Abstract: The stability characteristics of water lubricated journal bearings having three axial grooves are obtained theoretically. In this lubricant (water) is fed under pressure from one end of the bearing, through the 3-axial grooves (groove angles may vary). These bearings can use the process fluid as the lubricant, as in the case of feed water pumps. The Reynolds equation is solved numerically by the finite difference method satisfying the boundary conditions. The stiffness and damping coefficient for various bearing number and eccentricity ratios, assuming linear pressure drop along the groove, shows that smaller groove angles better results.
Abstract: This paper presents a possibilistic (fuzzy) model in optimal siting and sizing of Distributed Generation (DG) for loss reduction and improve voltage profile in power distribution system. Multi-objective problem is developed in two phases. In the first one, the set of non-dominated planning solutions is obtained (with respect to the objective functions of fuzzy economic cost, and exposure) using genetic algorithm. In the second phase, one solution of the set of non-dominated solutions is selected as optimal solution, using a suitable max-min approach. This method can be determined operation-mode (PV or PQ) of DG. Because of considering load uncertainty in this paper, it can be obtained realistic results. The whole process of this method has been implemented in the MATLAB7 environment with technical and economic consideration for loss reduction and voltage profile improvement. Through numerical example the validity of the proposed method is verified.
Abstract: In this article, a simulation method called the Homotopy Perturbation Method (HPM) is employed in the steady flow of a Walter's B' fluid in a vertical channel with porous wall. We employed Homotopy Perturbation Method to derive solution of a nonlinear form of equation obtained from exerting similarity transforming to the ordinary differential equation gained from continuity and momentum equations of this kind of flow. The results obtained from the Homotopy Perturbation Method are then compared with those from the Runge–Kutta method in order to verify the accuracy of the proposed method. The results show that the Homotopy Perturbation Method can achieve good results in predicting the solution of such problems. Ultimately we use this solution to obtain the other terms of velocities and physical discussion about it.
Abstract: Carriers scattering in the inversion channel of n-
MOSFET dominates the drain current. This paper presents an effective
electron mobility model for the pocket implanted nano scale
n-MOSFET. The model is developed by using two linear pocket
profiles at the source and drain edges. The channel is divided into
three regions at source, drain and central part of the channel region.
The total number of inversion layer charges is found for these three
regions by numerical integration from source to drain ends and the
number of depletion layer charges is found by using the effective
doping concentration including pocket doping effects. These two
charges are then used to find the effective normal electric field,
which is used to find the effective mobility model incorporating the
three scattering mechanisms, such as, Coulomb, phonon and surface
roughness scatterings as well as the ballistic phenomena for the
pocket implanted nano-scale n-MOSFET. The simulation results show
that the derived mobility model produces the same results as found
in the literatures.
Abstract: The flow field within the combustor of scramjet
engine is very complex and poses a considerable challenge in the
design and development of a supersonic combustor with an optimized
geometry. In this paper comprehensive numerical studies on flow
field characteristics of different cavity based scramjet combustors
with transverse injection of hydrogen have been carried out for both
non-reacting and reacting flows. The numerical studies have been
carried out using a validated 2D unsteady, density based 1st-order
implicit k-omega turbulence model with multi-component finite rate
reacting species. The results show a wide variety of flow features
resulting from the interactions between the injector flows, shock
waves, boundary layers, and cavity flows. We conjectured that an
optimized cavity is a good choice to stabilize the flame in the
hypersonic flow, and it generates a recirculation zone in the scramjet
combustor. We comprehended that the cavity based scramjet
combustors having a bearing on the source of disturbance for the
transverse jet oscillation, fuel/air mixing enhancement, and flameholding
improvement. We concluded that cavity shape with
backward facing step and 45o forward ramp is a good choice to get
higher temperatures at the exit compared to other four models of
scramjet combustors considered in this study.
Abstract: A bird strike can cause damage to stationary and
rotating aircraft engine parts, especially the engine fan. This paper
presents a bird strike simulated by blocking four stator blade
passages. It includes the numerical results of the unsteady lowfrequency
aerodynamic forces and the aeroelastic behaviour caused
by a non-symmetric upstream flow affecting the first two rotor blade
stages in the axial-compressor of a jet engine. The obtained results
show that disturbances in the engine inlet strongly influence the level
of unsteady forces acting on the rotor blades. With a partially
blocked inlet the whole spectrum of low-frequency harmonics is
observed. Such harmonics can lead to rotor blade damage. The lowfrequency
amplitudes are higher in the first stage rotor blades than in
the second stage. In both rotor blades stages flutter appeared as a
result of bird strike.
Abstract: This paper studies the pth moment exponential synchronization of a class of stochastic neural networks with mixed delays. Based on Lyapunov stability theory, by establishing a new integrodifferential inequality with mixed delays, several sufficient conditions have been derived to ensure the pth moment exponential stability for the error system. The criteria extend and improve some earlier results. One numerical example is presented to illustrate the validity of the main results.
Abstract: Along with increasing development of generation of supersonic planes especially fighters and request for increasing the performance and maneuverability scientists and engineers suggested the delta and double delta wing design. One of the areas which was necessary to be researched, was the Aerodynamic review of this type of wings in high angles of attack at low speeds that was very important in landing and takeoff the planes and maneuvers. Leading Edges of the wings,cause the separation flow from wing surface and then formation of powerful vortex with high rotational speed which studing the mechanism and location of formation and also the position of the vortex breakdown in high angles of attack is very important. In this research, a double delta wing with 76o/45o sweep angles at high angle of attack in steady state and incompressible flow were numerically analyzed with Fluent software. With analaysis of the numerical results, we arrived the most important characteristic of the double delta wings which is keeping of lift at high angles of attacks.
Abstract: Fuzzy Cognitive Maps (FCMs) is a causal graph, which shows the relations between essential components in complex systems. Experts who are familiar with the system components and their relations can generate a related FCM. There is a big gap when human experts cannot produce FCM or even there is no expert to produce the related FCM. Therefore, a new mechanism must be used to bridge this gap. In this paper, a novel learning method is proposed to construct causal graph based on historical data and by using metaheuristic such Tabu Search (TS). The efficiency of the proposed method is shown via comparison of its results of some numerical examples with those of some other methods.
Abstract: To understand the seismic behavior of the offshore
structures, the dynamic interaction of the water-structure-soil should
be assessed. In this regard the role of the water dynamic properties in
magnifying or reducing of the effects of earthquake induced motions
on offshore structures haven't been investigated in precise manner in
available literature. In this paper the sea water level fluctuations
effects on the seismic behavior of a sample of offshore structures has
been investigated by emphasizing on the water-structure interaction
phenomenon. For this purpose a two dimensional finite element
model of offshore structures as well as surrounded water has been
developed using ANSYS software. The effect of soil interaction with
embedded pile foundation has been imposed by using a series of
nonlinear springs in horizontal and vertical directions in soil-piles
contact points. In the model, the earthquake induced motions have
been applied on springs and consequently the motions propagated
upward to the structure and surrounded water. As a result of
numerical study, the horizontal deformations of the offshore deck as
well as internal force and buckling coefficient in structural elements
have been recorded and controlled with and without water presence.
In part of study a parametric study has been accomplished on sea
water level fluctuations and effect of this parameter has been studied
on the aforementioned numerical results.
Abstract: Numerical analysis of flow characteristics and
separation efficiency in a high-efficiency cyclone has been performed.
Several models based on the experimental observation for a design
purpose were proposed. However, the model is only estimated the
cyclone's performance under the limited environments; it is difficult to
obtain a general model for all types of cyclones. The purpose of this
study is to find out the flow characteristics and separation efficiency
numerically. The Reynolds stress model (RSM) was employed instead
of a standard k-ε or a k-ω model which was suitable for isotropic
turbulence and it could predict the pressure drop and the Rankine
vortex very well. For small particles, there were three significant
components (entrance of vortex finder, cone, and dust collector) for
the particle separation. In the present work, the particle re-entraining
phenomenon from the dust collector to the cyclone body was observed
after considerable time. This re-entrainment degraded the separation
efficiency and was one of the significant factors for the separation
efficiency of the cyclone.
Abstract: This paper presents the robust stability criteria for uncertain genetic regulatory networks with time-varying delays. One key point of the criterion is that the decomposition of the matrix ˜D into ˜D = ˜D1 + ˜D2. This decomposition corresponds to a decomposition of the delayed terms into two groups: the stabilizing ones and the destabilizing ones. This technique enables one to take the stabilizing effect of part of the delayed terms into account. Meanwhile, by choosing an appropriate new Lyapunov functional, a new delay-dependent stability criteria is obtained and formulated in terms of linear matrix inequalities (LMIs). Finally, numerical examples are presented to illustrate the effectiveness of the theoretical results.
Abstract: This paper examines the problem of designing a robust H∞ filter for a class of uncertain fuzzy descriptor systems described by a Takagi-Sugeno (TS) fuzzy model. Based on a linear matrix inequality (LMI) approach, LMI-based sufficient conditions for the uncertain nonlinear descriptor systems to have an H∞ performance are derived. To alleviate the ill-conditioning resulting from the interaction of slow and fast dynamic modes, solutions to the problem are given in terms of linear matrix inequalities which are independent of the singular perturbation ε, when ε is sufficiently small. The proposed approach does not involve the separation of states into slow and fast ones and it can be applied not only to standard, but also to nonstandard uncertain nonlinear descriptor systems. A numerical example is provided to illustrate the design developed in this paper.
Abstract: The effect of a uniform magnetic field on the
formation of drops of specific size has been investigated numerically
in a T-shaped microchannel. Previous researches indicated that the
drop sizes of secondary stream decreases, with increasing main
stream flow rate and decreasing interfacial tension. In the present
study the effect of a uniform magnetic field on the main stream is
considered, and it is proposed that by increasing the Hartmann
number, the size of the drops of the secondary stream will be
decreased.
Abstract: Worldwide conventional resources of fossil fuel are depleting very fast due to large scale increase in use of transport vehicles every year, therefore consumption rate of oil in transport sector alone has gone very high. In view of this, the major thrust has now been laid upon the search of alternative energy source and also for cost effective energy conversion system. The air converted into compressed form by non conventional or conventional methods can be utilized as potential working fluid for producing shaft work in the air turbine and thus offering the capability of being a zero pollution energy source. This paper deals with the mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine. Effect of expansion action and steady flow work in the air turbine at high admission air pressure of 6 bar, for varying injection to vane angles ratios 0.2-1.6, at the interval of 0.2 and at different vane angles such as 30o, 45o, 51.4o, 60o, 72o, 90o, and 120o for 12, 8, 7, 6, 5, 4 and 3 vanes respectively at speed of rotation 2500 rpm, has been quantified and analyzed here. Study shows that the expansion power has major contribution to total power, whereas the contribution of flow work output has been found varying only up to 19.4%. It is also concluded that for variation of injection to vane angle ratios from 0.2 to 1.2, the optimal power output is seen at vane angle 90o (4 vanes) and for 1.4 to 1.6 ratios, the optimal total power is observed at vane angle 72o (5 vanes). Thus in the vaned type novel air turbine the optimum shaft power output is developed when rotor contains 4-5 vanes for almost all situations of injection to vane angle ratios from 0.2 to 1.6.
Abstract: The use of contour strips of perennial vegetation with
bio-fuel potential can improve surface water quality by reducing
NO3-N and sediment outflow from cropland to surface water-bodies.
It also has economic benefits of producing ethanol. In this study,
The Soil and Water Assessment Tool (SWAT) model was applied to
a watershed in Iowa, USA to examine the effectiveness of contour
strips of switch grass in reducing the NO3-N outflows from crop
fields to rivers or lakes. Numerical experiments were conducted to
identify potential subbasins in the watershed that have high water
quality impact, and to examine the effects of strip size on NO3-N
reduction under various meteorological conditions, i.e. dry, average
and wet years. Useful information was obtained for the evaluation of
economic feasibility of growing switch grass for bio-fuel in contour
strips. The results can assist in cost-benefit analysis and decisionmaking
in best management practices for environmental protection.
Abstract: The present work is concerned with the free
convective two dimensional flow and heat transfer, in isotropic fluid
filled porous rectangular enclosure with differentially heated walls for
steady state incompressible flow have been investigated for non-
Darcy flow model. Effects of Darcy number (0.0001 £Da£ 10),
Rayleigh number (10 £Ra£ 5000), and aspect ratio (0.25 £AR£ 4), for
a range of porosity (0.4 £e£ 0.9) with and without moving lower wall
have been studied. The cavity was insulated at the lower and upper
surfaces. The right and left heated surfaces allows convective
transport through the porous medium, generating a thermal
stratification and flow circulations. It was found that the Darcy
number, Rayleigh number, aspect ratio, and porosity considerably
influenced characteristics of flow and heat transfer mechanisms. The
results obtained are discussed in terms of the Nusselt number,
vectors, contours, and isotherms.
Abstract: There is a world-wide need for the development of sustainable management strategies to control pest infestation and the development of phosphine (PH3) resistance in lesser grain borer (Rhyzopertha dominica). Computer simulation models can provide a relatively fast, safe and inexpensive way to weigh the merits of various management options. However, the usefulness of simulation models relies on the accurate estimation of important model parameters, such as mortality. Concentration and time of exposure are both important in determining mortality in response to a toxic agent. Recent research indicated the existence of two resistance phenotypes in R. dominica in Australia, weak and strong, and revealed that the presence of resistance alleles at two loci confers strong resistance, thus motivating the construction of a two-locus model of resistance. Experimental data sets on purified pest strains, each corresponding to a single genotype of our two-locus model, were also available. Hence it became possible to explicitly include mortalities of the different genotypes in the model. In this paper we described how we used two generalized linear models (GLM), probit and logistic models, to fit the available experimental data sets. We used a direct algebraic approach generalized inverse matrix technique, rather than the traditional maximum likelihood estimation, to estimate the model parameters. The results show that both probit and logistic models fit the data sets well but the former is much better in terms of small least squares (numerical) errors. Meanwhile, the generalized inverse matrix technique achieved similar accuracy results to those from the maximum likelihood estimation, but is less time consuming and computationally demanding.
Abstract: In this paper, the difference between the Alternating
Direction Method (ADM) and the Non-Splitting Method (NSM) is
investigated, while both methods applied to the simulations for 2-D
multimaterial radiation diffusion issues. Although the ADM have the
same accuracy orders with the NSM on the uniform meshes, the
accuracy of ADM will decrease on the distorted meshes or the
boundary of domain. Numerical experiments are carried out to
confirm the theoretical predication.
Abstract: Numerical study is performed to investigate the
temperature distribution in an annular diffuser fitted with helical tape
hub. Different pitches (Y = 20 mm, and Y = 30 mm) for the helical
tape are studied with different heights (H = 20 mm, 22 mm, and 24
mm) to be compared. The geometry of the annular diffuser and the
inlet condition for both hub arrangements are kept constant. The
result obtains that using helical tape insert with different pitches and
different heights will force the temperature to distribute in a helical
direction; however the use of helical tape hub with height (H = 22
mm) for both pitches enhance the temperature distribution in a good
manner.