Abstract: Micro power sources are required to be used in autonomous microelectromechanical system (MEMS). In this paper,
we designed and fabricated a three dimensional (3D) MEMS supercapacitor, which is consisting of conformal silicon
dioxide/titanium/polypyrrole (PPy) layers on silicon substrate. At first, ''through-structure'' was fabricated on the silicon substrate by high-aspect-ratio deep reactive ion etching (DRIE) method, which enlarges the available surface area significantly. Then the SiO2/Ti/PPy layers grew sequentially on the ³through-structure´. Finally, the supercapacitor was investigated by electrochemical methods.
Abstract: In this paper, a thermal model of cast- resin dry type
transformer is proposed. The proposed thermal model is solved by
finite element technique to get the temperature at any location of the
transformer. The basic modes of heat transfer such as conduction;
convection and radiation are used to get the steady state temperature
distribution of the transformer. The predicted temperatures are
compared with experimental results reported in this paper and it is
found a good agreement between them. The effects of various
parameters such as width of air duct, ambient temperature and
emissivity of the outer surface were also studied.
Abstract: Since atmosphere pressure field is an actual envoy of
climatic signal the atmospheric Highs and Lows should be attributed
to the key active focal points within the ocean-atmosphere interplay
system. Here we were set a task to determine how the dynamics of
those centres of action relates to the climate change both on regional
and global scales. For this target the near-surface temperature and
atmospheric pressure differences between the Icelandic Low and the
Azores High were considered. The secular term of phase states of the
system under consideration was found divided into three
nonintersecting subsets. Each of that was put in consequence with
one of three climatic scenarios related to the periods of 1905-1935
(relatively warm phase), 1940-1970 (cold phase) and 1980-2000
(warm phase).
Abstract: Spray chilling using air-mist nozzles has received
much attention in the food processing industry because of the
benefits it has shown over forced air convection. These benefits
include an increase in the heat transfer coefficient and a reduction in
the water loss by the product during cooling. However, few studies
have simulated the heat transfer and aerodynamics phenomena of the
air-mist chilling process for optimal operating conditions. The study
provides insight into the optimal conditions for spray impaction, heat
transfer efficiency and control of surface flooding. A computational
fluid dynamics model using a two-phase flow composed of water
droplets injected with air is developed to simulate the air-mist
chilling of food products. The model takes into consideration
droplet-to-surface interaction, water-film accumulation and surface
runoff. The results of this study lead to a better understanding of the
heat transfer enhancement, water conservation, and to a clear
direction for the optimal design of air-mist chilling systems that can
be used in commercial applications in the food and meat processing
industries.
Abstract: Four phenylurea herbicides (isoproturon, chlortoluron, diuron and linuron) were dissolved in different water matrices in order to study their chemical degradation by using UV radiation, ozone and some advanced oxidation processes (UV/H2O2, O3/H2O2, Fenton reagent and the photo- Fenton system). The waters used were: ultra-pure water, a commercial mineral water, a groundwater and a surface water taken from a reservoir. Elimination levels were established for each herbicide and for several global quality parameters, and a kinetic study was performed in order to determine basic kinetic parameters of each reaction between the target phenylureas and these oxidizing systems.
Abstract: Lattice Monte Carlo methods are an excellent
choice for the simulation of non-linear thermal diffusion
problems. In this paper, and for the first time, Lattice Monte
Carlo analysis is performed on thermal diffusion combined
with convective heat transfer. Laminar flow of water modeled
as an incompressible fluid inside a copper pipe with a constant
surface temperature is considered. For the simulation of
thermal conduction, the temperature dependence of the
thermal conductivity of the water is accounted for. Using the
novel Lattice Monte Carlo approach, temperature distributions
and energy fluxes are obtained.
Abstract: In this paper, four carbazole-based D-D-π-A organic
dyes code as CCT2A, CCT3A, CCT1PA and CCT2PA were reported.
A series of these organic dyes containing identical donor and
acceptor group but different π-system. The effect of replacing of
thiophene by phenyl thiophene as π-system on the physical
properties has been focused. The structural, energetic properties and
absorption spectra were theoretically investigated by means of
Density Functional Theory (DFT) and Time-Dependent Density
Functional Theory (TD-DFT). The results show that nonplanar
conformation due to steric hindrance in donor part (cabazolecarbazole
unit) of dye molecule can prevent unfavorable dye
aggregation. By means of the TD-DFT method, the absorption
spectra were calculated by B3LYP and BHandHLYP to study the
affect of hybrid functional on the excitation energy (Eg). The results
revealed the increasing of thiophene units not only resulted in
decreasing of Eg, but also found the shifting of absorption spectra to
higher wavelength. TD-DFT/BHandHLYP calculated results are
more strongly agreed with the experimental data than B3LYP
functions. Furthermore, the adsorptions of CCT2A and CCT3A on the
TiO2 anatase (101) surface were carried out by mean of the chemical
periodic calculation. The result exhibit the strong adsorption energy.
The calculated results provide our new organic dyes can be
effectively used as dye for Dye Sensitized Solar Cell (DSC).
Abstract: Soy polyol obtained from hydroxylation of soy
epoxide with ethylene glycol were prepared as pre-polyurethane. The
two step process method were applied in the polyurethane synthesis.
The blending of soy polyol with synthetic polyol then simultaneously
carried out to TDI (2,4): MDI (4,4-) (80:20), blowing agent, and
surfactant. Ethylene glycol were not taking part in the polyurethane
synthesis. The inclusion of ethylene glycol were used as a control.
Characterization of polyurethane foam through impact resillience,
indentation deflection, and density can visualize the polyurethane
classifications.
Abstract: Among many different methods that are used for
optimizing different engineering problems mathematical (numerical)
optimization techniques are very important because they can easily
be used and are consistent with most of engineering problems. Many
studies and researches are done on stability analysis of three
dimensional (3D) slopes and the relating probable slip surfaces and
determination of factors of safety, but in most of them force
equilibrium equations, as in simplified 2D methods, are considered
only in two directions. In other words for decreasing mathematical
calculations and also for simplifying purposes the force equilibrium
equation in 3rd direction is omitted. This point is considered in just a
few numbers of previous studies and most of them have only given a
factor of safety and they haven-t made enough effort to find the most
probable slip surface. In this study shapes of the slip surfaces are
modeled, and safety factors are calculated considering the force
equilibrium equations in all three directions, and also the moment
equilibrium equation is satisfied in the slip direction, and using
nonlinear programming techniques the shape of the most probable
slip surface is determined. The model which is used in this study is a
3D model that is composed of three upper surfaces which can cover
all defined and probable slip surfaces. In this research the meshing
process is done in a way that all elements are prismatic with
quadrilateral cross sections, and the safety factor is defined on this
quadrilateral surface in the base of the element which is a part of the
whole slip surface. The method that is used in this study to find the
most probable slip surface is the non-linear programming method in
which the objective function that must get optimized is the factor of
safety that is a function of the soil properties and the coordinates of
the nodes on the probable slip surface. The main reason for using
non-linear programming method in this research is its quick
convergence to the desired responses. The final results show a good
compatibility with the previously used classical and 2D methods and
also show a reasonable convergence speed.
Abstract: This paper suggests a calibration method to reduce
errors occurring due to mobile robot sliding during location estimation
using the Dead-reckoning. Due to sliding of the mobile robot caused
between its wheels and the road surface while on free run, location
estimation can be erroneous. Sliding especially occurs during
cornering of mobile robot. Therefore, in order to reduce these frequent
sliding errors in cornering, we calibrated the mobile robot-s heading
values using a vision camera and templates of the ceiling.
Abstract: In this research, natural canthaxanthin as one of the
most important carotenoids was extracted from Dietzia
natronolimnaea HS-1. The changes of canthaxanthin enriched in oilin-
water emulsions with vegetable oil (5 mg/ 100 mL), Arabic gum (5
mg/100 mL), and potassium sorbate (0.5 g/100 mL) was investigated.
The effects of different pH (3, 5 and 7), as well as, time treatment (3,
18 and 33 days) in the environmental temperature (24°C) on the
degradation were studied by response surface methodology (RSM).
The Hunter values (L*, a*, and b*) and the concentration of
canthaxanthin (C, mg/L) illustrated more degradation of this pigment
at low pHs (pH≤ 4) by passing the time (days≥10) with R² 97.00%,
91.31%, 97.60%, and 99.54% for C, L*, a*, and b* respectively. The
predicted model were found to be significant (p
Abstract: In this paper, algorithms for the automatic localisation
of two anatomical soft tissue landmarks of the head the medial
canthus (inner corner of the eye) and the tragus (a small, pointed,
cartilaginous flap of the ear), in CT images are describet. These
landmarks are to be used as a basis for an automated image-to-patient
registration system we are developing. The landmarks are localised
on a surface model extracted from CT images, based on surface
curvature and a rule based system that incorporates prior knowledge
of the landmark characteristics. The approach was tested on a dataset
of near isotropic CT images of 95 patients. The position of the
automatically localised landmarks was compared to the position of
the manually localised landmarks. The average difference was 1.5
mm and 0.8 mm for the medial canthus and tragus, with a maximum
difference of 4.5 mm and 2.6 mm respectively.The medial canthus
and tragus can be automatically localised in CT images, with
performance comparable to manual localisation
Abstract: The present paper is an experimental investigation of
roughness effects on nucleate pool boiling of refrigerant R113 on
horizontal circular copper surfaces. The copper samples were treated
by different sand paper grit sizes to achieve different surface
roughness. The average surface roughness of the four samples was
0.901, 0.735, 0.65, and 0.09, respectively. The experiments were
performed in the heat flux range of 8 to 200kW/m2. The heat transfer
coefficient was calculated by measuring wall superheat of the
samples and the input heat flux. The results show significant
improvement of heat transfer coefficient as the surface roughness is
increased. It is found that the heat transfer coefficient of the sample
with Ra=0.901 is 3.4, 10.5, and 38.5% higher in comparison with
surfaces with Ra of 0.735, 0.65, and 0.09 at heat flux of 170 kW/m2.
Moreover, the results are compared with literature data and the well
known Cooper correlation.
Abstract: In vitro gastro-duodenal digestion model was used to investigate the changes of emulsions under digestion conditions. Oil in water emulsions stabilized by whey proteins (2%) and stabilized by whey proteins (2%) with addition of carboxymethyl cellulose (0.75%) as gelling agent of continuous phase were prepared at pH7. Both emulsions were destabilized under gastric conditions; however the protective role of carboxymethyl cellulose was indicated by recording delay of fat digestibility of this emulsion. In the presence of carboxymethyl cellulose whey proteins on the interfacial surface of droplets were more resistant to gastric degradation causing limited hydrolysis of fat due to the poor acceptability of lipids for the enzymes. Studies of emulsions using in vivo model supported results from in vitro studies. Lower content of triglycerides in blood serum and higher amount of fecal fat of rats were determined when rats were fed by diet containing emulsion made with whey proteins and carboxymethyl cellulose.
Abstract: Aspheric optical components are an alternative to the use of conventional lenses in the implementation of imaging systems for the visible range. Spherical lenses are capable of producing aberrations. Therefore, they are not able to focus all the light into a single point. Instead, aspherical lenses correct aberrations and provide better resolution even with compact lenses incorporating a small number of lenses.
Metrology of these components is very difficult especially when the resolution requirements increase and insufficient or complexity of conventional tools requires the development of specific approaches to characterization.
This work is part of the problem existed because the objectives are the study and comparison of different methods used to measure surface rays hybrid aspherical lenses.
Abstract: In this paper, fabrication and study of electronic properties of Au/methyl-red/Ag surface type Schottky diode by current-voltage (I-V) method has been reported. The I-V characteristics of the Schottky diode showed the good rectifying behavior. The values of ideality factor n and barrier height b of Au/methyl-red/Ag Schottky diode were calculated from the semi-log I-V characteristics and by using the Cheung functions. From semi-log current-voltage characteristics the values of n and b were found 1.93 and 0.254 eV, respectively, while by using Cheung functions their values were calculated 1.89 and 0.26 eV, respectively. The effect of series resistance was also analyzed by Cheung functions. The series resistance RS values were determined from dV/d(lnI)–I and H(I)–I graphs and were found to be 1.1 k and 1.3 k, respectively.
Abstract: Studies have shown that the SnAgCu solder family has been widely used as a replacement for conventional Sn-Pb solders. An attractive approach is by introducing alloying additives (rare earth elements (RE), Zn, Co, Fe, Ni, Sb) into the SnAgCu solder, which helps in refining the microstructure also improving the mechanical and wetting properties of the solder. The present work focuses on the effect of additions of 0.5% Ce and Fe into Sn-3.0Ag-0.5Cu solder, in attempt to reduce the intermetallic compound (IMC) growth and reflow properties of the solder on Cu and Ni (P) surface finish, as well as effects thermal aging on the formation of intermetallic compound (IMC) on different surface finish. Excessive intermetallic compound growth may effect the interface and solder joint due to the brittle nature of the intermetallic compounds. Thus, by introducing alloying elements, IMC layer thickness can be decrease, resulting in better joint and solder reliability.
Abstract: The paper shows some ability to manage two-phase
flows arising from the use of unsteady effects. In one case, we
consider the condition of fragmentation of the interface between the
two components leads to the intensification of mixing. The problem
is solved when the temporal and linear scale are small for the
appearance of the developed mixing layer. Showing that exist such
conditions for unsteady flow velocity at the surface of the channel,
which will lead to the creation and fragmentation of vortices at Re
numbers of order unity. Also showing that the Re is not a criterion of
similarity for this type of flows, but we can introduce a criterion that
depends on both the Re, and the frequency splitting of the vortices. It
turned out that feature of this situation is that streamlines behave
stable, and if we analyze the behavior of the interface between the
components it satisfies all the properties of unstable flows. The other
problem we consider the behavior of solid impurities in the extensive
system of channels. Simulated unsteady periodic flow modeled
breaths. Consider the behavior of the particles along the trajectories.
It is shown that, depending on the mass and diameter of the particles,
they can be collected in a caustic on the channel walls, stop in a
certain place or fly back. Of interest is the distribution of particle
velocity in frequency. It turned out that by choosing a behavior of the
velocity field of the carrier gas can affect the trajectory of individual
particles including force them to fly back.
Abstract: We attempted investigate a boat model, based on the
conversion of energy of surface wave into a sequence of
unidirectional pulses of jet spurts, in other words - model of the boat,
which is thrusting by the waves field on water surface. These pulses
are forming some average reactive stream from the output nozzle on
the stern of boat. The suggested model provides the conversion of its
oscillatory motions (both pitching and rolling) into a jet flow. This
becomes possible due to special construction of the boat and due to
several details, sensitive to the local wave field. The boat model
presents the uniflow jet engine without slow conversions of
mechanical energy into intermediate forms and without any external
sources of energy (besides surface waves). Motion of boat is
characterized by fast jerks and average onward velocity, which
exceeds the velocities of liquid particles in the wave.
Abstract: In this paper, a generalized self-consistent scheme, or “three phase model", is used to set up a micro-mechanics model for rough surface contact with randomly distributed asperities. The dimensionless average real pressure p is obtained as function of the ratio of the real contact area to the apparent contact area, 0 A / A r . Both elastic and plastic materials are considered, and the influence of the plasticity of material on p is discussed. Both two-dimensional and three-dimensional rough surface contact problems are considered.