Abstract: Bicycle configuration is not as large as those of motorcycles or automobiles, while it indeed composes a complicated dynamic system. People-s requirements on comfortability, controllability and safety grow higher as the research and development technologies improve. The shock absorber affects the vehicle suspension performances enormously. The absorber takes the vibration energy and releases it at a suitable time, keeping the wheel under a proper contact condition with road surface, maintaining the vehicle chassis stability. Suspension design for mountain bicycles is more difficult than that of city bikes since it encounters dynamic variations on road and loading conditions. Riders need a stiff damper as they exert to tread on the pedals when climbing, while a soft damper when they descend downhill. Various switchable shock absorbers are proposed in markets, however riders have to manually switch them among soft, hard and lock positions. This study proposes a novel design of the bicycle shock absorber, which provides automatic smooth tuning of the damping coefficient, from a predetermined lower bound to theoretically unlimited. An automatic quick releasing valve is involved in this design so that it can release the peak pressure when the suspension fork runs into a square-wave type obstacle and prevent the chassis from damage, avoiding the rider skeleton from injury. This design achieves the automatic tuning process by innovative plunger valve and fluidic passage arrangements without any electronic devices. Theoretical modelling of the damper and spring are established in this study. Design parameters of the valves and fluidic passages are determined. Relations between design parameters and shock absorber performances are discussed in this paper. The analytical results give directions to the shock absorber manufacture.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: The uses of road map in daily activities are numerous
but it is a hassle to construct and update a road map whenever there
are changes. In Universiti Malaysia Sarawak, research on Automatic
Road Extraction (ARE) was explored to solve the difficulties in
updating road map. The research started with using Satellite Image
(SI), or in short, the ARE-SI project. A Hybrid Simple Colour Space
Segmentation & Edge Detection (Hybrid SCSS-EDGE) algorithm
was developed to extract roads automatically from satellite-taken
images. In order to extract the road network accurately, the satellite
image must be analyzed prior to the extraction process. The
characteristics of these elements are analyzed and consequently the
relationships among them are determined. In this study, the road
regions are extracted based on colour space elements and edge details
of roads. Besides, edge detection method is applied to further filter
out the non-road regions. The extracted road regions are validated by
using a segmentation method. These results are valuable for building
road map and detecting the changes of the existing road database.
The proposed Hybrid Simple Colour Space Segmentation and Edge
Detection (Hybrid SCSS-EDGE) algorithm can perform the tasks
fully automatic, where the user only needs to input a high-resolution
satellite image and wait for the result. Moreover, this system can
work on complex road network and generate the extraction result in
seconds.
Abstract: SQL injection on web applications is a very popular
kind of attack. There are mechanisms such as intrusion detection
systems in order to detect this attack. These strategies often rely on
techniques implemented at high layers of the application but do not
consider the low level of system calls. The problem of only
considering the high level perspective is that an attacker can
circumvent the detection tools using certain techniques such as URL
encoding. One technique currently used for detecting low-level
attacks on privileged processes is the tracing of system calls. System
calls act as a single gate to the Operating System (OS) kernel; they
allow catching the critical data at an appropriate level of detail. Our
basic assumption is that any type of application, be it a system
service, utility program or Web application, “speaks” the language of
system calls when having a conversation with the OS kernel. At this
level we can see the actual attack while it is happening. We conduct
an experiment in order to demonstrate the suitability of system call
analysis for detecting SQL injection. We are able to detect the attack.
Therefore we conclude that system calls are not only powerful in
detecting low-level attacks but that they also enable us to detect highlevel
attacks such as SQL injection.
Abstract: Intermittent aeration process can be easily applied on
the existing activated sludge system and is highly reliable against the loading changes. It can be operated in a relatively simple way as well.
Since the moving-bed biofilm reactor method processes pollutants by attaching and securing the microorganisms on the media, the process
efficiency can be higher compared to the suspended growth biological
treatment process, and can reduce the return of sludge. In this study,
the existing intermittent aeration process with alternating flow being
applied on the oxidation ditch is applied on the continuous flow stirred tank reactor with advantages from both processes, and we would like
to develop the process to significantly reduce the return of sludge in the clarifier and to secure the reliable quality of treated water by
adding the moving media. Corresponding process has the appropriate
form as an infrastructure based on u- environment in future u- City and
is expected to accelerate the implementation of u-Eco city in conjunction with city based services. The system being conducted in a
laboratory scale has been operated in HRT 8hours except for the final
clarifier and showed the removal efficiency of 97.7 %, 73.1 % and 9.4
% in organic matters, TN and TP, respectively with operating range of
4hour cycle on system SRT 10days. After adding the media, the removal efficiency of phosphorus showed a similar level compared to
that before the addition, but the removal efficiency of nitrogen was
improved by 7~10 %. In addition, the solids which were maintained in
MLSS 1200~1400 at 25 % of media packing were attached all onto the
media, which produced no sludge entering the clarifier. Therefore, the
return of sludge is not needed any longer.
Abstract: Analysis of reciprocating equipment piston rod leads
to nonlinear elastic-plastic deformation analysis of rod with initial
imperfection under axial dynamic load. In this paper a new and
effective model and analytical formulations are presented to evaluate
dynamic deformation and elastic-plastic stresses of reciprocating
machine piston rod. This new method has capability to account for
geometric nonlinearity, elastic-plastic deformation and dynamic
effects. Proposed method can be used for evaluation of piston rod
performance for various reciprocating machines under different
operation situations. Rod load curves and maximum allowable rod
load are calculated with presented method for a refinery type
reciprocating compressor. Useful recommendations and guidelines
for rod load, rod load reversal and rod drop monitoring are also
addressed.
Abstract: This paper deals with rheological behavior of tomato
paste from the view point of time independent properties inclusive of
processing variables such as sample temperature which influence on
rheological properties as well as breaking temperature and
concentration which beside the rheological properties, influence on
the quality of final product. With this aim 10 tomato paste samples at
various concentrations (17-25%) and breaking temperatures (65-
85 C o ) have been produced. The experimental results showed tomato
paste behaves as a non-Newtonian semi-fluid which follows power
law model that consistency coefficient (K) is supposed function of
breaking temperature, concentration and sample temperature with
consideration to superimpose function.
Abstract: Participation in global trade means that Chinas vegetables and fruits industry faces international food safety standards and increased scrutiny worldwide. The objectives of this paper were to investigate how existing food safety standards and regulations in the importing countries impact the export of vegetables and fruits from China. This paper discussed the current and historical situations of Chinas vegetables and fruits export from 1996 to 2010, analyzed the Maximum Residual Limit (MRL) standards of pesticides imposed by importing countries, quantitatively estimated the impacts of food safety standards on Chinas vegetables and fruits export based on a gravity model. The results showed that although transportation distance between trade partners and tariff rates on vegetables and fruits were still the importantly resistant factors for China export, vegetables and fruits export was sensitive to the number of regulated pesticides, the strictness, and the level of food safety standards imposed by importing countries, which showed a significant trade flow effect, stricter food safety standards, increased number of regulated pesticides significantly inhibit China export of vegetables and fruits. Moreover, Chinas food safety standards also showed a significantly effect on vegetables and fruits export, which inhibited export to some extent. KeywordsFood safety standards, MRL, Vegetables, Fruits, Export.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: In this paper, the Lennard -Jones potential is applied
to molecules of liquid argon as well as its vapor and platinum as solid
surface in order to perform a non-equilibrium molecular dynamics
simulation to study the microscopic aspects of liquid-vapor-solid
interactions. The channel is periodic in x and y directions and along z
direction it is bounded by atomic walls. It was found that density of
the liquids near the solid walls fluctuated greatly and that the
structure was more like a solid than a liquid. This indicates that the
interactions of solid and liquid molecules are very strong. The
resultant surface tension, liquid density and vapor density are found
to be well predicted when compared with the experimental data for
argon. Liquid and vapor densities were found to depend on the cutoff
radius which induces the use of P3M (particle-particle particle-mesh)
method which was implemented for evaluation of force and surface
tension.
Abstract: Research into the problem of classification of sonar signals has been taken up as a challenging task for the neural networks. This paper investigates the design of an optimal classifier using a Multi layer Perceptron Neural Network (MLP NN) and Support Vector Machines (SVM). Results obtained using sonar data sets suggest that SVM classifier perform well in comparison with well-known MLP NN classifier. An average classification accuracy of 91.974% is achieved with SVM classifier and 90.3609% with MLP NN classifier, on the test instances. The area under the Receiver Operating Characteristics (ROC) curve for the proposed SVM classifier on test data set is found as 0.981183, which is very close to unity and this clearly confirms the excellent quality of the proposed classifier. The SVM classifier employed in this paper is implemented using kernel Adatron algorithm is seen to be robust and relatively insensitive to the parameter initialization in comparison to MLP NN.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: Using steelmaking slag as a raw material, aragonite superstructure product had been synthesized via an indirect CO2 mineral sequestration rout. It mainly involved two separate steps, in which the element of calcium is first selectively leached from steelmaking slag by a novel leaching media consisting of organic solvent Tributyl phosphate (TBP), acetic acid, and ultra-purity water, followed by enhanced carbonation in a separate step for aragonite superstructure production as well as efficiency recovery of leaching media. Based on the different leaching medium employed in the steelmaking slag leaching process, two typical products were collected from the enhanced carbonation step. The products were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM), respectively. It reveals that the needle-like aragonite crystals self-organized into aragonite superstructure particles including aragonite microspheres as well as dumbbell-like spherical particles, can be obtained from the steelmaking slag with the purity over 99%.
Abstract: This paper presents a novel approach to finding a
priori interesting regions in mammograms. In order to delineate those
regions of interest (ROI-s) in mammograms, which appear to be
prominent, a topographic representation called the iso-level contour
map consisting of iso-level contours at multiple intensity levels and
region segmentation based-thresholding have been proposed. The
simulation results indicate that the computed boundary gives the
detection rate of 99.5% accuracy.
Abstract: Networked schools have become a feature of
education systems in countries that seek to provide learning
opportunities in schools located beyond major centres of population.
The internet and e-learning have facilitated the development of
virtual educational structures that complement traditional schools,
encouraging collaborative teaching and learning to proceed. In rural
New Zealand and in the Atlantic Canadian province of
Newfoundland and Labrador, e-learning is able to provide new ways
of organizing teaching, learning and the management of educational
opportunities. However, the future of e-teaching and e-learning in
networked schools depends on the development of professional
education programs that prepare teachers for collaborative teaching
and learning environments in which both virtual and traditional face
to face instruction co-exist.
Abstract: A common way to elude the signature-based Network Intrusion Detection System is based upon changing a recognizable attack to an unrecognizable one via the IDS. For example, in order to evade sign accommodation with intrusion detection system markers, a hacker spilt the payload packet into many small pieces or hides them within messages. In this paper we try to model the main fragmentation attack and create a new module in the intrusion detection architecture system which recognizes the main fragmentation attacks through verification of integrity checking of TCP packet in order to prevent elusion of the system and also to announce the necessary alert to the system administrator.
Abstract: Forty-five dairy cows were used to compare the
enzyme activity of alkaline phosphatase (ALP), lactate
dehydrogenase (LDH), α -amylase in the cervical mucus of cows
during spontaneous and induced estrus using progestagen or PGF2 α
and to determine whether these enzymes affect the fertility in cows
with induced estrus, at the time of Al. The animals were assigned to 3
groups (no treatment, a Crestar® for 12 days, a double im injection of
PGF2 α). The cows were artificially inseminated (AI). Cervical
mucus samples were collected from all cows 3 to 5 min before the
AI. The results are summarized as follows: ALP and α -amylase
activity for spontaneous estrus were similar to those for induced
estrus (P>0.05) . LDH activity levels during spontaneous and PGF2 α
induced estrus was significantly lower (P < 0.001) than that in
progestagene induced estrus groups. While no difference was found
between the first and the third groups. Our result showed a significant
difference in LDH activity levels between cows conceived with 2 or
more AI and those conceived with 1 AI. The result of this study
showed that the enzyme activity in cervical mucus is helpful for
detection of ovulation and time of AI.
Abstract: The experimental study of position control of a light
weight and small size robotic finger during non-contact motion is
presented in this paper. The finger possesses fingertip pinching and
self adaptive grasping capabilities, and is made of a seven bar linkage
mechanism with a slider in the middle phalanx. The control system is
tested under the Proportional Integral Derivative (PID) control
algorithm and Recursive Least Square (RLS) based Feedback Error
Learning (FEL) control scheme to overcome the uncertainties present
in the plant. The experiments conducted in Matlab Simulink and xPC
Target environments show that the overall control strategy is efficient
in controlling the finger movement.
Abstract: This research work takes a different approach in
the discussion of urban form impacts on transport planning and
auto dependency. Concentrated density represented by effective
density explains auto dependency better than the conventional
density and it is proved to be a realistic density representative for
the urban transportation analysis. Model analysis reveals that
effective density is influenced by the shopping accessibility
index as well as job density factor. It is also combined with the
job access variable to classify four levels of Transport Activity
Centers (TACs) in Okinawa, Japan. Trip attraction capacity and
levels of the newly classified TACs was found agreeable with the
amount of daily trips attracted to each center. The trip attraction
data set was drawn from a 2007 Okinawa personal trip survey.
This research suggests a planning methodology which guides
logical transport supply routes and concentrated local
development schemes.
Abstract: This paper investigates the performance of a speech
recognizer in an interactive voice response system for various coded
speech signals, coded by using a vector quantization technique namely
Multi Switched Split Vector Quantization Technique. The process of
recognizing the coded output can be used in Voice banking application.
The recognition technique used for the recognition of the coded speech
signals is the Hidden Markov Model technique. The spectral distortion
performance, computational complexity, and memory requirements of
Multi Switched Split Vector Quantization Technique and the
performance of the speech recognizer at various bit rates have been
computed. From results it is found that the speech recognizer is
showing better performance at 24 bits/frame and it is found that the
percentage of recognition is being varied from 100% to 93.33% for
various bit rates.