Abstract: The key role in phenomenological modelling of cyclic
plasticity is good understanding of stress-strain behaviour of given
material. There are many models describing behaviour of materials
using numerous parameters and constants. Combination of individual
parameters in those material models significantly determines whether
observed and predicted results are in compliance. Parameter
identification techniques such as random gradient, genetic algorithm
and sensitivity analysis are used for identification of parameters using
numerical modelling and simulation. In this paper genetic algorithm
and sensitivity analysis are used to study effect of 4 parameters of
modified AbdelKarim-Ohno cyclic plasticity model. Results
predicted by Finite Element (FE) simulation are compared with
experimental data from biaxial ratcheting test with semi-elliptical
loading path.
Abstract: This paper reports the numerical simulation of doublediffusive
natural convection flows within a horizontal annular filled
with a saturated porous medium. The analysis concerns the influence
of the different parameters governing the problem, namely, the
Rayleigh number Ra, the Lewis number Le and the buoyancy ratio N,
on the heat and mass transfer and on the flow structure, in the case of
a fixed radius ratio R = 2. The numerical model used for the
discretization of the dimensionless equations governing the problem
is based on the finite difference method, using the ADI scheme. The
study is focused on steady-state solutions in the cooperation situation.
Abstract: In Jordan having deficit atmospheric precipitation, an
increase in water demand occurs during summer months. Jordan can
be regarded with a relatively high potential for wastewater recycling
and reuse. The main purpose of this paper was to investigate the
removal of total suspended solids (TSS) and chemical oxygen
demand (COD) for olive mill wastewater (OMW) by
electrocoagulation (EC) process. In the combination of
electrocoagulation by using coupled iron–aluminum electrodes, the
optimum working pH was found to be around 6. Results indicated
that the electrocoagulation process allowed removal of TSS and COD
of about 82.5% and 47.5%, respectively at 45 mA/cm2 after 70
minutes by using coupled iron–aluminum electrodes. It was
demonstrated that the maximum TSS and COD removals were
obtained at some optimum experimental parameters for current
density, pH, and reaction time.
Abstract: The effects of hypertension are often lethal thus its
early detection and prevention is very important for everybody. In
this paper, a neural network (NN) model was developed and trained
based on a dataset of hypertension causative parameters in order to
forecast the likelihood of occurrence of hypertension in patients. Our
research goal was to analyze the potential of the presented NN to
predict, for a period of time, the risk of hypertension or the risk of
developing this disease for patients that are or not currently
hypertensive. The results of the analysis for a given patient can
support doctors in taking pro-active measures for averting the
occurrence of hypertension such as recommendations regarding the
patient behavior in order to lower his hypertension risk. Moreover,
the paper envisages a set of three example scenarios in order to
determine the age when the patient becomes hypertensive, i.e.
determine the threshold for hypertensive age, to analyze what
happens if the threshold hypertensive age is set to a certain age and
the weight of the patient if being varied, and, to set the ideal weight
for the patient and analyze what happens with the threshold of
hypertensive age.
Abstract: There is a trend in development discourse to
understand and explain the level of corruption in Nigeria, its anticorruption
crusade and why it is failing, as well as its level of
compliance with International standards of United Nations
Convention against Corruption (UNCAC) & African Union
Convention on Converting and Preventing Corruption) to which
Nigeria is a signatory. This paper discusses the legal and
Constitutional provisions relating to corrupt practices and safeguards
in Nigeria, as well as the obstacles to the implementation of these
Conventions.
The paper highlights the challenges posed to the Anti-Corruption
crusade by analysing the loopholes that exist both in administrative
structure and in scope of the relevant laws. The paper argues that
Nigerian Constitution did not make adequate provisions for the
implementation of the conventions, hence a proposal which will
ensure adequate provision for implementing the conventions to better
the lives of Nigerians. The paper concludes that there is the need to
build institutional parameters, adequate constitutional and structural
safeguards, as well as to synergise strategies, collaborations and
alliances to facilitate the timely domestication and implementation of
the conventions.
Abstract: Two finite element (FEM) models are presented in
this paper to address the random nature of the response of glued
timber structures made of wood segments with variable elastic
moduli evaluated from 3600 indentation measurements. This total
database served to create the same number of ensembles as was the
number of segments in the tested beam. Statistics of these ensembles
were then assigned to given segments of beams and the Latin
Hypercube Sampling (LHS) method was called to perform 100
simulations resulting into the ensemble of 100 deflections subjected
to statistical evaluation. Here, a detailed geometrical arrangement of
individual segments in the laminated beam was considered in the
construction of two-dimensional FEM model subjected to in fourpoint
bending to comply with the laboratory tests. Since laboratory
measurements of local elastic moduli may in general suffer from a
significant experimental error, it appears advantageous to exploit the
full scale measurements of timber beams, i.e. deflections, to improve
their prior distributions with the help of the Bayesian statistical
method. This, however, requires an efficient computational model
when simulating the laboratory tests numerically. To this end, a
simplified model based on Mindlin’s beam theory was established.
The improved posterior distributions show that the most significant
change of the Young’s modulus distribution takes place in laminae in
the most strained zones, i.e. in the top and bottom layers within the
beam center region. Posterior distributions of moduli of elasticity
were subsequently utilized in the 2D FEM model and compared with
the original simulations.
Abstract: An experimental study was performed to investigate
the behavior and strength of proposed technique to connect
reinforced concrete (RC) beam to steel or composite columns. This
approach can practically be used in several types of building
construction. In this technique, the main beam of the frame consists
of a transfer part (part of beam; Tr.P) and a common reinforcement
concrete beam. The transfer part of the beam is connected to the
column, whereas the rest of the beam is connected to the transfer part
from each side. Four full-scale beam-column connections were tested
under static loading. The test parameters were the length of the
transfer part and the column properties. The test results show that
using of the transfer part technique leads to modify the deformation
capabilities for the RC beam and hence it increases its resistance
against failure. Increase in length of the transfer part did not
necessarily indicate an enhanced behavior. The test results contribute
to the characterization of the connection behavior between RC beam -
steel column and can be used to calibrate numerical models for the
simulation of this type of connection.
Abstract: To determine the potential of a low cost Irish
engineered timber product to replace high cost solid timber for use in
bending active structures such as gridshells a single Irish engineered
timber product in the form of orientated strand board (OSB) was
selected. A comparative study of OSB and solid timber was carried
out to determine the optimum properties that make a material suitable
for use in gridshells. Three parameters were identified to be relevant
in the selection of a material for gridshells. These three parameters
are the strength to stiffness ratio, the flexural stiffness of
commercially available sections, and the variability of material and
section properties. It is shown that when comparing OSB against
solid timber, OSB is a more suitable material for use in gridshells that
are at the smaller end of the scale and that have tight radii of
curvature. Typically, for solid timber materials, stiffness is used as an
indicator for strength and engineered timber is no different. Thus, low
flexural stiffness would mean low flexural strength. However, when
it comes to bending active gridshells, OSB offers a significant
advantage. By the addition of multiple layers, an increased section
size is created, thus endowing the structure with higher stiffness and
higher strength from initial low stiffness and low strength materials
while still maintaining tight radii of curvature. This allows OSB to
compete with solid timber on large scale gridshells. Additionally, a
preliminary sustainability study using a set of sustainability indicators
was carried out to determine the relative sustainability of building a
large-scale gridshell in Ireland with a primary focus on economic
viability but a mention is also given to social and environmental
aspects. For this, the Savill garden gridshell in the UK was used as
the functional unit with the sustainability of the structural roof
skeleton constructed from UK larch solid timber being compared
with the same structure using Irish OSB. Albeit that the advantages of
using commercially available OSB in a bending active gridshell are
marginal and limited to specific gridshell applications, further study
into an optimised engineered timber product is merited.
Abstract: This paper proposes five level diode clamped Z source
Inverter. The existing PWM techniques used for ZSI are restricted for
two level. The two level Z Source Inverter have high harmonic
distortions which effects the performance of the grid connected PV
system. To improve the performance of the system the number of
voltage levels in the output waveform need to be increased. This
paper presents comparative analysis of a five level diode clamped Z
source Inverter with different carrier based Modified Pulse Width
Modulation techniques. The parameters considered for comparison
are output voltage, voltage gain, voltage stress across switch and total
harmonic distortion when powered by same DC supply. Analytical
results are verified using MATLAB.
Abstract: Most people today are aware that global climate
change is not just a scientific theory but also a fact with worldwide
consequences. Global climate change is due to rapid urbanization,
industrialization, high population growth and current vulnerability of
the climatic condition. Water is becoming scarce as a result of global
climate change. To mitigate the problem arising due to global climate
change and its drought effect, harvesting rainwater from green roofs,
an environmentally-friendly and versatile technology, is becoming
one of the best assessment criteria and gaining attention in Malaysia.
This paper addresses the sustainability of green roofs and examines
the quality of water harvested from green roofs in comparison to
rainwater. The factors that affect the quality of such water, taking
into account, for example, roofing materials, climatic conditions, the
frequency of rainfall frequency and the first flush. A green roof was
installed on the Humid Tropic Centre (HTC) is a place of the study
on monitoring program for urban Stormwater Management Manual
for Malaysia (MSMA), Eco-Hydrological Project in Kuala Lumpur,
and the rainwater was harvested and evaluated on the basis of four
parameters i.e., conductivity, dissolved oxygen (DO), pH and
temperature. These parameters were found to fall between Class I and
Class III of the Interim National Water Quality Standards (INWQS)
and the Water Quality Index (WQI). Some preliminary treatment
such as disinfection and filtration could likely to improve the value of
these parameters to class I. This review paper clearly indicates that
there is a need for more research to address other microbiological and
chemical quality parameters to ensure that the harvested water is
suitable for use potable water for domestic purposes. The change in
all physical, chemical and microbiological parameters with respect to
storage time will be a major focus of future studies in this field.
Abstract: The check-in area of airport terminal is one of the
busiest sections at airports at certain periods. The passengers are
subjected to queues and delays during the check-in process. These
delays and queues are due to constraints in the capacity of service
facilities. In this project, the airport terminal is decomposed into
several check-in areas. The airport check-in scheduling problem
requires both a deterministic (integer programming) and stochastic
(simulation) approach. Integer programming formulations are
provided to minimize the total number of counters in each check-in
area under the realistic constraint that counters for one and the same
flight should be adjacent and the desired number of counters
remaining in each area should be fixed during check-in operations.
By using simulation, the airport system can be modeled to study the
effects of various parameters such as number of passengers on a
flight and check-in counter opening and closing time.
Abstract: The Al-MoO3-P-CdTe-Al MOS sandwich structures
were fabricated by vacuum deposition method on cleaned glass
substrates. Capacitance versus voltage measurements were performed
at different frequencies and sweep rates of applied voltages for oxide
and semiconductor films of different thicknesses. In the negative
voltage region of the C-V curve a high differential capacitance of the
semiconductor was observed and at high frequencies (
Abstract: Chemical vapor deposition (CVD) diamond coated
cutting tool has excellent cutting performance, it is the most ideal tool
for the processing of nonferrous metals and alloys, composites,
nonmetallic materials and other difficult-to-machine materials
efficiently and accurately. Depositing CVD diamond coating on the
cemented carbide with high cobalt content can improve its toughness
and strength, therefore, it is very important to research on the
preparation technology and cutting properties of CVD diamond coated
cemented carbide cutting tool with high cobalt content. The
preparation technology of boron-doped diamond (BDD) coating has
been studied and the coated drills were prepared. BDD coating were
deposited on the drills by using the optimized parameters and the SEM
results show that there are no cracks or collapses in the coating.
Cutting tests with the prepared drills against the silumin and aluminum
base printed circuit board (PCB) have been studied. The results show
that the wear amount of the coated drill is small and the machined
surface has a better precision. The coating does not come off during
the test, which shows good adhesion and cutting performance of the
drill.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. This paper describes experimental
investigation on the response of new advanced materials to low and
high velocity load. Blast wave energy absorbers were designed using
two types of porous lightweight raw particle materials based on
expanded glass and ceramics with dimensions of 0.5-1 mm,
combined with polymeric binder. The effect of binder amount on the
static and dynamic properties of designed materials was observed.
Prism shaped specimens were prepared and loaded to obtain physicomechanical
parameters – bulk density, compressive and flexural
strength under quasistatic load, the dynamic response was determined
using Split Hopkinson Pressure bar apparatus. Numerical
investigation of the material behaviour in sandwich structure was
performed using implicit/explicit solver LS-Dyna. As the last step,
the developed material was used as the interlayer of blast resistant
litter bin, and it´s functionality was verified by real field blast tests.
Abstract: In this paper we consider the equation of motion for
the F (R, T) gravity on their property of conformal invariance. It
is shown that in the general case, such a theory is not conformal
invariant. Studied special cases for the functions v and u in which
can appear properties of the theory. Also we consider cosmological
aspects F (R, T) theory of gravity, having considered particular case
F (R, T) = μR+νT^2. Showed that in this case there is a nonlinear
dependence of the parameter equation of state from time to time,
which affects its evolution.
Abstract: The present work describes the implementation of the
Enhanced Collaborative Optimization (ECO) multilevel architecture
with a gradient-based optimization algorithm with the aim of
performing a multidisciplinary design optimization of a generic
unmanned aerial vehicle with morphing technologies. The concepts
of weighting coefficient and dynamic compatibility parameter are
presented for the ECO architecture. A routine that calculates the
aircraft performance for the user defined mission profile and vehicle’s
performance requirements has been implemented using low fidelity
models for the aerodynamics, stability, propulsion, weight, balance
and flight performance. A benchmarking case study for evaluating
the advantage of using a variable span wing within the optimization
methodology developed is presented.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of ellipsoidal cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
ellipsoidal cross section by taking into account of the porosity factor
of the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter and
the porosity parameter of the bounding surface has significant effect
on the velocity parameter.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: Comparing other methods of waste water treatment,
constructed wetlands are one of the most fascinating practices
because being a natural process they are eco-friendly have low
construction and maintenance cost and have considerable capability
of wastewater treatment. The current research was focused mainly on
comparison of Ranunculus muricatus and Typha latifolia as wetland
plants for domestic wastewater treatment by designing and
constructing efficient pilot scale horizontal subsurface flow
mesocosms. Parameters like chemical oxygen demand, biological
oxygen demand, phosphates, sulphates, nitrites, nitrates, and
pathogenic indicator microbes were studied continuously with
successive treatments. Treatment efficiency of the system increases
with passage of time and with increase in temperature. Efficiency of
T. latifolia planted setups in open environment was fairly good for
parameters like COD and BOD5 which was showing reduction up to
82.5% for COD and 82.6% for BOD5 while DO was increased up to
125%. Efficiency of R. muricatus vegetated setup was also good but
lowers than that of T. latifolia planted showing 80.95% removal of
COD and BOD5. Ranunculus muricatus was found effective in
reducing bacterial count in wastewater. Both macrophytes were
found promising in wastewater treatment.
Abstract: Cemented carbide balls are usually implemented in
industry under the environment of high speed, high temperature,
corrosiveness and strong collisions. However, its application is limited
due to high fabrication cost, processing efficiency and quality. A novel
eccentric lapping method with two rotatable lapping plates was
proposed in this paper. A mathematical model was constructed to
analyze the influence of each design parameter on this lapping method.
To validate this new lapping method, an orthogonal experiment was
conducted with cemented carbide balls (YG6). The simulation model
was verified and the optimal lapping parameters were derived. The
results show that the surface roundness of the balls reaches to 0.65um
from 2um in 1 hour using this lapping method. So, using this novel
lapping method, it can effectively improve the machining precision
and efficiency of cemented carbide balls.