Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Continuously growing needs for Internet applications
that transmit massive amount of data have led to the emergence of
high speed network. Data transfer must take place without any
congestion and hence feedback parameters must be transferred from
the receiver end to the sender end so as to restrict the sending rate in
order to avoid congestion. Even though TCP tries to avoid
congestion by restricting the sending rate and window size, it never
announces the sender about the capacity of the data to be sent and
also it reduces the window size by half at the time of congestion
therefore resulting in the decrease of throughput, low utilization of
the bandwidth and maximum delay. In this paper, XCP protocol is
used and feedback parameters are calculated based on arrival rate,
service rate, traffic rate and queue size and hence the receiver
informs the sender about the throughput, capacity of the data to be
sent and window size adjustment, resulting in no drastic decrease in
window size, better increase in sending rate because of which there is
a continuous flow of data without congestion. Therefore as a result of
this, there is a maximum increase in throughput, high utilization of
the bandwidth and minimum delay. The result of the proposed work
is presented as a graph based on throughput, delay and window size.
Thus in this paper, XCP protocol is well illustrated and the various
parameters are thoroughly analyzed and adequately presented.
Abstract: In this paper, we focus on the fusion of images from
different sources using multiresolution wavelet transforms. Based on
reviews of popular image fusion techniques used in data analysis,
different pixel and energy based methods are experimented. A novel
architecture with a hybrid algorithm is proposed which applies pixel
based maximum selection rule to low frequency approximations and
filter mask based fusion to high frequency details of wavelet
decomposition. The key feature of hybrid architecture is the
combination of advantages of pixel and region based fusion in a
single image which can help the development of sophisticated
algorithms enhancing the edges and structural details. A Graphical
User Interface is developed for image fusion to make the research
outcomes available to the end user. To utilize GUI capabilities for
medical, industrial and commercial activities without MATLAB
installation, a standalone executable application is also developed
using Matlab Compiler Runtime.
Abstract: Imprecision is a long-standing problem in CAD design
and high accuracy image-based reconstruction applications. The visual
hull which is the closed silhouette equivalent shape of the objects
of interest is an important concept in image-based reconstruction.
We extend the domain-theoretic framework, which is a robust and
imprecision capturing geometric model, to analyze the imprecision in
the output shape when the input vertices are given with imprecision.
Under this framework, we show an efficient algorithm to generate the
2D partial visual hull which represents the exact information of the
visual hull with only basic imprecision assumptions. We also show
how the visual hull from polyhedra problem can be efficiently solved
in the context of imprecise input.
Abstract: The steam cracking reactions are always accompanied with the formation of coke which deposits on the walls of the tubular reactors. The investigation has attempted to control catalytic coking by the applying aluminum, zinc and ceramic coating like aluminum-magnesium by thermal spray and pack cementation method. Rate of coke formation during steam cracking of naphtha has been investigated both for uncoated stainless steel (with different alloys) and metal coating constructed with thermal Spray and pack cementation method with metal powders of Aluminum, Aluminum-Magnesium, zinc, silicon, nickel and chromium. The results of the study show that passivating the surface of SS321 with a coating of Aluminum and Aluminum-Magnesium can significantly reduce the rate of coke deposition during naphtha pyrolysis. SEM and EDAX techniques (Philips XL Series) were used to examine the coke deposits formed by the metal-hydrocarbon reactions. Our objective was to separate the different stages by identifying the characteristic morphologies.
Abstract: The connection between solar activity and adverse phenomena in the Earth’s environment that can affect space and ground based technologies has spurred interest in Space Weather (SW) research. A great effort has been put on the development of suitable models that can provide advanced forecast of SW events. With the progress in computational technology, it is becoming possible to develop operational large scale physics based models which can incorporate the most important physical processes and domains of the Sun-Earth system. In order to enhance our SW prediction capabilities we are developing advanced numerical tools. With operational requirements in mind, our goal is to develop a modular simulation framework of propagation of the disturbances from the Sun through interplanetary space to the Earth. Here, we report and discuss on the development of coronal field and solar wind components for a large scale MHD code. The model for these components is based on a potential field source surface model and an empirical Wang-Sheeley-Arge solar wind relation.
Abstract: Fast development of technologies, economic globalization and many other external circumstances stimulate company’s competitiveness. One of the major trends in today’s business is the shift to the exploitation of the Internet and electronic environment for entrepreneurial needs. Latest researches confirm that e-environment provides a range of possibilities and opportunities for companies, especially for micro-, small- and medium-sized companies, which have limited resources. The usage of e-tools raises the effectiveness and the profitability of an organization, as well as its competitiveness.
In the electronic market, as in the classic one, there are factors, such as globalization, development of new technology, price sensitive consumers, Internet, new distribution and communication channels that influence entrepreneurship. As a result of eenvironment development, e-commerce and e-marketing grow as well.
Objective of the paper: To describe and identify factors influencing company’s competitiveness in e-environment.
Research methodology: The authors employ well-established quantitative and qualitative methods of research: grouping, analysis, statistics method, factor analysis in SPSS 20 environment, etc. The theoretical and methodological background of the research is formed by using scientific researches and publications, such as that from mass media and professional literature; statistical information from legal institutions as well as information collected by the authors during the surveying process.
Research result: The authors detected and classified factors influencing competitiveness in e-environment.
In this paper, the authors presented their findings based on theoretical, scientific, and field research. Authors have conducted a research on e-environment utilization among Latvian enterprises.
Abstract: On-line (near infrared) spectroscopy is widely used to support the operation of complex process systems. Information extracted from spectral database can be used to estimate unmeasured product properties and monitor the operation of the process. These techniques are based on looking for similar spectra by nearest neighborhood algorithms and distance based searching methods. Search for nearest neighbors in the spectral space is an NP-hard problem, the computational complexity increases by the number of points in the discrete spectrum and the number of samples in the database. To reduce the calculation time some kind of indexing could be used. The main idea presented in this paper is to combine indexing and visualization techniques to reduce the computational requirement of estimation algorithms by providing a two dimensional indexing that can also be used to visualize the structure of the spectral database. This 2D visualization of spectral database does not only support application of distance and similarity based techniques but enables the utilization of advanced clustering and prediction algorithms based on the Delaunay tessellation of the mapped spectral space. This means the prediction has not to use the high dimension space but can be based on the mapped space too. The results illustrate that the proposed method is able to segment (cluster) spectral databases and detect outliers that are not suitable for instance based learning algorithms.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: Silver nanoparticles were prepared by chemical reduction method. Silver nitrate was taken as the metal precursor and hydrazine hydrate as a reducing agent. The formation of the silver nanoparticles was monitored using UV-Vis absorption spectroscopy. The UV-Vis spectroscopy revealed the formation of silver nanopart├¡cles by exhibing the typical surface plasmon absorption maxima at 418-420 nm from the UV–Vis spectrum. Comparison of theoretical (Mie light scattering theory) and experimental results showed that diameter of silver nanoparticles in colloidal solution is about 60 nm. We have used energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM) and, UV–Vis spectroscopy to characterize the nanoparticles obtained. The energy-dispersive spectroscopy (EDX) of the nanoparticles dispersion confirmed the presence of elemental silver signal no peaks of other impurity were detected. The average size and morphology of silver nanoparticles were determined by transmission electron microscopy (TEM). TEM photographs indicate that the nanopowders consist of well dispersed agglomerates of grains with a narrow size distribution (40 and 60 nm), whereas the radius of the individual particles are between 10 and 20 nm. The synthesized nanoparticles have been structurally characterized by X-ray diffraction and transmission high-energy electron diffraction (HEED). The peaks in the XRD pattern are in good agreement with the standard values of the face-centered-cubic form of metallic silver (ICCD-JCPDS card no. 4-0787) and no peaks of other impurity crystalline phases were detected. Additionally, the antibacterial activity of the nanopart├¡culas dispersion was measured by Kirby-Bauer method. The nanoparticles of silver showed high antimicrobial and bactericidal activity against gram positive bacteria such as Escherichia Coli, Pseudimonas aureginosa and staphylococcus aureus which is a highly methicillin resistant strain.
Abstract: In the current study, we have conducted an experimental investigation on the utilization of electronic arc furnace (EAF) reducing slag for the absorption of CO2 via wet grinding method. It was carried out by various grinding conditions. The slag was ground in the vibrating ball mill in the presence of CO2 and pure water under ambient temperature. The reaction behavior was monitored with constant pressure method, and the changes of experimental systems volume as a function of grinding time were measured. It was found that the CO2 absorption occurred as soon as the grinding started. The CO2 absorption was significantly increased in the case of wet grinding compare to the dry grinding. Generally, the amount of CO2 absorption increased as the amount of water, weight of slag and initial pressure increased. However, it was decreased when the amount of water exceeds 200ml and when smaller balls were used. The absorption of CO2 occurred simultaneously with the start of the grinding and it stopped when the grinding was stopped. According to this research, the CO2 reacted with the CaO inside the slag, forming CaCO3.
Abstract: There has been a growing emphasis in
communication management from simple coordination of
promotional tools to a complex strategic process. This study will
examine the current marketing communications and engagement
strategies used in addressing the key stakeholders. In the case of
fertilizer industry in Malaysia, there has been little empirical
research on stakeholder communication when major challenges
facing the modern corporation is the need to communicate its
identity, its values and products in order to distinguish itself from
competitors. The study will employ both quantitative and qualitative
methods and the use of Structural Equation Modeling (SEM) to
establish a causal relationship amongst the key factors of stakeholder
communication strategies and increment in consumers-
choice/acceptance and impact on financial performance. One of the
major contributions is a conceptual framework for communication
strategies and engagement in increasing consumers- acceptance level
and the firm-s financial performance.
Abstract: Thisresearch paper is dedicated to an actual issue in Latvia and in the whole European Union – development of the secondary materials management. The goal of this paper is to research the development of the secondary materials management in Latvia as a result to point out its main positive aspects and problems. In this research paper the author regards following issues: significance of the secondary materials management, current situation of the waste generation and utilization in Latvia comparing with other EU Member States, main problems and positive aspects of the secondary materials management in Latvia. The research author concludes that in last ten years a great work is done to develop the secondary materials market. Nevertheless following improvements are necessary: implementation of the packaging deposit system, development of the separate waste collection, increasing of the recycling capacity.
Abstract: This study aims to examine the factors affecting
knowledge sharing behavior in knowledge-based electronic communities (e-communities) because quantity and quality of
knowledge shared among the members play a critical role in the community-s sustainability. Past research has suggested three
perspectives that may affect the quantity and quality of knowledge
shared: economics, social psychology, and social ecology. In this
study, we strongly believe that an economic perspective may be suitable to validate factors influencing newly registered members-
knowledge contribution at the beginning of relationship development.
Accordingly, this study proposes a model to validate the factors influencing members- knowledge sharing based on Transaction Cost
Theory. By doing so, we may empirically test our hypotheses in various types of e-communities to determine the generalizability of our research models.
Abstract: This paper presents an architecture of current filesystem
implementations as well as our new filesystem SpadFS and operating
system Spad with rewritten VFS layer targeted at high performance
I/O applications. The paper presents microbenchmarks and real-world
benchmarks of different filesystems on the same kernel as well as
benchmarks of the same filesystem on different kernels – enabling
the reader to make conclusion how much is the performance of
various tasks affected by operating system and how much by physical
layout of data on disk. The paper describes our novel features–most
notably continuous allocation of directories and cross-file readahead
– and shows their impact on performance.
Abstract: Although water only takes a little percentage in the total mass of soil, it indeed plays an important role to the strength of structure. Moisture transfer can be carried out by many different mechanisms which may involve heat and mass transfer, thermodynamic phase change, and the interplay of various forces such as viscous, buoyancy, and capillary forces. The continuum models are not well suited for describing those phenomena in which the connectivity of the pore space or the fracture network, or that of a fluid phase, plays a major role. However, Lattice Boltzmann methods (LBMs) are especially well suited to simulate flows around complex geometries. Lattice Boltzmann methods were initially invented for solving fluid flows. Recently, fluid with multicomponent and phase change is also included in the equations. By comparing the numerical result with experimental result, the Lattice Boltzmann methods with phase change will be optimized.
Abstract: Adsorption of methanol and ethanol over mesoporous
siliceous material are studied in the current paper. The pure
mesoporous silica is prepared using tetraethylorthosilicate (TEOS) as
silica source and dodecylamine as template at low pH. The prepared
material was characterized using nitrogen adsorption,nX-ray
diffraction (XRD) and scanning electron microscopy (SEM). The
adsorption kinetics of methanol and ethanol from aqueous solution
were studied over the prepared mesoporous silica material. The
percent removal of alcohol was calculated per unit mass of adsorbent
used. The 1st order model is found to be in agreement with both
adsorbates while the 2nd order model fit the adsorption of methanol
only.
Abstract: The objective of the present study was to examine the
dose-response relationships between antioxidant parameters and liver
contaminant levels of Kazakhstan light crude oil (KLCO) in albino
rats. The animals were repeatedly exposed, by intraperitoneal
injection, to low dosages (0.5–1.5 ml/kg) of KLCO. Rats exposed to
these doses levels did not show any apparent symptoms of
intoxication. Serum aminotransferases increased significantly
(p
Abstract: The growing importance of sustainability in corporate
policies represents a great opportunity for workers to gain more
consideration, with great benefits to their well being. Sustainable
work is believed to be one which improves the organization-s
performance and fosters professional development as well as
workers- health. In a multiple case study based on document
research, information was sought about work activities and their
sustainability or corporate social responsibility (CSR) policies, as
disseminated by corporations. All the companies devoted attention to
work activities and delivered a good amount of information about
them. Nevertheless, the information presented was generic; all the
actions developed were top-down and there was no information about
the impact of changes aimed at sustainability on the workers-
activities. It was found that the companies seemed to be at an early
stage. In the future, they need to show more commitment through
concrete goals: they must be aware that workers contribute directly to
the corporations- sustainability. This would allow room for
Ergonomics and Work Psychodynamics to be incorporated and to be
useful for both companies and society, so as to promote and ensure
work sustainability.
Abstract: The aim of the work presented here was to either use
existing forest dynamic simulation models or calibrate a new one
both within the SYMFOR framework with the purpose of examining
changes in stand level basal area and functional composition in
response to selective logging considering trees > 10 cm d.b.h for two
areas of undisturbed Amazonian non flooded tropical forest in Brazil
and one in Peru. Model biological realism was evaluated for forest in
the undisturbed and selectively logged state and it was concluded that
forest dynamics were realistically represented. Results of the logging
simulation experiments showed that in relation to undisturbed forest
simulation subject to no form of harvesting intervention there was a
significant amount of change over a 90 year simulation period that
was positively proportional to the intensity of logging. Areas which
had in the dynamic equilibrium of undisturbed forest a greater
proportion of a specific ecological guild of trees known as the light
hardwoods (LHW’s) seemed to respond more favorably in terms of
less deviation but only within a specific range of baseline forest
composition beyond which compositional diversity became more
important. These finds are in line partially with practical management
experience and partiality basic systematics theory respectively.