Abstract: In this study, stress distributions on dental implants
made of functionally graded biomaterials (FGBM) are investigated
numerically. The implant body is considered to be subjected to axial
compression loads. Numerical problem is assumed to be 2D, and
ANSYS commercial software is used for the analysis. The cross
section of the implant thread varies as varying the height (H) and the
width (t) of the thread. According to thread dimensions of implant
and material properties of FGBM, equivalent stress distribution on
the implant is determined and presented with contour plots along
with the maximum equivalent stress values. As a result, with
increasing material gradient parameter (n), the equivalent stress
decreases, but the minimum stress distribution increases. Maximum
stress values decrease with decreasing implant radius (r). Maximum
von Mises stresses increases with decreasing H when t is constant.
On the other hand, the stress values are not affected by variation of t
in the case of H = constant.
Abstract: The design of weight is one of the important parts in
fuzzy decision making, as it would have a deep effect on the evaluation
results. Entropy is one of the weight measure based on objective
evaluation. Non--probabilistic-type entropy measures for fuzzy set
and interval type-2 fuzzy sets (IT2FS) have been developed and applied
to weight measure. Since the entropy for (IT2FS) for decision
making yet to be explored, this paper proposes a new objective
weight method by using entropy weight method for multiple attribute
decision making (MADM). This paper utilizes the nature of IT2FS
concept in the evaluation process to assess the attribute weight based
on the credibility of data. An example was presented to demonstrate
the feasibility of the new method in decision making. The entropy
measure of interval type-2 fuzzy sets yield flexible judgment and
could be applied in decision making environment.
Abstract: In the present work homogeneous silica film on
silicon was fabricated by colloidal silica sol. The silica sol precursor
with uniformly granular particle was derived by the alkaline
hydrolysis of tetraethoxyorthosilicate (TEOS) in presence of glycerol
template. The film was prepared by dip coating process. The
templated hetero-structured silica film was annealed at elevated
temperatures to generate nano- and meso porosity in the film. The
film was subsequently annealed at different temperatures to make it
defect free and abrasion resistant. The sol and the film were
characterized by the measurement of particle size distribution,
scanning electron microscopy, XRD, FTIR spectroscopy,
transmission electron microscopy, atomic force microscopy,
measurement of the refractive index, thermal conductivity and
abrasion resistance. The porosity of the films decreased whereas
refractive index and dielectric constant of it `increased with the
increase in the annealing temperature. The thermal conductivity of
the films increased with the increase in the film thickness. The
developed porous silica film holds strong potential for use in
different areas.
Abstract: Combustion of sprays is of technological importance, but its flame behavior is not fully understood. Furthermore, the multiplicity of dependent variables such as pressure, temperature, equivalence ratio, and droplet sizes complicates the study of spray combustion. Fundamental study on the influence of the presence of liquid droplets has revealed that laminar flames within aerosol mixtures more readily become unstable than for gaseous ones and this increases the practical burning rate. However, fundamental studies on turbulent flames of aerosol mixtures are limited particularly those under near mono-dispersed droplet conditions. In the present work, centrally ignited expanding flames at near atmospheric pressures are employed to quantify the burning rates in gaseous and aerosol flames. Iso-octane-air aerosols are generated by expansion of the gaseous pre-mixture to produce a homogeneously distributed suspension of fuel droplets. The effects of the presence of droplets and turbulence velocity in relation to the burning rates of the flame are also investigated.
Abstract: This article proposes a voltage-mode
multifunction filter using differential voltage current
controllable current conveyor transconductance amplifier
(DV-CCCCTA). The features of the circuit are that: the
quality factor and pole frequency can be tuned independently
via the values of capacitors: the circuit description is very
simple, consisting of merely 1 DV-CCCCTA, and 2
capacitors. Without any component matching conditions, the
proposed circuit is very appropriate to further develop into
an integrated circuit. Additionally, each function response
can be selected by suitably selecting input signals with
digital method. The PSpice simulation results are depicted.
The given results agree well with the theoretical anticipation.
Abstract: In this article, we aim to discuss the formulation of two explicit group iterative finite difference methods for time-dependent two dimensional Burger-s problem on a variable mesh. For the non-linear problems, the discretization leads to a non-linear system whose Jacobian is a tridiagonal matrix. We discuss the Newton-s explicit group iterative methods for a general Burger-s equation. The proposed explicit group methods are derived from the standard point and rotated point Crank-Nicolson finite difference schemes. Their computational complexity analysis is discussed. Numerical results are given to justify the feasibility of these two proposed iterative methods.
Abstract: The dynamic spectrum allocation solutions such as
cognitive radio networks have been proposed as a key technology to
exploit the frequency segments that are spectrally underutilized.
Cognitive radio users work as secondary users who need to
constantly and rapidly sense the presence of primary users or
licensees to utilize their frequency bands if they are inactive. Short
sensing cycles should be run by the secondary users to achieve
higher throughput rates as well as to provide low level of interference
to the primary users by immediately vacating their channels once
they have been detected. In this paper, the throughput-sensing time
relationship in local and cooperative spectrum sensing has been
investigated under two distinct scenarios, namely, constant primary
user protection (CPUP) and constant secondary user spectrum
usability (CSUSU) scenarios. The simulation results show that the
design of sensing slot duration is very critical and depends on the
number of cooperating users under CPUP scenario whereas under
CSUSU, cooperating more users has no effect if the sensing time
used exceeds 5% of the total frame duration.
Abstract: Xanthan gum is one of the major commercial
biopolymers. Due to its excellent rheological properties xanthan gum
is used in many applications, mainly in food industry. Commercial
production of xanthan gum uses glucose as the carbon substrate;
consequently the price of xanthan production is high. One of the
ways to decrease xanthan price, is using cheaper substrate like
agricultural wastes. Iran is one of the biggest date producer countries.
However approximately 50% of date production is wasted annually.
The goal of this study is to produce xanthan gum from waste date
using Xanthomonas campestris PTCC1473 by submerged
fermentation. In this study the effect of three variables including
phosphor and nitrogen amount and agitation rate in three levels using
response surface methodology (RSM) has been studied. Results
achieved from statistical analysis Design Expert 7.0.0 software
showed that xanthan increased with increasing level of phosphor.
Low level of nitrogen leaded to higher xanthan production. Xanthan
amount, increasing agitation had positive influence. The statistical
model identified the optimum conditions nitrogen amount=3.15g/l,
phosphor amount=5.03 g/l and agitation=394.8 rpm for xanthan. To
model validation, experiments in optimum conditions for xanthan
gum were carried out. The mean of result for xanthan was 6.72±0.26.
The result was closed to the predicted value by using RSM.
Abstract: Structural Integrity Management (SIM) is
important for the protection of offshore crew, environment, business assets and company and industry reputation. API RP 2A contained guidelines for assessment of existing platforms mostly for the Gulf
of Mexico (GOM). ISO 19902 SIM framework also does not
specifically cater for Malaysia. There are about 200 platforms in
Malaysia with 90 exceeding their design life. The Petronas Carigali
Sdn Bhd (PCSB) uses the Asset Integrity Management System and
the very subjective Risk based Inspection Program for these
platforms. Petronas currently doesn-t have a standalone Petronas
Technical Standard PTS-SIM. This study proposes a recommended
practice for the SIM process for offshore structures in Malaysia,
including studies by API and ISO and local elements such as the
number of platforms, types of facilities, age and risk ranking. Case
study on SMG-A platform in Sabah shows missing or scattered
platform data and a gap in inspection history. It is to undergo a level
3 underwater inspection in year 2015.
Abstract: Using activity theory, organisational theory and
didactics as theoretical foundations, a comprehensive model of the
organisational dimensions relevant for learning and knowledge
transfer will be developed. In a second step, a Learning Assessment
Guideline will be elaborated. This guideline will be designed to
permit a targeted analysis of organisations to identify the status quo
in those areas crucial to the implementation of learning and
knowledge transfer. In addition, this self-analysis tool will enable
learning managers to select adequate didactic models for e- and
blended learning. As part of the European Integrated Project
"Process-oriented Learning and Information Exchange" (PROLIX),
this model of organisational prerequisites for learning and knowledge
transfer will be empirically tested in four profit and non-profit
organisations in Great Britain, Germany and France (to be finalized
in autumn 2006). The findings concern not only the capability of the
model of organisational dimensions, but also the predominant
perceptions of and obstacles to learning in organisations.
Abstract: Leptospirosis is recognized as an important zoonosis
in tropical regions well as an important animal disease with
substantial loss in production. In this study, the model for the
transmission of the Leptospirosis disease to human population are
discussed. Model is described the vector population dynamics and
the Leptospirosis transmission to the human population are
discussed. Local analysis of equilibria are given. We confirm the
results by using numerical results.
Abstract: Large volumes of fingerprints are collected and stored
every day in a wide range of applications, including forensics, access
control etc. It is evident from the database of Federal Bureau of
Investigation (FBI) which contains more than 70 million finger
prints. Compression of this database is very important because of this
high Volume. The performance of existing image coding standards
generally degrades at low bit-rates because of the underlying block
based Discrete Cosine Transform (DCT) scheme. Over the past
decade, the success of wavelets in solving many different problems
has contributed to its unprecedented popularity. Due to
implementation constraints scalar wavelets do not posses all the
properties which are needed for better performance in compression.
New class of wavelets called 'Multiwavelets' which posses more
than one scaling filters overcomes this problem. The objective of this
paper is to develop an efficient compression scheme and to obtain
better quality and higher compression ratio through multiwavelet
transform and embedded coding of multiwavelet coefficients through
Set Partitioning In Hierarchical Trees algorithm (SPIHT) algorithm.
A comparison of the best known multiwavelets is made to the best
known scalar wavelets. Both quantitative and qualitative measures of
performance are examined for Fingerprints.
Abstract: Identity verification of authentic persons by their multiview faces is a real valued problem in machine vision. Multiview faces are having difficulties due to non-linear representation in the feature space. This paper illustrates the usability of the generalization of LDA in the form of canonical covariate for face recognition to multiview faces. In the proposed work, the Gabor filter bank is used to extract facial features that characterized by spatial frequency, spatial locality and orientation. Gabor face representation captures substantial amount of variations of the face instances that often occurs due to illumination, pose and facial expression changes. Convolution of Gabor filter bank to face images of rotated profile views produce Gabor faces with high dimensional features vectors. Canonical covariate is then used to Gabor faces to reduce the high dimensional feature spaces into low dimensional subspaces. Finally, support vector machines are trained with canonical sub-spaces that contain reduced set of features and perform recognition task. The proposed system is evaluated with UMIST face database. The experiment results demonstrate the efficiency and robustness of the proposed system with high recognition rates.
Abstract: This paper provides a key driver-based conceptual framework that can be used to improve a firm-s success in commercializing technology and in new product innovation resulting from collaboration with other organizations through strategic alliances. Based on a qualitative study using an interview approach, strategic alliances of entrepreneurs in the food processing industry in Thailand are explored. This paper describes factors affecting decisions to collaborate through alliances. It identifies four issues: maintaining the efficiency of the value chain for production capability, adapting to present and future competition, careful assessment of value of outcomes, and management of innovation. We consider five driving factors: resource orientation, assessment of risk, business opportunity, sharing of benefits and confidence in alliance partners. These factors will be of interest to entrepreneurs and policy makers with regard to further understanding of the direction of business strategies.
Abstract: In this research, heat transfer of a poly Ethylene
fluidized bed reactor without reaction were studied experimentally
and computationally at different superficial gas velocities. A multifluid
Eulerian computational model incorporating the kinetic theory
for solid particles was developed and used to simulate the heat
conducting gas–solid flows in a fluidized bed configuration.
Momentum exchange coefficients were evaluated using the Syamlal–
O-Brien drag functions. Temperature distributions of different phases
in the reactor were also computed. Good agreement was found
between the model predictions and the experimentally obtained data
for the bed expansion ratio as well as the qualitative gas–solid flow
patterns. The simulation and experimental results showed that the gas
temperature decreases as it moves upward in the reactor, while the
solid particle temperature increases. Pressure drop and temperature
distribution predicted by the simulations were in good agreement
with the experimental measurements at superficial gas velocities
higher than the minimum fluidization velocity. Also, the predicted
time-average local voidage profiles were in reasonable agreement
with the experimental results. The study showed that the
computational model was capable of predicting the heat transfer and
the hydrodynamic behavior of gas-solid fluidized bed flows with
reasonable accuracy.
Abstract: When acid is pumped into damaged reservoirs for
damage removal/stimulation, distorted inflow of acid into the
formation occurs caused by acid preferentially traveling into highly
permeable regions over low permeable regions, or (in general) into
the path of least resistance. This can lead to poor zonal coverage and
hence warrants diversion to carry out an effective placement of acid.
Diversion is desirably a reversible technique of temporarily reducing
the permeability of high perm zones, thereby forcing the acid into
lower perm zones.
The uniqueness of each reservoir can pose several challenges to
engineers attempting to devise optimum and effective diversion
strategies. Diversion techniques include mechanical placement and/or
chemical diversion of treatment fluids, further sub-classified into ball
sealers, bridge plugs, packers, particulate diverters, viscous gels,
crosslinked gels, relative permeability modifiers (RPMs), foams,
and/or the use of placement techniques, such as coiled tubing (CT)
and the maximum pressure difference and injection rate (MAPDIR)
methodology.
It is not always realized that the effectiveness of diverters greatly
depends on reservoir properties, such as formation type, temperature,
reservoir permeability, heterogeneity, and physical well
characteristics (e.g., completion type, well deviation, length of
treatment interval, multiple intervals, etc.). This paper reviews the
mechanisms by which each variety of diverter functions and
discusses the effect of various reservoir properties on the efficiency
of diversion techniques. Guidelines are recommended to help
enhance productivity from zones of interest by choosing the best
methods of diversion while pumping an optimized amount of
treatment fluid. The success of an overall acid treatment often
depends on the effectiveness of the diverting agents.
Abstract: The objectif of the present work is to determinate the
potential of the solar parabolic trough collector (PTC) for use in the
design of a solar thermal power plant in Algeria. The study is based
on a mathematical modeling of the PTC. Heat balance has been
established respectively on the heat transfer fluid (HTF), the absorber
tube and the glass envelop using the principle of energy conservation
at each surface of the HCE cross-sectionn. The modified Euler
method is used to solve the obtained differential equations. At first
the results for typical days of two seasons the thermal behavior of the
HTF, the absorber and the envelope are obtained. Then to determine
the thermal performances of the heat transfer fluid, different oils are
considered and their temperature and heat gain evolutions compared.
Abstract: This research paper deals with the implementation of face recognition using neural network (recognition classifier) on low-resolution images. The proposed system contains two parts, preprocessing and face classification. The preprocessing part converts original images into blurry image using average filter and equalizes the histogram of those image (lighting normalization). The bi-cubic interpolation function is applied onto equalized image to get resized image. The resized image is actually low-resolution image providing faster processing for training and testing. The preprocessed image becomes the input to neural network classifier, which uses back-propagation algorithm to recognize the familiar faces. The crux of proposed algorithm is its beauty to use single neural network as classifier, which produces straightforward approach towards face recognition. The single neural network consists of three layers with Log sigmoid, Hyperbolic tangent sigmoid and Linear transfer function respectively. The training function, which is incorporated in our work, is Gradient descent with momentum (adaptive learning rate) back propagation. The proposed algorithm was trained on ORL (Olivetti Research Laboratory) database with 5 training images. The empirical results provide the accuracy of 94.50%, 93.00% and 90.25% for 20, 30 and 40 subjects respectively, with time delay of 0.0934 sec per image.
Abstract: X-ray mammography is the most effective method for
the early detection of breast diseases. However, the typical diagnostic
signs such as microcalcifications and masses are difficult to detect
because mammograms are of low-contrast and noisy. In this paper, a
new algorithm for image denoising and enhancement in Orthogonal
Polynomials Transformation (OPT) is proposed for radiologists to
screen mammograms. In this method, a set of OPT edge coefficients
are scaled to a new set by a scale factor called OPT scale factor. The
new set of coefficients is then inverse transformed resulting in
contrast improved image. Applications of the proposed method to
mammograms with subtle lesions are shown. To validate the
effectiveness of the proposed method, we compare the results to
those obtained by the Histogram Equalization (HE) and the Unsharp
Masking (UM) methods. Our preliminary results strongly suggest
that the proposed method offers considerably improved enhancement
capability over the HE and UM methods.
Abstract: The aim of this study is to show innovative techniques that describe the effectiveness of individuals diagnosed with antisocial personality disorders (ASPD). The author presents information about hate schemas regarding persons with ASPD and their understanding of the role of hate. The data of 60 prisoners with ASPD, 40 prisoners without ASPD, and 60 men without antisocial tendencies, has been analyzed. The participants were asked to describe their hate inspired by a photograph. The narrative discourse was analyzed, the three groups were compared. The results show the differences between the inmates with ASPD, those without ASPD, and the controls. The antisocial individuals describe hate as an ambivalent feeling with low emotional intensity, i.e., actors (in stories) are presented more as positives than as partners. They use different mechanisms to keep them from understanding the meaning of the emotional situation. The schema's characteristics were expressed in narratives attributed to high Psychopathy.