Abstract: Numerical studies were conducted using Lattice
Boltzmann Method (LBM) to study the natural convection in a square
cavity in the presence of roughness. An algorithm based on a single
relaxation time Bhatnagar-Gross-Krook (BGK) model of Lattice
Boltzmann Method (LBM) was developed. Roughness was
introduced on both the hot and cold walls in the form of sinusoidal
roughness elements. The study was conducted for a Newtonian fluid
of Prandtl number (Pr) 1.0. The range of Ra number was explored
from 10^3 to 10^6 in a laminar region. Thermal and hydrodynamic
behavior of fluid was analyzed using a differentially heated square
cavity with roughness elements present on both the hot and cold wall.
Neumann boundary conditions were introduced on horizontal walls
with vertical walls as isothermal. The roughness elements were at the
same boundary condition as corresponding walls. Computational
algorithm was validated against previous benchmark studies
performed with different numerical methods, and a good agreement
was found to exist. Results indicate that the maximum reduction in
the average heat transfer was 16.66 percent at Ra number 10^5.
Abstract: In this paper, we used data mining to extract
biomedical knowledge. In general, complex biomedical data
collected in studies of populations are treated by statistical methods,
although they are robust, they are not sufficient in themselves to
harness the potential wealth of data. For that you used in step two
learning algorithms: the Decision Trees and Support Vector Machine
(SVM). These supervised classification methods are used to make the
diagnosis of thyroid disease. In this context, we propose to promote
the study and use of symbolic data mining techniques.
Abstract: Paints are the most widely used methods of protection
against atmospheric corrosion of metals. The aim of this work was to
determine the protective performance of epoxy coating against sea
water before and after damage.
Investigations are conducted using stationary and non-stationary
electrochemical tools such as electrochemical impedance
spectroscopy has allowed us to characterize the protective qualities of
these films. The application of the EIS on our damaged in-situ
painting shows the existence of several capacitive loops which is an
indicator of the failure of our tested paint. Microscopic analysis
(micrograph) helped bring essential elements in understanding the
degradation of our paint condition and immersion training corrosion
products.
Abstract: This article deals with geographical conditions in
terrain and their effect on the movement of vehicles, their effect on
speed and safety of movement of people and vehicles. Finding of the
optimal routes outside the communication is studied in the Army
environment, but it occur in civilian as well, primarily in crisis
situation, or by the provision of assistance when natural disasters
such as floods, fires, storms etc., have happened. These movements
require the optimization of routes when effects of geographical
factors should be included. The most important factor is the surface
of a terrain. It is based on several geographical factors as are slopes,
soil conditions, micro-relief, a type of surface and meteorological
conditions. Their mutual impact has been given by coefficient of
deceleration. This coefficient can be used for the commander`s
decision. New approaches and methods of terrain testing,
mathematical computing, mathematical statistics or cartometric
investigation are necessary parts of this evaluation.
Abstract: Over the past few years, the online multimedia
collection has grown at a fast pace. Several companies showed
interest to study the different ways to organise the amount of audio
information without the need of human intervention to generate
metadata. In the past few years, many applications have emerged on
the market which are capable of identifying a piece of music in a
short time. Different audio effects and degradation make it much
harder to identify the unknown piece. In this paper, an audio
fingerprinting system which makes use of a non-parametric based
algorithm is presented. Parametric analysis is also performed using
Gaussian Mixture Models (GMMs). The feature extraction methods
employed are the Mel Spectrum Coefficients and the MPEG-7 basic
descriptors. Bin numbers replaced the extracted feature coefficients
during the non-parametric modelling. The results show that nonparametric
analysis offer potential results as the ones mentioned in
the literature.
Abstract: The aim of this paper is to select the most accurate
forecasting method for predicting the future values of the
unemployment rate in selected European countries. In order to do so,
several forecasting techniques adequate for forecasting time series
with trend component, were selected, namely: double exponential
smoothing (also known as Holt`s method) and Holt-Winters` method
which accounts for trend and seasonality. The results of the empirical
analysis showed that the optimal model for forecasting
unemployment rate in Greece was Holt-Winters` additive method. In
the case of Spain, according to MAPE, the optimal model was double
exponential smoothing model. Furthermore, for Croatia and Italy the
best forecasting model for unemployment rate was Holt-Winters`
multiplicative model, whereas in the case of Portugal the best model
to forecast unemployment rate was Double exponential smoothing
model. Our findings are in line with European Commission
unemployment rate estimates.
Abstract: The elastic period has a primary role in the seismic
assessment of buildings. Reliable calculations and/or estimates of the
fundamental frequency of a building and its site are essential during
analysis and design process. Various code formulas based on
empirical data are generally used to estimate the fundamental
frequency of a structure. For existing structures, in addition to code
formulas and available analytical tools such as modal analyses,
various methods of testing including ambient and forced vibration
testing procedures may be used to determine dynamic characteristics.
In this study, the dynamic properties of the 32 buildings located in
the Madinah of Saudi Arabia were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Ambient vibration measurements of buildings have been
analyzed and the fundamental longitudinal and transverse periods for
all tested buildings are presented. The fundamental mode of vibration
has been compared in plots with codes formulae (Saudi Building
Code, EC8, and UBC1997). The results indicate that measured
periods of existing buildings are shorter than that given by most
empirical code formulas. Recommendations are given based on the
common design and construction practice in Madinah city.
Abstract: Livestock is one of the fastest-growing sectors in
agriculture. If carefully managed, have potential opportunities for
economic growth, food sovereignty and food security. In this study
we mainly analyse and compare long-term i.e. for year 2030 climate
variability impact on predicted productivity of meat i.e. beef, mutton
and poultry for the Kingdom of Saudi Arabia w.r.t three factors i.e. i)
climatic-change vulnerability ii) CO2 fertilization and iii) water
scarcity and compare the results with two countries of the region i.e.
Iraq and Yemen. We do the analysis using data from diverse sources,
which was extracted, transformed and integrated before usage. The
collective impact of the three factors had an overall negative effect on
the production of meat for all the three countries, with adverse impact
on Iraq. High similarity was found between CO2 fertilization
(effecting animal fodder) and water scarcity i.e. higher than that
between production of beef and mutton for the three countries
considered. Overall, the three factors do not seem to be favorable for
the three Middle-East countries considered. This points to possibility
of a vegetarian year 2030 based on dependency on indigenous livestock
population.
Abstract: Moodle is an open source learning management
system that enables creation of a powerful and flexible learning
environment. Many organizations, especially learning institutions
have customized Moodle open source LMS for their own use. In
general open source LMSs are of great interest due to many
advantages they offer in terms of cost, usage and freedom to
customize to fit a particular context. Tanzania Secondary School e-
Learning (TanSSe-L) system is the learning management system for
Tanzania secondary schools. TanSSe-L system was developed using
a number of methods, one of them being customization of Moodle
Open Source LMS. This paper presents few areas on the way Moodle
OS LMS was customized to produce a functional TanSSe-L system
fitted to the requirements and specifications of Tanzania secondary
schools’ context.
Abstract: In review the generalized data about different methods
of synthesis of biological activity halogenated di-, tri- and tetrahydroxyanthraquinones
is presented. The basic regularity of a
synthesis is analyzed. Action of temperature, pH, solubility, catalysts
and other factors on a reaction product yield is revealed.
Abstract: Blueberries are widely valued for their high content in
phenolic compounds with antioxidant activity, and hence beneficial
for the human health. In this way, a study was done to determine the
phenolic composition (total phenols, anthocyanins and tannins) and
antioxidant activity of blueberries from three cultivars (Duke,
Bluecrop, and Ozarkblue) grown in two different Portuguese farms.
Initially two successive extractions were done with methanol
followed by two extractions with aqueous acetone solutions. These
extracts obtained were then used to evaluate the amount of phenolic
compounds and the antioxidant activity. The total phenols were
observed to vary from 4.9 to 8.2 mg GAE/g fresh weight, with
anthocyanin’s contents in the range 1.5-2.8 mg EMv3G/g and tannins
contents in the range 1.5- 3.8 mg/g. The results for antioxidant
activity ranged from 9.3 to 23.2 molTE/g and from 24.7 to 53.4molTE/g, when measured, respectively, by DPPH and ABTS
methods. In conclusion it was observed that, in general, the cultivar
had a visible effect on the phenols present, and furthermore, the
geographical origin showed relevance either in the phenols contents
or the antioxidant activity.
Abstract: In this paper, groundwater seepage into Amirkabir
tunnel has been estimated using analytical and numerical methods for
14 different sections of the tunnel. Site Groundwater Rating (SGR)
method also has been performed for qualitative and quantitative
classification of the tunnel sections. The obtained results of above
mentioned methods were compared together. The study shows
reasonable accordance with results of the all methods unless for two
sections of tunnel. In these two sections there are some significant
discrepancies between numerical and analytical results mainly
originated from model geometry and high overburden. SGR and the
analytical and numerical calculations, confirm high concentration of
seepage inflow in fault zones. Maximum seepage flow into tunnel has
been estimated 0.425 lit/sec/m using analytical method and 0.628
lit/sec/m using numerical method occured in crashed zone. Based on
SGR method, six sections of 14 sections in Amirkabir tunnel axis are
found to be in "No Risk" class that is supported by the analytical and
numerical seepage value of less than 0.04 lit/sec/m.
Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: Standard processes, similar and limited production
lines, the production of high direct costs will be more accurate than
the use of parts of the traditional cost systems in the literature.
However, direct costs, overhead expenses, in turn, decrease the
burden of increasingly sophisticated production facilities, a situation
that led the researchers to look for the cost of traditional systems of
alternative techniques. Variety cost management approaches for
example Total quality management (TQM), just-in-time (JIT),
benchmarking, kaizen costing, targeting cost, life cycle costs (LLC),
activity-based costing (ABC) value engineering have been
introduced. Management and cost applications have changed over the
past decade and will continue to change. Modern cost systems can
provide relevant and accurate cost information. These methods
provide the decisions about customer, product and process
improvement. The aim of study is to describe and explain the
adoption and application of costing systems in SME. This purpose
reports on a survey conducted during 2014 small and medium sized
enterprises (SME) in Ankara. The survey results were evaluated
using SPSS18 package program.
Abstract: This study aims to investigate the possibility of crime
prevention through CCTV by analyzing the appropriateness of the
CCTV location, whether it is installed in the hotspot of crime-prone
areas, and exploring the crime prevention effect and transition effect.
The real crime and CCTV locations of case city were converted into
the spatial data by using GIS. The data was analyzed by hotspot
analysis and weighted displacement quotient (WDQ). As study
methods, it analyzed existing relevant studies for identifying the trends
of CCTV and crime studies based on big data from 1800 to 2014 and
understanding the relation between CCTV and crime. Second, it
investigated the current situation of nationwide CCTVs and analyzed
the guidelines of CCTV installation and operation to draw attention to
the problems and indicating points of CCTV use. Third, it investigated
the crime occurrence in case areas and the current situation of CCTV
installation in the spatial aspects, and analyzed the appropriateness and
effectiveness of CCTV installation to suggest a rational installation of
CCTV and the strategic direction of crime prevention. The results
demonstrate that there was no significant effect in the installation of
CCTV on crime prevention in the case area. This indicates that CCTV
should be installed and managed in a more scientific way reflecting
local crime situations. In terms of CCTV, the methods of spatial
analysis such as GIS, which can evaluate the installation effect, and the
methods of economic analysis like cost-benefit analysis should be
developed. In addition, these methods should be distributed to local
governments across the nation for the appropriate installation of
CCTV and operation. This study intended to find a design guideline of
the optimum CCTV installation. In this regard, this study is
meaningful in that it will contribute to the creation of a safe city.
Abstract: This paper consider the solution of the matrix
differential models using quadratic, cubic, quartic, and quintic
splines. Also using the Taylor’s and Picard’s matrix methods, one
illustrative example is included.
Abstract: Experimental & numeral study of temperature
distribution during milling process, is important in milling quality
and tools life aspects. In the present study the milling cross-section
temperature is determined by using Artificial Neural Networks
(ANN) according to the temperature of certain points of the work
piece and the point specifications and the milling rotational speed of
the blade. In the present work, at first three-dimensional model of the
work piece is provided and then by using the Computational Heat
Transfer (CHT) simulations, temperature in different nods of the
work piece are specified in steady-state conditions. Results obtained
from CHT are used for training and testing the ANN approach. Using
reverse engineering and setting the desired x, y, z and the milling
rotational speed of the blade as input data to the network, the milling
surface temperature determined by neural network is presented as
output data. The desired points temperature for different milling
blade rotational speed are obtained experimentally and by
extrapolation method for the milling surface temperature is obtained
and a comparison is performed among the soft programming ANN,
CHT results and experimental data and it is observed that ANN soft
programming code can be used more efficiently to determine the
temperature in a milling process.
Abstract: The aim of this study was to build ‘Ubi-Net’, a
decision-making support system for systematic establishment in
U-City planning. We have experienced various urban problems caused
by high-density development and population concentrations in
established urban areas. To address these problems, a U-Service
contributes to the alleviation of urban problems by providing real-time
information to citizens through network connections and related
information. However, technology, devices, and information for
consumers are required for systematic U-Service planning in towns
and cities where there are many difficulties in this regard, and a lack of
reference systems.
Thus, this study suggests methods to support the establishment of
sustainable planning by providing comprehensive information
including IT technology, devices, news, and social networking
services (SNS) to U-City planners through intelligent searches. In this
study, we targeted Smart U-Parking Planning to solve parking
problems in an ‘old’ city. Through this study, we sought to contribute
to supporting advances in U-Space and the alleviation of urban
problems.
Abstract: The goal of image segmentation is to cluster pixels
into salient image regions. Segmentation could be used for object
recognition, occlusion boundary estimation within motion or stereo
systems, image compression, image editing, or image database lookup.
In this paper, we present a color image segmentation using
support vector machine (SVM) pixel classification. Firstly, the pixel
level color and texture features of the image are extracted and they
are used as input to the SVM classifier. These features are extracted
using the homogeneity model and Gabor Filter. With the extracted
pixel level features, the SVM Classifier is trained by using FCM
(Fuzzy C-Means).The image segmentation takes the advantage of
both the pixel level information of the image and also the ability of
the SVM Classifier. The Experiments show that the proposed method
has a very good segmentation result and a better efficiency, increases
the quality of the image segmentation compared with the other
segmentation methods proposed in the literature.
Abstract: Operations, maintenance and reliability of wind
turbines have received much attention over the years due to the rapid
expansion of wind farms. This paper explores early fault diagnosis
technique for a 5MW wind turbine system subjected to multiple
faults, where genetic optimization algorithm is employed to make the
residual sensitive to the faults, but robust against disturbances. The
proposed technique has a potential to reduce the downtime mostly
caused by the breakdown of components and exploit the productivity
consistency by providing timely fault alarms. Simulation results show
the effectiveness of the robust fault detection methods used under
Matlab/Simulink/Gatool environment.