Abstract: The use of solar control film on windows as one of
solar passive strategies for building have becoming important and is
gaining recognition. Malaysia located close to equator is having
warm humid climate with long sunshine hours and abundant solar
radiation throughout the year. Hence, befitting solar control on
windows is absolutely necessary to capture the daylight whilst
moderating thermal impact and eliminating glare problems. This is
one of the energy efficient strategies to achieve thermal and visual
comfort in buildings. Therefore, this study was carried out to
investigate the effect of window solar controls on thermal and visual
performance of naturally ventilated buildings. This was conducted via
field data monitoring using a test building facility. Four types of
window glazing systems were used with three types of solar control
films. Data were analysed for thermal and visual impact with
reference to thermal and optical characteristics of the films. Results
show that for each glazing system, the surface temperature of
windows are influenced by the Solar Energy Absorption property, the
indoor air temperature are influenced by the Solar Energy
Transmittance and Solar Energy Reflectance, and the daylighting by
Visible Light Transmission and Shading Coefficient. Further
investigations are underway to determine the mathematical relation
between thermal energy and visual performance with the thermal and
optical characteristics of solar control films.
Abstract: Effect of temperature and light was investigated on a
thin film of organic semiconductor formyl-TIPPCu(II) deposited on a
glass substrate with preliminary evaporated gold electrodes. The
electrical capacitance and resistance of the fabricated device were
evaluated under the effect of temperature and light. The relative
capacitance of the fabricated sensor increased by 4.3 times by rising
temperature from 27 to 1870C, while under illumination up to 25000
lx, the capacitance of the Au/formyl-TIPPCu(II)/Au photo capacitive
sensor increased continuously by 13.2 times as compared to dark
conditions.
Abstract: Measurements of radioactivity in the environment is of great importance to monitor and control the levels of radiation to which man is exposed directly or indirectly. It is necessary to show that regardless of working or being close to nuclear power plants, people are daily in contact with some amount of radiation from the actual environment and food that are ingested, contradicting the view of most of them. The aim of this study was to analyze the rate of natural and artificial radiation from radionuclides present in cement, soil and fertilizers used in Sergipe State – Brazil. The radionuclide activitiesmeasured all samples arebelow the Brazilian limit of the exclusion and exemption criteria from the requirement of radiation protection.It was detected Be-7 in organic fertilizers that means a short interval between the brewing processes for use in agriculture. It was also detected an unexpected Cs-137 in some samples; however its activities does not represent risk for the population. Th-231 was also found in samples of soil and cement in the state of Sergipe that is an unprecedented result.
Abstract: A multi fingered dexterous anthropomorphic hand is
being developed by the authors. The focus of the hand is the
replacement of human operators in hazardous environments and also
in environments where zero tolerance is observed for the human
errors. The robotic hand will comprise of five fingers (four fingers
and one thumb) each having four degrees of freedom (DOF) which
can perform flexion, extension, abduction, adduction and also
circumduction. For the actuation purpose pneumatic muscles and
springs will be used. The paper exemplifies the mechanical design for
the robotic hand. It also describes different mechanical designs that
have been developed before date.
Abstract: In this work, we present a novel active learning approach
for learning a visual object detection system. Our system
is composed of an active learning mechanism as wrapper around
a sub-algorithm which implement an online boosting-based learning
object detector. In the core is a combination of a bootstrap procedure
and a semi automatic learning process based on the online boosting
procedure. The idea is to exploit the availability of classifier during
learning to automatically label training samples and increasingly
improves the classifier. This addresses the issue of reducing labeling
effort meanwhile obtain better performance. In addition, we propose
a verification process for further improvement of the classifier.
The idea is to allow re-update on seen data during learning for
stabilizing the detector. The main contribution of this empirical study
is a demonstration that active learning based on an online boosting
approach trained in this manner can achieve results comparable or
even outperform a framework trained in conventional manner using
much more labeling effort. Empirical experiments on challenging data
set for specific object deteciton problems show the effectiveness of
our approach.
Abstract: In this study, a classification-based video
super-resolution method using artificial neural network (ANN) is
proposed to enhance low-resolution (LR) to high-resolution (HR)
frames. The proposed method consists of four main steps:
classification, motion-trace volume collection, temporal adjustment,
and ANN prediction. A classifier is designed based on the edge
properties of a pixel in the LR frame to identify the spatial information.
To exploit the spatio-temporal information, a motion-trace volume is
collected using motion estimation, which can eliminate unfathomable
object motion in the LR frames. In addition, temporal lateral process is
employed for volume adjustment to reduce unnecessary temporal
features. Finally, ANN is applied to each class to learn the complicated
spatio-temporal relationship between LR and HR frames. Simulation
results show that the proposed method successfully improves both
peak signal-to-noise ratio and perceptual quality.
Abstract: In this study, to accurately predict cavitation of a
centrifugal pump, numerical analysis was compared with experimental
results modeled on a small industrial centrifugal pump. In this study,
numerical analysis was compared with experimental results modeled
on a small industrial centrifugal pump for reliable prediction on
cavitation of a centrifugal pump. To improve validity of the numerical
analysis, transient analysis was conducted on the calculated domain of
full-type geometry, such as an experimental apparatus. The numerical
analysis from the results was considered to be a reliable prediction of
cavitaion.
Abstract: Direct Torque Control is a control technique in AC
drive systems to obtain high performance torque control. The
conventional DTC drive contains a pair of hysteresis comparators.
DTC drives utilizing hysteresis comparators suffer from high torque
ripple and variable switching frequency. The most common solution
to those problems is to use the space vector depends on the reference
torque and flux. In this Paper The space vector modulation technique
(SVPWM) is applied to 2 level inverter control in the proposed
DTC-based induction motor drive system, thereby dramatically
reducing the torque ripple. Then the controller based on space vector
modulation is designed to be applied in the control of Induction
Motor (IM) with a three-level Inverter. This type of Inverter has
several advantages over the standard two-level VSI, such as a greater
number of levels in the output voltage waveforms, Lower dV/dt, less
harmonic distortion in voltage and current waveforms and lower
switching frequencies. This paper proposes a general SVPWM
algorithm for three-level based on standard two-level SVPWM. The
proposed scheme is described clearly and simulation results are
reported to demonstrate its effectiveness. The entire control scheme is
implemented with Matlab/Simulink.
Abstract: Glazing is a process used to reduce undesirable drying or dehydration of fish during frozen or cold storage. To evaluate the effect of the time/ temperature binomial of the cryogenic frozen tunnel in the amount of glazing watera Central Composite Rotatable Design was used, with application of the Response Surface Methodology. The results reveal that the time/ temperature obtained for pink cusk-eel in experimental conditions for glazing water are similar to the industrial process, but for red fish and merluza the industrial process needs some adjustments. Control charts were established and implementedto control the amount of glazing water on sardine and merluza. They show that the freezing process was statistically controlled but there were some tendencies that must be analyzed, since the trend of sample mean values approached either of the limits, mainly in merluza. Thus, appropriate actions must be taken, in order to improve the process.
Abstract: The aim of this study was to investigate whether
magnetite nanoparticles affect the viability of Bradyrhizobium
japanicum cells residing on the surface of soybean seeds during
desiccation. Different concentrations of nanoparticles suspended in
liquid medium, mixed with and adhering to Bradyrhizobium
japanicum, were investigated at two temperatures, using both
soybean seeds and glass beads as surrogates. Statistical design was a
complete randomized block (CRB) in a factorial 6×2×2×6
experimental arrangement with four replications. The most important
variable was the viability of Bradyrhizobium on the surface of the
seeds. The nanoparticles increased Bradyrhizobium viability and
inoculated seeds stored at low temperature had greater viability when
nanoparticles had been added. At the optimum nanoparticle
concentration, 50% bacterium viability on the seeds was retained
after 5 days at 4ºC. Possible explanations for the observed effects are
proposed.
Abstract: The combustion chamber dimensions have important
effects on pollutant emission in furnaces as a direct result of
temperature distribution and maximum temperature value. In this
paper the pollutant emission and the temperature distribution in two
cylindrical furnaces with different dimensions (with similar length to
diameter ratio) in similar condition have been investigated
experimentally. The furnace fuel is gas oil that is used with three
different flow rates. The results show that in these two cases the
temperature increases to its maximum value quickly, and then
decreases slowly. The results also show that increase in fuel flow rate
cause to increase in NOx emission in each case, but this increase is
greater in small furnace. With increase in fuel flow rate, CO emission
decreases firstly, and then it increases. Combustion efficiency
reduces with increase in fuel flow rate but the rate of reduction in
small furnace is greater than large furnace. The results of axial
temperature distribution have been compared with those have been
obtained numerically and experimentally by Moghiman.
Abstract: Radiolabeled cyclic RGD peptides targeting integrin αvβ3 are reported as promising agents for the early diagnosis of metastatic tumors. With an aim to improve tumor uptake and retention of the peptide, cyclic RGD peptide dimer E[c (RGDfK)] 2 (E = Glutamic acid, f = phenyl alanine, K = lysine) coupled to the bifunctional chelator DOTA was custom synthesized and radiolabelled with 68Ga. Radiolabelling of cyclic RGD peptide dimer with 68Ga was carried out using HEPES buffer and biological evaluation of the complex was done in nude mice bearing HT29 tumors.
Abstract: Reverse Engineering is a very important process in
Software Engineering. It can be performed backwards from system
development life cycle (SDLC) in order to get back the source data
or representations of a system through analysis of its structure,
function and operation. We use reverse engineering to introduce an
automatic tool to generate system requirements from its program
source codes. The tool is able to accept the Cµ programming source
codes, scan the source codes line by line and parse the codes to
parser. Then, the engine of the tool will be able to generate system
requirements for that specific program to facilitate reuse and
enhancement of the program. The purpose of producing the tool is to
help recovering the system requirements of any system when the
system requirements document (SRD) does not exist due to
undocumented support of the system.
Abstract: Wind catchers are traditional natural ventilation
systems attached to buildings in order to ventilate the indoor air. The
most common type of wind catcher is four sided one which is
capable to catch wind in all directions. CFD simulation is the perfect
way to evaluate the wind catcher performance. The accuracy of CFD
results is the issue of concern, so sensitivity analyses is crucial to
find out the effect of different settings of CFD on results. This paper
presents a series of 3D steady RANS simulations for a generic
isolated four-sided wind catcher attached to a room subjected to wind
direction ranging from 0º to 180º with an interval of 45º. The CFD
simulations are validated with detailed wind tunnel experiments. The
influence of an extensive range of computational parameters is
explored in this paper, including the resolution of the computational
grid, the size of the computational domain and the turbulence model.
This study found that CFD simulation is a reliable method for wind
catcher study, but it is less accurate in prediction of models with non
perpendicular wind directions.
Abstract: In this paper, a novel method for a biometric system based on the ECG signal is proposed, using spectral coefficients computed through linear predictive coding (LPC). ECG biometric systems have traditionally incorporated characteristics of fiducial points of the ECG signal as the feature set. These systems have been shown to contain loopholes and thus a non-fiducial system allows for tighter security. In the proposed system, incorporating non-fiducial features from the LPC spectrum produced a segment and subject recognition rate of 99.52% and 100% respectively. The recognition rates outperformed the biometric system that is based on the wavelet packet decomposition (WPD) algorithm in terms of recognition rates and computation time. This allows for LPC to be used in a practical ECG biometric system that requires fast, stringent and accurate recognition.
Abstract: Turbulent heat transfer to fluid flow through channel with triangular ribs of different angles are presented in this paper. Ansys 14 ICEM and Ansys 14 Fluent are used for meshing process and solving Navier stokes equations respectively. In this investigation three angles of triangular ribs with the range of Reynolds number varied from 20000 to 60000 at constant surface temperature are considered. The results show that the Nusselt number increases with the increase of Reynolds number for all cases at constant surface temperature. According to the profile of local Nusselt number on ribs walled of channel, the peak is at the midpoint between the two ribs. The maximum value of average Nusselt number is obtained for triangular ribs of angel 60°and at Reynolds number of 60000 compared to the Nusselt number for the ribs of angel 90° and 45° and at same Reynolds number. The recirculation regions generated by the ribs corresponding to the velocity streamline show the largest recirculation region at triangular ribs of angle 60° which also provides the highest enhancement of heat transfer.
Abstract: Seasonal variability of nutrients concentration in the Baltic Sea using the 3D ecosystem numerical model 3D-CEMBS has been investigated. Additionally this study shows horizontal and vertical distribution of nutrients in the Baltic Sea. Model domain is an extended Baltic Sea area divided into 600x640 horizontal grid cells. Aside from standard hydrodynamic parameters 3D-CEMBS produces modeled ecological variables such as: three types of phytoplankton, two detrital classes, dissolved oxygen and the nutrients (nitrate, ammonium, phosphate and silicate). The presented model allows prediction of parameters that describe distribution of nutrients concentration and phytoplankton biomass. 3D-CEMBS can be used to study the effect of different hydrodynamic and biogeochemical processes on distributions of these variables in a larger scale.
Abstract: In this paper, a two-dimensional mathematical model is developed for estimating the extent of inland inundation due to Indonesian tsunami of 2004 along the coastal belts of Peninsular Malaysia and Thailand. The model consists of the shallow water equations together with open and coastal boundary conditions. In order to route the water wave towards the land, the coastal boundary is treated as a time dependent moving boundary. For computation of tsunami inundation, the initial tsunami wave is generated in the deep ocean with the strength of the Indonesian tsunami of 2004. Several numerical experiments are carried out by changing the slope of the beach to examine the extent of inundation with slope. The simulated inundation is found to decrease with the increase of the slope of the orography. Correlation between inundation / recession and run-up are found to be directly proportional to each other.
Abstract: Streamribbon is used to visualize the rotation of the
fluid flow. The rotation of flow is useful in fluid mechanics,
engineering and geophysics. This paper introduces the construction
technique of streamribbon using the streamline which is generated
based on the law of mass conservation. The accuracy of constructed
streamribbons is shown through two examples.
Abstract: In this paper, an artificial neural network simulator is
employed to carry out diagnosis and prognosis on electric motor as
rotating machinery based on predictive maintenance. Vibration data
of the primary failed motor including unbalance, misalignment and
bearing fault were collected for training the neural network. Neural
network training was performed for a variety of inputs and the motor
condition was used as the expert training information. The main
purpose of applying the neural network as an expert system was to
detect the type of failure and applying preventive maintenance. The
advantage of this study is for machinery Industries by providing
appropriate maintenance that has an essential activity to keep the
production process going at all processes in the machinery industry.
Proper maintenance is pivotal in order to prevent the possible failures
in operating system and increase the availability and effectiveness of
a system by analyzing vibration monitoring and developing expert
system.