Abstract: Multidrug resistant organisms have been taunting the
medical world for the last few decades. Even with new antibiotics
developed, resistant strains have emerged soon after. With the
advancement of nanotechnology, we investigated colloidal silver
nanoparticles for its antimicrobial activity against Pseudomonas
aeruginosa. This organism is a multidrug resistant which contributes
to the high morbidity and mortality in immunocompromised patients.
Five multidrug resistant strains were used in this study. The
antimicrobial effect was studied using the disc diffusion and broth
dilution techniques. An inhibition zone of 11 mm was observed with
10 μg dose of the nanoparticles. The nanoparticles exhibited MIC of
50 μg/ml when added at the lag phase and the subinhibitory
concentration was measured as 100 μg/ml. The MIC50 value showed
to be 15 μg/ml. This study suggests that silver nanoparticles can be
further developed as an antimicrobial agent, hence decreasing the
burden of the multidrug resistance phenomena.
Abstract: This paper addresses the problem of peak-to-average
power ratio (PAPR) in orthogonal frequency division multiplexing
(OFDM) systems. It also introduces a new PAPR reduction technique
based on adaptive square-rooting (SQRT) companding process. The
SQRT process of the proposed technique changes the statistical
characteristics of the OFDM output signals from Rayleigh
distribution to Gaussian-like distribution. This change in statistical
distribution results changes of both the peak and average power
values of OFDM signals, and consequently reduces significantly the
PAPR. For the 64QAM OFDM system using 512 subcarriers, up to 6
dB reduction in PAPR was achieved by square-rooting technique
with fixed degradation in bit error rate (BER) equal to 3 dB.
However, the PAPR is reduced at the expense of only -15 dB out-ofband
spectral shoulder re-growth below the in-band signal level. The
proposed adaptive SQRT technique is superior in terms of BER
performance than the original, non-adaptive, square-rooting
technique when the required reduction in PAPR is no more than 5
dB. Also, it provides fixed amount of PAPR reduction in which it is
not available in the original SQRT technique.
Abstract: The paper presents coupled electromagnetic and
thermal field analysis of busbar system (of rectangular cross-section
geometry) submitted to short circuit conditions. The laboratory model
was validated against both analytical solution and experimental
observations. The considered problem required the computation of
the detailed distribution of the power losses and the heat transfer
modes. In this electromagnetic and thermal analysis, different
definitions of electric busbar heating were considered and compared.
The busbar system is a three phase one and consists of aluminum,
painted aluminum and copper busbar. The solution to the coupled
field problem is obtained using the finite element method and the
QuickField™ program. Experiments have been carried out using two
different approaches and compared with computed results.
Abstract: This paper is to present context-aware sensor grid
framework for agriculture and its design challenges. Use of sensor
networks in the domain of agriculture is not new. However, due to
the unavailability of any common framework, solutions that are
developed in this domain are location, environment and problem
dependent. Keeping the need of common framework for agriculture,
Context-Aware Sensor Grid Framework is proposed. It will be
helpful in developing solutions for majority of the problems related
to irrigation, pesticides spray, use of fertilizers, regular monitoring of
plot and yield etc. due to the capability of adjusting according to
location and environment. The proposed framework is composed of
three layer architecture including context-aware application layer,
grid middleware layer and sensor network layer.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: In this paper, we present a novel objective nonreference
performance assessment algorithm for image fusion. It takes
into account local measurements to estimate how well the important
information in the source images is represented by the fused image.
The metric is based on the Universal Image Quality Index and uses
the similarity between blocks of pixels in the input images and the
fused image as the weighting factors for the metrics. Experimental
results confirm that the values of the proposed metrics correlate well
with the subjective quality of the fused images, giving a significant
improvement over standard measures based on mean squared error
and mutual information.
Abstract: Sensors possess several properties of physical
measures. Whether devices that convert a sensed signal into an
electrical signal, chemical sensors and biosensors, thus all these
sensors can be considered as an interface between the physical and
electrical equipment. The problem is the analysis of the multitudes of
saved settings as input variables. However, they do not all have the
same level of influence on the outputs. In order to identify the most
sensitive parameters, those that can guide users in gathering
information on the ground and in the process of model calibration
and sensitivity analysis for the effect of each change made.
Mathematical models used for processing become very complex.
In this paper a fuzzy rule-based system is proposed as a solution
for this problem. The system collects the available signals
information from sensors. Moreover, the system allows the study of
the influence of the various factors that take part in the decision
system. Since its inception fuzzy set theory has been regarded as a
formalism suitable to deal with the imprecision intrinsic to many
problems. At the same time, fuzzy sets allow to use symbolic models.
In this study an example was applied for resolving variety of
physiological parameters that define human health state. The
application system was done for medical diagnosis help. The inputs
are the signals expressed the cardiovascular system parameters, blood
pressure, Respiratory system paramsystem was done, it will be able
to predict the state of patient according any input values.
Abstract: It is shown that the relationship of tick-borne
encephalitis virus with the human body comes in two ways, the
development of acute infection with the outcome in convalescence
and long stay by the virus in the body, its persistence in the nervous
tissue with periodic reactivation and prolonged circulating
immunoglobulin M. In spite of the fact that tick-borne encephalitis
virus has a tropism for nerve tissue, involvement in the process of
blood cells is an integral component of the infection. Comprehensive
study of the relation of factors of innate and adaptive immunity in the
tick-borne encephalitis providing insight into the features of chronic
disease.
Abstract: The blood ducts must be occluded to avoid loss of
blood from vessels in laparoscopic surgeries. This paper presents a
locking mechanism to be used in a ligation laparoscopic procedure
(LigLAP I), as an alternative solution for a stapling procedure.
Currently, stapling devices are being used to occlude vessels. Using
these devices may result in some problems, including injury of bile
duct, taking up a great deal of space behind the vessel, and bile leak.
In this new procedure, a two-layer suture occludes a vessel. A
locking mechanism is also required to hold the suture. Since there is
a limited space at the device tip, a Shape Memory Alloy (SMA)
actuator is used in this mechanism. Suitability for cleanroom
applications, small size, and silent performance are among the
advantages of SMA actuators in biomedical applications. An
experimental study is conducted to examine the function of the
locking mechanism. To set up the experiment, a prototype of a
locking mechanism is built using nitinol, which is a nickel-titanium
shape memory alloy. The locking mechanism successfully locks a
polymer suture for all runs of the experiment. In addition, the effects
of various surface materials on the applied pulling forces are studied.
Various materials are mounted at the mechanism tip to compare the
maximum pulling forces applied to the suture for each material. The
results show that the various surface materials on the device tip
provide large differences in the applied pulling forces.
Abstract: Many organisations are nowadays interested to adopt
lean manufacturing strategy that would enable them to compete in
this competitive globalisation market. In this respect, it is necessary
to assess the implementation of lean manufacturing in different
organisations so that the important best practices can be identified.
This paper describes the development of key areas which will be
used to assess the adoption and implementation of lean
manufacturing practices. There are some key areas developed to
evaluate and reduce the most optimal projects so as to enhance their
production efficiency and increase the purpose of the economic
benefits of the manufacturing unit.
Lean manufacturing is becoming lean enterprise by treating its
customers and suppliers as partners. This gives the extra edge in
today-s cost and time competitive markets. The organisation is
becoming strong in all the conventional competition points. They are
Price, Quality and Delivery. Lean enterprise owners can deliver high
quality products quickly, with low price.
Abstract: Silicon is a beneficial element for plant growth. It
helps plants to overcome multiple stresses, alleviates metal toxicity
and improves nutrient imbalance. Field experiment was conducted as
split-split plot arranged in a randomized complete block design with
four replications. Irrigation system include continues flooding and
deficit as main plots and nitrogen rates N0, N46, N92, and N138 kg/ha
as sub plots and silicon rates Si0 & Si500 kg/ha as sub-subplots.
Results indicate that grain yield had not significant difference
between irrigation systems. Flooding irrigation had higher biological
yield than deficit irrigation whereas, no significant difference in grain
and straw yield. Nitrogen application increased grain, biological and
straw yield. Silicon application increased grain, biological and straw
yield but, decreased harvest index. Flooding irrigation had higher
number of total tillers / hill than deficit irrigation, but deficit
irrigation had higher number of fertile tillers / hill than flooding
irrigation. Silicon increased number of filled spikelet and decreased
blank spikelet. With high nitrogen application decreased 1000-grain
weight. It can be concluded that if the nitrogen application was high
and water supplied was available we could have silicon application
until increase grain yield.
Abstract: International literature emphasizes on the concern regarding the phenomenon of aggression in hospital. This paper focuses on the reality of aggressive interactions reigning within an emergency triage involving three chaps of protagonists: the professionals, the patients and their carers. The data collection was made from a grid of observation, in which the various variables exposed in the literature were integrated. They observations took place around the clock, for three weeks, at the rate of one week a month. In this research 331 aggressive interactions have been listed and analyzed by means of the software SPSS. This research is one of the very few continuous observation surveys in the literature. It shows the various human factors at play in the emergence of aggressive interaction. The data may be used both for taking steps in primary prevention, thanks to the analysis of interaction modes, and in secondary prevention by integrating the useful results in situational prevention.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: The choice of finite element to use in order to predict
nonlinear static or dynamic response of complex structures becomes
an important factor. Then, the main goal of this research work is to
focus a study on the effect of the in-plane rotational degrees of
freedom in linear and geometrically non linear static and dynamic
analysis of thin shell structures by flat shell finite elements. In this
purpose: First, simple triangular and quadrilateral flat shell finite
elements are implemented in an incremental formulation based on the
updated lagrangian corotational description for geometrically
nonlinear analysis. The triangular element is a combination of DKT
and CST elements, while the quadrilateral is a combination of DKQ
and the bilinear quadrilateral membrane element. In both elements,
the sixth degree of freedom is handled via introducing fictitious
stiffness. Secondly, in the same code, the sixth degrees of freedom in
these elements is handled differently where the in-plane rotational
d.o.f is considered as an effective d.o.f in the in-plane filed
interpolation. Our goal is to compare resulting shell elements. Third,
the analysis is enlarged to dynamic linear analysis by direct
integration using Newmark-s implicit method. Finally, the linear
dynamic analysis is extended to geometrically nonlinear dynamic
analysis where Newmark-s method is used to integrate equations of
motion and the Newton-Raphson method is employed for iterating
within each time step increment until equilibrium is achieved. The
obtained results demonstrate the effectiveness and robustness of the
interpolation of the in-plane rotational d.o.f. and present deficiencies
of using fictitious stiffness in dynamic linear and nonlinear analysis.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: The modified Claus process is the major technology
for the recovery of elemental sulfur from hydrogen sulfide. The
chemical reactions that can occur in the reaction furnace are
numerous and many byproducts such as carbon disulfide and carbon
carbonyl sulfide are produced. These compounds can often contribute
from 20 to 50% of the pollutants and therefore, should be hydrolyzed
in the catalytic converter. The inlet temperature of the first catalytic
reactor should be maintained over than 250 °C, to hydrolyze COS
and CS2. In this paper, the various configurations for the first
converter reheating of sulfur recovery unit are investigated. As a
result, the performance of each method is presented for a typical
clause unit. The results show that the hot gas method seems to be
better than the other methods.
Abstract: In this paper we used data mining techniques to
identify outlier patients who are using large amount of drugs over a
long period of time. Any healthcare or health insurance system
should deal with the quantities of drugs utilized by chronic diseases
patients. In Kingdom of Bahrain, about 20% of health budget is spent
on medications. For the managers of healthcare systems, there is no
enough information about the ways of drug utilization by chronic
diseases patients, is there any misuse or is there outliers patients. In
this work, which has been done in cooperation with information
department in the Bahrain Defence Force hospital; we select the data
for Cardiac patients in the period starting from 1/1/2008 to
December 31/12/2008 to be the data for the model in this paper. We
used three techniques for finding the drug utilization for cardiac
patients. First we applied a clustering technique, followed by
measuring of clustering validity, and finally we applied a decision
tree as classification algorithm. The clustering results is divided into
three clusters according to the drug utilization, for 1603 patients, who
received 15,806 prescriptions during this period can be partitioned
into three groups, where 23 patients (2.59%) who received 1316
prescriptions (8.32%) are classified to be outliers. The classification
algorithm shows that the use of average drug utilization and the age,
and the gender of the patient can be considered to be the main
predictive factors in the induced model.
Abstract: This paper proposes a method for speckle reduction in
medical ultrasound imaging while preserving the edges with the
added advantages of adaptive noise filtering and speed. A nonlinear
image diffusion method that incorporates local image parameter,
namely, scatterer density in addition to gradient, to weight the
nonlinear diffusion process, is proposed. The method was tested for
the isotropic case with a contrast detail phantom and varieties of
clinical ultrasound images, and then compared to linear and some
other diffusion enhancement methods. Different diffusion parameters
were tested and tuned to best reduce speckle noise and preserve
edges. The method showed superior performance measured both
quantitatively and qualitatively when incorporating scatterer density
into the diffusivity function. The proposed filter can be used as a
preprocessing step for ultrasound image enhancement before
applying automatic segmentation, automatic volumetric calculations,
or 3D ultrasound volume rendering.