Abstract: Biodiesel as an alternative diesel fuel is steadily gaining more attention and significance. However, there are some drawbacks while using biodiesel regarding its properties that requires it to be blended with petrol based diesel and/or additives to improve the fuel characteristics. This study analyses thermal cracking as an alternative technology to improve biodiesel characteristics in which, FAME based biodiesel produced by transesterification of castor oil is fed into a continuous thermal cracking reactor at temperatures range of 450-500°C and flowrate range of 20-40 g/hr. Experiments designed by response surface methodology and subsequent statistical studies show that temperature and feed flowrate significantly affect the products yield. Response surfaces were used to study the impact of temperature and flowrate on the product properties. After each experiment, the produced crude bio-oil was distilled and diesel cut was separated. As shorter chain molecules are produced through thermal cracking, the distillation curve of the diesel cut fitted more with petrol based diesel curve in comparison to the biodiesel. Moreover, the produced diesel cut properties adequately pose within property ranges defined by the related standard of petrol based diesel. Cold flow properties, high heating value as the main drawbacks of the biodiesel are improved by this technology. Thermal cracking decreases kinematic viscosity, Flash point and cetane number.
Abstract: There is not much effective guideline on development of design parameters selection on spring back for advanced high strength steel sheet metal in U-channel process during cold forming process. This paper presents the development of predictive model for spring back in U-channel process on advanced high strength steel sheet employing Response Surface Methodology (RSM). The experimental was performed on dual phase steel sheet, DP590 in Uchannel forming process while design of experiment (DoE) approach was used to investigates the effects of four factors namely blank holder force (BHF), clearance (C) and punch travel (Tp) and rolling direction (R) were used as input parameters using two level values by applying Full Factorial design (24 ). From a statistical analysis of variant (ANOVA), result showed that blank holder force (BHF), clearance (C) and punch travel (Tp) displayed significant effect on spring back of flange angle (β2 ) and wall opening angle (β1 ), while rolling direction (R) factor is insignificant. The significant parameters are optimized in order to reduce the spring back behavior using Central Composite Design (CCD) in RSM and the optimum parameters were determined. A regression model for spring back was developed. The effect of individual parameters and their response was also evaluated. The results obtained from optimum model are in agreement with the experimental values.
Abstract: An experiment was conducted to elucidate the effects of turmeric powder supplementation on egg production performance of old laying hens (80 weeks of age). There were 40 hens of Hysex Brown strain used in the study. They were caged individually, and randomly divided into 4 treatment groups of diet containing 0 (control), 1, 2 and 4 % oven dried turmeric powder for 3 periods of 4 weeks; Egg production (% hen day) and feed intake of the 4 treatment groups at the commencement of the experiment were not significantly different. In addition to egg production performance (% and egg weight), feed and water intakes were measured daily, and cholesterol content of the whole egg was determined. The results indicated that feed intakes of the hen were significantly lowered when 4% turmeric powder supplemented, while there were no significant changes in water intakes. Egg production were significantly increased and maintained at a higher level by turmeric powder supplementation up to 4% compared with the control, while the weight of eggs were not significantly affected. The research markedly demonstrated that supplementation of turmeric powder up to 4% could improve and maintain egg production performance of the old laying hen at a higher level with a lower cholesterol content.
Abstract: Exploration and exploitation capabilities are both
important within Operations as means for improvement when
managed separately, and for establishing dynamic improvement
capabilities when combined in balance. However, it is unclear what
exploration and exploitation capabilities imply in improvement and
development work within an Operations context. So, in order to
better understand how to develop exploration and exploitation
capabilities within Operations, the main characteristics of these
constructs needs to be identified and further understood. Thus, the
objective of this research is to increase the understanding about
exploitation and exploration characteristics, to concretize what they
translates to within the context of improvement and development
work in an Operations unit, and to identify practical challenges. A
literature review and a case study are presented. In the literature
review, different interpretations of exploration and exploitation are
portrayed, key characteristics have been identified, and a deepened
understanding of exploration and exploitation characteristics is
described. The case in the study is an Operations unit, and the aim is
to explore to what extent and in what ways exploration and
exploitation activities are part of the improvement structures and
processes. The contribution includes an identification of key
characteristics of exploitation and exploration, as well as an
interpretation of the constructs. Further, some practical challenges are
identified. For instance, exploration activities tend to be given low
priority, both in daily work as in the manufacturing strategy. Also,
the overall understanding about the concepts of exploitation and
exploration (or any similar aspect of dynamic improvement
capabilities) is very low.
Abstract: In the immunologic sense, clinical infection is a state
of failure of the immune system to combat the pathogenic weapon of
the bacteria invading the host. A motile gram negative vibroid
organism associated with marked mono and poly nuclear cell
responses was traced during the examination of a clinical material
from an infected common carp Cyprinus carpio. On primary plate
culture, growth was shown to be pure, dense population of an
Aeromonas-like colony morphotype. The pure isolate was found to
be; Aerobic, facultatively anaerobic, non-halophilic, grew at 0C, and
37C, oxidase positive utilizes glucose through fermentative pathway,
resist 0/129 and novobiocin, produces alanine and lysine
decarboxylases but non-producing ornithine dehydrolases. Tests for
the in vitro determinants of pathogenicity has shown to be; Betahaemolytic
onto blood agar, gelatinase, casienase and amylase
producer. Three in vivo determinants of pathogenicity were tested as,
the lethal dose fifty, the pathogenesis and pathogenicity. It was
evident that 0.1 milliliter of the causal bacterial cell suspension of a
density 1 x 107 CFU/ml injected intramuscularly into an average of
100gms fish toke five days incubation period, then at the day six
morbidity and mortality were initiated. LD50 was recorded at the day
12 post-infection. Use of an LD50 doses to study the pathogenicity,
reveals mononuclear and polynuclear cell responses, on examining
the stained direct films of the clinical materials from the
experimentally infected fish. Re-isolation tests confirm that the reisolant
is same. The course of the infection in natural case was shown
manifestation of; skin ulceration, haemorrhage and descaling. On
evisceration, the internal organs were shown; congestion in the
intestines, spleen and, air sacs. The induced infection showed a
milder form of these manifestations. The grading of the virulence of
this organism was virulent causing chronic course of infections as
indicated from the pathogenesis and pathogenicity studies. Thus the
infectious bacteria were consistent with Aeromonas hydrophila, and
the infection was chronic.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Nowadays, the rapid development of CAD systems’
programming environments results in the creation of multiple
downstream applications, which are developed and becoming
increasingly available. CAD based manufacturing simulations is
gradually following the same trend. Drilling is the most popular holemaking
process used in a variety of industries. A specially built piece
of software that deals with the drilling kinematics is presented. The
cutting forces are calculated based on the tool geometry, the cutting
conditions and the tool/work-piece materials. The results are verified
by experimental work. Finally, the response surface methodology
(RSM) is applied and mathematical models of the total thrust force
and the thrust force developed because of the main cutting edges are
proposed.
Abstract: When neck pain is associated with pain, numbness, or
weakness in the arm, shoulder, or hand, further investigation is
needed as these are symptoms indicating pressure on one or more
nerve roots. Evaluation necessitates a neurologic examination and
imaging using an MRI/CT scan. A degenerating disc loses some
thickness and is less flexible, causing inter-vertebrae space to narrow.
A radiologist diagnoses an Intervertebral Disc Degeneration (IDD) by
localizing every inter-vertebral disc and identifying the pathology in
a disc based on its geometry and appearance. Accurate localizing is
necessary to diagnose IDD pathology. But, the underlying image
signal is ambiguous: a disc’s intensity overlaps the spinal nerve
fibres. Even the structure changes from case to case, with possible
spinal column bending (scoliosis). The inter-vertebral disc
pathology’s quantitative assessment needs accurate localization of the
cervical region discs. In this work, the efficacy of multilevel set
segmentation model, to segment cervical discs is investigated. The
segmented images are annotated using a simple distance matrix.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: A compound parabolic concentrator (CPC) is a wellknown
non-imaging concentrator that will concentrate the solar
radiation onto receiver (PV cell). One of disadvantage of CPC is has
tall and narrow height compared to its diameter entry aperture area.
Therefore, for economic reason, a truncation had been done by
removed from the top of the full height CPC. This also will lead to
the decreases of concentration ratio but it will be negligible. In this
paper, the flux distribution of untruncated and truncated 2-D hollow
compound parabolic trough concentrator (hCPTC) design is
presented. The untruncated design has initial height H=193.4mm
with concentration ratio C_(2-D)=4. This paper presents the optical
simulation of compound parabolic trough concentrator using raytracing
software TracePro. Results showed that, after the truncation,
the height of CPC reduced 45% from initial height with the
geometrical concentration ratio only decrease 10%. Thus, the cost of
reflector and material dielectric usage can be saved especially at
manufacturing site.
Abstract: Total Quality Management (TQM) is a managerial
approach that improves the competitiveness of the industry,
meanwhile Information technology (IT) was introduced with TQM
for handling the technical issues which is supported by quality
experts for fulfilling the customers’ requirement. Present paper aims
to utilise AHP (Analytic Hierarchy Process) methodology to
priorities and rank the hierarchy levels of TQM enablers and IT
resource together for its successful implementation in the Information
and Communication Technology (ICT) industry. A total of 17 TQM
enablers (nine) and IT resources (eight) were identified and
partitioned into 3 categories and were prioritised by AHP approach.
The finding indicates that the 17 sub-criteria can be grouped into
three main categories namely organizing, tools and techniques, and
culture and people. Further, out of 17 sub-criteria, three sub-criteria:
top management commitment and support, total employee
involvement, and continuous improvement got highest priority
whereas three sub-criteria such as structural equation modelling,
culture change, and customer satisfaction got lowest priority. The
result suggests a hierarchy model for ICT industry to prioritise the
enablers and resources as well as to improve the TQM and IT
performance in the ICT industry. This paper has some managerial
implication which suggests the managers of ICT industry to
implement TQM and IT together in their organizations to get
maximum benefits and how to utilize available resources. At the end,
conclusions, limitation, future scope of the study are presented.
Abstract: Because blueberries are worldwide recognized as a
good source of beneficial components, their consumption has
increased in the past decades, and so have the scientific works about
their properties. Hence, this work was undertaken to evaluate the
effect of some production and conservation factors on the properties
of blueberries from cultivar Bluecrop. The physical and chemical
analyses were done according to established methodologies and then
all data was treated using software SPSS for assessment of the
possible differences among the factors investigated and/or the
correlations between the variables at study. The results showed that
location of production influenced some of the berries properties
(caliber, sugars, antioxidant activity, color and texture) and that the
age of the bushes was correlated with moisture, sugars and acidity, as
well as lightness. On the other hand, altitude of the farm only was
correlated to sugar content. With regards to conservation, it
influenced only anthocyanins content and DPPH antioxidant activity.
Finally, the type of extract and the order of extraction had a
pronounced influence on all the phenolic properties evaluated.
Abstract: In the past decade, the use of digital image correlation
(DIC) techniques has increased significantly in the area of
experimental mechanics, especially for materials behavior
characterization. This non-contact tool enables full field displacement
and strain measurements over a complete region of interest. The DIC
algorithm requires a random contrast pattern on the surface of the
specimen in order to perform properly. To create this pattern, the
specimen is usually first coated using a white matt paint. Next, a
black random speckle pattern is applied using any suitable method. If
the applied paint coating is too thick, its top surface may not be able
to exactly follow the deformation of the specimen, and consequently,
the strain measurement might be underestimated. In the present
article, a study of the influence of the paint thickness on the strain
underestimation is performed for different strain levels. The results
are then compared to typical paint coating thicknesses applied by
experienced DIC users. A slight strain underestimation was observed
for paint coatings thicker than about 30μm. On the other hand, this
value was found to be uncommonly high compared to coating
thicknesses applied by DIC users.
Abstract: A novel design technique employing CMOS Current
Feedback Operational Amplifier (CFOA) is presented. The feature of
consumption very low power in designing pseudo-OTA is used to
decreasing the total power consumption of the proposed CFOA. This
design approach applies pseudo-OTA as input stage cascaded with
buffer stage. Moreover, the DC input offset voltage and harmonic
distortion (HD) of the proposed CFOA are very low values compared
with the conventional CMOS CFOA due to the symmetrical input
stage. P-Spice simulation results are obtained using 0.18μm MIETEC
CMOS process parameters and supply voltage of ±1.2V, 50μA
biasing current. The p-spice simulation shows excellent improvement
of the proposed CFOA over existing CMOS CFOA. Some of these
performance parameters, for example, are DC gain of 62. dB, openloop
gain bandwidth product of 108 MHz, slew rate (SR+) of
+71.2V/μS, THD of -63dB and DC consumption power (PC) of
2mW.
Abstract: This paper presents an optimization method for
reducing the number of input channels and the complexity of the
feed-forward NARX neural network (NN) without compromising the
accuracy of the NN model. By utilizing the correlation analysis
method, the most significant regressors are selected to form the input
layer of the NN structure. An application of vehicle dynamic model
identification is also presented in this paper to demonstrate the
optimization technique and the optimal input layer structure and the
optimal number of neurons for the neural network is investigated.
Abstract: Driver fatigue is an important factor in the increasing
number of road accidents. Dynamic template matching method was
proposed to address the problem of real-time driver fatigue detection
system based on eye-tracking. An effective vision based approach
was used to analyze the driver’s eye state to detect fatigue. The driver
fatigue system consists of Face detection, Eye detection, Eye
tracking, and Fatigue detection. Initially frames are captured from a
color video in a car dashboard and transformed from RGB into YCbCr
color space to detect the driver’s face. Canny edge operator was used
to estimating the eye region and the locations of eyes are extracted.
The extracted eyes were considered as a template matching for eye
tracking. Edge Map Overlapping (EMO) and Edge Pixel Count
(EPC) matching function were used for eye tracking which is used to
improve the matching accuracy. The pixel of eyeball was tracked
from the eye regions which are used to determine the fatigue state of
the driver.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.
Abstract: In this paper, a new concept of closed-loop design for a
product is presented. The closed-loop design model is developed by
integrating forward design and reverse design. Based on this new
concept, a closed-loop design model for sustainable manufacturing by
integrated evaluation of forward design, reverse design, and green
manufacturing using a fuzzy analytic network process is developed. In
the design stage of a product, with a given product requirement and
objective, there can be different ways to design the detailed
components and specifications. Therefore, there can be different
design cases to achieve the same product requirement and objective.
Subsequently, in the design evaluation stage, it is required to analyze
and evaluate the different design cases. The purpose of this research is
to develop a model for evaluating the design cases by integrated
evaluating the criteria in forward design, reverse design, and green
manufacturing. A fuzzy analytic network process method is presented
for integrated evaluation of the criteria in the three models. The
comparison matrices for evaluating the criteria in the three groups are
established. The total relational values among the three groups
represent the total relational effects. In applications, a super matrix
model is created and the total relational values can be used to evaluate
the design cases for decision-making to select the final design case. An
example product is demonstrated in this presentation. It shows that the
model is useful for integrated evaluation of forward design, reverse
design, and green manufacturing to achieve a closed-loop design for
sustainable manufacturing objective.
Abstract: Electrodeposition is a simple and economic technique
for precision coating of different shaped substrates with pure metal,
alloy or composite films. Dc electrodeposition was used to produce
Cr, Co-Cr and Co-Cr/TiO2 nano-composite coatings from Cr(III)
based electrolytes onto 316L SS substrates. The effects of TiO2 nanoparticles
concentration on co-deposition of these particles along with
Cr content and microhardness of the coatings were investigated.
Morphology of the Cr, Co-Cr and Co-Cr/TiO2 coatings besides their
tribological behavior were studied. The results showed that increment
of TiO2 nanoparticles concentration from 0 to 30 g L-1 in the bath
increased their co-deposition and Cr content of the coatings from 0 to
3.5 wt.% and from 23.7 to 31.2 wt.%, respectively. Microhardness of
Cr coating was about 920 Hv which was higher than Co-Cr and even
Co-Cr/TiO2 films. Microhardness of Co-Cr and Co-Cr/TiO2 coatings
were improved by increasing their Cr and TiO2 content. All the
coatings had nodular morphology and contained microcracks.
Nodules sizes and the number of microcracks in the alloy and
composite coatings were lower than the Cr film. Wear results
revealed that the Co-Cr/TiO2 coating had the lowest wear loss
between all the samples, while the Cr film had the worst wear
resistance.
Abstract: The comprehensive CFD models have been used to
represent and study the heterogeneous combustion of biomass. In the
present work, the operation of a global flue gas circuit in the sugarcane
bagasse combustion, from wind boxes below primary air grate
supply, passing by bagasse insertion in swirl burners and boiler
furnace, to boiler bank outlet is simulated. It uses five different
meshes representing each part of this system located in sequence:
wind boxes and grate, boiler furnace, swirl burners, superheaters and
boiler bank. The model considers turbulence using standard k-ε,
combustion using EDM, radiation heat transfer using DTM with 16
ray directions and bagasse particle tracking represented by Schiller-
Naumann model. The results showed good agreement with expected
behavior found in literature and equipment design. The more detailed
results view in separated parts of flue gas system allows observing
some flow behaviors that cannot be represented by usual
simplifications like bagasse supply under homogeneous axial and
rotational vectors and others that can be represented using new
considerations like the representation of 26 thousand grate orifices by
144 rectangular inlets.