Abstract: This paper describes an optimization tool-based
design strategy for a Current Mode Logic CML divide-by-2 circuit.
Representing a building block for output frequency generation in a
RFID protocol based-frequency synthesizer, the circuit was designed
to minimize the power consumption for driving of multiple loads
with unbalancing (at transceiver level). Implemented with XFAB
XC08 180 nm technology, the circuit was optimized through
MunEDA WiCkeD tool at Cadence Virtuoso Analog Design
Environment ADE.
Abstract: The chemical and physical characteristics of rainwater
harvested from a typical rooftop were progressively studied. The
samples of rainwater collected were analyzed for pH, major ion
concentrations, TDS, turbidity, conductivity. All the Physicochemical
constituents fell within the WHO guideline limits at some points as
rainfall progresses except the pH. All the components of rainwater
quality measured during the study showed higher concentrations
during the early stages of rainfall and reduce as time progresses.
There was a downward trend in terms of pH as rain progressed, with
18% of the samples recording pH below the WHO limit of 6.5-8.0. It
was observed that iron concentration was above the WHO threshold
value of 0.3 mg/l on occasions of heavy rains. The results revealed
that most of physicochemical characteristics of rainwater samples
were generally below the WHO threshold, as such, the rainwater
characteristics showed satisfactory conditions in terms of
physicochemical constituents.
Abstract: Through use of novel modern/rapid processing
techniques such as screen printing and Near-Infrared (NIR) radiative
curing, process time for the sintering of sintered nickel plaques,
applicable to alkaline nickel battery chemistries, has been drastically
reduced from in excess of 200 minutes with conventional convection
methods to below 2 minutes using NIR curing methods. Steps have
also been taken to remove the need for forming gas as a reducing
agent by implementing carbon as an in-situ reducing agent, within the
ink formulation.
Abstract: This paper investigates simple implicit force control
algorithms realizable with industrial robots. A lot of approaches
already published are difficult to implement in commercial robot
controllers, because the access to the robot joint torques is necessary
or the complete dynamic model of the manipulator is used. In
the past we already deal with explicit force control of a position
controlled robot. Well known schemes of implicit force control are
stiffness control, damping control and impedance control. Using such
algorithms the contact force cannot be set directly. It is further
the result of controller impedance, environment impedance and
the commanded robot motion/position. The relationships of these
properties are worked out in this paper in detail for the chosen
implicit approaches. They have been adapted to be implementable
on a position controlled robot. The behaviors of stiffness control
and damping control are verified by practical experiments. For this
purpose a suitable test bed was configured. Using the full mechanical
impedance within the controller structure will not be practical in the
case when the robot is in physical contact with the environment. This
fact will be verified by simulation.
Abstract: In this study, firstly democratic thoughts which
directly or indirectly affect economic development and/or the
interaction between authoritarian regimes and the economic
development and the direction and channels of this interaction were
studied and then the study tried to determine how democracy affects
economic development. It was concluded that the positive
contributions of democracy to economic development were more
determinant than the effects that were either negative or restrictive in
terms of development. When compared to autocracy, since
democracy is more successful in managing social conflicts, ensuring
political stability and preventing social disasters such as famine, it
contributes more to economic development. Democracy also
facilitates delegation of authority, provides a stable investment
environment and accelerates mobilization of resources in accordance
with economic growth/development. Democracy leads to an increase
in human capital accumulation and increases the growth rate through
reducing income inequality. It can be said that democratic regimes
are the most appropriate ones in terms of increasing economic
performance and supporting economic development through their
strong institutional structures and the assurance they will ensure in
property rights.
Abstract: Non-crimp 3D orthogonal fabric composite is one of
the textile-based composite materials that are rapidly developing
light-weight engineering materials. The present paper focuses on
geometric and micromechanical modeling of non-crimp 3D
orthogonal carbon fabric and composites reinforced with it for
aerospace applications. In this research meso-finite element (FE)
modeling employs for stress analysis in different load conditions.
Since mechanical testing of expensive textile carbon composites with
specific application isn't affordable, simulation composite in a virtual
environment is a helpful way to investigate its mechanical properties
in different conditions.
Abstract: Chitosan functionalized Fe3O4-Au core shell
nanoparticles have been prepared using a two-step wet chemical
approach using NaBH4 as reducing agent for formation of Au in
ethylene glycol. X-ray diffraction studies shows individual phases of
Fe3O4 and Au in the as prepared samples with crystallite size of 5.9
and 11.4 nm respectively. The functionalization of the core-shell
nanostructure with Chitosan has been confirmed using Fourier
transform infrared spectroscopy along with signatures of octahedral
and tetrahedral sites of Fe3O4 below 600cm-1. Mössbauer
spectroscopy shows decrease in particle-particle interaction in
presence of Au shell (72% sextet) than pure oleic coated Fe3O4
nanoparticles (88% sextet) at room temperature. At 80K, oleic acid
coated Fe3O4 shows only sextets whereas the Chitosan functionalized
Fe3O4 and Chitosan functionalized Fe3O4@Au core shell show
presence of 5 and 11% doublet, respectively.
Abstract: Many water desalination technologies have been
developed but in general they are energy intensive and have high cost
and adverse environmental impact. Recently, adsorption technology
for water desalination has been investigated showing the potential of
using low temperature waste heat (50-85oC) thus reducing energy
consumption and CO2 emissions. This work mathematically
compares the performance of an adsorption cycle that produces two
useful effects namely, fresh water and cooling using two different
adsorbents, silica-gel and an advanced zeolite material AQSOA-ZO2,
produced by Mitsubishi plastics. It was found that at low chilled
water temperatures, typically below 20oC, the AQSOA-Z02 is more
efficient than silica-gel as the cycle can produce 5.8 m3 of fresh water
per day and 50.1 Rton of cooling per tonne of AQSOA-ZO2. Above
20oC silica-gel is still better as the cycle production reaches 8.4 m3
per day and 62.4 Rton per tonne of silica-gel. These results show the
potential of using the AQSOA-Z02 at low chilled water temperature
for water desalination and cooling applications.
Abstract: Purpose: The study aimed to assess the depressant or
antidepressant effects of several Nonsteroidal Anti-Inflammatory
Drugs (NSAIDs) in mice: the selective cyclooxygenase-2 (COX-2)
inhibitor meloxicam, and the non-selective COX-1 and COX-2
inhibitors lornoxicam, sodium metamizole, and ketorolac. The
current literature data regarding such effects of these agents are
scarce.
Materials and methods: The study was carried out on NMRI mice
weighing 20-35 g, kept in a standard laboratory environment. The
study was approved by the Ethics Committee of the University of
Medicine and Pharmacy „Carol Davila”, Bucharest. The study agents
were injected intraperitoneally, 10 mL/kg body weight (bw) 1 hour
before the assessment of the locomotor activity by cage testing (n=10
mice/ group) and 2 hours before the forced swimming tests (n=15).
The study agents were dissolved in normal saline (meloxicam,
sodium metamizole), ethanol 11.8% v/v in normal saline (ketorolac),
or water (lornoxicam), respectively. Negative and positive control
agents were also given (amitryptilline in the forced swimming test).
The cage floor used in the locomotor activity assessment was divided
into 20 equal 10 cm squares. The forced swimming test involved
partial immersion of the mice in cylinders (15/9cm height/diameter)
filled with water (10 cm depth at 28C), where they were left for 6
minutes. The cage endpoint used in the locomotor activity assessment
was the number of treaded squares. Four endpoints were used in the
forced swimming test (immobility latency for the entire 6 minutes,
and immobility, swimming, and climbing scores for the final 4
minutes of the swimming session), recorded by an observer that was
„blinded” to the experimental design. The statistical analysis used the
Levene test for variance homogeneity, ANOVA and post-hoc
analysis as appropriate, Tukey or Tamhane tests.
Results: No statistically significant increase or decrease in the
number of treaded squares was seen in the locomotor activity
assessment of any mice group. In the forced swimming test,
amitryptilline showed an antidepressant effect in each experiment, at
the 10 mg/kg bw dosage. Sodium metamizole was depressant at 100
mg/kg bw (increased the immobility score, p=0.049, Tamhane test),
but not in lower dosages as well (25 and 50 mg/kg bw). Ketorolac
showed an antidepressant effect at the intermediate dosage of 5
mg/kg bw, but not so in the dosages of 2.5 and 10 mg/kg bw,
respectively (increased the swimming score, p=0.012, Tamhane test).
Meloxicam and lornoxicam did not alter the forced swimming
endpoints at any dosage level.
Discussion: 1) Certain NSAIDs caused changes in the forced
swimming patterns without interfering with locomotion. 2) Sodium
metamizole showed a depressant effect, whereas ketorolac proved
antidepressant. Conclusion: NSAID-induced mood changes are not
class effects of these agents and apparently are independent of the
type of inhibited cyclooxygenase (COX-1 or COX-2).
Disclosure: This paper was co-financed from the European Social
Fund, through the Sectorial Operational Programme Human Resources Development 2007-2013, project number POSDRU /159
/1.5 /S /138907 "Excellence in scientific interdisciplinary research,
doctoral and postdoctoral, in the economic, social and medical fields
-EXCELIS", coordinator The Bucharest University of Economic
Studies.
Abstract: The concentrations of heavy metals in sediments of
Qua Iboe River Estuary (QIRE) were monitored at four different
sampling locations in wet and dry seasons. A preliminary survey to
determine the four sampling stations along the river continuum
showed that the area spanned between
Abstract: In this paper, we propose a system for preventing gas
risks through the use of wireless communication modules and
intelligent gas safety appliances. Our system configuration consists of
an automatic extinguishing system, detectors, a wall-pad, and a
microcomputer controlled micom gas meter to monitor gas flow and
pressure as well as the occurrence of earthquakes. The automatic fire
extinguishing system checks for both combustible gaseous leaks and
monitors the environmental temperature, while the detector array
measures smoke and CO gas concentrations. Depending on detected
conditions, the micom gas meter cuts off an inner valve and generates
a warning, the automatic fire-extinguishing system cuts off an external
valve and sprays extinguishing materials, or the sensors generate
signals and take further action when smoke or CO are detected.
Information on intelligent measures taken by the gas safety appliances
and sensors are transmitted to the wall-pad, which in turn relays this as
real time data to a server that can be monitored via an external network
(BcN) connection to a web or mobile application for the management
of gas safety. To validate this smart-home gas management system, we
field-tested its suitability for use in Korean apartments under several
scenarios.
Abstract: Phthalates are ubiquitous environmental pollutants
well known because of their endocrine disrupting activity in human
organism. The aim of our study was, by biological monitoring,
investigate exposure to phthalates of Roma ethnicity group i.e.
children and adults from 5 families (n=29, average age 11.8 ± 7.6
years) living in western Slovakia. Additionally, we analysed some
associations between anthropometric measures, questionnaire data
i.e. socio-economic status, eating and drinking habits, practise of
personal care products and household conditions in comparison with
concentrations of phthalate metabolites. We used for analysis of urine
samples high performance liquid chromatography and tandem mass
spectrometry (HPLC-MS/MS) to determine concentrations of
phthalate metabolites monoethyl phthalate (MEP), mono-n-butyl
phthalate (MnBP), mono-iso-butyl phthalate (MiBP), mono(2-ethyl-
5-hydroxyhexyl) phthalate (5OH-MEHP), mono(2-ethyl-5-oxohexyl)
phthalate (5oxo-MEHP) and mono(2-etylhexyl) phthalate (MEHP).
Our results indicate that ethnicity, lower socioeconomic status and
different housing conditions in Roma population can affect urinary
concentration of phthalate metabolites.
Abstract: Waste load allocation (WLA) policies may use multiobjective
optimization methods to find the most appropriate and
sustainable solutions. These usually intend to simultaneously
minimize two criteria, total abatement costs (TC) and environmental
violations (EV). If other criteria, such as inequity, need for
minimization as well, it requires introducing more binary
optimizations through different scenarios. In order to reduce the
calculation steps, this study presents value index as an innovative
decision making approach. Since the value index contains both the
environmental violation and treatment costs, it can be maximized
simultaneously with the equity index. It implies that the definition of
different scenarios for environmental violations is no longer required.
Furthermore, the solution is not necessarily the point with minimized
total costs or environmental violations. This idea is testified for Haraz
River, in north of Iran. Here, the dissolved oxygen (DO) level of river
is simulated by Streeter-Phelps equation in MATLAB software. The
WLA is determined for fish farms using multi-objective particle
swarm optimization (MOPSO) in two scenarios. At first, the trade-off
curves of TC-EV and TC-Inequity are plotted separately as the
conventional approach. In the second, the Value-Equity curve is
derived. The comparative results show that the solutions are in a
similar range of inequity with lower total costs. This is due to the
freedom of environmental violation attained in value index. As a
result, the conventional approach can well be replaced by the value
index particularly for problems optimizing these objectives. This
reduces the process to achieve the best solutions and may find better
classification for scenario definition. It is also concluded that decision
makers are better to focus on value index and weighting its contents
to find the most sustainable alternatives based on their requirements.
Abstract: In this research article of modeling Underwater
Wireless Sensor Network Simulators, we provide a comprehensive
overview of the various currently available simulators used in UWSN
modeling. In this work, we compare their working environment,
software platform, simulation language, key features, limitations and
corresponding applications. Based on extensive experimentation and
performance analysis, we provide their efficiency for specific
applications. We have also provided guidelines for developing
protocols in different layers of the protocol stack, and finally these
parameters are also compared and tabulated. This analysis is
significant for researchers and designers to find the right simulator
for their research activities.
Abstract: Many industrial materials like magnets need to be
tested for the radiation environment expected at linear colliders (LC)
where the accelerator and detectors will be subjected to large
influences of beta, neutron and gamma’s over their life Gamma
irradiation of the permanent sample magnets using a 60Co source was
investigated up to an absorbed dose of 700Mrad shows a negligible
effect on some magnetic properties of Nd-Fe-B. In this work it has
been tried to investigate the change of some important properties of
Barium hexa ferrite. Results showed little decreases of magnetic
properties at doses rang of 0.5 to 2.5 Mrad. But at the gamma
irradiation dose up to 10 Mrad it is showed a few increase of
properties. Also study of gamma irradiation of Nd-Fe-B showed
considerably increase of magnetic properties.
Abstract: One of the most famous techniques which affect the
efficiency of a production line is the assembly line balancing (ALB)
technique. This paper examines the balancing effect of a whole
production line of a real auto glass manufacturer in three steps. In the
first step, processing time of each activity in the workstations is
generated according to a practical approach. In the second step, the
whole production process is simulated and the bottleneck stations
have been identified, and finally in the third step, several
improvement scenarios are generated to optimize the system
throughput, and the best one is proposed. The main contribution of
the current research is the proposed framework which combines two
famous approaches including Assembly Line Balancing and
Optimization via Simulation technique (OvS). The results show that
the proposed framework could be applied in practical environments,
easily.
Abstract: The secondary alloy A226 is used for many
automotive casting produced by mould casting and high pressure die
casting. This alloy has excellent castability, good mechanical
properties and cost-effectiveness. Production of primary aluminium
alloys belong to heavy source fouling of life environs. The European
Union calls for the emission reduction and reduction in energy
consumption therefore increase production of recycled (secondary)
aluminium cast alloys. The contribution is deal with influence of
recycling on the quality of the casting made from A226 in automotive
industry. The properties of the casting made from secondary
aluminium alloys were compared with the required properties of
primary aluminium alloys. The effect of recycling on microstructure
was observed using combination different analytical techniques (light
microscopy upon black-white etching, scanning electron microscopy
- SEM upon deep etching and energy dispersive X-ray analysis -
EDX). These techniques were used for the identification of the
various structure parameters, which was used to compare secondary
alloy microstructure with primary alloy microstructure.
Abstract: The iron environment in Fe-doped Vycor Anode was
investigated with EXAFS using Brookhaven Synchrotron Light
Source. The iron-reducing Shewanella oneidensis culture was grown
in a microbial fuel cell under anaerobic respiration. The Fe bond
length was found to decrease and correlate with the amount of
biofilm growth on the Fe-doped Vycor Anode. The data suggests that
Fe-doped Vycor Anode would be a good substrate to study the
Shewanella oneidensis nanowire structure using EXAFS.
Abstract: The arsenic and iron environments in different growth
stages have been studied with EXAFS and XANES using
Brookhaven Synchrotron Light Source. Collard Greens plants were
grown and tissue samples were harvested. The project studied the
EXAFS and XANES of tissue samples using As and Fe K-edges. The
Fe absorption and the Fourier transform bond length information
were used as a control comparison. The Fourier transform of the
XAFS data revealed the coexistence of As (III) and As (V) in the As
bonding environment inside the studied plant tissue samples,
although the soil only had As (III). The data suggests that Collard
Greens has a novel pathway to handle arsenic absorption in soil.
Abstract: The aim of this paper is to present the concept of an
agile enterprise model and to initiate discussion on the research
assumptions of the model presented. The implementation of the
research project "The agility of enterprises in the process of adapting
to the environment and its changes" began in August 2014 and is
planned to last three years. The article has the form of a work-inprogress
paper which aims to verify and initiate a debate over the
proposed research model. In the literature there are very few
publications relating to research into agility; it can be concluded that
the most controversial issue in this regard is the method of measuring
agility. In previous studies the operationalization of agility was often
fragmentary, focusing only on selected areas of agility, for example
manufacturing, or analysing only selected sectors. As a result the
measures created to date can only be treated as contributory to the
development of precise measurement tools. This research project
aims to fill a cognitive gap in the literature with regard to the
conceptualization and operationalization of an agile company. Thus,
the original contribution of the author of this project is the
construction of a theoretical model that integrates manufacturing
agility (consisting mainly in adaptation to the environment) and
strategic agility (based on proactive measures). The author of this
research project is primarily interested in the attributes of an agile
enterprise which indicate that the company is able to rapidly adapt to
changing circumstances and behave pro-actively.