Abstract: Methanol-to-olefins coupled with transformation of
coal or natural gas to methanol gives an interesting and promising way
to produce ethylene and propylene. To investigate solid concentration
in gas-solid fluidized bed for methanol-to-olefins process catalyzed by
SAPO-34, a cold model experiment system is established in this paper.
The system comprises a gas distributor in a 300mm internal diameter
and 5000mm height acrylic column, the fiber optic probe system and
series of cyclones. The experiments are carried out at ambient
conditions and under different superficial gas velocity ranging from
0.3930m/s to 0.7860m/s and different initial bed height ranging from
600mm to 1200mm. The effects of radial distance, axial distance,
superficial gas velocity, initial bed height on solid concentration in the
bed are discussed. The effects of distributor shape and porosity on
solid concentration are also discussed. The time-averaged solid
concentration profiles under different conditions are obtained.
Abstract: This paper presents a method to estimate load profile
in a multiple power flow solutions for every minutes in 24 hours per
day. A method to calculate multiple solutions of non linear profile is
introduced. The Power System Simulation/Engineering (PSS®E) and
python has been used to solve the load power flow. The result of this
power flow solutions has been used to estimate the load profiles for
each load at buses using Independent Component Analysis (ICA)
without any knowledge of parameter and network topology of the
systems. The proposed algorithm is tested with IEEE 69 test bus
system represents for distribution part and the method of ICA has
been programmed in MATLAB R2012b version. Simulation results
and errors of estimations are discussed in this paper.
Abstract: This presentation reviews recent advances in superalloys and thermal barrier coating (TBC) for application in hot sections of energy-efficient gas-turbine engines. It has been reviewed that in the modern combined-cycle gas turbines (CCGT) applying single-crystal energy materials (SC superalloys) and thermal barrier coatings (TBC), and – in one design – closed-loop steam cooling, thermal efficiency can reach more than 60%. These technological advancements contribute to profitable and clean power generation with reduced emission. Alternatively, the use of advanced superalloys (e.g. GTD-111 superalloy, Allvac 718Plus superalloy) and advanced thermal barrier coatings (TBC) in modern gas-turbines has been shown to yield higher energy-efficiency in power generation.
Abstract: In the way of growing and developing firms especially
high-tech firms, on many occasions manager of firm is mainly involved in solving problems of his business and decision making about executive activities of the firm, while besides executive
measures, attention to planning of firm's success and growth way and
application of long experience and sagacity in designing business model are vital and necessary success in a business is achieved as a
result of different factors, one of the most important of them is designing and performing an optimal business model at the beginning
of the firm's work. This model is determining the limit of profitability
achieved by innovation and gained value added. Therefore, business
model is the process of connecting innovation environment and
technology with economic environment and business and is important
for succeeding modern businesses considering their traits.
Abstract: A rigorous two-dimensional model is developed for simulating the operation of a less-investigated type steam reformer having a considerably lower operating Reynolds number, higher tube diameter, and non-availability of extra steam in the feed compared with conventional steam reformers. Simulation results show that reasonable predictions can only be achieved when certain correlations for wall to fluid heat transfer equations are applied. Due to severe operating conditions, in all cases, strong radial temperature gradients inside the reformer tubes have been found. Furthermore, the results show how a certain catalyst loading profile will affect the operation of the reformer.
Abstract: In order to monitor the water table depth on soil profile
salinity buildup, a field study was carried out during 2006-07. Wheat
(Rabi) and Sorghum (Kharif) fodder were sown in with three
treatments. The results showed that watertable depth lowered from
1.15m to 2.89 m depth at the end of experiment. With lower of
watertable depth, pH, ECe and SAR decreased under crops both
without and with gypsum and increased in fallowing. Soil moisture
depletion was directly proportional to lowering of watertable. With the
application of irrigation water (58cm) pH, ECe and SAR were reduced
in cropped plots, reduction was higher in gypsum applied plots than
non-gypsum plots. In case of fallowing, there was increase in pH, EC,
while slight reduction occurred in SAR values. However, soil salinity
showed an increasing upward trend under fallowing and its value in
0-30 cm soil layer was the highest amongst the treatments.
Abstract: Linear and weakly nonlinear analysis of shallow wake
flows is presented in the present paper. The evolution of the most
unstable linear mode is described by the complex Ginzburg-Landau
equation (CGLE). The coefficients of the CGLE are calculated
numerically from the solution of the corresponding linear stability
problem for a one-parametric family of shallow wake flows. It is
shown that the coefficients of the CGLE are not so sensitive to the
variation of the base flow profile.
Abstract: South Africa is facing a crisis with not being able to produce enough graduates in the scarce skills areas to sustain economic growth. The crisis is fuelled by a school system that does not produce enough potential students with Mathematics, Accounting and Science. Since the introduction of the new school curriculum in 2008, there is no longer an option to take pure maths on a standard grade level. Instead, only two mathematical subjects are offered: pure maths (which is on par with higher grade maths) and mathematical literacy. It is compulsory to take one or the other. As a result, lees student finishes Grade 12 with pure mathematics every year. This national problem needs urgent attention if South Africa is to make any headway in critical skills development as mathematics is a gateway to scarce skills professions. Higher education institutions initiated several initiatives in an attempt to address the above, including preparatory courses, bridging programmes and extended curricula with foundation provisions. In view of the above, and government policy directives to broaden access in the scarce skills areas to increase student throughput, foundation provision was introduced for Commerce and Information Technology programmes at the Vaal Triangle Campus (VTC) of North-West University (NWU) in 2010. Students enrolling for extended programmes do not comply with the minimum prerequisites for the normal programmes. The question then arises as to whether these programmes have the intended impact? This paper reports the results of a two year longitudinal study, tracking the first year academic achievement of the two cohorts of enrolments since 2010. The results provide valuable insight into the structuring of an extended programme and its potential impact.
Abstract: In this paper a numerical simulation of electric and
hydrodynamic fields distribution in an electrofilter for dielectric
liquids cell is made. The simulation is made with the purpose to
determine the trajectory of particles that moves under the action of
external force in an electric and hydrodynamic field created inside of
an electrofilter for dielectric liquids. Particle trajectory is analyzed
for a dielectric liquid-solid particles suspension.
Abstract: Study of soil properties like field capacity (F.C.) and permanent wilting point (P.W.P.) play important roles in study of soil moisture retention curve. Although these parameters can be measured directly, their measurement is difficult and expensive. Pedotransfer functions (PTFs) provide an alternative by estimating soil parameters from more readily available soil data. In this investigation, 70 soil samples were collected from different horizons of 15 soil profiles located in the Ziaran region, Qazvin province, Iran. The data set was divided into two subsets for calibration (80%) and testing (20%) of the models and their normality were tested by Kolmogorov-Smirnov method. Both multivariate regression and artificial neural network (ANN) techniques were employed to develop the appropriate PTFs for predicting soil parameters using easily measurable characteristics of clay, silt, O.C, S.P, B.D and CaCO3. The performance of the multivariate regression and ANN models was evaluated using an independent test data set. In order to evaluate the models, root mean square error (RMSE) and R2 were used. The comparison of RSME for two mentioned models showed that the ANN model gives better estimates of F.C and P.W.P than the multivariate regression model. The value of RMSE and R2 derived by ANN model for F.C and P.W.P were (2.35, 0.77) and (2.83, 0.72), respectively. The corresponding values for multivariate regression model were (4.46, 0.68) and (5.21, 0.64), respectively. Results showed that ANN with five neurons in hidden layer had better performance in predicting soil properties than multivariate regression.
Abstract: As one of the big government bank, Bank X is paying attention its performance, so that it can compete. One of them is the existence of organizational culture which recognized with term TIPEC (Trust, Integrity, Professionalism, Costumer Focus, and Excellence). In application of organizational culture, it is needed the existence of employee involvement (job involvement). It can be influenced by various factors, such as Locus of Control. Related to above mentioned, the problems are how employee tendency of Locus of Control, how job involvement, how organizational culture applied by employees and how influence of Locus of Control and job involvement to the organizational culture applied by employees. Researchers collected data with questioner spreading, and respondents number of 30 people. After that, the data were analyzed with SPSS software constructively. The influence of Locus of Control and job involvement to the application of organizational culture was strong, i.e. 58.3%.
Abstract: Void formation in underfill is considered as failure
in flip chip manufacturing process. Void formation possibly caused
by several factors such as poor soldering and flux residue during
die attach process, void entrapment due moisture contamination,
dispense pattern process and setting up the curing process. This
paper presents the comparison of single step and two steps curing
profile towards the void and black dots formation in underfill for
Hi-CTE Flip Chip Ceramic Ball Grid Array Package (FC-CBGA).
Statistic analysis was conducted to analyze how different factors
such as wafer lot, sawing technique, underfill fillet height and
curing profile recipe were affected the formation of voids and
black dots. A C-Mode Scanning Aqoustic Microscopy (C-SAM)
was used to scan the total count of voids and black dots. It was
shown that the 2 steps curing profile provided solution for void
elimination and black dots in underfill after curing process.
Abstract: Micro droplet formation is considered as a growing
emerging area of research due to its wide-range application in
chemistry as well as biology. The mechanism of micro droplet
formation using two immiscible liquids running through a T-junction
has been widely studied.
We believe that the flow of these two immiscible phases can be of
greater important factor that could have an impact on out-flow
hydrodynamic behavior, the droplets generated and the size of the
droplets. In this study, the type of the capillary tubes used also
represents another important factor that can have an impact on the
generation of micro droplets.
The tygon capillary tubing with hydrophilic inner surface doesn't
allow regular out-flows due to the fact that the continuous phase
doesn't adhere to the wall of the capillary inner surface.
Teflon capillary tubing, presents better wettability than tygon
tubing, and allows to obtain steady and regular regimes of out-flow,
and the micro droplets are homogeneoussize.
The size of the droplets is directly dependent on the flows of the
continuous and dispersed phases. Thus, as increasing the flow of the
continuous phase, to flow of the dispersed phase stationary, the size
of the drops decreases. Inversely, while increasing the flow of the
dispersed phase, to flow of the continuous phase stationary, the size
of the droplet increases.
Abstract: As communications systems and technology become more advanced and complex, it will be increasingly important to focus on users- individual needs. Personalization and effective user profile management will be necessary to ensure the uptake and success of new services and devices and it is therefore important to focus on the users- requirements in this area and define solutions that meet these requirements. The work on personalization and user profiles emerged from earlier ETSI work on a Universal Communications Identifier (UCI) which is a unique identifier of the user rather than a range of identifiers of the many of communication devices or services (e.g. numbers of fixed phone at home/work, mobile phones, fax and email addresses). This paper describes work on personalization including standardized information and preferences and an architectural framework providing a description of how personalization can be integrated in Next Generation Networks, together with the UCI concept.
Abstract: These days we face with so many advertisements in
magazines, those mentioned coaching is pragmatic specialties which
help people make change in their lives. Up to know Specialty coaches
are not necessarily therapists, consultants or psychologist, thus they
may not know psychological theories. The International Coach
Federation identifies "facilitating learning and results" as one of its
four core coach competencies, without understanding learning
theories coaching practice hangs in theoretical abyss. Thus the aim of
this article is investigating learning theories within coaching process.
Therefore, I reviewed some cognitive and behavioral learning
theories and analyzed their contribution with coaching process which
has been introduced in mentor coaches and ICF certified coaches'
papers and books. The result demonstrated that coaching profession
is strongly grounded in learning theories, and it will be strengthened
by the validation of theories and evidence-based research as we move
forward. Thus, it needs more research in order to applying effective
theoretical frameworks.
Abstract: Thailand-s health system is challenged by the rising
number of patients and decreasing ratio of medical
practitioners/patients, especially in rural areas. This may tempt
inexperienced GPs to rush through the process of anamnesis with the
risk of incorrect diagnosis. Patients have to travel far to the hospital
and wait for a long time presenting their case. Many patients try to
cure themselves with traditional Thai medicine. Many countries are
making use of the Internet for medical information gathering,
distribution and storage. Telemedicine applications are a relatively
new field of study in Thailand; the infrastructure of ICT had
hampered widespread use of the Internet for using medical
information. With recent improvements made health and technology
professionals can work out novel applications and systems to help
advance telemedicine for the benefit of the people. Here we explore
the use of telemedicine for people with health problems in rural areas
in Thailand and present a Telemedicine Diagnosis System for Rural
Thailand (TEDIST) for diagnosing certain conditions that people
with Internet access can use to establish contact with Community
Health Centers, e.g. by mobile phone. The system uses a Web-based
input method for individual patients- symptoms, which are taken by
an expert system for the analysis of conditions and appropriate
diseases. The analysis harnesses a knowledge base and a backward
chaining component to find out, which health professionals should be
presented with the case. Doctors have the opportunity to exchange
emails or chat with the patients they are responsible for or other
specialists. Patients- data are then stored in a Personal Health Record.
Abstract: We estimate snow velocity and snow drift density on hilly terrain under the assumption that the drifting snow mass can be represented using a micro-continuum approach (i.e. using a nonclassical mechanics approach assuming a class of fluids for which basic equations of mass, momentum and energy have been derived). In our model, the theory of coupled stress fluids proposed by Stokes [1] has been employed for the computation of flow parameters. Analyses of bulk drift velocity, drift density, drift transport and mass transport of snow particles have been carried out and computations made, considering various parametric effects. Results are compared with those of classical mechanics (logarithmic wind profile). The results indicate that particle size affects the flow characteristics significantly.
Abstract: Wheat gluten hydrolyzates (WGHs) and anchovy fine
powder hydrolyzates (AFPHs) were produced at 300 MPa using
combinations of Flavourzyme 500MG (F), Alcalase 2.4L (A),
Marugoto E (M) and Protamex (P), and then were compared to those
produced at ambient pressure concerning the contents of soluble solid
(SS), soluble nitrogen and electrophoretic profiles. The contents of SS
in the WGHs and AFPHs increased up to 87.2% according to the
increase in enzyme number both at high and ambient pressure. Based
on SS content, the optimum enzyme combinations for one-, two-,
three- and four-enzyme hydrolysis were determined as F, FA, FAM
and FAMP, respectively. Similar trends were found for the contents of
total soluble nitrogen (TSN) and TCA-soluble nitrogen (TCASN). The
contents of SS, TSN and TCASN in the hydrolyzates together with
electrophoretic mobility maps indicates that the high-pressure
treatment of this study accelerated protein hydrolysis compared to
ambient-pressure treatment.
Abstract: Investment in a constructed facility represents a cost in
the short term that returns benefits only over the long term use of the
facility. Thus, the costs occur earlier than the benefits, and the owners
of facilities must obtain the capital resources to finance the costs of
construction. A project cannot proceed without an adequate
financing, and the cost of providing an adequate financing can be
quite large. For these reasons, the attention to the project finance is an
important aspect of project management. Finance is also a concern to
the other organizations involved in a project such as the general
contractor and material suppliers. Unless an owner immediately and
completely covers the costs incurred by each participant, these
organizations face financing problems of their own. At a more
general level, the project finance is the only one aspect of the general
problem of corporate finance. If numerous projects are considered
and financed together, then the net cash flow requirements constitute
the corporate financing problem for capital investment. Whether
project finance is performed at the project or at the corporate level
does not alter the basic financing problem .In this paper, we will first
consider facility financing from the owner's perspective, with due
consideration for its interaction with other organizations involved in a
project. Later, we discuss the problems of construction financing
which are crucial to the profitability and solvency of construction
contractors. The objective of this paper is to present the steps utilized
to determine the best combination of minimum project financing.
The proposed model considers financing; schedule and maximum net
area .The proposed model is called Project Financing and Schedule
Integration using Genetic Algorithms "PFSIGA". This model
intended to determine more steps (maximum net area) for any project
with a subproject. An illustrative example will demonstrate the
feature of this technique. The model verification and testing are put
into consideration.
Abstract: Introducing survivability into embedded real-time system (ERTS) can improve the survivability power of the system. This paper mainly discusses about the survivability of ERTS. The first is the survivability origin of ERTS. The second is survivability analysis. According to the definition of survivability based on survivability specification and division of the entire survivability analysis process for ERTS, a survivability analysis profile is presented. The quantitative analysis model of this profile is emphasized and illuminated in detail, the quantifying analysis of system was showed helpful to evaluate system survivability more accurate. The third is platform design of survivability analysis. In terms of the profile, the analysis process is encapsulated and assembled into one platform, on which quantification, standardization and simplification of survivability analysis are all achieved. The fourth is survivability design. According to character of ERTS, strengthened design method is selected to realize system survivability design. Through the analysis of embedded mobile video-on-demand system, intrusion tolerant technology is introduced in whole survivability design.