is necessary for analyzing the largely elongated
two-robed shape of rotating droplet.
Abstract: Analysis for the propagation of elastic waves in
arbitrary anisotropic plates is investigated, commencing with a
formal analysis of waves in a layered plate of an arbitrary anisotropic
media, the dispersion relations of elastic waves are obtained by
invoking continuity at the interface and boundary of conditions on
the surfaces of layered plate. The obtained solutions can be used for
material systems of higher symmetry such as monoclinic,
orthotropic, transversely isotropic, cubic, and isotropic as it is
contained implicitly in the analysis. The cases of free layered plate
and layered half space are considered separately. Some special cases
have also been deduced and discussed. Finally numerical solution of
the frequency equations for an aluminum epoxy is carried out, and
the dispersion curves for the few lower modes are presented. The
results obtained theoretically have been verified numerically and
illustrated graphically.
Abstract: The characteristics of fluid flow and phase separation
in an oil-water separator were numerically analysed as part of the
work presented herein. Simulations were performed for different
velocities and droplet diameters, and the way this parameters can
influence the separator geometry was studied.
The simulations were carried out using the software package
Fluent 6.2, which is designed for numerical simulation of fluid flow
and mass transfer. The model consisted of a cylindrical horizontal
separator. A tetrahedral mesh was employed in the computational
domain. The condition of two-phase flow was simulated with the
two-fluid model, taking into consideration turbulence effects using
the k-ε model.
The results showed that there is a strong dependency of phase
separation on mixture velocity and droplet diameter. An increase in
mixture velocity will bring about a slow down in phase separation
and as a consequence will require a weir of greater height. An
increase in droplet diameter will produce a better phase separation.
The simulations are in agreement with results reported in literature
and show that CFD can be a useful tool in studying a horizontal oilwater
separator.
Abstract: We have devised a thermal carpet cloak theoretically
and implemented in silicon using layered metamaterial. The layered
metamaterial is composed of single crystalline silicon and its phononic
crystal. The design is based on a coordinate transformation. We
demonstrate the result with numerical simulation. Great cloaking
performance is achieved as a thermal insulator is well hidden under the
thermal carpet cloak. We also show that the thermal carpet cloak can
even the temperature on irregular surface. Using thermal carpet cloak
to manipulate the heat conduction is effective because of its low
complexity.
Abstract: An advanced Monte Carlo simulation method, called Subset Simulation (SS) for the time-dependent reliability prediction for underground pipelines has been presented in this paper. The SS can provide better resolution for low failure probability level with efficient investigating of rare failure events which are commonly encountered in pipeline engineering applications. In SS method, random samples leading to progressive failure are generated efficiently and used for computing probabilistic performance by statistical variables. SS gains its efficiency as small probability event as a product of a sequence of intermediate events with larger conditional probabilities. The efficiency of SS has been demonstrated by numerical studies and attention in this work is devoted to scrutinise the robustness of the SS application in pipe reliability assessment. It is hoped that the development work can promote the use of SS tools for uncertainty propagation in the decision-making process of underground pipelines network reliability prediction.
Abstract: In the present study, fracture behavior of woven
fabric-reinforced glass/epoxy composite laminates under mode III
crack growth was experimentally investigated and numerically
modeled. Two methods were used for the calculation of the strain
energy release rate: the experimental compliance calibration (CC)
method and the Virtual Crack Closure Technique (VCCT). To
achieve this aim ECT (Edge Crack Torsion) was used to evaluate
fracture toughness in mode III loading (out of plane-shear) at
different crack lengths. Load–displacement and associated energy
release rates were obtained for various case of interest. To
calculate fracture toughness JIII, two criteria were considered
including non-linearity and maximum points in load-displacement
curve and it is observed that JIII increases with the crack length
increase. Both the experimental compliance method and the virtual
crack closure technique proved applicable for the interpretation of the
fracture mechanics data of woven glass/epoxy laminates in mode III.
Abstract: This paper presents results of numerical simulation of filtration of abnormal thermoviscous fluid on an example of thermo reversible polymer gel.
Abstract: The incidence of mechanical fracture of an
automobile piston rings prompted development of fracture analysis
method on this case. The three rings (two compression rings and one
oil ring) were smashed into several parts during the power-test (after
manufacturing the engine) causing piston and liner to be damaged.
The radial and oblique cracking happened on the failed piston rings.
The aim of the fracture mechanics simulations presented in this paper
was the calculation of particular effective fracture mechanics
parameters, such as J-integrals and stress intensity factors. Crack
propagation angles were calculated as well. Two-dimensional
fracture analysis of the first compression ring has been developed in
this paper using ABAQUS CAE6.5-1 software. Moreover, SEM
fractography was developed on fracture surfaces and is discussed in
this paper. Results of numerical calculations constitute the basis for
further research on real object.
Abstract: Researches related to standard product model and
development of neutral manufacturing interfaces for numerical
control machines becomes a significant topic since the last 25 years.
In this paper, a detail description of STEP implementation on turnmill
manufacturing has been discussed. It shows requirements of
information contents from ISO14649 data model. It covers to
describe the design of STEP-NC framework applicable to turn-mill
manufacturing. In the framework, EXPRESS-G and UML modeling
tools are used to depict the information contents of the system and
established the bases of information model requirement. A product
and manufacturing data model applicable for STEP compliant
manufacturing. The next generation turn-mill operations
requirements have been represented by a UML diagram. An object
oriented classes of ISO1449 has been developed on Visual Basic dot
NET platform for binding the static information model represented
by the UML diagram. An architect of the proposed system
implementation has been given on the bases of the design and
manufacturing module of STEP-NC interface established. Finally, a
part 21 file process plan generated for an illustration of turn-mill
components.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a three-bladed
small vertical axis Darrieus wind turbine depending on blade chord
curvature with respect to rotor axis.
The adopted survey methodology is based on an analytical code
coupled to a solid modeling software, capable of generating the
desired blade geometry depending on the blade design geometric
parameters, which is linked to a finite volume CFD code for the
calculation of rotor performance.
After describing and validating the model with experimental data,
the results of numerical simulations are proposed on the bases of two
different blade profile architectures, which are respectively
characterized by a straight chord and by a curved one, having a chord
radius equal to rotor external circumference. A CFD campaign of
analysis is completed for three blade-candidate airfoil sections, that is
the recently-developed DU 06-W-200 cambered blade profile, a
classical symmetrical NACA 0021 and its derived cambered airfoil,
characterized by a curved chord, having a chord radius equal to rotor
external circumference.
The effects of blade chord curvature on angle of attack, blade
tangential and normal forces are first investigated and then the
overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of blade camber on overall rotor performance.
Abstract: The mixed oxide nuclear fuel (MOX) of U and Pu contains several percent of fission products and minor actinides, such as neptunium, americium and curium. It is important to determine accurately the decay heat from Curium isotopes as they contribute significantly in the MOX fuel. This heat generation can cause samples to melt very quickly if excessive quantities of curium are present. In the present paper, we introduce a new approach that can predict the decay heat from curium isotopes. This work is a part of the project funded by King Abdulaziz City of Science and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, and take place in King Abdulaziz University (KAU), Saudi Arabia. The approach is based on the numerical solution of coupled linear differential equations that describe decays and buildups of many nuclides to calculate the decay heat produced after shutdown. Results show the consistency and reliability of the approach applied.
Abstract: In this paper dynamics of a vapour bubble generated
due to a local energy input inside a vertical rigid cylinder and in the
absence of buoyancy forces is investigated. Different ratios of the
diameter of the rigid cylinder to the maximum radius of the bubble
are considered. The Boundary Integral Equation Method is employed
for numerical simulation of the problem. Results show that during
the collapse phase of the bubble inside a vertical rigid cylinder, two
liquid micro jets are developed on the top and bottom sides of the
vapour bubble and are directed inward. Results also show that
existence of a deposit rib inside the vertical rigid cylinder slightly
increases the life time of the bubble. It is found that by increasing the
ratio of the cylinder diameter to the maximum radius of the bubble,
the rate of the growth and collapse phases of the bubble increases
and the life time of the bubble decreases.
Abstract: Subgrade moisture content varies with environmental and soil conditions and has significant influence on pavement performance. Therefore, it is important to establish realistic estimates of expected subgrade moisture contents to account for the effects of this variable on predicted pavement performance during the design stage properly. The initial boundary soil suction profile for a given pavement is a critical factor in determining expected moisture variations in the subgrade for given pavement and climatic and soil conditions. Several numerical models have been developed for predicting water and solute transport in saturated and unsaturated subgrade soils. Soil hydraulic properties are required for quantitatively describing water and chemical transport processes in soils by the numerical models. The required hydraulic properties are hydraulic conductivity, water diffusivity, and specific water capacity. The objective of this paper was to determine isothermal moisture profiles in a soil fill and predict the soil moisture movement above the ground water table using a simple one-dimensional finite difference model.
Abstract: Scheduling for the flexible job shop is very important
in both fields of production management and combinatorial
optimization. However, it quit difficult to achieve an optimal solution
to this problem with traditional optimization approaches owing to the
high computational complexity. The combining of several
optimization criteria induces additional complexity and new
problems. In this paper, a Pareto approach to solve the multi
objective flexible job shop scheduling problems is proposed. The
objectives considered are to minimize the overall completion time
(makespan) and total weighted tardiness (TWT). An effective
simulated annealing algorithm based on the proposed approach is
presented to solve multi objective flexible job shop scheduling
problem. An external memory of non-dominated solutions is
considered to save and update the non-dominated solutions during
the solution process. Numerical examples are used to evaluate and
study the performance of the proposed algorithm. The proposed
algorithm can be applied easily in real factory conditions and for
large size problems. It should thus be useful to both practitioners and
researchers.
Abstract: The innovative fuzzy estimator is used to estimate the
ground motion acceleration of the retaining structure in this study. The
Kalman filter without the input term and the fuzzy weighting recursive
least square estimator are two main portions of this method. The
innovation vector can be produced by the Kalman filter, and be
applied to the fuzzy weighting recursive least square estimator to
estimate the acceleration input over time. The excellent performance
of this estimator is demonstrated by comparing it with the use of
difference weighting function, the distinct levels of the measurement
noise covariance and the initial process noise covariance. The
availability and the precision of the proposed method proposed in this
study can be verified by comparing the actual value and the one
obtained by numerical simulation.
Abstract: This study numerically investigates the effects of Electrohydrodynamic on flow patterns and heat transfer enhancement within a cavity which is on the lower wall of channel. In this simulation, effects of using ground wire and ground plate on the flow patterns are compared. Moreover, the positions of electrode wire respecting with ground are tested in the range of angles θ = 0 - 180o. High electrical voltage exposes to air is 20 kV. Bulk mean velocity and temperature of inlet air are controlled at 0.1 m/s and 60 OC, respectively. The result shows when electric field is applied, swirling flow is appeared in the channel. In addition, swirling flow patterns in the main flow of using ground plate are widely spreader than that of using ground wire. Moreover, direction of swirling flow also affects the flow pattern and heat transfer in a cavity. These cause the using ground wire to give the maximum temperature and heat transfer higher than using ground plate. Furthermore, when the angle is at θ = 60o, high shear flow effect is obtained. This results show high strength of swirling flow and effective heat transfer enhancement.
Abstract: In this paper, a numerical study has been made to
analyze the transient 2-D flows of a viscous incompressible fluid
through channels with forward or backward constriction. Problems
addressed include flow through sudden contraction and sudden
expansion channel geometries with rounded and increasingly sharp
reentrant corner. In both the cases, numerical results are presented for
the separation and reattachment points, streamlines, vorticity and
flow patterns. A fourth order accurate compact scheme has been
employed to efficiently capture steady state solutions of the
governing equations. It appears from our study that sharpness of the
throat in the channel is one of the important parameters to control the
strength and size of the separation zone without modifying the
general flow patterns. The comparison between the two cases shows
that the upstream geometry plays a significant role on vortex growth
dynamics.
Abstract: The theoretical prediction of the acoustical
polarization effects in the heterogeneous composites, made of thick
elastic solids with thin nematic films, is presented. The numericalanalytical
solution to the problem of the different wave propagation
exhibits some new physical effects in the low frequency domain: the
appearance of the critical frequency and the existence of the narrow
transition zone where the wave rapidly changes its speed. The
associated wave attenuation is highly perturbed in this zone. We also
show the possible appearance of the critical frequencies where the
attenuation changes the sign. The numerical results of parametrical
analysis are presented and discussed.
Abstract: The running logs of a process hold valuable
information about its executed activity behavior and generated activity
logic structure. Theses informative logs can be extracted, analyzed and
utilized to improve the efficiencies of the process's execution and
conduction. One of the techniques used to accomplish the process
improvement is called as process mining. To mine similar processes is
such an improvement mission in process mining. Rather than directly
mining similar processes using a single comparing coefficient or a
complicate fitness function, this paper presents a simplified heuristic
process mining algorithm with two similarity comparisons that are
able to relatively conform the activity logic sequences (traces) of
mining processes with those of a normalized (regularized) one. The
relative process conformance is to find which of the mining processes
match the required activity sequences and relationships, further for
necessary and sufficient applications of the mined processes to process
improvements. One similarity presented is defined by the relationships
in terms of the number of similar activity sequences existing in
different processes; another similarity expresses the degree of the
similar (identical) activity sequences among the conforming processes.
Since these two similarities are with respect to certain typical behavior
(activity sequences) occurred in an entire process, the common
problems, such as the inappropriateness of an absolute comparison and
the incapability of an intrinsic information elicitation, which are often
appeared in other process conforming techniques, can be solved by the
relative process comparison presented in this paper. To demonstrate
the potentiality of the proposed algorithm, a numerical example is
illustrated.
Abstract: In this survey the process of crack propagation at the
toe of concrete gravity dam is investigated by applying principals
and criteria of linear elastic fracture mechanic. Simulating process of
earthquake conditions for three models of dam with different
geometrical condition, in empty reservoir under plain stress is
calculated through special fracture mechanic software FRANNC2D
[1] for determining fracture mechanic criteria. The outcomes showed
that in spite of the primary expectations, the simultaneous existence
of fillet in both toe and heel area (model 3), the rate of maximum
principal stress has not been decreased; however, even the maximum
principal stress has increased, so it caused stress intensity factors
increase which is undesirable. On the other hand, the dam with heel
fillet has shown the best attitude and it is because of items like
decreasing the rates of maximum and minimum principal stresses and
also is related to decreasing the rates of stress intensity factors for 1st
& 2nd modes of the model.