Abstract: This paper presents the experimental results of silicone rubber outdoor polymer insulators in salt fog ageing test based on IEC 61109. Specimens made ofHTV silicone rubber with ATH content having three different configurations, straight shedsalternated sheds, and incline and alternate sheds, were tested continuously 1000 hrs.in artificial salt fog chamber. Contamination level, reduction of hydrophobicity and hardness measurement were used as physical damaged inspection techniques to evaluate degree of surface deterioration. In addition, chemical changing of tested specimen surface was evaluated by ATR-FTIRto confirm physical damaged inspection. After 1000 hrs.of salt fog test, differences in degree of surface deterioration were observed on all tested specimens. Physical damaged inspection and chemical analysis results confirmed the experimental results as well.
Abstract: Energy consumption is an important design issue for
Mobile Subscriber Station (MSS) in the standard IEEE 802.16e.
Because mobility of MSS implies that energy saving becomes an
issue so that lifetime of MSS can be extended before re-charging.
Also, the mechanism in efficiently managing the limited energy is
becoming very significant since a MSS is generally energized by
battery. For these, sleep mode operation is recently specified in the
MAC (Medium Access Control) protocol. In order to reduce the
energy consumption, we focus on the sleep-mode and wake-mode of
the MAC layer, which are included in the IEEE 802.16 standards [1-
2].
Abstract: SDMA (Space-Division Multiple Access) is a MIMO
(Multiple-Input and Multiple-Output) based wireless communication
network architecture which has the potential to significantly increase
the spectral efficiency and the system performance. The maximum
likelihood (ML) detection provides the optimal performance, but its
complexity increases exponentially with the constellation size of
modulation and number of users. The QR decomposition (QRD)
MUD can be a substitute to ML detection due its low complexity and
near optimal performance. The minimum mean-squared-error
(MMSE) multiuser detection (MUD) minimises the mean square
error (MSE), which may not give guarantee that the BER of the
system is also minimum. But the minimum bit error rate (MBER)
MUD performs better than the classic MMSE MUD in term of
minimum probability of error by directly minimising the BER cost
function. Also the MBER MUD is able to support more users than
the number of receiving antennas, whereas the rest of MUDs fail in
this scenario. In this paper the performance of various MUD
techniques is verified for the correlated MIMO channel models based
on IEEE 802.16n standard.
Abstract: Numerical investigation of the characteristics of an 80°
delta wing in combined force-pitch and free-roll is presented. The
implicit, upwind, flux-difference splitting, finite volume scheme and
the second-order-accurate finite difference scheme are employed to
solve the flow governing equations and Euler rigid-body dynamics
equations, respectively. The characteristics of the delta wing in
combined free-roll and large amplitude force-pitch is obtained
numerically and shows a well agreement with experimental data
qualitatively. The motion in combined force-pitch and free-roll
significantly reduces the lift force and transverse stabilities of the delta
wing, which is closely related to the flying safety. Investigations on
sensitive factors indicate that the roll-axis moment of inertia and the
structural damping have great influence on the frequency and
amplitude, respectively. Moreover, the turbulence model is considered
as an influencing factor in the investigation.
Abstract: This paper presents an optimization of the hull
separation, i.e. transverse clearance. The main objective is to identify
the feasible speed ranges and find the optimum transverse clearance
considering the minimum wave-making resistance. The dimensions
and the weight of hardware systems installed in the catamaran
structured fuel cell powered USV (Unmanned Surface Vehicle) were
considered as constraints. As the CAE (Computer Aided Engineering)
platform FRIENDSHIP-Framework was used. The hull surface
modeling, DoE (Design of Experiment), Tangent search optimization,
tool integration and the process automation were performed by
FRIENDSHIP-Framework. The hydrodynamic result was evaluated
by XPAN the potential solver of SHIPFLOW.
Abstract: General as well as the MSW management in Thailand is reviewed in this paper. Topics include the MSW generation, sources, composition, and trends. The review, then, moves to sustainable solutions for MSW management, sustainable alternative approaches with an emphasis on an integrated MSW management. Information of waste in Thailand is also given at the beginning of this paper for better understanding of later contents. It is clear that no one single method of MSW disposal can deal with all materials in an environmentally sustainable way. As such, a suitable approach in MSW management should be an integrated approach that could deliver both environmental and economic sustainability. With increasing environmental concerns, the integrated MSW management system has a potential to maximize the useable waste materials as well as produce energy as a by-product. In Thailand, the compositions of waste (86%) are mainly organic waste, paper, plastic, glass, and metal. As a result, the waste in Thailand is suitable for an integrated MSW management. Currently, the Thai national waste management policy starts to encourage the local administrations to gather into clusters to establish central MSW disposal facilities with suitable technologies and reducing the disposal cost based on the amount of MSW generated.
Abstract: This paper studies the dependability of componentbased
applications, especially embedded ones, from the diagnosis
point of view. The principle of the diagnosis technique is to
implement inter-component tests in order to detect and locate the
faulty components without redundancy. The proposed approach for
diagnosing faulty components consists of two main aspects. The first
one concerns the execution of the inter-component tests which
requires integrating test functionality within a component. This is the
subject of this paper. The second one is the diagnosis process itself
which consists of the analysis of inter-component test results to
determine the fault-state of the whole system. Advantage of this
diagnosis method when compared to classical redundancy faulttolerant
techniques are application autonomy, cost-effectiveness and
better usage of system resources. Such advantage is very important
for many systems and especially for embedded ones.
Abstract: It is known that symmetric encryption algorithms are
fast and easy to implement in hardware. Also elliptic curves have
proved to be a good choice for building encryption system. Although
most of the symmetric systems have been broken, we can create a
hybrid system that has the same properties of the symmetric
encryption systems and in the same time, it has the strength of
elliptic curves in encryption. As DES algorithm is considered the
core of all successive symmetric encryption systems, we modified
DES using elliptic curves and built a new DES algorithm that is hard
to be broken and will be the core for all other symmetric systems.
Abstract: In this paper, an automated algorithm to estimate and remove the continuous baseline from measured spectra containing both continuous and discontinuous bands is proposed. The algorithm uses previous information contained in a Continuous Database Spectra (CDBS) to obtain a linear basis, with minimum number of sampled vectors, capable of representing a continuous baseline. The proposed algorithm was tested by using a CDBS of flame spectra where Principal Components Analysis and Non-negative Matrix Factorization were used to obtain linear bases. Thus, the radical emissions of natural gas, oil and bio-oil flames spectra at different combustion conditions were obtained. In order to validate the performance in the baseline estimation process, the Goodness-of-fit Coefficient and the Root Mean-squared Error quality metrics were evaluated between the estimated and the real spectra in absence of discontinuous emission. The achieved results make the proposed method a key element in the development of automatic monitoring processes strategies involving discontinuous spectral bands.
Abstract: Sensor relocation is to repair coverage holes caused by node failures. One way to repair coverage holes is to find redundant nodes to replace faulty nodes. Most researches took a long time to find redundant nodes since they randomly scattered redundant nodes around the sensing field. To record the precise position of sensor nodes, most researches assumed that GPS was installed in sensor nodes. However, high costs and power-consumptions of GPS are heavy burdens for sensor nodes. Thus, we propose a fast sensor relocation algorithm to arrange redundant nodes to form redundant walls without GPS. Redundant walls are constructed in the position where the average distance to each sensor node is the shortest. Redundant walls can guide sensor nodes to find redundant nodes in the minimum time. Simulation results show that our algorithm can find the proper redundant node in the minimum time and reduce the relocation time with low message complexity.
Abstract: A long-term campaign for monitoring the
concentration of atmospheric Particulate Matter (PM) was conducted
at multiple sites located in the center and suburbs of the Tokyo
Metropolitan Area in Japan. The concentration of fine PM has shown a
declining trend over the last two decades. A positive matrix
factorization model elucidated that the contribution of combustion
sources was drastically reduced. In Japan, the regulations on vehicle
exhaust emissions were phased in and gradually tightened over the last
two decades, which has triggered a notable reduction in PM emissions
from automobiles and has contributed to the mitigation of the problem
of fine PM pollution.
Abstract: This project focuses on the development of a line
follower algorithm for a Two Wheels Balancing Robot. In this
project, ATMEGA32 is chosen as the brain board controller to react
towards the data received from Balance Processor Chip on the
balance board to monitor the changes of the environment through
two infra-red distance sensor to solve the inclination angle problem.
Hence, the system will immediately restore to the set point (balance
position) through the implementation of internal PID algorithms at
the balance board. Application of infra-red light sensors with the PID
control is vital, in order to develop a smooth line follower robot. As a
result of combination between line follower program and internal self
balancing algorithms, we are able to develop a dynamically
stabilized balancing robot with line follower function.
Abstract: This paper presents the design and analysis of a parallel
connected inverter configuration of. The configuration consists of
parallel connected three-phase dc/ac inverter. Series resistors added
to the inverter output to maintain same current in each inverter of the
two parallel inverters, and to reduce the circulating current in the
parallel inverters to the minimum. High frequency third harmonic
injection PWM (THIPWM) employed to reduce the total harmonic
distortion and to make maximum use of the voltage source. DSP was
used to generate the THIPWM and the control algorithm for the
converter. Selected experimental results have been shown to validate
the proposed system.
Abstract: Recently, Thai education system is engaged in serious and promising reforms. One of the crucial elements in most of these educational reforms is the teacher professional development. Teachers today are under growing pressure to perform. However, most new teachers are not adequately prepared to meet the expectation. Consequently, this paper seeks to investigate the opinion of mentor teachers and university supervisors about professional development in the aspect of learning management skill of the preservice teachers in Rajabhat Universities, then compare the opinion between the mentor teachers and university supervisors about professional development in the aspect of learning management skill of the pre-service teachers. The study involved a cohort of 40 university supervisors and 77 mentor teachers. The research concludes by showing that mentor teachers viewed pre-service teacher as a professional teacher with an effective learning management skill. However, in the perspective of the university supervisor, pre-service teachers still have inadequate learning management skill.
Abstract: Microparticles carrier systems made from naturally occurring polymers based on chitosan/casein system appears to be a promising carrier for the sustained release of orally and parenteral administered drugs. In the current study we followed a microencapsulation technique based aqueous coacervation method to prepare chitosan/casein microparticles of compositions 1:1, 1:2 and 1:5 incorporated with chloramphenicol. Glutaraldehyde was used as a chemical cross-linking agent. The microparticles were prepared by aerosol method and studied by optical microscopy, infrared spectroscopy, thermo gravimetric analysis, swelling studies and drug release studies at various pH. The percentage swelling of the polymers are found to be in the order pH 4 > pH 10 > pH 7 and the increase in casein composition decrease the swelling percentage. The drug release studies also follow the above order.
Abstract: The desulfurization of coal using biological methods is an emerging technology. The biodesulfurization process uses the catalytic activity of chemolithotrophic acidpohiles in removing sulfur and pyrite from the coal. The present study was undertaken to examine the potential of Acidithiobacillus ferrooxidans in removing the pyritic sulfur and iron from high iron and sulfur containing US coal. The experiment was undertaken in 10 L batch stirred tank reactor having 10% pulp density of coal. The reactor was operated under mesophilic conditions and aerobic conditions were maintained by sparging the air into the reactor. After 35 days of experiment, about 64% of pyrite and 21% of pyritic sulfur was removed from the coal. The findings of the present study indicate that the biodesulfurization process does have potential in treating the high pyrite and sulfur containing coal. A good mass balance was also obtained with net loss of about 5% showing its feasibility for large scale application.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: The main objective of Automatic Generation Control (AGC) is to balance the total system generation against system load losses so that the desired frequency and power interchange with neighboring systems is maintained. Any mismatch between generation and demand causes the system frequency to deviate from its nominal value. Thus high frequency deviation may lead to system collapse. This necessitates a very fast and accurate controller to maintain the nominal system frequency. This paper deals with a novel approach of artificial intelligence (AI) technique called Hybrid Neuro-Fuzzy (HNF) approach for an (AGC). The advantage of this controller is that it can handle the non-linearities at the same time it is faster than other conventional controllers. The effectiveness of the proposed controller in increasing the damping of local and inter area modes of oscillation is demonstrated in a two area interconnected power system. The result shows that intelligent controller is having improved dynamic response and at the same time faster than conventional controller.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Network on Chip (NoC) has emerged as a promising
on chip communication infrastructure. Three Dimensional Integrate
Circuit (3D IC) provides small interconnection length between layers
and the interconnect scalability in the third dimension, which can
further improve the performance of NoC. Therefore, in this paper,
a hierarchical cluster-based interconnect architecture is merged with
the 3D IC. This interconnect architecture significantly reduces the
number of long wires. Since this architecture only has approximately
a quarter of routers in 3D mesh-based architecture, the average
number of hops is smaller, which leads to lower latency and higher
throughput. Moreover, smaller number of routers decreases the area
overhead. Meanwhile, some dual links are inserted into the bottlenecks
of communication to improve the performance of NoC.
Simulation results demonstrate our theoretical analysis and show the
advantages of our proposed architecture in latency, throughput and
area, when compared with 3D mesh-based architecture.