Abstract: BER analysis of Impulse Radio Ultra Wideband (IRUWB) pulse modulations over S-V channel model is proposed in this paper. The UWB pulse is Gaussian monocycle pulse modulated using Pulse Amplitude Modulation (PAM) and Pulse Position Modulation (PPM). The channel model is generated from a modified S-V model. Bit-error rate (BER) is measured over several of bit rates. The result shows that all modulation are appropriate for both LOS and NLOS channel, but PAM gives better performance in bit rates and SNR. Moreover, as standard of speed has been given for UWB, the communication is appropriate with high bit rates in LOS channel.
Abstract: Performance control law is studied for an
interconnected fractional nonlinear system. Applying a backstepping
algorithm, a backstepping sliding mode controller (BSMC) is
developed for fractional nonlinear system. To improve control law
performance, BSMC is coupled to an adaptive sliding mode observer
have a filtered error as a sliding surface. The both architecture
performance is studied throughout the inverted pendulum mounted on
a cart. Simulation result show that the BSMC coupled to an adaptive
sliding mode observer have stable control law and eligible control
amplitude than the BSMC.
Abstract: The rapid growth of e-Commerce services is
significantly observed in the past decade. However, the method to
verify the authenticated users still widely depends on numeric
approaches. A new search on other verification methods suitable for
online e-Commerce is an interesting issue. In this paper, a new online
signature-verification method using angular transformation is
presented. Delay shifts existing in online signatures are estimated by
the estimation method relying on angle representation. In the
proposed signature-verification algorithm, all components of input
signature are extracted by considering the discontinuous break points
on the stream of angular values. Then the estimated delay shift is
captured by comparing with the selected reference signature and the
error matching can be computed as a main feature used for verifying
process. The threshold offsets are calculated by two types of error
characteristics of the signature verification problem, False Rejection
Rate (FRR) and False Acceptance Rate (FAR). The level of these two
error rates depends on the decision threshold chosen whose value is
such as to realize the Equal Error Rate (EER; FAR = FRR). The
experimental results show that through the simple programming,
employed on Internet for demonstrating e-Commerce services, the
proposed method can provide 95.39% correct verifications and 7%
better than DP matching based signature-verification method. In
addition, the signature verification with extracting components
provides more reliable results than using a whole decision making.
Abstract: In this paper, an H1-Galerkin mixed finite element method is discussed for the coupled Burgers equations. The optimal error estimates of the semi-discrete and fully discrete schemes of the coupled Burgers equation are derived.
Abstract: The error diffusion method generates worm artifacts,
and weakens the edge of the halftone image when the continuous gray
scale image is reproduced by a binary image. First, to enhance the
edges, we propose the edge-enhancing filter by considering the
quantization error information and gradient of the neighboring pixels.
Furthermore, to remove worm artifacts often appearing in a halftone
image, we add adaptively random noise into the weights of an error
filter.
Abstract: Hexapod Machine Tool (HMT) is a parallel robot
mostly based on Stewart platform. Identification of kinematic
parameters of HMT is an important step of calibration procedure. In
this paper an algorithm is presented for identifying the kinematic
parameters of HMT using inverse kinematics error model. Based on
this algorithm, the calibration procedure is simulated. Measurement
configurations with maximum observability are decided as the first
step of this algorithm for a robust calibration. The errors occurring in
various configurations are illustrated graphically. It has been shown
that the boundaries of the workspace should be searched for the
maximum observability of errors. The importance of using
configurations with sufficient observability in calibrating hexapod
machine tools is verified by trial calibration with two different
groups of randomly selected configurations. One group is selected to
have sufficient observability and the other is in disregard of the
observability criterion. Simulation results confirm the validity of the
proposed identification algorithm.
Abstract: In this paper, we evaluate the performance of some wavelet based coding algorithms such as 3D QT-L, 3D SPIHT and JPEG2K. In the first step we achieve an objective comparison between three coders, namely 3D SPIHT, 3D QT-L and JPEG2K. For this purpose, eight MRI head scan test sets of 256 x 256x124 voxels have been used. Results show superior performance of 3D SPIHT algorithm, whereas 3D QT-L outperforms JPEG2K. The second step consists of evaluating the robustness of 3D SPIHT and JPEG2K coding algorithm over wireless transmission. Compressed dataset images are then transmitted over AWGN wireless channel or over Rayleigh wireless channel. Results show the superiority of JPEG2K over these two models. In fact, it has been deduced that JPEG2K is more robust regarding coding errors. Thus we may conclude the necessity of using corrector codes in order to protect the transmitted medical information.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Rotating stages in semiconductor, display industry and many other fields require challenging accuracy to perform their functions properly. Especially, Axis of rotation error on rotary system is significant; such as the spindle error motion of the aligner, wire bonder and inspector machine which result in the poor state of manufactured goods. To evaluate and improve the performance of such precision rotary stage, unessential movements on the other 5 degrees of freedom of the rotary stage must be measured and analyzed. In this paper, we have measured the three translations and two tilt motions of a rotating stage with high precision capacitive sensors. To obtain the radial error motion from T.I.R (Total Indicated Reading) of radial direction, we have used Donaldson's reversal technique. And the axial components of the spindle tilt error motion can be obtained accurately from the axial direction outputs of sensors by Estler face motion reversal technique. Further more we have defined and measured the sensitivity of positioning error to the five error motions.
Abstract: This study is to investigate the electroencephalogram (EEG) differences generated from a normal and Alzheimer-s disease (AD) sources. We also investigate the effects of brain tissue distortions due to AD on EEG. We develop a realistic head model from T1 weighted magnetic resonance imaging (MRI) using finite element method (FEM) for normal source (somatosensory cortex (SC) in parietal lobe) and AD sources (right amygdala (RA) and left amygdala (LA) in medial temporal lobe). Then, we compare the AD sourced EEGs to the SC sourced EEG for studying the nature of potential changes due to sources and 5% to 20% brain tissue distortions. We find an average of 0.15 magnification errors produced by AD sourced EEGs. Different brain tissue distortion models also generate the maximum 0.07 magnification. EEGs obtained from AD sources and different brain tissue distortion levels vary scalp potentials from normal source, and the electrodes residing in parietal and temporal lobes are more sensitive than other electrodes for AD sourced EEG.
Abstract: In present work the problem of the ITER fusion
plasma neutron source parameter reconstruction using only the
Vertical Neutron Camera data was solved. The possibility of neutron
source parameter reconstruction was estimated by the numerical
simulations and the analysis of adequateness of mathematic model
was performed. The neutron source was specified in a parametric
form. The numerical analysis of solution stability with respect to data
distortion was done. The influence of the data errors on the
reconstructed parameters is shown:
• is reconstructed with errors less than 4% at all examined values
of δ (until 60%);
• is determined with errors less than 10% when δ do not overcome
5%;
• is reconstructed with relative error more than 10 %;
• integral intensity of the neutron source is determined with error
10% while δ error is less than 15%;
where -error of signal measurements, (R0,Z0), the plasma center
position,- /parameter of neutron source profile.
Abstract: The composition, vapour pressure, and heat capacity
of nine biodiesel fuels from different sources were measured. The
vapour pressure of the biodiesel fuels is modeled assuming an ideal
liquid phase of the fatty acid methyl esters constituting the fuel. New
methodologies to calculate the vapour pressure and ideal gas and
liquid heat capacities of the biodiesel fuel constituents are proposed.
Two alternative optimization scenarios are evaluated: 1) vapour
pressure only; 2) vapour pressure constrained with liquid heat
capacity. Without physical constraints, significant errors in liquid
heat capacity predictions were found whereas the constrained
correlation accurately fit both vapour pressure and liquid heat
capacity.
Abstract: In this paper parametric analytical studies have been carried out to examine the intrinsic flow physics pertaining to the liftoff time of solid propellant rockets. Idealized inert simulators of solid rockets are selected for numerical studies to examining the preignition chamber dynamics. Detailed diagnostic investigations have been carried out using an unsteady two-dimensional k-omega turbulence model. We conjectured from the numerical results that the altered variations of the igniter jet impingement angle, turbulence level, time and location of the first ignition, flame spread characteristics, the overall chamber dynamics including the boundary layer growth history are having bearing on the time for nozzle flow chocking for establishing the required thrust for the rocket liftoff. We concluded that the altered flow choking time of strap-on motors with the pre-determined identical ignition time at the lift off phase will lead to the malfunctioning of the rocket. We also concluded that, in the light of the space debris, an error in predicting the liftoff time can lead to an unfavorable launch window amounts the satellite injection errors and/or the mission failures.
Abstract: A theory for optimal filtering of infinite sets of random
signals is presented. There are several new distinctive features of the
proposed approach. First, a single optimal filter for processing any
signal from a given infinite signal set is provided. Second, the filter is
presented in the special form of a sum with p terms where each term
is represented as a combination of three operations. Each operation
is a special stage of the filtering aimed at facilitating the associated
numerical work. Third, an iterative scheme is implemented into the
filter structure to provide an improvement in the filter performance at
each step of the scheme. The final step of the scheme concerns signal
compression and decompression. This step is based on the solution of
a new rank-constrained matrix approximation problem. The solution
to the matrix problem is described in this paper. A rigorous error
analysis is given for the new filter.
Abstract: Longitudinal data typically have the characteristics of
changes over time, nonlinear growth patterns, between-subjects
variability, and the within errors exhibiting heteroscedasticity and
dependence. The data exploration is more complicated than that of
cross-sectional data. The purpose of this paper is to organize/integrate
of various visual-graphical techniques to explore longitudinal data.
From the application of the proposed methods, investigators can
answer the research questions include characterizing or describing the
growth patterns at both group and individual level, identifying the time
points where important changes occur and unusual subjects, selecting
suitable statistical models, and suggesting possible within-error
variance.
Abstract: Bus networks design is an important problem in
public transportation. The main step to this design, is determining the
number of required terminals and their locations. This is an especial
type of facility location problem, a large scale combinatorial
optimization problem that requires a long time to be solved.
The genetic algorithm (GA) is a search and optimization technique
which works based on evolutionary principle of natural
chromosomes. Specifically, the evolution of chromosomes due to the
action of crossover, mutation and natural selection of chromosomes
based on Darwin's survival-of-the-fittest principle, are all artificially
simulated to constitute a robust search and optimization procedure.
In this paper, we first state the problem as a mixed integer
programming (MIP) problem. Then we design a new crossover and
mutation for bus terminal location problem (BTLP). We tested the
different parameters of genetic algorithm (for a sample problem) and
obtained the optimal parameters for solving BTLP with numerical try
and error.
Abstract: Thirty three re-wetting tests were conducted at
different combinations of temperatures (5.7- 46.30C) and relative
humidites (48.2-88.6%) with barley. Two most commonly used thinlayer
drying and rewetting models i.e. Page and Diffusion were
compared for their ability to the fit the experimental re-wetting data
based on the standard error of estimate (SEE) of the measured and
simulated moisture contents. The comparison shows both the Page
and Diffusion models fit the re-wetting experimental data of barley
well. The average SEE values for the Page and Diffusion models
were 0.176 % d.b. and 0.199 % d.b., respectively. The Page and
Diffusion models were found to be most suitable equations, to
describe the thin-layer re-wetting characteristics of barley over a
typically five day re-wetting. These two models can be used for the
simulation of deep-bed re-wetting of barley occurring during
ventilated storage and deep bed drying.
Abstract: A subsea hydrocarbon production system can undergo planned and unplanned shutdowns during the life of the field. The thermal FEA is used to simulate the cool down to verify the insulation design of the subsea equipment, but it is also used to derive an acceptable insulation design for the cold spots. The driving factors of subsea analyses require fast responding and accurate models of the equipment cool down. This paper presents cool down analysis carried out by a Krylov subspace reduction method, and compares this approach to the commonly used FEA solvers. The model considered represents a typical component of a subsea production system, a closed valve on a dead leg. The results from the Krylov reduction method exhibits the least error and requires the shortest computational time to reach the solution. These findings make the Krylov model order reduction method very suitable for the above mentioned subsea applications.
Abstract: In this paper, a two factor scheme is proposed to
generate cryptographic keys directly from biometric data, which
unlike passwords, are strongly bound to the user. Hash value of the
reference iris code is used as a cryptographic key and its length
depends only on the hash function, being independent of any other
parameter. The entropy of such keys is 94 bits, which is much higher
than any other comparable system. The most important and distinct
feature of this scheme is that it regenerates the reference iris code by
providing a genuine iris sample and the correct user password. Since
iris codes obtained from two images of the same eye are not exactly
the same, error correcting codes (Hadamard code and Reed-Solomon
code) are used to deal with the variability. The scheme proposed here
can be used to provide keys for a cryptographic system and/or for
user authentication. The performance of this system is evaluated on
two publicly available databases for iris biometrics namely CBS and
ICE databases. The operating point of the system (values of False
Acceptance Rate (FAR) and False Rejection Rate (FRR)) can be set
by properly selecting the error correction capacity (ts) of the Reed-
Solomon codes, e.g., on the ICE database, at ts = 15, FAR is 0.096%
and FRR is 0.76%.
Abstract: Most, if not all, public hospitals in Thailand have encountered a common problem regarding the increasing demand for medical services. The increasing number of patients causes so much strain on the hospital-s services, over-crowded, overloaded working hours, staff fatigue, medical error and long waiting time. This research studied the characteristics of operational processes of the medical care services at the medicine department in a large public university hospital. The research focuses on details regarding methods, procedures, processes, resources, and time management in overall processes. The simulation model is used as a tool to analyze the impact of various improvement strategies.