Abstract: A seismic isolation pad produced by utilizing the scrap
tire rubber which contains interleaved steel reinforcing cords has been
proposed. The steel cords are expected to function similar to the steel
plates used in conventional laminated rubber bearings. The scrap tire
rubber pad (STRP) isolator is intended to be used in low rise
residential buildings of highly seismic areas of the developing
countries. Experimental investigation was conducted on unbonded
STRP isolators, and test results provided useful information including
stiffness, damping values and an eventual instability of the isolation
unit. Finite element analysis (FE analysis) of STRP isolator was
carried out on properly bonded samples. These types of isolators
provide positive incremental force resisting capacity up to shear strain
level of 155%. This paper briefly discusses the force deformation
behavior of bonded STRP isolators including stability of the isolation
unit.
Abstract: A novel interpolation scheme to extend usable spectrum
and upconvert in high performance D/A converters is addressed in this
paper. By adjusting the pulse width of cycle and the production circuit
of code, the expansion code is a null code or complementary code that
is interpolation process. What the times and codes of interpolation
decide DAC works in one of a normal mode or multi-mixer mode
so that convert the input digital data signal into normal signal or a
mixed analog signal having a mixer frequency that is higher than the
data frequency. Simulation results show that the novel scheme and
apparatus most extend the usable frequency spectrum into fifth to
sixth Nyquist zone beyond conventional DACs.
Abstract: In this study, mechanically alloyed Al 2024 powder is
densified by conventional sintering and by equal channel angular
pressing (ECAP) with and without back pressure. The powder was
encapsulated in an aluminium can for consolidation through ECAP.
The properties obtained in the compacts by conventional sintering
route and by ECAP are compared. The effect of conventional
sintering and ECAP on consolidation behaviour of powder,
microstructure, density and hardness is discussed. Room temperature
back pressure aided ECAP results in nearly full denser (97% of its
theoretical density) compact at room temperature. NanoIndentation
technique was used to determine the modulus of the consolidated
compacts.
Abstract: The effect of Alumina nanoparticle size on thermophysical
properties, heat transfer performance and pressure loss characteristics of
Aviation Turbine Fuel (ATF)-Al2O3 nanofluids is studied experimentally for
the proposed application of regenerative cooling of semi-cryogenic rocket
engine thrust chambers. Al2O3 particles with mean diameters of 50 nm or 150
nm are dispersed in ATF. At 500C and 0.3% particle volume concentration,
the bigger particles show increases of 17% in thermal conductivity and 55% in
viscosity, whereas the smaller particles show corresponding increases of 21%
and 22% for thermal conductivity and viscosity respectively. Contrary to these
results, experiments to study the heat transfer performance and pressure loss
characteristics show that at the same pumping power, the maximum
enhancement in heat transfer coefficient at 500C and 0.3% concentration is
approximately 47% using bigger particles, whereas it is only 36% using
smaller particles.
Abstract: Composting is the process in which municipal solid
waste (MSW) and other organic waste materials such as biosolids
and manures are decomposed through the action of bacteria and other
microorganisms into a stable granular material which, applied to
land, as soil conditioner. Microorganisms, especially those that are
able to degrade polymeric organic material have a key role in speed
up this process. The aim of this study has been established to
isolation of microorganisms with high ability to production
extracellular enzymes for degradation of natural polymers that are
exists in MSW for decreasing time of degradation phase. Our
experimental study for isolation designed in two phases: in first
phase we isolated degrading microorganism with selected media that
consist a special natural polymer such as cellulose, starch, lipids and
etc as sole source of carbon. In second phase we selected
microorganism that had high degrading enzyme production with
enzymatic assay for seed production. However, our findings in pilot
scale have indicated that usage of this microbial consortium had high
efficiency for decreasing degradation phase.
Abstract: Multicast transmissions allow an host (the source) to send only one flow bound for a group of hosts (the receivers). Any equipment eager to belong to the group may explicitly register itself to that group via its multicast router. This router will be given the responsibility to convey all information relating to the group to all registered hosts. However in an environment in which the final receiver or the source frequently moves, the multicast flows need particular treatment. This constitutes one of the multicast transmissions problems around which several proposals were made in the Mobile IPv6 case in general. In this article, we describe the problems involved in this IPv6 multicast mobility and the existing proposals for their resolution. Then architecture will be proposed aiming to satisfy and optimize these transmissions in the specific case of a mobile multicast receiver in NC-HMIPv6 environment.
Abstract: If science is supposed to gain greater social
relevance and acceptance, researchers must not only relate to
the broader public, but also promote intercourse within the
ivory tower itself. The latter process has been under way
successfully for a number of years in the form of
transdisciplinary research initiatives. What is still lacking is a
broad debate about the necessity to look around properly and
face up to opposing views on one and the same topic within
our own discipline.
Abstract: Two indica varieties, IR36 and ‘Suweon 258’ (“S”)
are middle-heading in southern Japan. 36U, also middle-heading, is
an isogenic line of IR36 carrying Ur1 (Undulate rachis-1) gene.
However, late-heading plants segregated in the F2 population from
the F1 of S × 36U, and so did in the following generations. The
concerning lateness gene is designated as Ex. From the F8 generation,
isogenic-line pair of early-heading and late-heading lines, denoted by
“E” (ex/ex) and “L” (Ex/Ex), were developed. Genetic analyses of
heading time were conducted, using F1s and F2s among L, E, S and
36U. The following inferences were drawn from the experimental
results: 1) L, and both of E and 36U harbor Ex and ex, respectively;
2) Besides Ex, S harbors an inhibitor gene to it, i.e. I-Ex which is a
novel finding of the present study. 3) Ex is a dominant allele at the
E1 locus.
Abstract: The notions of intuitionistic fuzzy h-ideal and normal
intuitionistic fuzzy h-ideal in Γ-hemiring are introduced and some
of the basic properties of these ideals are investigated. Cartesian
product of intuitionistic fuzzy h-ideals is also defined. Finally a
characterization of intuitionistic fuzzy h-ideals in terms of fuzzy
relations is obtained.
Abstract: This paper presents a formalisation of the different existing code mutation techniques (polymorphism and metamorphism) by means of formal grammars. While very few theoretical results are known about the detection complexity of viral mutation techniques, we exhaustively address this critical issue by considering the Chomsky classification of formal grammars. This enables us to determine which family of code mutation techniques are likely to be detected or on the contrary are bound to remain undetected. As an illustration we then present, on a formal basis, a proof-of-concept metamorphic mutation engine denoted PB MOT, whose detection has been proven to be undecidable.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: This method decrease usage power (expenditure) in networks on chips (NOC). This method data coding for data transferring in order to reduces expenditure. This method uses data compression reduces the size. Expenditure calculation in NOC occurs inside of NOC based on grown models and transitive activities in entry ports. The goal of simulating is to weigh expenditure for encoding, decoding and compressing in Baseline networks and reduction of switches in this type of networks. KeywordsNetworks on chip, Compression, Encoding, Baseline networks, Banyan networks.
Abstract: Knowledge sharing enables the information or
knowledge to be transmitted from one source to another. This paper
demonstrates the needs of having the online book catalogue which
can be used to facilitate disseminating information on textbook used
in the university. This project is aimed to give access to the students
and lecturers to the list of books in the bookstore and at the same
time to allow book reviewing without having to visit the bookstore
physically. Research is carried out according to the boundaries which
accounts to current process of new book purchasing, current system
used by the bookstore and current process the lecturers go through
for reviewing textbooks. The questionnaire is used to gather the
requirements and it is distributed to 100 students and 40 lecturers.
This project has enabled the improvement of a manual process to be
carried out automatically, through a web based platform. It is shown
based on the user acceptance survey carried out that target groups
found that this web service is feasible to be implemented in
Universiti Teknologi PETRONAS (UTP), and they have shown
positive signs of interest in utilizing it in the future.
Abstract: This research were investigated, determined, and
analyzed of the climate characteristically change in the provincial
Udon Thani in the period of 60 surrounding years from 1951 to 2010
A.D. that it-s transferred to effects of climatologically data for
determining global warming. Statistically significant were not found
for the 60 years- data (R2
Abstract: This paper presents a novel methodology for Maximum Power Point Tracking (MPPT) of a grid-connected 20 kW Photovoltaic (PV) system using neuro-fuzzy network. The proposed method predicts the reference PV voltage guarantying optimal power transfer between the PV generator and the main utility grid. The neuro-fuzzy network is composed of a fuzzy rule-based classifier and three Radial Basis Function Neural Networks (RBFNN). Inputs of the network (irradiance and temperature) are classified before they are fed into the appropriated RBFNN for either training or estimation process while the output is the reference voltage. The main advantage of the proposed methodology, comparing to a conventional single neural network-based approach, is the distinct generalization ability regarding to the nonlinear and dynamic behavior of a PV generator. In fact, the neuro-fuzzy network is a neural network based multi-model machine learning that defines a set of local models emulating the complex and non-linear behavior of a PV generator under a wide range of operating conditions. Simulation results under several rapid irradiance variations proved that the proposed MPPT method fulfilled the highest efficiency comparing to a conventional single neural network.
Abstract: The main goal of this work is to propose a way for
combined use of two nontraditional algorithms by solving topological
problems on telecommunications concentrator networks. The
algorithms suggested are the Simulated Annealing algorithm and the
Genetic Algorithm. The Algorithm of Simulated Annealing unifies
the well known local search algorithms. In addition - Simulated
Annealing allows acceptation of moves in the search space witch lead
to decisions with higher cost in order to attempt to overcome any
local minima obtained. The Genetic Algorithm is a heuristic approach
witch is being used in wide areas of optimization works. In the last
years this approach is also widely implemented in
Telecommunications Networks Planning. In order to solve less or
more complex planning problem it is important to find the most
appropriate parameters for initializing the function of the algorithm.
Abstract: Nowadays, the rapid development of multimedia
and internet allows for wide distribution of digital media data.
It becomes much easier to edit, modify and duplicate digital
information Besides that, digital documents are also easy to
copy and distribute, therefore it will be faced by many
threatens. It-s a big security and privacy issue with the large
flood of information and the development of the digital
format, it become necessary to find appropriate protection
because of the significance, accuracy and sensitivity of the
information. Nowadays protection system classified with more
specific as hiding information, encryption information, and
combination between hiding and encryption to increase information
security, the strength of the information hiding science is due to the
non-existence of standard algorithms to be used in hiding secret
messages. Also there is randomness in hiding methods such as
combining several media (covers) with different methods to pass a
secret message. In addition, there are no formal methods to be
followed to discover the hidden data. For this reason, the task of this
research becomes difficult. In this paper, a new system of information
hiding is presented. The proposed system aim to hidden information
(data file) in any execution file (EXE) and to detect the hidden file
and we will see implementation of steganography system which
embeds information in an execution file. (EXE) files have been
investigated. The system tries to find a solution to the size of the
cover file and making it undetectable by anti-virus software. The
system includes two main functions; first is the hiding of the
information in a Portable Executable File (EXE), through the
execution of four process (specify the cover file, specify the
information file, encryption of the information, and hiding the
information) and the second function is the extraction of the hiding
information through three process (specify the steno file, extract the
information, and decryption of the information). The system has
achieved the main goals, such as make the relation of the size of the
cover file and the size of information independent and the result file
does not make any conflict with anti-virus software.
Abstract: The aim of this article is to narrate the utility of novel simulation approach i.e. convolution method to predict blood concentration of drug utilizing dissolution data of salbutamol sulphate microparticulate formulations with different release patterns (1:1, 1:2 and 1:3, drug:polymer). Dissolution apparatus II USP 2007 and 900 ml double distilled water stirrd at 50 rpm was employed for dissolution analysis. From dissolution data, blood drug concentration was determined, and in return predicted blood drug concentration data was used to calculate the pharmacokinetic parameters i.e. Cmax, Tmax, and AUC. Convolution is a good biwaiver technique; however its better utility needs it application in the conditions where biorelevant dissolution media are used.
Abstract: The world is moving rapidly toward the deployment
of information and communication systems. Nowadays, computing
systems with their fast growth are found everywhere and one of the main challenges for these systems is increasing attacks and security threats against them. Thus, capturing, analyzing and verifying security requirements becomes a very important activity in
development process of computing systems, specially in developing
systems such as banking, military and e-business systems. For
developing every system, a process model which includes a process,
methods and tools is chosen. The Rational Unified Process (RUP) is
one of the most popular and complete process models which is used
by developers in recent years. This process model should be extended to be used in developing secure software systems. In this
paper, the Requirement Discipline of RUP is extended to improve RUP for developing secure software systems. These proposed extensions are adding and integrating a number of Activities, Roles,
and Artifacts to RUP in order to capture, document and model threats
and security requirements of system. These extensions introduce a
group of clear and stepwise activities to developers. By following these activities, developers assure that security requirements are
captured and modeled. These models are used in design, implementation and test activitie
Abstract: This paper compares planning results of the electricity and water generation inventory up to year 2030 in the State of
Kuwait. Currently, the generation inventory consists of oil and gas fired technologies only. The planning study considers two main cases. The first case, Reference case, examines a generation inventory based on oil and gas fired generation technologies only.
The second case examines the inclusion of renewables as part of the generation inventory under two scenarios. In the first scenario, Ref-RE, renewable build-out is based on optimum economic performance
of overall generation system. Result shows that the optimum installed
renewable capacity with electric energy generation of 11% . In the second scenario, Ref-RE20, the renewable capacity build-out is
forced to provide 20% of electric energy by 2030. The respective energy systems costs of Reference, Ref-RE and Ref-RE20 case
scenarios reach US dollar 24, 10 and 14 billion annually in 2030.