Abstract: The important issue considered in the widespread deployment of Wireless Sensor Networks (WSNs) is an efficiency of the energy consumption. In this paper, we present a study of the optimal relay station planning problems using Binary Integer Linear Programming (BILP) model to minimize the energy consumption in WSNs. Our key contribution is that the proposed model not only ensures the required network lifetime but also guarantees the radio connectivity at high level of communication quality. Specially, we take into account effects of noise, signal quality limitation and bit error rate characteristics. Numerical experiments were conducted in various network scenarios. We analyzed the effects of different sensor node densities and distribution on the energy consumption.
Abstract: The RANS method with Saffman-s turbulence model
was employed to solve the time-dependent turbulent Navier-Stokes
and energy equations for oscillating pipe flows. The method of
partial sums of the Fourier series is used to analyze the harmonic
velocity and temperature results. The complete structures of the
oscillating pipe flows and the averaged Nusselt numbers on the tube
wall are provided by numerical simulation over wide ranges of ReA
and ReR. Present numerical code is validated by comparing the
laminar flow results to analytic solutions and turbulence flow results
to published experimental data at lower and higher Reynolds
numbers respectively. The effects of ReA and ReR on the velocity,
temperature and Nusselt number distributions have been di scussed.
The enhancement of the heat transfer due to oscillating flows has
also been presented. By the way of analyzing the overall Nusselt
number over wide ranges of the Reynolds number Re and Keulegan-
Carpenter number KC, the optimal ratio of the tube diameter over
the oscillation amplitude is obtained based on the existence of a
nearly constant optimal KC number. The potential application of the
present results in sea water cooling has also been discussed.
Abstract: Spray chilling using air-mist nozzles has received
much attention in the food processing industry because of the
benefits it has shown over forced air convection. These benefits
include an increase in the heat transfer coefficient and a reduction in
the water loss by the product during cooling. However, few studies
have simulated the heat transfer and aerodynamics phenomena of the
air-mist chilling process for optimal operating conditions. The study
provides insight into the optimal conditions for spray impaction, heat
transfer efficiency and control of surface flooding. A computational
fluid dynamics model using a two-phase flow composed of water
droplets injected with air is developed to simulate the air-mist
chilling of food products. The model takes into consideration
droplet-to-surface interaction, water-film accumulation and surface
runoff. The results of this study lead to a better understanding of the
heat transfer enhancement, water conservation, and to a clear
direction for the optimal design of air-mist chilling systems that can
be used in commercial applications in the food and meat processing
industries.
Abstract: All climate models agree that the temperature in
Greece will increase in the range of 1° to 2°C by the year 2030 and
mean sea level in Mediterranean is expected to rise at the rate of 5
cm/decade. The aim of the present paper is the estimation of the
coastline displacement driven by the climate change and sea level
rise. In order to achieve that, all known statistical and non-statistical
computational methods are employed on some Greek coastal areas.
Furthermore, Kalman filtering techniques are for the first time
introduced, formulated and tested. Based on all the above, shoreline
change signals and noises are computed and an inter-comparison
between the different methods can be deduced to help evaluating
which method is most promising as far as the retrieve of shoreline
change rate is concerned.
Abstract: Conceptualization strengthens intelligent systems in generalization skill, effective knowledge representation, real-time inference, and managing uncertain and indefinite situations in addition to facilitating knowledge communication for learning agents situated in real world. Concept learning introduces a way of abstraction by which the continuous state is formed as entities called concepts which are connected to the action space and thus, they illustrate somehow the complex action space. Of computational concept learning approaches, action-based conceptualization is favored because of its simplicity and mirror neuron foundations in neuroscience. In this paper, a new biologically inspired concept learning approach based on the probabilistic framework is proposed. This approach exploits and extends the mirror neuron-s role in conceptualization for a reinforcement learning agent in nondeterministic environments. In the proposed method, instead of building a huge numerical knowledge, the concepts are learnt gradually from rewards through interaction with the environment. Moreover the probabilistic formation of the concepts is employed to deal with uncertain and dynamic nature of real problems in addition to the ability of generalization. These characteristics as a whole distinguish the proposed learning algorithm from both a pure classification algorithm and typical reinforcement learning. Simulation results show advantages of the proposed framework in terms of convergence speed as well as generalization and asymptotic behavior because of utilizing both success and failures attempts through received rewards. Experimental results, on the other hand, show the applicability and effectiveness of the proposed method in continuous and noisy environments for a real robotic task such as maze as well as the benefits of implementing an incremental learning scenario in artificial agents.
Abstract: This paper represents the results of long term strength of mortar incorporating Rice Husk Ash (RHA). For these work mortar samples were made according to ASTM standard C 109/C. OPC cement was partially replaced by RHA at 0, 10, 15, 20, 25 and 30 percent replacement level. After casting all samples were kept in controlled environment and curing was done up to 90 days. Test of mortar was performed on 3, 7, 28, 90, 365 and 700 days. It is noticed that OPC mortar shows better strength at early age than mortar having RHA but at 90 days and onward the picture is different. At 700 days it is observed that mortar containing 20% RHA shows better result than any other samples.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.
Abstract: This paper proposes a vertical beamforming concept
to a cellular network employing Fractional Frequency Reuse
technique including with cell sectorization. Two different beams are
utilized in cell-center and cell-edge, separately. The proposed concept
is validated through computer simulation in term of SINR and
channel capacity. Also, comparison when utilizing horizontal and
vertical beam formation is in focus. The obtained results indicate
that the proposed concept can improve the performance of the
cellular networks comparing with the one using horizontal
beamforming.
Abstract: Plant growth is affected by the osmotic stress as well as toxicity of salt in leaves. In order to study of salt stress effects on stomatal conductance and growth rate and relationship between them as wells osmotic and Na+-specific effects on these traits, four bread wheat genotypes differing in salt tolerance were selected. Salinity was applied when the leaf 4 was fully expanded. Sodium (Na+) concentrations in flag leaf blade at 3 salinity levels (0, 100 and 200 mM NaCl) were measured. Salt-tolerant genotypes showed higher stomatal conductance and growth rate compared to salt-sensitive ones. After 10 and 20 days exposure to salt, stomatal conductance and relative growth rate were reduced, but the reduction was greater in sensitive genotypes. Growth rate was reduced severely in the first period (1-10 days) of salt commencements and it was due to osmotic effect of salt not Na+ toxicity. In the second period (11-20 days) after salt treatment growth reduced only when salt accumulated to toxic concentrations in the leaves. A positive relationship between stomatal conductance and relative growth rate showed that stomatal conductance can be a reliable indicator of growth rate, and finally can be considered as a sensitive indicator of the osmotic stress. It seems 20 days after salinity, the major effect of salt, especially at low to moderate salinity levels on growth properties was due to the osmotic effect of salt, not to Na+-specific effects within the plant.
Abstract: Adaptive echo cancellers with two-path algorithm are
applied to avoid the false adaptation during the double-talk situation.
In the two-path algorithm, several transfer logic solutions have been
proposed to control the filter update. This paper presents an improved
transfer logic solution. It improves the convergence speed of the
two-path algorithm, and allows the reduction of the memory elements
and computational complexity. Results of simulations show the
improved performance of the proposed solution.
Abstract: The research is to minimize environmental damage
pertinent to maritime activities about the operation of lighter boat
anchorage and its tugboat. The guidance on upgrading current
harbor service and infrastructure has been provided to Kho Sichang
Municpality. This will involve a study of the maritime logistics of
the water area under jurisdiction of the Sichang island Municipality
and possible recommendations may involve charging taxes,
regulations and fees. With implementing these recommendations will
help in protection of the marine environment and in increasing
operator functionality. Additionally, our recommendation is to
generate a consistent revenue stream to the municipality. The action
items contained in this research are feasible and effective, the success
of these initiatives are heavily dependent upon successful promotion
and enforcement. Promoting new rules and regulations effectively
and peacefully can be done through theories and techniques used in
the psychology of persuasion. In order to assure compliance with the
regulations, the municipality must maintain stringent patrols and
fines for violators. In order to become success, the Municipality
must preserve a consistent, transparent and significant enforcement
system. Considering potential opportunities outside of the current
state of the municipality, the authors recommend that Koh Sichang be
given additional jurisdiction to capture value from the master vessels,
as well as to confront the more significant environmental challenges
these vessels pose. Finally, the authors recommend that the Port of
Koh Sichang Island obtain a free port status in order to increase
economic viability and overall sustainability.
Abstract: The various applications of VLSI circuits in highperformance
computing, telecommunications, and consumer
electronics has been expanding progressively, and at a very hasty
pace. This paper describes a new model for partitioning a circuit
using DBSCAN and fuzzy ARTMAP neural network. The first step
is concerned with feature extraction, where we had make use
DBSCAN algorithm. The second step is the classification and is
composed of a fuzzy ARTMAP neural network. The performance of
both approaches is compared using benchmark data provided by
MCNC standard cell placement benchmark netlists. Analysis of the
investigational results proved that the fuzzy ARTMAP with
DBSCAN model achieves greater performance then only fuzzy
ARTMAP in recognizing sub-circuits with lowest amount of
interconnections between them The recognition rate using fuzzy
ARTMAP with DBSCAN is 97.7% compared to only fuzzy
ARTMAP.
Abstract: The issue of real-time and reliable report delivery is extremely important for taking effective decision in a real world mission critical Wireless Sensor Network (WSN) based application. The sensor data behaves differently in many ways from the data in traditional databases. WSNs need a mechanism to register, process queries, and disseminate data. In this paper we propose an architectural framework for data placement and management. We propose a reliable and real time approach for data placement and achieving data integrity using self organized sensor clusters. Instead of storing information in individual cluster heads as suggested in some protocols, in our architecture we suggest storing of information of all clusters within a cell in the corresponding base station. For data dissemination and action in the wireless sensor network we propose to use Action and Relay Stations (ARS). To reduce average energy dissipation of sensor nodes, the data is sent to the nearest ARS rather than base station. We have designed our architecture in such a way so as to achieve greater energy savings, enhanced availability and reliability.
Abstract: A fundamental model consisting of charged particles
moving in free space exposed to alternating and direct current (ACDC)
electromagnetic fields is analyzed. Effects of charged particles
initial position and initial velocity to cyclotron resonance frequency
are observed. Strong effects are observed revealing that effects of
electric and magnetic fields on a charged particle in free space
varies with the initial conditions. This indicates the frequency where
maximum displacement occur can be changed. At this frequency
the amplitude of oscillation of the particle displacement becomes
unbounded.
Abstract: This paper presents a new and efficient approach for capacitor placement in radial distribution systems that determine the optimal locations and size of capacitor with an objective of improving the voltage profile and reduction of power loss. The solution methodology has two parts: in part one the loss sensitivity factors are used to select the candidate locations for the capacitor placement and in part two a new algorithm that employs Plant growth Simulation Algorithm (PGSA) is used to estimate the optimal size of capacitors at the optimal buses determined in part one. The main advantage of the proposed method is that it does not require any external control parameters. The other advantage is that it handles the objective function and the constraints separately, avoiding the trouble to determine the barrier factors. The proposed method is applied to 9, 34, and 85-bus radial distribution systems. The solutions obtained by the proposed method are compared with other methods. The proposed method has outperformed the other methods in terms of the quality of solution.
Abstract: The seismic response of steel shear wall system considering nonlinearity effects using finite element method is investigated in this paper. The non-linear finite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of finite element code. A numerical model based on the finite element method for the seismic analysis of shear wall is presented with developing of finite element code in this research. To develop the finite element code, the standard Galerkin weighted residual formulation is used. Two-dimensional plane stress model and total Lagrangian formulation was carried out to present the shear wall response and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The presented model in this paper can be developed for analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: Studies have shown that the SnAgCu solder family has been widely used as a replacement for conventional Sn-Pb solders. An attractive approach is by introducing alloying additives (rare earth elements (RE), Zn, Co, Fe, Ni, Sb) into the SnAgCu solder, which helps in refining the microstructure also improving the mechanical and wetting properties of the solder. The present work focuses on the effect of additions of 0.5% Ce and Fe into Sn-3.0Ag-0.5Cu solder, in attempt to reduce the intermetallic compound (IMC) growth and reflow properties of the solder on Cu and Ni (P) surface finish, as well as effects thermal aging on the formation of intermetallic compound (IMC) on different surface finish. Excessive intermetallic compound growth may effect the interface and solder joint due to the brittle nature of the intermetallic compounds. Thus, by introducing alloying elements, IMC layer thickness can be decrease, resulting in better joint and solder reliability.
Abstract: An investigation of noise in a micro stepping motor is
considered to study in this article. Because of the trend towards higher
precision and more and more small 3C (including Computer,
Communication and Consumer Electronics) products, the micro
stepping motor is frequently used to drive the micro system or the
other 3C products. Unfortunately, noise in a micro stepped motor is
too large to accept by the customs. To depress the noise of a micro
stepped motor, the dynamic characteristics in this system must be
studied. In this article, a Visual Basic (VB) computer program speed
controlled micro stepped motor in a digital camera is investigated.
Karman KD2300-2S non-contract eddy current displacement sensor,
probe microphone, and HP 35670A analyzer are employed to analyze
the dynamic characteristics of vibration and noise in a motor. The
vibration and noise measurement of different type of bearings and
different treatment of coils are compared. The rotating components,
bearings, coil, etc. of the motor play the important roles in producing
vibration and noise. It is found that the noise will be depressed about
3~4 dB and 6~7 dB, when substitutes the copper bearing with plastic
one and coats the motor coil with paraffin wax, respectively.
Abstract: Ten simply supported grossly underreinforced
tapered concrete beams of full size were tested upto complete
collapse under flexural effect .Out of 10 beams, 5 beams were
nonfibrous and the remaining beams contained fibres. The beams
had a variation in the tapered angle as 2°, 4°, 6°, 8° and 10°. The
concrete mix, conventional steel and the type of fibre used were
held constant. Flat corrugated steel fibres were utilized as
secondary reinforcement. The strength and stability parameters
were measured. It is established that the fibrous tapered beams can
be used economically in earthquake prone areas.
Abstract: Most of the losses in a power system relate to
the distribution sector which always has been considered.
From the important factors which contribute to increase losses
in the distribution system is the existence of radioactive flows.
The most common way to compensate the radioactive power
in the system is the power to use parallel capacitors. In
addition to reducing the losses, the advantages of capacitor
placement are the reduction of the losses in the release peak of
network capacity and improving the voltage profile. The point
which should be considered in capacitor placement is the
optimal placement and specification of the amount of the
capacitor in order to maximize the advantages of capacitor
placement.
In this paper, a new technique has been offered for the
placement and the specification of the amount of the constant
capacitors in the radius distribution network on the basis of
Genetic Algorithm (GA). The existing optimal methods for
capacitor placement are mostly including those which reduce
the losses and voltage profile simultaneously. But the
retaliation cost and load changes have not been considered as
influential UN the target function .In this article, a holistic
approach has been considered for the optimal response to this
problem which includes all the parameters in the distribution
network: The price of the phase voltage and load changes. So,
a vast inquiry is required for all the possible responses. So, in
this article, we use Genetic Algorithm (GA) as the most
powerful method for optimal inquiry.