Abstract: This study was conducted to evaluate the manganese
removal from aqueous solution using Banana peels activated carbon
(BPAC). Batch experiments have been carried out to determine the
influence of parameters such as pH, biosorbent dose, initial metal ion
concentrations and contact times on the biosorption process. From
these investigations, a significant increase in percentage removal of
manganese 97.4% is observed at pH value 5.0, biosorbent dose 0.8 g,
initial concentration 20 ppm, temperature 25 ± 2°C, stirring rate 200
rpm and contact time 2h. The equilibrium concentration and the
adsorption capacity at equilibrium of the experimental results were
fitted to the Langmuir and Freundlich isotherm models; the Langmuir
isotherm was found to well represent the measured adsorption data
implying BPAC had heterogeneous surface. A raw groundwater
samples were collected from Baharmos groundwater treatment plant
network at Embaba and Manshiet Elkanater City/District-Giza,
Egypt, for treatment at the best conditions that reached at first phase
by BPAC. The treatment with BPAC could reduce iron and
manganese value of raw groundwater by 91.4% and 97.1%,
respectively and the effect of the treatment process on the
microbiological properties of groundwater sample showed decrease
of total bacterial count either at 22°C or at 37°C to 85.7% and 82.4%,
respectively. Also, BPAC was characterized using SEM and FTIR
spectroscopy.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive (UI) single phase inverter (SPI) for a
photovoltaic (PV) system at residential/distribution level. The
proposed model uses single-phase phase locked loop (PLL) to
synchronize SPI with the grid and performs MPC control in a dq
reference frame. SPI model consists of boost converter (BC),
maximum power point tracking (MPPT) control, and a full bridge
(FB) voltage source inverter (VSI). No PI regulators to tune and
carrier and modulating waves are required to produce switching
sequence. Instead, the operational model of VSI is used to synthesize
sinusoidal current and track the reference. Model is validated using a
three kW PV system at the input of UI-SPI in Matlab/Simulink.
Implementation and results demonstrate simplicity and accuracy, as
well as reliability of the model.
Abstract: Economic Dispatch (ED) is one of the most
challenging problems of power system since it is difficult to determine
the optimum generation scheduling to meet the particular load demand
with the minimum fuel costs while all constraints are satisfied. The
objective of the Economic Dispatch Problems (EDPs) of electric
power generation is to schedule the committed generating units
outputs so as to meet the required load demand at minimum operating
cost while satisfying all units and system equality and inequality
constraints. In this paper, an efficient and practical steady-state genetic
algorithm (SSGAs) has been proposed for solving the economic
dispatch problem. The objective is to minimize the total generation
fuel cost and keep the power flows within the security limits. To
achieve that, the present work is developed to determine the optimal
location and size of capacitors in transmission power system where,
the Participation Factor Algorithm and the Steady State Genetic
Algorithm are proposed to select the best locations for the capacitors
and determine the optimal size for them.
Abstract: A circularly polarized fractal boundary microstrip
antenna is presented. The sides of a square patch along x- axis, yaxis
are replaced with Minkowski and Koch curves correspondingly.
By using the fractal curves as edges, asymmetry in the structure is
created to excite two orthogonal modes for circular polarization (CP)
operation. The indentation factors of the fractal curves are optimized
for pure CP. The simulated results of the novel polyfractal antenna
are demonstrated.
Abstract: Cognitive Radio is a turning out technology that
empowers viable usage of the spectrum. Energy Detector-based
Sensing is the most broadly utilized spectrum sensing strategy.
Besides, it's a lot of generic as receivers doesn't would like any
information on the primary user's signals, channel data, of even the
sort of modulation. This paper puts forth the execution of energy
detection sensing for AM (Amplitude Modulated) signal at 710 KHz,
FM (Frequency Modulated) signal at 103.45 MHz (local station
frequency), Wi-Fi signal at 2.4 GHz and WiMAX signals at 6 GHz.
The OFDM/OFDMA based WiMAX physical layer with
convolutional channel coding is actualized utilizing USRP N210
(Universal Software Radio Peripheral) and GNU Radio based
Software Defined Radio (SDR). Test outcomes demonstrated the
BER (Bit Error Rate) augmentation with channel noise and BER
execution is dissected for different Eb/N0 (the energy per bit to noise
power spectral density ratio) values.
Abstract: This paper presents general results on the Java source
code snippet detection problem. We propose the tool which uses
graph and subgraph isomorphism detection. A number of solutions
for all of these tasks have been proposed in the literature. However,
although that all these solutions are really fast, they compare just the
constant static trees. Our solution offers to enter an input sample
dynamically with the Scripthon language while preserving an
acceptable speed. We used several optimizations to achieve very low
number of comparisons during the matching algorithm.
Abstract: This paper deals with the issue of biomass and sorted
municipal waste gasification and cogeneration using hot-air turbo-set.
It brings description of designed pilot plant with electrical output 80
kWe. The generated gas is burned in secondary combustion chamber
located beyond the gas generator. Flue gas flows through the heat
exchanger where the compressed air is heated and consequently
brought to a micro turbine. Except description, this paper brings our
basic experiences from operating of pilot plant (operating parameters,
contributions, problems during operating, etc.). The principal
advantage of the given cycle is the fact that there is no contact
between the generated gas and the turbine. So there is no need for
costly and complicated gas cleaning which is the main source of
operating problems in direct use in combustion engines because the
content of impurities in the gas causes operation problems to the units
due to clogging and tarring of working surfaces of engines and
turbines, which may lead as far as serious damage to the equipment
under operation. Another merit is the compact container package
making installation of the facility easier or making it relatively more
mobile. We imagine, this solution of cogeneration from biomass or
waste can be suitable for small industrial or communal applications,
for low output cogeneration.
Abstract: This research is aimed to develop the online-class
scheduling management system and improve as a complex problem
solution, this must take into consideration in various conditions and
factors. In addition to the number of courses, the number of students
and a timetable to study, the physical characteristics of each class
room and regulations used in the class scheduling must also be taken
into consideration. This system is developed to assist management in
the class scheduling for convenience and efficiency. It can provide
several instructors to schedule simultaneously. Both lecturers and
students can check and publish a timetable and other documents
associated with the system online immediately. It is developed in a
web-based application. PHP is used as a developing tool. The
database management system was MySQL. The tool that is used for
efficiency testing of the system is questionnaire. The system was
evaluated by using a Black-Box testing. The sample was composed
of 2 groups: 5 experts and 100 general users. The average and the
standard deviation of results from the experts were 3.50 and 0.67.
The average and the standard deviation of results from the general
users were 3.54 and 0.54. In summary, the results from the research
indicated that the satisfaction of users were in a good level.
Therefore, this system could be implemented in an actual workplace
and satisfy the users’ requirement effectively.
Abstract: This paper explores competencies that managers of
small firms in Ghana use to enhance operational flexibility towards
the attainment of higher productivity. This is because the requisite
competence required of such managers to be effective performers
continues to be a challenge. Data was collected from managers of
three hundred small firms using a standardized self-completion
questionnaire and analyzed using the Amos-based structural equation
model approach. Findings from factor and confirmatory factor
analyses showed that the only competence exhibited by managers
toward effective performance is realistic practices evident at the
workplace. It is concluded that a manager’s self-confidence and
involvement in areas that he/she is good at, and his/her possession of
skills that enables performance at high capacity are indications of the
manger’s effectiveness. The study outcome provides a knowledge
base helpful to policy-makers, especially in Ghana, in determining
the requisite managerial competences required by small firm
managers for effective performance.
Abstract: Over the past era, there have been a lot of efforts and
studies are carried out in growing proficient tools for performing
various tasks in big data. Recently big data have gotten a lot of
publicity for their good reasons. Due to the large and complex
collection of datasets it is difficult to process on traditional data
processing applications. This concern turns to be further mandatory
for producing various tools in big data. Moreover, the main aim of
big data analytics is to utilize the advanced analytic techniques
besides very huge, different datasets which contain diverse sizes from
terabytes to zettabytes and diverse types such as structured or
unstructured and batch or streaming. Big data is useful for data sets
where their size or type is away from the capability of traditional
relational databases for capturing, managing and processing the data
with low-latency. Thus the out coming challenges tend to the
occurrence of powerful big data tools. In this survey, a various
collection of big data tools are illustrated and also compared with the
salient features.
Abstract: The study area is Zaria, located in the basement
complex of northern Nigeria. The rock type forming the major part of
the Zaria batholith is granite. This research work was carried out to
compare the responses of seismic refraction tomography and
resistivity tomography in the same geologic environment and under
the same conditions. Hence, the choice of the site that has a visible
granitic outcrop that extends across a narrow stream channel and is
flanked by unconsolidated overburden, a neutral profile that was
covered by plain overburden and a site with thick lateritic cover
became necessary. The results of the seismic and resistivity
tomography models reveals that seismic velocity and resistivity does
not always simultaneously increase with depth, but their responses in
any geologic environment are determined by changes in the
mechanical and chemical content of the rock types rather than depth.
Abstract: In the 13th Malaysia’s General Elections held in 2013,
it was observed that large numbers of urban constituencies saw
strongly decisive young voters (between 21-39 age group) determine
the outcome in their favour. Also, the Elections Commission had
approximated that 70% of some 4.2 million unregistered voters at the
time were citizens aged between 21 and 40 years old. If they are not
already considered an important form of political leverage, 450,000
young Malaysians turn 21 years old each year. Further compounding
this fact were the 2.4 million new voters registered in 2012, which at
the time constituted almost 30% of the entire voting population. This
article discusses the importance of issues for the youth, with
reference to the university students in Malaysia in their decision
making on polling day.
Abstract: Anultra-low power capacitor less low-dropout voltage
regulator with improved transient response using gain enhanced feed
forward path compensation is presented in this paper. It is based on a
cascade of a voltage amplifier and a transconductor stage in the feed
forward path with regular error amplifier to form a composite gainenhanced
feed forward stage. It broadens the gain bandwidth and thus
improves the transient response without substantial increase in power
consumption. The proposed LDO, designed for a maximum output
current of 100 mA in UMC 180 nm, requires a quiescent current of
69 )A. An undershot of 153.79mV for a load current changes from
0mA to 100mA and an overshoot of 196.24mV for current change of
100mA to 0mA. The settling time is approximately 1.1 )s for the
output voltage undershooting case. The load regulation is of 2.77
)V/mA at load current of 100mA. Reference voltage is generated by
using an accurate band gap reference circuit of 0.8V.The costly
features of SOC such as total chip area and power consumption is
drastically reduced by the use of only a total compensation
capacitance of 6pF while consuming power consumption of 0.096
mW.
Abstract: Composite materials have important assets compared
to traditional materials. They bring many functional advantages:
lightness, mechanical resistance and chemical, etc. In the present
study we examine the effect of a circular central notch and a precrack
on the tensile fracture of two woven composite materials. The tensile
tests were applied to a standardized specimen, notched and a
precarcked (orientation of the crack 0°, 45° and 90°). These tensile
tests were elaborated according to an experimental planning design of
the type 23.31 requiring 24 experiments with three repetitions. By the
analysis of regression, we obtained a mathematical model describing
the maximum load according to the influential parameters (hole
diameter, precrack length, angle of a precrack orientation). The
specimens precracked at 90° have a better behavior than those having
a precrack at 45° and still better than those having of the precracks
oriented at 0°. In addition the maximum load is inversely
proportional to the notch size.
Abstract: Frequent pattern mining is the process of finding a
pattern (a set of items, subsequences, substructures, etc.) that occurs
frequently in a data set. It was proposed in the context of frequent
itemsets and association rule mining. Frequent pattern mining is used
to find inherent regularities in data. What products were often
purchased together? Its applications include basket data analysis,
cross-marketing, catalog design, sale campaign analysis, Web log
(click stream) analysis, and DNA sequence analysis. However, one of
the bottlenecks of frequent itemset mining is that as the data increase
the amount of time and resources required to mining the data
increases at an exponential rate. In this investigation a new algorithm
is proposed which can be uses as a pre-processor for frequent itemset
mining. FASTER (FeAture SelecTion using Entropy and Rough sets)
is a hybrid pre-processor algorithm which utilizes entropy and roughsets
to carry out record reduction and feature (attribute) selection
respectively. FASTER for frequent itemset mining can produce a
speed up of 3.1 times when compared to original algorithm while
maintaining an accuracy of 71%.
Abstract: The paper discusses economic policy of Georgia
aiming to increase national competitiveness as well as the tools and
means which will help to improve the competitiveness of the country.
The sectors of the economy, in which the country can achieve the
competitive advantage, are studied. It is noted that the country’s
economic policy plays an important role in obtaining and maintaining
the competitive advantage - authority should take measures to ensure
high level of education; scientific and research activities should be
funded by the state; foreign direct investments should be attracted
mainly in science-intensive industries; adaptation with the latest
scientific achievements of the modern world and deepening of
scientific and technical cooperation. Stable business environment and
export oriented strategy is the basis for the country’s economic
growth.
As the outcome of the research, the paper suggests the strategy for
improving competitiveness in Georgia; recommendations are
provided based on relevant conclusions.
Abstract: Sudoku is a logic-based combinatorial puzzle game
which people in different ages enjoy playing it. The challenging and
addictive nature of this game has made it a ubiquitous game. Most
magazines, newspapers, puzzle books, etc. publish lots of Sudoku
puzzles every day. These puzzles often come in different levels of
difficulty so that all people, from beginner to expert, can play the
game and enjoy it. Generating puzzles with different levels of
difficulty is a major concern of Sudoku designers. There are several
works in the literature which propose ways of generating puzzles
having a desirable level of difficulty. In this paper, we propose a
method based on constraint satisfaction problems to evaluate the
difficulty of the Sudoku puzzles. Then we propose a hill climbing
method to generate puzzles with different levels of difficulty.
Whereas other methods are usually capable of generating puzzles
with only few number of difficulty levels, our method can be used to
generate puzzles with arbitrary number of different difficulty levels.
We test our method by generating puzzles with different levels of
difficulty and having a group of 15 people solve all the puzzles and
recording the time they spend for each puzzle.
Abstract: From an organizational perspective, leaders are a
variation of the same talent pool in that they all score a larger than
average value on the bell curve that maps leadership behaviors and
characteristics, namely competence, vision, communication,
confidence, cultural sensibility, stewardship, empowerment,
authenticity, reinforcement, and creativity. The question that remains
unanswered and essentially unresolved is how to explain the irony
that leaders are so much alike yet their organizations diverge so
noticeably in their ability to innovate. Leadership intersects with
innovation at the point where human interactions get exceedingly
complex and where certain paradoxical forces cohabit: conflict with
conciliation, sovereignty with interdependence, and imagination with
realism. Rather than accepting that leadership is without context, we
argue that leaders are specialists of their domain and that those
effective at leading for innovation are distinct within the broader pool
of leaders. Keeping in view the extensive literature on leadership and
innovation, we carried out a quantitative study with data collected
over a five-year period involving 240 participants from across five
dissimilar companies based in the United States. We found that while
innovation and leadership are, in general, strongly interrelated (r =
.89, p = 0.0), there are five qualities that set leaders apart on
innovation. These qualities include a large radius of trust, a restless
curiosity with a low need for acceptance, an honest sense of self and
other, a sense for knowledge and creativity as the yin and yang of
innovation, and an ability to use multiple senses in the engagement
with followers. When these particular behaviors and characteristics
are present in leaders, organizations out-innovate their rivals by a
margin of 29.3 per cent to gain an unassailable edge in a business
environment that is regularly disruptive. A strategic outcome of this
study is a psychometric scale named iLeadership, proposed with the
underlying evidence, limitations, and potential for leadership and
innovation in organizations.c
Abstract: This paper presents a new meta-heuristic bio-inspired
optimization algorithm which is called Cuttlefish Algorithm (CFA).
The algorithm mimics the mechanism of color changing behavior of
the cuttlefish to solve numerical global optimization problems. The
colors and patterns of the cuttlefish are produced by reflected light
from three different layers of cells. The proposed algorithm considers
mainly two processes: reflection and visibility. Reflection process
simulates light reflection mechanism used by these layers, while
visibility process simulates visibility of matching patterns of the
cuttlefish. To show the effectiveness of the algorithm, it is tested with
some other popular bio-inspired optimization algorithms such as
Genetic Algorithms (GA), Particle Swarm Optimization (PSO) and
Bees Algorithm (BA) that have been previously proposed in the
literature. Simulations and obtained results indicate that the proposed
CFA is superior when compared with these algorithms.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.