Abstract: Aerospace vehicles are subjected to non-uniform
thermal loading that may cause thermal buckling. A study was
conducted on the thermal post-buckling of shape memory alloy
composite plates subjected to the non-uniform tent-like temperature
field. The shape memory alloy wires were embedded within the
laminated composite plates to add recovery stress to the plates. The
non-linear finite element model that considered the recovery stress of
the shape memory alloy and temperature dependent properties of the
shape memory alloy and composite matrix along with its source
codes were developed. It was found that the post-buckling paths of
the shape memory alloy composite plates subjected to various tentlike
temperature fields were stable within the studied temperature
range. The addition of shape memory alloy wires to the composite
plates was found to significantly improve the post-buckling behavior
of laminated composite plates under non-uniform temperature
distribution.
Abstract: The complex shape of the human pelvic bone was
successfully imaged and modeled using finite element FE processing.
The bone was subjected to quasi-static and dynamic loading
conditions simulating the effect of both weight gain and impact.
Loads varying between 500 – 2500 N (~50 – 250 Kg of weight) was
used to simulate 3D quasi-static weight gain. Two different 3D
dynamic analyses, body free fall at two different heights (1 and 2 m)
and forced side impact at two different velocities (20 and 40 Km/hr)
were also studied. The computed resulted stresses were compared for
the four loading cases, where Von Misses stresses increases linearly
with the weight gain increase under quasi-static loading. For the
dynamic models, the Von Misses stress history behaviors were
studied for the affected area and effected load with respect to time.
The normalization Von Misses stresses with respect to the applied
load were used for comparing the free fall and the forced impact load
results. It was found that under the forced impact loading condition
an over lapping behavior was noticed, where as for the free fall the
normalized Von Misses stresses behavior was found to nonlinearly
different. This phenomenon was explained through the energy
dissipation concept. This study will help designers in different
specialization in defining the weakest spots for designing different
supporting systems.
Abstract: Mobile agents are a powerful approach to develop distributed systems since they migrate to hosts on which they have the resources to execute individual tasks. In a dynamic environment like a peer-to-peer network, Agents have to be generated frequently and dispatched to the network. Thus they will certainly consume a certain amount of bandwidth of each link in the network if there are too many agents migration through one or several links at the same time, they will introduce too much transferring overhead to the links eventually, these links will be busy and indirectly block the network traffic, therefore, there is a need of developing routing algorithms that consider about traffic load. In this paper we seek to create cooperation between a probabilistic manner according to the quality measure of the network traffic situation and the agent's migration decision making to the next hop based on decision tree learning algorithms.
Abstract: Nonlinear and unbalance loads in three phase
networks create harmonics and losses. Active and passive filters are
used for elimination or reduction of these effects. Passive filters have
some limitations. For example, they are designed only for a specific
frequency and they may cause to resonance in the network at the
point of common coupling. The other drawback of a passive filter is
that the sizes of required elements are normally large. The active
filter can improve some of limitations of passive filter for example;
they can eliminate more than one harmonic and don't cause resonance
in the network. In this paper inverter analysis have been done
simultaneously in three phase and the RL impedance of the line have
been considered. A sliding mode control based on energy feedback of
capacitors is employed in the design with this method, the dynamic
speed of the filter is improved effectively and harmonics and load
unbalance is compensating quickly.
Abstract: Chatter vibration has been a troublesome problem
for a machine tool toward the high precision and high speed machining.
Essentially, the machining performance is determined by the dynamic
characteristics of the machine tool structure and dynamics of cutting
process, which can further be identified in terms of the stability lobe
diagram. Therefore, realization on the machine tool dynamic behavior
can help to enhance the cutting stability. To assess the dynamic
characteristics and machining stability of a vertical milling system
under the influence of a linear guide, this study developed a finite
element model integrated the modeling of linear components with the
implementation of contact stiffness at the rolling interface. Both the
finite element simulations and experimental measurements reveal that
the linear guide with different preload greatly affects the vibration
behavior and milling stability of the vertical column spindle head
system, which also clearly indicate that the predictions of the
machining stability agree well with the cutting tests. It is believed that
the proposed model can be successfully applied to evaluate the
dynamics performance of machine tool systems of various
configurations.
Abstract: Lateral-torsional buckling (LTB) is one of the
phenomenae controlling the ultimate bending strength of steel Ibeams
carrying distributed loads on top flange. Built-up I-sections
are used as main beams and distributors. This study investigates the
ultimate bending strength of such beams with sections of different
classes including slender elements. The nominal strengths of the
selected beams are calculated for different unsupported lengths
according to the Provisions of the American Institute of Steel
Constructions (AISC-LRFD). These calculations are compared with
results of a nonlinear inelastic study using accurate FE model for this
type of loading. The goal is to investigate the performance of the
provisions for the selected sections. Continuous distributed load at
the top flange of the beams was applied at the FE model.
Imperfections of different values are implemented to the FE model to
examine their effect on the LTB of beams at failure, and hence, their
effect on the ultimate strength of beams. The study also introduces a
procedure for evaluating the performance of the provisions compared
with the accurate FEA results of the selected sections. A simplified
design procedure is given and recommendations for future code
updates are made.
Abstract: Overloading is a technique to accommodate more
number of users than the spreading factor N. This is a bandwidth
efficient scheme to increase the number users in a fixed bandwidth.
One of the efficient schemes to overload a CDMA system is to use
two sets of orthogonal signal waveforms (O/O). The first set is
assigned to the N users and the second set is assigned to the
additional M users. An iterative interference cancellation technique is
used to cancel interference between the two sets of users. In this
paper, the performance of an overloading scheme in which the first N
users are assigned Walsh-Hadamard orthogonal codes and extra users
are assigned the same WH codes but overlaid by a fixed (quasi) bent
sequence [11] is evaluated. This particular scheme is called Quasi-
Orthogonal Sequence (QOS) O/O scheme, which is a part of
cdma2000 standard [12] to provide overloading in the downlink
using single user detector. QOS scheme are balance O/O scheme,
where the correlation between any set-1 and set-2 users are
equalized. The allowable overload of this scheme is investigated in
the uplink on an AWGN and Rayleigh fading channels, so that the
uncoded performance with iterative multistage interference
cancellation detector remains close to the single user bound. It is
shown that this scheme provides 19% and 11% overloading with
SDIC technique for N= 16 and 64 respectively, with an SNR
degradation of less than 0.35 dB as compared to single user bound at
a BER of 0.00001. But on a Rayleigh fading channel, the channel
overloading is 45% (29 extra users) at a BER of 0.0005, with an SNR
degradation of about 1 dB as compared to single user performance
for N=64. This is a significant amount of channel overloading on a
Rayleigh fading channel.
Abstract: Aims for this study: first, to compare the expertise
level in data analysis, communication and information technologies
in undergraduate psychology students. Second, to verify the factor
structure of E-ETICA (Escala de Experticia en Tecnologias de la Informacion, la Comunicacion y el Análisis or Data Analysis,
Communication and Information'Expertise Scale) which had shown
an excellent internal consistency (α= 0.92) as well as a simple factor
structure. Three factors, Complex, Basic Information and
Communications Technologies and E-Searching and Download
Abilities, explains 63% of variance. In the present study, 260
students (119 juniors and 141 seniors) were asked to respond to
ETICA (16 items Likert scale of five points 1: null domain to 5: total
domain). The results show that both junior and senior students report
having very similar expertise level; however, E-ETICA presents a
different factor structure for juniors and four factors explained also
63% of variance: Information E-Searching, Download and Process;
Data analysis; Organization; and Communication technologies.
Abstract: In This paper, the behavior of eccentric braced frame
(EBF) is studied with replacing friction damper (FD) in confluence of these braces, in 5 and 10-storey steel frames. For FD system, the main step is to determine the slip load. For this reason, the performance indexes include roof displacement, base shear, dissipated energy and relative performance should be investigated. In
nonlinear dynamic analysis, the response of structure to three
earthquake records has been obtained and the values of roof
displacement, base shear and column axial force for FD and EBF
frames have been compared. The results demonstrate that use of the FD in frames, in comparison with the EBF, substantially reduces the roof displacement, column axial force and base shear. The obtained results show suitable performance of FD in higher storey structure in
comparison with the EBF.
Abstract: This paper focuses on systematic analysis and
controller design of the two-inertia STABILIZATION system,
considering the angular motion on a base body. This approach is
essential to the stabilization system to aim at a target under three or six
degrees of freedom base motion. Four controllers, such as
conventional PDF(Pseudo-Derivative Feedback) controller with
motor speed feedback, PDF controller with load speed feedback,
modified PDF controller with motor-load speed feedback and
feedforward controller added to modified PDF controller, are
suggested to improve reference tracking and disturbance rejection
performance. Characteristics and performance of each controller are
analyzed and validated by simulation in the case of the modified PDF
controller with and without a feedforward controller.
Abstract: In the past, there were many bridge-s collapses due to
lack of bridge structural capacity information. Most of concrete
bridge health was relied on information from visual inspection, which
sometime was inadequate. This study was conducted in order to
investigate relationship between bridge structural condition and
bridge visual condition. This study was a part of a big project
conducted at Department of Highways of Thailand. In this study, 31
bridges including slab-type bridges, plank-girder bridges, prestressed
box-beam bridges, prestressed I-girder bridges and prestressed multibeam
bridges were selected for visual inspection and load test. It was
found a positive correlation between bridge appearance and bridge-s
load carrying capacity. However, statistical characteristic revealed
low correlation between them.
Abstract: Server provisioning is one of the most attractive topics in virtualization systems. Virtualization is a method of running multiple independent virtual operating systems on a single physical computer. It is a way of maximizing physical resources to maximize the investment in hardware. Additionally, it can help to consolidate servers, improve hardware utilization and reduce the consumption of power and physical space in the data center. However, management of heterogeneous workloads, especially for resource utilization of the server, or so called provisioning becomes a challenge. In this paper, a new concept for managing workloads based on user behavior is presented. The experimental results show that user behaviors are different in each type of service workload and time. Understanding user behaviors may improve the efficiency of management in provisioning concept. This preliminary study may be an approach to improve management of data centers running heterogeneous workloads for provisioning in virtualization system.
Abstract: This paper presents a novel three-phase utility
frequency to high frequency soft switching power conversion circuit
with dual mode pulse width modulation and pulse density modulation
for high power induction heating applications as melting of steel and
non ferrous metals, annealing of metals, surface hardening of steel
and cast iron work pieces and hot water producers, steamers and
super heated steamers. This high frequency power conversion circuit
can operate from three-phase systems to produce high current for
high power induction heating applications under the principles of
ZVS and it can regulate its ac output power from the rated value to a
low power level. A dual mode modulation control scheme based on
high frequency PWM in synchronization with the utility frequency
positive and negative half cycles for the proposed high frequency
conversion circuit and utility frequency pulse density modulation is
produced to extend its soft switching operating range for wide ac
output power regulation. A dual packs heat exchanger assembly is
designed to be used in consumer and industrial fluid pipeline systems
and it is proved to be suitable for the hot water, steam and super
heated steam producers. Experiment and simulation results are given
in this paper to verify the operation principles of the proposed ac
conversion circuit and to evaluate its power regulation and
conversion efficiency. Also, the paper presents a mutual coupling
model of the induction heating load instead of equivalent transformer
circuit model.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: A simple network model is developed in OPNET to
study the performance of the Wi-Fi protocol. The model is simulated
in OPNET and performance factors such as load, throughput and delay
are analysed from the model. Four applications such as oracle, http, ftp
and voice are applied over the Wireless LAN network to determine the
throughput. The voice application utilises a considerable amount of
bandwidth of up to 5Mbps, as a result the 802.11g standard of the
Wi-Fi protocol was chosen which can support a data rate of up to
54Mbps. Results indicate that when the load in the Wi-Fi network is
increased the queuing delay on the point-to-point links in the Wi-Fi
network significantly reduces until it is comparable to that of WiMAX.
In conclusion, the queuing delay of the Wi-Fi protocol for the network
model simulated was about 0.00001secs comparable to WiMAX
network values.
Abstract: Currently, a large number of license activities (Early
Site Permits, Combined Operating License, reactor certifications,
etc.), are pending for review before the United States Nuclear
Regulatory Commission (US NRC). Much of the senior staff at the
NRC is now committed to these review and licensing actions. To
address this additional workload, the NRC has recruited a large
number of new Regulatory Staff for dealing with these and other
regulatory actions such as the US Fleet of Research and Test Reactors
(RTRs). These reactors pose unusual demands on Regulatory Staff
since the US Fleet of RTRs, although few (32 Licensed RTRs as of
2010), they represent a broad range of reactor types, operations, and
research and training aspects that nuclear reactor power plants (such
as the 104 LWRs) do not pose. The NRC must inspect and regulate
all these facilities. This paper addresses selected training topics and
regulatory activities providedNRC Inspectors for RTRs.
Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: Currently, most of distance learning courses can only
deliver standard material to students. Students receive course content
passively which leads to the neglect of the goal of education – “to suit
the teaching to the ability of students". Providing appropriate course
content according to students- ability is the main goal of this paper.
Except offering a series of conventional learning services, abundant
information available, and instant message delivery, a complete online
learning environment should be able to distinguish between students-
ability and provide learning courses that best suit their ability.
However, if a distance learning site contains well-designed course
content and design but fails to provide adaptive courses, students will
gradually loss their interests and confidence in learning and result in
ineffective learning or discontinued learning. In this paper, an
intelligent tutoring system is proposed and it consists of several
modules working cooperatively in order to build an adaptive learning
environment for distance education. The operation of the system is
based on the result of Self-Organizing Map (SOM) to divide students
into different groups according to their learning ability and learning
interests and then provide them with suitable course content.
Accordingly, the problem of information overload and internet traffic
problem can be solved because the amount of traffic accessing the
same content is reduced.
Abstract: This study focuses on emission of black carbon (BC)
from field open burning of corn residues. Real-time BC
concentration was measured by Micro Aethalometer from field
burning and simulated open burning in a chamber (SOC)
experiments. The average concentration of BC was 1.18±0.47 mg/m3
in the field and 0.89±0.63 mg/m3 in the SOC. The deduced emission
factor from field experiments was 0.50±0.20 gBC/kgdm, and 0.56±0.33
gBC/kgdm from SOC experiment, which are in good agreement with
other studies. In 2007, the total burned area of corn crop was 8,000
ha, resulting in an emission load of BC 20 ton corresponding to 44.5
million kg CO2 equivalent. Therefore, the control of open burning in
corn field represents a significant global warming reduction option.