Abstract: A simple adaptive voice activity detector (VAD) is
implemented using Gabor and gammatone atomic decomposition of
speech for high Gaussian noise environments. Matching pursuit is
used for atomic decomposition, and is shown to achieve optimal
speech detection capability at high data compression rates for low
signal to noise ratios. The most active dictionary elements found by
matching pursuit are used for the signal reconstruction so that the
algorithm adapts to the individual speakers dominant time-frequency
characteristics. Speech has a high peak to average ratio enabling
matching pursuit greedy heuristic of highest inner products to isolate
high energy speech components in high noise environments. Gabor
and gammatone atoms are both investigated with identical
logarithmically spaced center frequencies, and similar bandwidths.
The algorithm performs equally well for both Gabor and gammatone
atoms with no significant statistical differences. The algorithm
achieves 70% accuracy at a 0 dB SNR, 90% accuracy at a 5 dB SNR
and 98% accuracy at a 20dB SNR using 30d B SNR as a reference
for voice activity.
Abstract: The atmospheres in many cities along the coastal lines
in the world have been rapidly changed to coastal-industrial
atmosphere. Hence, it is vital to investigate the corrosion behavior of
steel exposed to this kind of environment. In this present study,
Electrochemical Impedance Spectrography (EIS) and film thickness
measurement were applied to monitor the corrosion behavior of
weathering steel covered with a thin layer of the electrolyte in a
wet-dry cyclic condition, simulating a coastal-industrial environment
at 25oC and 60% RH. The results indicate that in all cycles, the
corrosion rate increases during the drying process due to an increase in
anion concentration and an acceleration of oxygen diffusion enhanced
by the effect of the thinning out of the electrolyte. During the wet-dry
cyclic corrosion test, the long-term corrosion behavior of this steel
depends on the periods of exposure. Corrosion process is first
accelerated and then decelerated. The decelerating corrosion process is
contributed to the formation of the protective rust, favored by the
wet-dry cycle and the acid regeneration process during the rusting
process.
Abstract: Prosperity of electronic equipment in photocopying
environment not only has improved work efficiency, but also has
changed indoor air quality. Considering the number of photocopying
employed, indoor air quality might be worse than in general office
environments. Determining the contribution from any type of
equipment to indoor air pollution is a complex matter. Non-methane
hydrocarbons are known to have an important role on air quality due
to their high reactivity. The presence of hazardous pollutants in
indoor air has been detected in one photocopying shop in Novi Sad,
Serbia. Air samples were collected and analyzed for five days, during
8-hr working time in three time intervals, whereas three different
sampling points were determined. Using multiple linear regression
model and software package STATISTICA 10 the concentrations of
occupational hazards and microclimates parameters were mutually
correlated. Based on the obtained multiple coefficients of
determination (0.3751, 0.2389 and 0.1975), a weak positive
correlation between the observed variables was determined. Small
values of parameter F indicated that there was no statistically
significant difference between the concentration levels of nonmethane
hydrocarbons and microclimates parameters. The results
showed that variable could be presented by the general regression
model: y = b0 + b1xi1+ b2xi2. Obtained regression equations allow to
measure the quantitative agreement between the variables and thus
obtain more accurate knowledge of their mutual relations.
Abstract: High density electrical prospecting has been widely
used in groundwater investigation, civil engineering and
environmental survey. For efficient inversion, the forward modeling
routine, sensitivity calculation, and inversion algorithm must be
efficient. This paper attempts to provide a brief summary of the past
and ongoing developments of the method. It includes reviews of the
procedures used for data acquisition, processing and inversion of
electrical resistivity data based on compilation of academic literature.
In recent times there had been a significant evolution in field survey
designs and data inversion techniques for the resistivity method. In
general 2-D inversion for resistivity data is carried out using the
linearized least-square method with the local optimization technique
.Multi-electrode and multi-channel systems have made it possible to
conduct large 2-D, 3-D and even 4-D surveys efficiently to resolve
complex geological structures that were not possible with traditional
1-D surveys. 3-D surveys play an increasingly important role in very
complex areas where 2-D models suffer from artifacts due to off-line
structures. Continued developments in computation technology, as
well as fast data inversion techniques and software, have made it
possible to use optimization techniques to obtain model parameters to
a higher accuracy. A brief discussion on the limitations of the
electrical resistivity method has also been presented.
Abstract: Evolutionary optimization methods such as genetic
algorithms have been used extensively for the construction site layout
problem. More recently, ant colony optimization algorithms, which
are evolutionary methods based on the foraging behavior of ants,
have been successfully applied to benchmark combinatorial
optimization problems. This paper proposes a formulation of the site
layout problem in terms of a sequencing problem that is suitable for
solution using an ant colony optimization algorithm.
In the construction industry, site layout is a very important
planning problem. The objective of site layout is to position
temporary facilities both geographically and at the correct time such
that the construction work can be performed satisfactorily with
minimal costs and improved safety and working environment. During
the last decade, evolutionary methods such as genetic algorithms
have been used extensively for the construction site layout problem.
This paper proposes an ant colony optimization model for
construction site layout. A simple case study for a highway project is
utilized to illustrate the application of the model.
Abstract: OPEN_EmoRec_II is an open multimodal corpus with
experimentally induced emotions. In the first half of the experiment,
emotions were induced with standardized picture material and in the
second half during a human-computer interaction (HCI), realized
with a wizard-of-oz design. The induced emotions are based on the
dimensional theory of emotions (valence, arousal and dominance).
These emotional sequences - recorded with multimodal data (facial
reactions, speech, audio and physiological reactions) during a
naturalistic-like HCI-environment one can improve classification
methods on a multimodal level.
This database is the result of an HCI-experiment, for which 30
subjects in total agreed to a publication of their data including the
video material for research purposes*. The now available open
corpus contains sensory signal of: video, audio, physiology (SCL,
respiration, BVP, EMG Corrugator supercilii, EMG Zygomaticus
Major) and facial reactions annotations.
Abstract: OPEN_EmoRec_II is an open multimodal corpus with
experimentally induced emotions. In the first half of the experiment,
emotions were induced with standardized picture material and in the
second half during a human-computer interaction (HCI), realized
with a wizard-of-oz design. The induced emotions are based on the
dimensional theory of emotions (valence, arousal and dominance).
These emotional sequences - recorded with multimodal data (facial
reactions, speech, audio and physiological reactions) during a
naturalistic-like HCI-environment one can improve classification
methods on a multimodal level.
This database is the result of an HCI-experiment, for which 30
subjects in total agreed to a publication of their data including the
video material for research purposes*. The now available open
corpus contains sensory signal of: video, audio, physiology (SCL,
respiration, BVP, EMG Corrugator supercilii, EMG Zygomaticus
Major) and facial reactions annotations.
Abstract: Heat transfer of leaves is a crucial factor in optimal
operation of metabolic functions in plants. In order to quantify this
phenomenon in different leaves and investigate the influence of leaf
shape on heat transfer, natural convection for pine, orange and olive
leaves was simulated as representatives of different groups of leaf
shapes. CFD techniques were used in this simulation with the
purpose to calculate heat transfer of leaves in similar environmental
conditions. The problem was simulated for steady state and threedimensional
conditions. From obtained results, it was concluded that
heat fluxes of all three different leaves are almost identical, however,
total rate of heat transfer have highest and lowest values for orange
leaves, and pine leaves, respectively.
Abstract: Ibeno, Nigeria hosts the operational base of Mobil
Producing Nigeria Unlimited (MPNU), a subsidiary of ExxonMobil
and the current highest oil & condensate producer in Nigeria. Besides
MPNU, other oil companies operate onshore, on the continental shelf
and deep offshore of the Atlantic Ocean in Ibeno, Nigeria. This study
was designed to delineate oil polluted sites in Ibeno, Nigeria using
geophysical methods of electrical resistivity (ER) and ground
penetrating radar (GPR). Results obtained revealed that there have
been hydrocarbon contaminations of this environment by past crude
oil spills as observed from high resistivity values and GPR profiles
which clearly show the distribution, thickness and lateral extent of
hydrocarbon contamination as represented on the radargram reflector
tones. Contaminations were of varying degrees, ranging from slight
to high, indicating levels of substantial attenuation of crude oil
contamination over time. Moreover, the display of relatively lower
resistivities of locations outside the impacted areas compared to
resistivity values within the impacted areas and the 3-D Cartesian
images of oil contaminant plume depicted by red, light brown and
magenta for high, low and very low oil impacted areas, respectively
confirmed significant recent pollution of the study area with crude
oil.
Abstract: Pt/γ-Al2O3 membrane catalysts were prepared via an
evaporative-crystallization deposition method. The obtained Pt/γ-
Al2O3 catalyst activity was tested after characterization (SEM-EDAX
observation, BET measurement, permeability assessment) in the
catalytic oxidation of selected volatile organic compound (VOC) i.e.
propane, fed in mixture of oxygen. The VOC conversion (nearly
90%) obtained by varying the operating temperature showed that
flow-through membrane reactor might do better in the abatement of
VOCs.
Abstract: One of the key aspects of power quality improvement
in power system is the mitigation of voltage sags/swells and flicker.
Custom power devices have been known as the best tools for voltage
disturbances mitigation as well as reactive power compensation.
Dynamic Voltage Restorer (DVR) which is the most efficient and
effective modern custom power device can provide the most
commercial solution to solve several problems of power quality in
distribution networks. This paper deals with analysis and simulation
technique of DVR based on instantaneous power theory which is a
quick control to detect signals. The main purpose of this work is to
remove three important disturbances including voltage sags/swells
and flicker. Simulation of the proposed method was carried out on
two sample systems by using Matlab software environment and the
results of simulation show that the proposed method is able to
provide desirable power quality in the presence of wide range of
disturbances.
Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: Corrosion of concrete sewer pipes induced by
sulphuric acid attack is a recognised problem worldwide, which is not
only an attribute of countries with hot climate conditions as thought
before. The significance of this problem is by far only realised when
the pipe collapses causing surface flooding and other severe
consequences. To change the existing post-reactive attitude of
managing companies, easy to use and robust models are required to
be developed which currently lack reliable data to be correctly
calibrated. This paper focuses on laboratory experiments of
establishing concrete pipe corrosion rate by submerging samples in to
0.5pH sulphuric acid solution for 56 days under 10ºC, 20ºC and 30ºC
temperature regimes. The result showed that at very early stage of the
corrosion process the samples gained overall mass, at 30ºC the
corrosion progressed quicker than for other temperature regimes,
however with time the corrosion level for 10ºC and 20ºC regimes
tended towards those at 30ºC. Overall, at these conditions the
corrosion rates of 10 mm/year, 13,5 mm/year and 17 mm/year were
observed.
Abstract: Cloud computing is the innovative and leading
information technology model for enabling convenient, on-demand
network access to a shared pool of configurable computing resources
that can be rapidly provisioned and released with minimal
management effort. In this paper, we aim at the development of
workflow management system for cloud computing platforms based
on our previous research on the dynamic allocation of the cloud
computing resources and its workflow process. We took advantage of
the HTML5 technology and developed web-based workflow interface.
In order to enable the combination of many tasks running on the cloud
platform in sequence, we designed a mechanism and developed an
execution engine for workflow management on clouds. We also
established a prediction model which was integrated with job queuing
system to estimate the waiting time and cost of the individual tasks on
different computing nodes, therefore helping users achieve maximum
performance at lowest payment. This proposed effort has the potential
to positively provide an efficient, resilience and elastic environment
for cloud computing platform. This development also helps boost user
productivity by promoting a flexible workflow interface that lets users
design and control their tasks' flow from anywhere.
Abstract: Roadway planning and design is a very complex
process involving five key phases before a project is completed;
planning, project development, final design, right-of-way, and
construction. The planning phase for a new roadway transportation
project is a very critical phase as it greatly affects all latter phases of
the project. A location study is usually performed during the
preliminary planning phase in a new roadway project. The objective
of the location study is to develop alignment alternatives that are cost
efficient considering land acquisition and construction costs. This
paper describes a methodology to develop optimal preliminary
roadway alignments utilizing spatial-data. Four optimization criteria
are taken into consideration; roadway length, land cost, land slope,
and environmental impacts. The basic concept of the methodology is
to convert the proposed project area into a grid, which represents the
search space for an optimal alignment. The aforementioned
optimization criteria are represented in each of the grid’s cells. A
spatial-data optimization technique is utilized to find the optimal
alignment in the search space based on the four optimization criteria.
Two case studies for new roadway projects in Duval County in the
State of Florida are presented to illustrate the methodology. The
optimization output alignments are compared to the proposed Florida
Department of Transportation (FDOT) alignments. The comparison is
based on right-of-way costs for the alignments. For both case studies,
the right-of-way costs for the developed optimal alignments were
found to be significantly lower than the FDOT alignments.
Abstract: In today’s rapidly changing and increasingly complex
environment, organizations have relied on their members’ positive
attitude toward their employers. In particular, employees’
organizational commitment (primarily, the affective component) has
been recognized as an essential component of organizational
functioning and success. Hence, identifying the determinants of
affective commitment is one of the most important research issues.
This study tested the influence of leader-member exchange (LMX)
and exchange ideology on employee’s affective commitment. In
addition, the interactive effect of LMX and exchange ideology was
examined. Data from 198 members of the Korean military supports
each of the hypotheses. Lastly, implications for research and directions
for future research are discussed.
Abstract: During the post-Civil War era, the city of Nashville,
Tennessee, had the highest mortality rate in the United States. The
elevated death and disease rates among former slaves were
attributable to lack of quality healthcare. To address the paucity of
healthcare services, Meharry Medical College, an institution with the
mission of educating minority professionals and serving the
underserved population, was established in 1876.
Purpose: The social ecological framework and partial least squares
(PLS) path modeling were used to quantify the impact of
socioeconomic status and adverse health outcome on primary care
professionals serving the disadvantaged community. Thus, the study
results could demonstrate the accomplishment of the College’s
mission of training primary care professionals to serve in underserved
areas.
Methods: Various statistical methods were used to analyze alumni
data from 1975 – 2013. K-means cluster analysis was utilized to
identify individual medical and dental graduates in the cluster groups
of the practice communities (Disadvantaged or Non-disadvantaged
Communities). Discriminant analysis was implemented to verify the
classification accuracy of cluster analysis. The independent t-test was
performed to detect the significant mean differences of respective
clustering and criterion variables. Chi-square test was used to test if
the proportions of primary care and non-primary care specialists are
consistent with those of medical and dental graduates practicing in
the designated community clusters. Finally, the PLS path model was
constructed to explore the construct validity of analytic model by
providing the magnitude effects of socioeconomic status and adverse
health outcome on primary care professionals serving the
disadvantaged community.
Results: Approximately 83% (3,192/3,864) of Meharry Medical
College’s medical and dental graduates from 1975 to 2013 were
practicing in disadvantaged communities. Independent t-test confirmed the content validity of the cluster analysis model. Also, the
PLS path modeling demonstrated that alumni served as primary care
professionals in communities with significantly lower socioeconomic
status and higher adverse health outcome (p < .001). The PLS path
modeling exhibited the meaningful interrelation between primary
care professionals practicing communities and surrounding
environments (socioeconomic statues and adverse health outcome),
which yielded model reliability, validity, and applicability.
Conclusion: This study applied social ecological theory and
analytic modeling approaches to assess the attainment of Meharry
Medical College’s mission of training primary care professionals to
serve in underserved areas, particularly in communities with low
socioeconomic status and high rates of adverse health outcomes. In
summary, the majority of medical and dental graduates from Meharry
Medical College provided primary care services to disadvantaged
communities with low socioeconomic status and high adverse health
outcome, which demonstrated that Meharry Medical College has
fulfilled its mission. The high reliability, validity, and applicability of
this model imply that it could be replicated for comparable
universities and colleges elsewhere.
Abstract: This work sets out to debate the tensions involved in
the processes of contamination and self-purification in the urban
space, particularly in the streams that run through the Buenos Aires
metropolitan area. For much of their course, those streams are piped;
their waters do not come into contact with the outdoors until they
have reached deeply impoverished urban areas with high levels of
environmental contamination. These are peripheral zones that, until
thirty years ago, were marshlands and fields. They are now densely
populated areas largely lacking in urban infrastructure.
The Cárcova neighborhood, where this project is underway, is in
the José León Suárez section of General San Martín county, Buenos
Aires province. A stretch of José León Suarez canal crosses the
neighborhood. Starting upstream, this canal carries pollutants due to
the sewage and industrial waste released into it. Further downstream,
in the neighborhood, domestic drainage is poured into the stream. In
this paper, we formulate a hypothesis diametrical to the one that
holds that these neighborhoods are the primary source of
contamination, suggesting instead that in the stretch of the canal that
runs through the neighborhood the stream’s waters are actually
cleaned and the sediments accumulate pollutants. Indeed, the
stretches of water that runs through these neighborhoods act as water
processing plants for the metropolis.
This project has studied the different organic-load polluting
contributions to the water in a certain stretch of the canal, the
reduction of that load over the course of the canal, and the
incorporation of pollutants into the sediments. We have found that
the surface water has considerable ability to self-purify, mostly due to
processes of sedimentation and adsorption. The polluting load is
accumulated in the sediments where that load stabilizes slowly by
means of anaerobic processes. In this study, we also investigated the
risks of sediment management and the use of the processes studied
here in controlled conditions as tools of environmental restoration.
Abstract: Organizational tendencies towards computer-based
information processing have been observed noticeably in the
third-world countries. Many enterprises are taking major initiatives
towards computerized working environment because of massive
benefits of computer-based information processing. However,
designing and developing information resource management software
for small and mid-size enterprises under budget costs and strict
deadline is always challenging for software engineers. Therefore, we
introduced an approach to design mid-size enterprise software by
using the Waterfall model, which is one of the SDLC (Software
Development Life Cycles), in a cost effective way. To fulfill research
objectives, in this study, we developed mid-sized enterprise software
named “BSK Management System” that assists enterprise software
clients with information resource management and perform complex
organizational tasks. Waterfall model phases have been applied to
ensure that all functions, user requirements, strategic goals, and
objectives are met. In addition, Rich Picture, Structured English, and
Data Dictionary have been implemented and investigated properly in
engineering manner. Furthermore, an assessment survey with 20
participants has been conducted to investigate the usability and
performance of the proposed software. The survey results indicated
that our system featured simple interfaces, easy operation and
maintenance, quick processing, and reliable and accurate transactions.
Abstract: Proposed paper dealt with the modelling and analysis of induction motor based on the mathematical expression using the graphical programming environment of Laboratory Virtual Instrument Engineering Workbench (LabVIEW). Induction motor modelling with the mathematical expression enables the motor to be simulated with the various required parameters. Owing to the invention of variable speed drives study about the induction motor characteristics became complex. In this simulation motor internal parameter such as stator resistance and reactance, rotor resistance and reactance, phase voltage, frequency and losses will be given as input. By varying the speed of motor corresponding parameters can be obtained they are input power, output power, efficiency, torque induced, slip and current.