Abstract: Measurement of the COD of a spent caustic solution involves firstly digestion of a test sample with dichromate solution and secondly measurement of dichromate remained by titration by ferrous ammonium sulfate [FAS] to an end point. In this paper we study by a potentiometric end point with Ag/AgCl reference electrode and gold rode electrode. The potentiometric end point is sharp and easily identified especially for the samples with high turbidity and color that other methods such as colorimetric in this type of sample do not result in high precision. Because interim of titration responds quickly to potential changes within the [Cr+6/Cr+3& Fe+2/Fe+3] solution producing stable readings that is lead to accurate COD measurement. Finally results are compared with data determined using colorimetric method for standard samples. It is shown that the potentiometric end point titration with gold rode electrode can be used with equal or better facility
Abstract: This paper proposes an improvement method of classification
efficiency in a classification model. The model is used
in a risk search system and extracts specific labels from articles
posted at bulletin board sites. The system can analyze the important
discussions composed of the articles. The improvement method
introduces ensemble learning methods that use multiple classification
models. Also, it introduces expressions related to the specific labels
into generation of word vectors. The paper applies the improvement
method to articles collected from three bulletin board sites selected
by users and verifies the effectiveness of the improvement method.
Abstract: Fractional delay FIR filters design method based on
the differential evolution algorithm is presented. Differential evolution
is an evolutionary algorithm for solving a global optimization problems in the continuous search space. In the proposed approach,
an evolutionary algorithm is used to determine the coefficients of
a fractional delay FIR filter based on the Farrow structure. Basic
differential evolution is enhanced with a restricted mating technique,
which improves the algorithm performance in terms of convergence
speed and obtained solution. Evolutionary optimization is carried out by minimizing an objective function which is based on the amplitude
response and phase delay errors. Experimental results show that the proposed algorithm leads to a reduction in the amplitude response and phase delay errors relative to those achieved with the Least-Squares
method.
Abstract: Truss optimization problem has been vastly studied
during the past 30 years and many different methods have been
proposed for this problem. Even though most of these methods
assume that the design variables are continuously valued, in reality,
the design variables of optimization problems such as cross-sectional
areas are discretely valued. In this paper, an improved hill climbing
and an improved simulated annealing algorithm have been proposed
to solve the truss optimization problem with discrete values for crosssectional
areas. Obtained results have been compared to other
methods in the literature and the comparison represents that the
proposed methods can be used more efficiently than other proposed
methods
Abstract: The sustainability of a place depends on a series of factors which contribute to the quality of life, sense of place and recognition of identity. An activity like walking, which in itself is obviously ''sustainable'', can become non sustainable if the context in which it is carried out does not meet the conditions for an adequate quality of life. This work is aimed at proposing the analytical method of Place Maker to identify the elements that do not feature in traditional mapping and which constitute the contemporary identity of the places, and the relative complex map to represent those elements and support sustainable urban identity design. The method's potential for areas with a predominantly pedestrian vocation is illustrated by means of the case study of the Ramblas in Barcelona.
Abstract: This paper aims to explain the project carried out at
the University of Cordoba, specifically at the High Polytechnic
School in collaboration with two other organizations belonging to the
Andalusian Ministry of Innovation, Science and Business:
Andalusian Innovation and Development Agency (IDEA agency) [1]
and the Territorial Net of Entrepreneurship Support (in Spanish Red
Territorial de Apoyo al Emprendedor) [11].
The project is being developed in several stages of which only the
first one has already been completed. However, several important
preliminary results derive from it, based mainly in the description of
the nature of entrepreneurship in the field of university education and
its impact on student-s competency as recommended by the European
Higher Education Area. Some problems holding back the correct
future development will also be shown as derived from the specific
context of application of the project.
Abstract: Roundabout work on the principle of circulation and
entry flows, where the maximum entry flow rates depend largely on
circulating flow bearing in mind that entry flows must give away to
circulating flows. Where an existing roundabout has a road hump
installed at the entry arm, it can be hypothesized that the kinematics
of vehicles may prevent the entry arm from achieving optimum
performance. Road humps are traffic calming devices placed across
road width solely as speed reduction mechanism. They are the
preferred traffic calming option in Malaysia and often used on single
and dual carriageway local routes. The speed limit on local routes is
30mph (50 km/hr). Road humps in their various forms achieved the
biggest mean speed reduction (based on a mean speed before traffic
calming of 30mph) of up to 10mph or 16 km/hr according to the UK
Department of Transport. The underlying aim of reduced speed
should be to achieve a 'safe' distribution of speeds which reflects the
function of the road and the impacts on the local community.
Constraining safe distribution of speeds may lead to poor drivers
timing and delayed reflex reaction that can probably cause accident.
Previous studies on road hump impact have focused mainly on speed
reduction, traffic volume, noise and vibrations, discomfort and delay
from the use of road humps. The paper is aimed at optimal entry and
circulating flow induced by road humps. Results show that
roundabout entry and circulating flow perform better in
circumstances where there is no road hump at entrance.
Abstract: This paper introduces a hand gesture recognition system to recognize real time gesture in unstrained environments. Efforts should be made to adapt computers to our natural means of communication: Speech and body language. A simple and fast algorithm using orientation histograms will be developed. It will recognize a subset of MAL static hand gestures. A pattern recognition system will be using a transforrn that converts an image into a feature vector, which will be compared with the feature vectors of a training set of gestures. The final system will be Perceptron implementation in MATLAB. This paper includes experiments of 33 hand postures and discusses the results. Experiments shows that the system can achieve a 90% recognition average rate and is suitable for real time applications.
Abstract: The purpose of this paper is to present two different
approaches of financial distress pre-warning models appropriate for
risk supervisors, investors and policy makers. We examine a sample
of the financial institutions and electronic companies of Taiwan
Security Exchange (TSE) market from 2002 through 2008. We
present a binary logistic regression with paned data analysis. With
the pooled binary logistic regression we build a model including
more variables in the regression than with random effects, while the
in-sample and out-sample forecasting performance is higher in
random effects estimation than in pooled regression. On the other
hand we estimate an Adaptive Neuro-Fuzzy Inference System
(ANFIS) with Gaussian and Generalized Bell (Gbell) functions and
we find that ANFIS outperforms significant Logit regressions in both
in-sample and out-of-sample periods, indicating that ANFIS is a
more appropriate tool for financial risk managers and for the
economic policy makers in central banks and national statistical
services.
Abstract: Carbon nanotubes (CNTs) with their high mechanical,
electrical, thermal and chemical properties are regarded as promising
materials for many different potential applications. Having unique
properties they can be used in a wide range of fields such as
electronic devices, electrodes, drug delivery systems, hydrogen
storage, textile etc. Catalytic chemical vapor deposition (CCVD) is a
common method for CNT production especially for mass production.
Catalysts impregnated on a suitable substrate are important for
production with chemical vapor deposition (CVD) method. Iron
catalyst and MgO substrate is one of most common catalyst-substrate
combination used for CNT. In this study, CNTs were produced by
CCVD of acetylene (C2H2) on magnesium oxide (MgO) powder
substrate impregnated by iron nitrate (Fe(NO3)3•9H2O) solution. The
CNT synthesis conditions were as follows: at synthesis temperatures
of 500 and 800°C multiwall and single wall CNTs were produced
respectively. Iron (Fe) catalysts were prepared by with Fe:MgO ratio
of 1:100, 5:100 and 10:100. The duration of syntheses were 30 and
60 minutes for all temperatures and catalyst percentages. The
synthesized materials were characterized by thermal gravimetric
analysis (TGA), transmission electron microscopy (TEM) and Raman
spectroscopy.
Abstract: This paper aims to (1) analyze the profiles of
transgressors (detected evaders); (2) examine reason(s) that triggered a
tax audit, causes of tax evasion, audit timeframe and tax penalty
charged; and (3) to assess if tax auditors followed the guidelines as
stated in the 'Tax Audit Framework' when conducting tax audits. In
2011, the Inland Revenue Board Malaysia (IRBM) had audited and
finalized 557 company cases. With official permission, data of all the
557 cases were obtained from the IRBM. Of these, a total of 421 cases
with complete information were analyzed. About 58.1% was small and
medium corporations and from the construction industry (32.8%). The
selection for tax audit was based on risk analysis (66.8%), information
from third party (11.1%), and firm with low profitability or fluctuating
profit pattern (7.8%). The three persistent causes of tax evasion by
firms were over claimed expenses (46.8%), fraudulent reporting of
income (38.5%) and overstating purchases (10.5%). These findings
are consistent with past literature. Results showed that tax auditors
took six to 18 months to close audit cases. More than half of tax
evaders were fined 45% on additional tax raised during audit for the
first offence. The study found tax auditors did follow the guidelines in
the 'Tax Audit Framework' in audit selection, settlement and penalty
imposition.
Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: This paper presents an investigation of the power
penalties imposed by four-wave mixing (FWM) on G.652 (Single-
Mode Fiber - SMF), G.653 (Dispersion-Shifted Fiber - DSF), and
G.655 (Non-Zero Dispersion-Shifted Fiber - NZDSF) compliant
fibers, considering the DWDM grids suggested by the ITU-T
Recommendations G.692, and G.694.1, with uniform channel
spacing of 100, 50, 25, and 12.5 GHz. The mathematical/numerical
model assumes undepleted pumping, and shows very clearly the
deleterious effect of FWM on the performance of DWDM systems,
measured by the signal-to-noise ratio (SNR). The results make it
evident that non-uniform channel spacing is practically mandatory
for WDM systems based on DSF fibers.
Abstract: The aim of this study is evaluating the antinociceptive
and anti-inflamatory activity of Geum kokanicum. After
determination total extract LD50, different doses of extract were
chosen for intrapritoneal injections. In inflammation test, male NMRI
mice were divided into 6 groups: control (normal saline), positive
control (Dexamethasone 15mg/kg), and total extract (0.025, 0.05,
0.1, and 0.2 gr/kg). The inflammation was produced by xyleneinduced
edema. In order to evaluate the antinociceptive effect of total
extract, formalin test was used. Mice were divided into 6 groups:
control, positive control (morphine 10mg/kg), and 4 groups which
received total extract. Then they received Formalin. The animals
were observed for the reaction to pain. Data were analyzed using
One-way ANOVA followed by Tukey-Kramer multiple comparison
test. LD50 was 1 gr/kg. Data indicated that 0.5,0.1 and 0.2 gr/kg
doses of total extract have particular antinociceptive and antiinflammatory
effects in a comparison with control (P
Abstract: In this paper, we consider the almost periodic solutions of a discrete cooperation system with feedback controls. Assuming that the coefficients in the system are almost periodic sequences, we obtain the existence and uniqueness of the almost periodic solution which is uniformly asymptotically stable.
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: One important problem in today organizations is the
existence of non-integrated information systems, inconsistency and
lack of suitable correlations between legacy and modern systems.
One main solution is to transfer the local databases into a global one.
In this regards we need to extract the data structures from the legacy
systems and integrate them with the new technology systems. In
legacy systems, huge amounts of a data are stored in legacy
databases. They require particular attention since they need more
efforts to be normalized, reformatted and moved to the modern
database environments. Designing the new integrated (global)
database architecture and applying the reverse engineering requires
data normalization. This paper proposes the use of database reverse
engineering in order to integrate legacy and modern databases in
organizations. The suggested approach consists of methods and
techniques for generating data transformation rules needed for the
data structure normalization.