Abstract: Small signal stability causes small perturbations in the
generator that can cause instability in the power network. It is
generally known that small signal stability are directly related to the
generator and load properties. This paper examines the effects of
generator input variations on power system oscillations for a small
signal stability study. Eigenvaules and eigenvectors are used to
examine the stability of the power system. The dynamic power
system's mathematical model is constructed and thus calculated using
load flow and small signal stability toolbox on MATLAB. The power
system model is based on a 3-machine 9-bus system that was
modified to suit this study. In this paper, Participation Factors are a
means to gauge the effects of variation in generation with other
parameters on the network are also incorporated.
Abstract: The design of high-rise building is more often dictated
by its serviceability rather than strength. Structural Engineers are
always striving to overcome challenge of controlling lateral
deflection and storey drifts as well as self weight of structure
imposed on foundation.
One of the most effective techniques is the use of outrigger and
belt truss system in Composite structures that can astutely solve the
above two issues in High-rise constructions.
This paper investigates deflection control by effective utilisation
of belt truss and outrigger system on a 60-storey composite building
subjected to wind loads. A three dimensional Finite Element Analysis
is performed with one, two and three outrigger levels. The reductions
in lateral deflection are 34%, 42% and 51% respectively as compared
to a model without any outrigger system. There is an appreciable
decline in the storey drifts with the introduction of these stiffer
arrangements.
Abstract: In the current Grid environment, efficient workload
management presents a significant challenge, for which there are
exorbitant de facto standards encompassing resource discovery,
brokerage, and data transfer, among others. In addition, the real-time
resource status, essential for an optimal resource allocation strategy,
is often not readily accessible. To address these issues and provide a
cleaner abstraction of the Grid with the potential of generalizing into
arbitrary resource-sharing environment, this paper proposes a new
Condor-based pilot mechanism applied in the PanDA architecture,
PanDA-PF WMS, with the goal of providing a more generic yet
efficient resource allocating strategy. In this architecture, the PanDA
server primarily acts as a repository of user jobs, responding to pilot
requests from distributed, remote resources. Scheduling decisions are
subsequently made according to the real-time resource information
reported by pilots. Pilot Factory is a Condor-inspired solution for a
scalable pilot dissemination and effectively functions as a resource
provisioning mechanism through which the user-job server, PanDA,
reaches out to the candidate resources only on demand.
Abstract: Fatigue behaviors of Lead Zirconate Titanate (PZT)
ceramics under different amplitude of bipolar electrical loads have
been investigated. Fatigue behavior is represented by the change of
hysteresis loops and remnant polarization. Three levels of electrical
load amplitudes (1.00, 1.25 and 1.50 kV /mm) were applied in this
experimental. It was found that the remnant polarization decreased
significantly with the number of loading cycles. The degree of fatigue
degradation depends on the amplitude of electric field. The higher
amplitude exhibits the greater fatigue degradation.
Abstract: Fuzzy Load forecasting plays a paramount role in the operation and management of power systems. Accurate estimation of future power demands for various lead times facilitates the task of generating power reliably and economically. The forecasting of future loads for a relatively large lead time (months to few years) is studied here (long term load forecasting). Among the various techniques used in forecasting load, artificial intelligence techniques provide greater accuracy to the forecasts as compared to conventional techniques. Fuzzy Logic, a very robust artificial intelligent technique, is described in this paper to forecast load on long term basis. The paper gives a general algorithm to forecast long term load. The algorithm is an Extension of Short term load forecasting method to Long term load forecasting and concentrates not only on the forecast values of load but also on the errors incorporated into the forecast. Hence, by correcting the errors in the forecast, forecasts with very high accuracy have been achieved. The algorithm, in the paper, is demonstrated with the help of data collected for residential sector (LT2 (a) type load: Domestic consumers). Load, is determined for three consecutive years (from April-06 to March-09) in order to demonstrate the efficiency of the algorithm and to forecast for the next two years (from April-09 to March-11).
Abstract: Data Warehouses (DWs) are repositories which contain the unified history of an enterprise for decision support. The data must be Extracted from information sources, Transformed and integrated to be Loaded (ETL) into the DW, using ETL tools. These tools focus on data movement, where the models are only used as a means to this aim. Under a conceptual viewpoint, the authors want to innovate the ETL process in two ways: 1) to make clear compatibility between models in a declarative fashion, using correspondence assertions and 2) to identify the instances of different sources that represent the same entity in the real-world. This paper presents the overview of the proposed framework to model the ETL process, which is based on the use of a reference model and perspective schemata. This approach provides the designer with a better understanding of the semantic associated with the ETL process.
Abstract: Aim of this work was to compare the efficacy of two
loading methods of proteins onto polymeric nanocarriers: adsorption
and encapsulation methods. Preliminary studies of protein loading
were done using Bovine Serum Albumin (BSA) as model protein.
Nanocarriers were prepared starting from polylactic co-glycolic acid
(PLGA) polymer; production methods used are two different variants
of emulsion evaporation method. Nanoparticles obtained were
analyzed in terms of dimensions by Dynamic Light Scattering and
Loading Efficiency of BSA by Bradford Assay. Loaded
nanoparticles were then submitted to in-vitro protein dissolution test
in order to study the effect of the delivery system on the release rate
of the protein.
Abstract: The aim of this study was to evaluate the sensitivity
of a range of EEG indices to time-on-task effects and to a workload
manipulation (cueing), during performance of a resource-limited
vigilance task. Effects of task period and cueing on performance and
subjective state response were consistent with previous vigilance
studies and with resource theory. Two EEG indices – the Task Load
Index (TLI) and global lower frequency (LF) alpha power – showed
effects of task period and cueing similar to those seen with correct
detections. Across four successive task periods, the TLI declined and
LF alpha power increased. Cueing increased TLI and decreased LF
alpha. Other indices – the Engagement Index (EI), frontal theta and
upper frequency (UF) alpha failed to show these effects. However, EI
and frontal theta were sensitive to interactive effects of task period
and cueing, which may correspond to a stronger anxiety response to
the uncued task.
Abstract: Integral Abutment Bridges (IAB) are defined as
simple or multiple span bridges in which the bridge deck is cast
monolithically with the abutment walls. This kind of bridges are
becoming very popular due to different aspects such as good
response under seismic loading, low initial costs, elimination of
bearings, and less maintenance. However the main issue related to
the analysis of this type of structures is dealing with soil-structure
interaction of the abutment walls and the supporting piles. Various
soil constitutive models have been used in studies of soil-structure
interaction in this kind of structures by researchers. This paper is an
effort to review the implementation of various finite elements model
which explicitly incorporates the nonlinear soil and linear structural
response considering various soil constitutive models and finite
element mesh.
Abstract: This paper reports a new and accurate method for load-flow solution of radial distribution networks with minimum data preparation. The node and branch numbering need not to be sequential like other available methods. The proposed method does not need sending-node, receiving-node and branch numbers if these are sequential. The proposed method uses the simple equation to compute the voltage magnitude and has the capability to handle composite load modelling. The proposed method uses the set of nodes of feeder, lateral(s) and sub lateral(s). The effectiveness of the proposed method is compared with other methods using two examples. The detailed load-flow results for different kind of load-modellings are also presented.
Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: The effect of the discontinuity of the rail ends and the
presence of lower modulus insulation material at the gap to the
variations of stresses in the insulated rail joint (IRJ) is presented. A
three-dimensional wheel – rail contact model in the finite element
framework is used for the analysis. It is shown that the maximum stress
occurs in the subsurface of the railhead when the wheel contact occurs
far away from the rail end and migrates to the railhead surface as the
wheel approaches the rail end; under this condition, the interface
between the rail ends and the insulation material has suffered
significantly increased levels of stress concentration. The ratio of the
elastic modulus of the railhead and insulation material is found to alter
the levels of stress concentration. Numerical result indicates that a
higher elastic modulus insulating material can reduce the stress
concentration in the railhead but will generate higher stresses in the
insulation material, leading to earlier failure of the insulation material
Abstract: This paper study the behavior of the solution at the crack edges for an elliptical crack with developing cusps, Ω in the plane elasticity subjected to shear loading. The problem of finding the resulting shear stress can be formulated as a hypersingular integral equation over Ω and it is then transformed into a similar equation over a circular region, D, using conformal mapping. An appropriate collocation points are chosen on the region D to reduce the hypersingular integral equation into a system of linear equations with (2N+1)(N+1) unknown coefficients, which will later be used in the determination of shear stress intensity factors and maximum shear stress intensity. Numerical solution for the considered problem are compared with the existing asymptotic solution, and displayed graphically. Our results give a very good agreement to the existing asymptotic solutions.
Abstract: In this study, the transesterification of palm oil with methanol for biodiesel production was studied by using CaO–ZnO as a heterogeneous base catalyst prepared by incipient-wetness impregnation (IWI) and co-precipitation (CP) methods. The reaction parameters considered were molar ratio of methanol to oil, amount of catalyst, reaction temperature, and reaction time. The optimum conditions–15:1 molar ratio of methanol to oil, a catalyst amount of 6 wt%, reaction temperature of 60 °C, and reaction time of 8 h–were observed. The effects of Ca loading, calcination temperature, and catalyst preparation on the catalytic performance were studied. The fresh and spent catalysts were characterized by several techniques, including XRD, TPR, and XRF.
Abstract: The iron loss is a source of detuning in vector controlled
induction motor drives if the classical rotor vector controller is used for
decoupling. In fact, the field orientation will not be satisfied and the
output torque will not truck the reference torque mostly used by Loss
Model Controllers (LMCs). In addition, this component of loss, among
others, may be excessive if the vector controlled induction motor is
driving light loads. In this paper, the series iron loss model is used to
develop a vector controller immune to iron loss effect and then an LMC
to minimize the total power loss using the torque generated by the speed
controller.
Abstract: Factoring Boolean functions is one of the basic operations in algorithmic logic synthesis. A novel algebraic factorization heuristic for single-output combinatorial logic functions is presented in this paper and is developed based on the set theory paradigm. The impact of factoring is analyzed mainly from a low power design perspective for standard cell based digital designs in this paper. The physical implementation of a number of MCNC/IWLS combinational benchmark functions and sub-functions are compared before and after factoring, based on a simple technology mapping procedure utilizing only standard gate primitives (readily available as standard cells in a technology library) and not cells corresponding to optimized complex logic. The power results were obtained at the gate-level by means of an industry-standard power analysis tool from Synopsys, targeting a 130nm (0.13μm) UMC CMOS library, for the typical case. The wire-loads were inserted automatically and the simulations were performed with maximum input activity. The gate-level simulations demonstrate the advantage of the proposed factoring technique in comparison with other existing methods from a low power perspective, for arbitrary examples. Though the benchmarks experimentation reports mixed results, the mean savings in total power and dynamic power for the factored solution over a non-factored solution were 6.11% and 5.85% respectively. In terms of leakage power, the average savings for the factored forms was significant to the tune of 23.48%. The factored solution is expected to better its non-factored counterpart in terms of the power-delay product as it is well-known that factoring, in general, yields a delay-efficient multi-level solution.
Abstract: 98% of the energy needed in Taiwan has been
imported. The prices of petroleum and electricity have been
increasing. In addition, facility capacity, amount of electricity
generation, amount of electricity consumption and number of Taiwan
Power Company customers have continued to increase. For these
reasons energy conservation has become an important topic. In the
past linear regression was used to establish the power consumption
models for chillers. In this study, grey prediction is used to evaluate
the power consumption of a chiller so as to lower the total power
consumption at peak-load (so that the relevant power providers do not
need to keep on increasing their power generation capacity and facility
capacity).
In grey prediction, only several numerical values (at least four
numerical values) are needed to establish the power consumption
models for chillers. If PLR, the temperatures of supply chilled-water
and return chilled-water, and the temperatures of supply cooling-water
and return cooling-water are taken into consideration, quite accurate
results (with the accuracy close to 99% for short-term predictions)
may be obtained. Through such methods, we can predict whether the
power consumption at peak-load will exceed the contract power
capacity signed by the corresponding entity and Taiwan Power
Company. If the power consumption at peak-load exceeds the power
demand, the temperature of the supply chilled-water may be adjusted
so as to reduce the PLR and hence lower the power consumption.
Abstract: With the rapid usage of portable devices mobility in
IP networks becomes more important issue in the recent years. IETF
standardized Mobile IP that works in Network Layer, which involves
tunneling of IP packets from HA to Foreign Agent. Mobile IP suffers
many problems of Triangular Routing, conflict with private
addressing scheme, increase in load in HA, need of permanent home
IP address, tunneling itself, and so on. In this paper, we proposed
mobility management in Application Layer protocol SIP and show
some comparative analysis between Mobile IP and SIP in context of
mobility.
Abstract: SeqWord Gene Island Sniffer, a new program for
the identification of mobile genetic elements in sequences of bacterial chromosomes is presented. This program is based on the
analysis of oligonucleotide usage variations in DNA sequences. 3,518 mobile genetic elements were identified in 637 bacterial
genomes and further analyzed by sequence similarity and the
functionality of encoded proteins. The results of this study are stored in an open database http://anjie.bi.up.ac.za/geidb/geidbhome.
php). The developed computer program and the database provide the information valuable for further investigation of the
distribution of mobile genetic elements and virulence factors among bacteria. The program is available for download at www.bi.up.ac.za/SeqWord/sniffer/index.html.
Abstract: In this paper, a novel scheme is proposed for ownership identification and authentication using color images by deploying Cryptography and Digital Watermarking as underlaying technologies. The former is used to compute the contents based hash and the latter to embed the watermark. The host image that will claim to be the rightful owner is first transformed from RGB to YST color space exclusively designed for watermarking based applications. Geometrically YS ÔèÑ T and T channel corresponds to the chrominance component of color image, therefore suitable for embedding the watermark. The T channel is divided into 4×4 nonoverlapping blocks. The size of block is important for enhanced localization, security and low computation. Each block along with ownership information is then deployed by SHA160, a one way hash function to compute the content based hash, which is always unique and resistant against birthday attack instead of using MD5 that may raise the condition i.e. H(m)=H(m'). The watermark payload varies from block to block and computed by the variance factorα . The quality of watermarked images is quite high both subjectively and objectively. Our scheme is blind, computationally fast and exactly locates the tampered region.