Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: Orthogonal Frequency Division Multiplexing (OFDM) is one of the techniques for high speed data rate communication with main consideration for 4G and 5G systems. In OFDM, there are several mapping schemes which provide a way of parallel transmission. In this paper, comparisons of mapping schemes used by some standards have been made and also has been discussed about the performance of the non-conventional modulation technique. The Comparisons of Bit Error Rate (BER) performances for conventional and non-conventional modulation schemes have been done using MATLAB software. Mentioned schemes used in OFDM system can be selected on the basis of the requirement of power or spectrum efficiency and BER analysis.
Abstract: In this paper, we study on finite projective Hjelmslev planes M(Zq) coordinatized by Hjelmslev ring Zq (where prime power q = pk). We obtain finite hyperbolic Klingenberg planes from these planes under certain conditions. Also, we give a combinatorical result on M(Zq), related by deleting a line from lines in same neighbour.
Abstract: Ant colony optimization is an ant algorithm framework that took inspiration from foraging behavior of ant colonies. Indeed, ACO algorithms use a chemical communication, represented by pheromone trails, to build good solutions. However, ants involve different communication channels to interact. Thus, this paper introduces the acoustic communication between ants while they are foraging. This process allows fine and local exploration of search space and permits optimal solution to be improved.
Abstract: The aim of the current work is to present a comparison among three popular optimization methods in the inverse elastostatics problem (IESP) of flaw detection within a solid. In more details, the performance of a simulated annealing, a Hooke & Jeeves and a sequential quadratic programming algorithm was studied in the test case of one circular flaw in a plate solved by both the boundary element (BEM) and the finite element method (FEM). The proposed optimization methods use a cost function that utilizes the displacements of the static response. The methods were ranked according to the required number of iterations to converge and to their ability to locate the global optimum. Hence, a clear impression regarding the performance of the aforementioned algorithms in flaw identification problems was obtained. Furthermore, the coupling of BEM or FEM with these optimization methods was investigated in order to track differences in their performance.
Abstract: In this paper we propose a novel Run Time Interface
(RTI) technique to provide an efficient environment for MPI jobs on
the heterogeneous architecture of PARAM Padma. It suggests an
innovative, unified framework for the job management interface
system in parallel and distributed computing. This approach employs
proxy scheme. The implementation shows that the proposed RTI is
highly scalable and stable. Moreover RTI provides the storage access
for the MPI jobs in various operating system platforms and improve
the data access performance through high performance C-DAC
Parallel File System (C-PFS). The performance of the RTI is
evaluated by using the standard HPC benchmark suites and the
simulation results show that the proposed RTI gives good
performance on large scale supercomputing system.
Abstract: The industrial process of the sugar cane crystallization produces a residual that still contains a lot of soluble sucrose and the objective of the factory is to improve its extraction. Therefore, there are substantial losses justifying the search for the optimization of the process. Crystallization process studied on the industrial site is based on the “three massecuites process". The third step of this process constitutes the final stage of exhaustion of the sucrose dissolved in the mother liquor. During the process of the third step of crystallization (Ccrystallization), the phase that is studied and whose control is to be improved, is the growing phase (crystal growth phase). The study of this process on the industrial site is a problem in its own. A control scheme is proposed to improve the standard PID control law used in the factory. An auto-tuning PID controller based on instantaneous linearization of a neural network is then proposed.
Abstract: Bumpers play an important role in preventing the
impact energy from being transferred to the automobile and
passengers. Saving the impact energy in the bumper to be released in
the environment reduces the damages of the automobile and
passengers.
The goal of this paper is to design a bumper with minimum weight
by employing the Glass Material Thermoplastic (GMT) materials.
This bumper either absorbs the impact energy with its deformation or
transfers it perpendicular to the impact direction.
To reach this aim, a mechanism is designed to convert about 80%
of the kinetic impact energy to the spring potential energy and
release it to the environment in the low impact velocity according to
American standard1. In addition, since the residual kinetic energy
will be damped with the infinitesimal elastic deformation of the
bumper elements, the passengers will not sense any impact. It should
be noted that in this paper, modeling, solving and result-s analysis
are done in CATIA, LS-DYNA and ANSYS V8.0 software
respectively.
Abstract: True stress-strain curve of railhead steel is required to
investigate the behaviour of railhead under wheel loading through elasto-plastic Finite Element (FE) analysis. To reduce the rate of wear, the railhead material is hardened through annealing and
quenching. The Australian standard rail sections are not fully hardened and hence suffer from non-uniform distribution of the
material property; usage of average properties in the FE modelling can potentially induce error in the predicted plastic strains. Coupons
obtained at varying depths of the railhead were, therefore, tested under axial tension and the strains were measured using strain gauges as well as an image analysis technique, known as the Particle Image Velocimetry (PIV). The head hardened steel exhibit existence of three distinct zones of yield strength; the yield strength as the ratio of the average yield strength provided in the standard (σyr=780MPa) and
the corresponding depth as the ratio of the head hardened zone along
the axis of symmetry are as follows: (1.17 σyr, 20%), (1.06 σyr, 20%-80%) and (0.71 σyr, > 80%). The stress-strain curves exhibit limited plastic zone with fracture occurring at strain less than 0.1.
Abstract: This paper presents a wavelet transform and Support
Vector Machine (SVM) based algorithm for estimating fault location
on transmission lines. The Discrete wavelet transform (DWT) is used
for data pre-processing and this data are used for training and testing
SVM. Five types of mother wavelet are used for signal processing to
identify a suitable wavelet family that is more appropriate for use in
estimating fault location. The results demonstrated the ability of SVM
to generalize the situation from the provided patterns and to
accurately estimate the location of faults with varying fault resistance.
Abstract: Modeling of complex dynamic systems, which are
very complicated to establish mathematical models, requires new and
modern methodologies that will exploit the existing expert
knowledge, human experience and historical data. Fuzzy cognitive
maps are very suitable, simple, and powerful tools for simulation and
analysis of these kinds of dynamic systems. However, human experts
are subjective and can handle only relatively simple fuzzy cognitive
maps; therefore, there is a need of developing new approaches for an
automated generation of fuzzy cognitive maps using historical data.
In this study, a new learning algorithm, which is called Big Bang-Big
Crunch, is proposed for the first time in literature for an automated
generation of fuzzy cognitive maps from data. Two real-world
examples; namely a process control system and radiation therapy
process, and one synthetic model are used to emphasize the
effectiveness and usefulness of the proposed methodology.
Abstract: The log periodogram regression is widely used in empirical
applications because of its simplicity, since only a least squares
regression is required to estimate the memory parameter, d, its good
asymptotic properties and its robustness to misspecification of the
short term behavior of the series. However, the asymptotic distribution
is a poor approximation of the (unknown) finite sample distribution
if the sample size is small. Here the finite sample performance of different
nonparametric residual bootstrap procedures is analyzed when
applied to construct confidence intervals. In particular, in addition to
the basic residual bootstrap, the local and block bootstrap that might
adequately replicate the structure that may arise in the errors of the
regression are considered when the series shows weak dependence in
addition to the long memory component. Bias correcting bootstrap
to adjust the bias caused by that structure is also considered. Finally,
the performance of the bootstrap in log periodogram regression based
confidence intervals is assessed in different type of models and how
its performance changes as sample size increases.
Abstract: Vertex configuration for a vertex in an orthogonal
pseudo-polyhedron is an identity of a vertex that is determined by the
number of edges, dihedral angles, and non-manifold properties
meeting at the vertex. There are up to sixteen vertex configurations
for any orthogonal pseudo-polyhedron (OPP). Understanding the
relationship between these vertex configurations will give us insight
into the structure of an OPP and help us design better algorithms for
many 3-dimensional geometric problems. In this paper, 16 vertex
configurations for OPP are described first. This is followed by a
number of formulas giving insight into the relationship between
different vertex configurations in an OPP. These formulas
will be useful as an extension of orthogonal polyhedra usefulness on
pattern analysis in 3D-digital images.
Abstract: The goal of speech parameterization is to extract the relevant information about what is being spoken from the audio signal. In speech recognition systems Mel-Frequency Cepstral Coefficients (MFCC) and Relative Spectral Mel-Frequency Cepstral Coefficients (RASTA-MFCC) are the two main techniques used. It will be shown in this paper that it presents some modifications to the original MFCC method. In our work the effectiveness of proposed changes to MFCC called Modified Function Cepstral Coefficients (MODFCC) were tested and compared against the original MFCC and RASTA-MFCC features. The prosodic features such as jitter and shimmer are added to baseline spectral features. The above-mentioned techniques were tested with impulsive signals under various noisy conditions within AURORA databases.
Abstract: This paper presents a distributed intrusion
detection system IDS, based on the concept of specialized
distributed agents community representing agents with the
same purpose for detecting distributed attacks. The semantic of
intrusion events occurring in a predetermined network has been
defined. The correlation rules referring the process which our
proposed IDS combines the captured events that is distributed
both spatially and temporally. And then the proposed IDS tries
to extract significant and broad patterns for set of well-known
attacks. The primary goal of our work is to provide intrusion
detection and real-time prevention capability against insider
attacks in distributed and fully automated environments.
Abstract: Purpose of this work is the development of an
automatic classification system which could be useful for radiologists
in the investigation of breast cancer. The software has been designed
in the framework of the MAGIC-5 collaboration.
In the automatic classification system the suspicious regions with
high probability to include a lesion are extracted from the image as
regions of interest (ROIs). Each ROI is characterized by some
features based on morphological lesion differences.
Some classifiers as a Feed Forward Neural Network, a K-Nearest
Neighbours and a Support Vector Machine are used to distinguish the
pathological records from the healthy ones.
The results obtained in terms of sensitivity (percentage of
pathological ROIs correctly classified) and specificity (percentage of
non-pathological ROIs correctly classified) will be presented through
the Receive Operating Characteristic curve (ROC). In particular the
best performances are 88% ± 1 of area under ROC curve obtained
with the Feed Forward Neural Network.
Abstract: Ultrafast doped zinc oxide crystal promised us a good
opportunity to build new instruments for ICF fusion neutron
measurement. Two pulsed neutron detectors based on ZnO crystal
wafer have been conceptually designed, the superfast ZnO timing
detector and the scintillation recoil proton neutron detection system.
The structure of these detectors was presented, and some characters
were studied as well. The new detectors could be much faster than
existing systems, and would be more competent for ICF neutron
diagnostics.
Abstract: Efficient modulo 2n+1 adders are important for
several applications including residue number system, digital signal
processors and cryptography algorithms. In this paper we present a
novel modulo 2n+1 addition algorithm for a recently represented
number system. The proposed approach is introduced for the
reduction of the power dissipated. In a conventional modulo 2n+1
adder, all operands have (n+1)-bit length. To avoid using (n+1)-bit
circuits, the diminished-1 and carry save diminished-1 number
systems can be effectively used in applications. In the paper, we also
derive two new architectures for designing modulo 2n+1 adder, based
on n-bit ripple-carry adder. The first architecture is a faster design
whereas the second one uses less hardware. In the proposed method,
the special treatment required for zero operands in Diminished-1
number system is removed. In the fastest modulo 2n+1 adders in
normal binary system, there are 3-operand adders. This problem is
also resolved in this paper. The proposed architectures are compared
with some efficient adders based on ripple-carry adder and highspeed
adder. It is shown that the hardware overhead and power
consumption will be reduced. As well as power reduction, in some
cases, power-delay product will be also reduced.
Abstract: Wireless Sensor Network is Multi hop Self-configuring
Wireless Network consisting of sensor nodes. The deployment of
wireless sensor networks in many application areas, e.g., aggregation
services, requires self-organization of the network nodes into clusters.
Efficient way to enhance the lifetime of the system is to partition the
network into distinct clusters with a high energy node as cluster head.
The different methods of node clustering techniques have appeared in
the literature, and roughly fall into two families; those based on the
construction of a dominating set and those which are based solely on
energy considerations. Energy optimized cluster formation for a set
of randomly scattered wireless sensors is presented. Sensors within a
cluster are expected to be communicating with cluster head only. The
energy constraint and limited computing resources of the sensor nodes
present the major challenges in gathering the data. In this paper we
propose a framework to study how partially correlated data affect the
performance of clustering algorithms. The total energy consumption
and network lifetime can be analyzed by combining random geometry
techniques and rate distortion theory. We also present the relation
between compression distortion and data correlation.
Abstract: Value engineering is an efficacious contraption for
administrators to make up their minds. Value perusals proffer the
gaffers a suitable instrument to decrease the expenditures of the life
span, quality amelioration, structural improvement, curtailment of the
construction schedule, longevity prolongation or a merging of the
aforementioned cases. Subjecting organizers to pressures on one
hand and their accountability towards their pertinent fields together
with inherent risks and ambiguities of other options on the other hand
set some comptrollers in a dilemma utilization of risk management
and the value engineering in projects manipulation with regard to
complexities of implementing projects can be wielded as a
contraption to identify and efface each item which wreaks
unnecessary expenses and time squandering sans inflicting any
damages upon the essential project applications. Of course It should
be noted that implementation of risk management and value
engineering with regard to the betterment of efficiency and functions
may lead to the project implementation timing elongation. Here time
revamping does not refer to time diminishing in the whole cases. his
article deals with risk and value engineering conceptualizations at
first. The germane reverberations effectuated due to its execution in
Iran Khodro Corporation are regarded together with the joint features
and amalgamation of the aforesaid entia; hence the proposed
blueprint is submitted to be taken advantage of in engineering and
industrial projects including Iran Khodro Corporation.