Abstract: Field experiment was conducted to investigate the combine use of animal manure and inorganic fertilizer on growth and yield performance of vegetable cowpea. The experiment was laid out in a Randomized Complete Block Design (RCBD) with seven treatments. Poultry manure, cattle manure and goat manure were evaluated with recommended level of inorganic fertilizer for vegetable cowpea. The highest crop yield was obtained by the application of poultry manure combined with the recommended level of inorganic fertilizer. The lowest yield was obtained by the application of goat manure only. In addition, the results revealed that the goat manure and cattle manure were inferior to poultry manure as a source of organic manure for vegetable cowpea cultivation. The animal manure combine with chemical fertilizer gave a higher yield when compared to the sole application of animal manure. The soil analysis showed that the nitrogen content and phosphorus content of poultry manure treated plots were higher than other treatments tested. But potassium content was higher in goat manure treated plots. The results further revealed that the poultry manure has a beneficial effect on crop growth and yield compared with other treatments. Therefore, the combined use of poultry manure with inorganic fertilizer application has been recognized as the most suitable way of ensuring high crop yield.
Abstract: Self-sensing estimates the air gap within an electro
magnetic path by analyzing the bearing coil current and/or voltage
waveform. The self-sensing concept presented in this paper has been
developed within the research project “Active Magnetic Bearings
with Supreme Reliability" and is used for position sensor fault
detection.
Within this new concept gap calculation is carried out by an alldigital
analysis of the digitized coil current and voltage waveform.
For analysis those time periods within the PWM period are used,
which give the best results. Additionally, the concept allows the
digital compensation of nonlinearities, for example magnetic
saturation, without degrading signal quality. This increases the
accuracy and robustness of the air gap estimation and additionally
reduces phase delays.
Beneath an overview about the developed concept first
measurement results are presented which show the potential of this
all-digital self-sensing concept.
Abstract: This paper develops a critical perspective on using
culture and creativity as tools for urban regeneration. Following a
brief assessment of the evolution of cultural policy in recent decades
and different urban regeneration scheme, the concepts of creativity
and creative cities are discussed. This is followed by an attempt to
clarify the relationship between the concepts of creativity and culture.
A more detailed critique of cultural and creative initiatives in Serbian
cities is then undertaken. These attempts show that the potential for
development of urban regeneration driven by culture and creativity
exist. But, these initiatives failed to produce adequate results because
they did not take root as a comprehensive urban regeneration
strategy, therefore, recommendations for further development are
offered.
Abstract: Complex statistical analysis of stresses in concrete
slab of the real type of rigid pavement is performed. The
computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method
that respects the structural nonlinearity, enables to model different arrangement of joints, and the entire model can be loaded by the
thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with help of special
contact elements. Four concrete slabs separated by transverse and
longitudinal joints and the additional subgrade layers and soil to the depth of about 3m are modeled. The thickness of individual layers,
physical and mechanical properties of materials, characteristics of
joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique
Updated Latin Hypercube Sampling with 20 simulations is used for statistical analysis. As results, the estimates of basic statistics of the
principal stresses s1 and s3 in 53 points on the upper and lower surface of the slabs are obtained.
Abstract: Mixed Model Production is the practice of assembling
several distinct and different models of a product on the same
assembly line without changeovers and then sequencing those models
in a way that smoothes the demand for upstream components. In this
paper, we consider an objective function which minimizes total
stoppage time and total idle time and it is presented sequence
dependent set up time. Many studies have been done on the mixed
model assembly lines. But in this paper we specifically focused on
reducing the idle times. This is possible through various help policies.
For improving the solutions, some cases developed and about 40 tests
problem was considered. We use scatter search for optimization and
for showing the efficiency of our algorithm, experimental results
shows behavior of method. Scatter search and help policies can
produce high quality answers, so it has been used in this paper.
Abstract: Realistic 3D face model is desired in various
applications such as face recognition, games, avatars, animations, and
etc. Construction of 3D face model is composed of 1) building a face
shape model and 2) rendering the face shape model. Thus, building a
realistic 3D face shape model is an essential step for realistic 3D face
model. Recently, 3D morphable model is successfully introduced to
deal with the various human face shapes. 3D dense correspondence
problem should be precedently resolved for constructing a realistic 3D
dense morphable face shape model. Several approaches to 3D dense
correspondence problem in 3D face modeling have been proposed
previously, and among them optical flow based algorithms and TPS
(Thin Plate Spline) based algorithms are representative. Optical flow
based algorithms require texture information of faces, which is
sensitive to variation of illumination. In TPS based algorithms
proposed so far, TPS process is performed on the 2D projection
representation in cylindrical coordinates of the 3D face data, not
directly on the 3D face data and thus errors due to distortion in data
during 2D TPS process may be inevitable.
In this paper, we propose a new 3D dense correspondence algorithm
for 3D dense morphable face shape modeling. The proposed algorithm
does not need texture information and applies TPS directly on 3D face
data. Through construction procedures, it is observed that the proposed
algorithm constructs realistic 3D face morphable model reliably and
fast.
Abstract: The aim of this paper is to identify the most suitable
model for churn prediction based on three different techniques. The
paper identifies the variables that affect churn in reverence of
customer complaints data and provides a comparative analysis of
neural networks, regression trees and regression in their capabilities
of predicting customer churn.
Abstract: Knowledge management is a critical component of
competitive success in service organizations. Knowledge
management centers on creating new knowledge and utilizing
existing knowledge. While utilizing existing knowledge relates to
input and control and can lead to a reduction in costs; creating new
knowledge relates to output and growth and can lead to an increase in
revenue. Therefore managers must ensure that they can successfully
optimize the knowledge and talent in their organizations. To do this
they and must try to develop an environment that promotes the
generation, acquisition, transfer and use of valuable knowledge in
creative ways. However knowledge management is complex and
diverse. Research suggests that organizations in general and SMEs in
particular are finding it difficult to implement successful knowledge
management initiatives. Our research attempts to understand whether
organizations are adopting best practice initiatives in their
organizations. This paper presents findings from an exploratory study
of 139 SMEs operating in the tourism sector across Europe. The
goals of the survey is to assess the level of awareness of knowledge
and talent management strategies and methodologies and to
determine whether the responding companies implement best practice
knowledge management initiatives in their organizations Analysis of
the findings from the study are presented and discussed.
Abstract: In this research, the laminar heat transfer of natural convection on vertical surfaces has been investigated. Most of the studies on natural convection have been considered constantly whereas velocity and temperature domain, do not change with time, transient one are used a lot. Governing equations are solved using a finite volume approach. The convective terms are discretized using the power-law scheme, whereas for diffusive terms the central difference is employed. Coupling between the velocity and pressure is made with SIMPLE algorithm. The resultant system of discretized linear algebraic equations is solved with an alternating direction implicit scheme. Then a configuration of rectangular fins is put in different ways on the surface and heat transfer of natural convection on these surfaces without sliding is studied and finally optimization is done.
Abstract: A multi-block algorithm and its implementation in two-dimensional finite element numerical model CCHE2D are presented. In addition to a conventional Lagrangian Interpolation Method (LIM), a novel interpolation method, called Consistent Interpolation Method (CIM), is proposed for more accurate information transfer across the interfaces. The consistent interpolation solves the governing equations over the auxiliary elements constructed around the interpolation nodes using the same numerical scheme used for the internal computational nodes. With the CIM, the momentum conservation can be maintained as well as the mass conservation. An imbalance correction scheme is used to enforce the conservation laws (mass and momentum) across the interfaces. Comparisons of the LIM and the CIM are made using several flow simulation examples. It is shown that the proposed CIM is physically more accurate and produces satisfactory results efficiently.
Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: Composite steel shear wall is a lateral load resisting system which consists of a steel plate with concrete wall attached to one or both sides to prevent it from elastic buckling. The composite behavior is ensured by utilizing high-strength bolts. This paper investigates the effect of distance between bolts, and for this purpose 14 one-story one-bay specimens with various bolts spacing were modeled by finite element code which is developed by the authors. To verify the model, numerical results were compared with a valid experiment which illustrate proper agreement. Results depict increasing the distance between bolts would improve the seismic ever, this increase must be limited, because of large distances will cause widespread buckling of the steel plate in free subpanels between bolts and would result in no improvement. By comparing the results in elastic region, it was observed initial stiffness is not affected by changing the distance.
Abstract: According to historical legend, after the revelation of the holy Qur'an, which gave the hijab compulsory and women were required to cover the head and body with a handkerchief, and the general form of clothing in her veil, Muslim women have begun to comply with this worthy tradition. This article discusses the history of the rise and spread of the hijab and its types. And here is described in detail types of hijab and its intended value, style hijab in different regions. Now wearing the hijab, hijab in general the problem is important not only in the Arab world, but also in the world.
Abstract: This paper presents a comparative study on
Vanadyl Phthalocyanine (VOPc) thin films deposited by thermal
evaporation and spin coating techniques. The samples
were prepared on cleaned glass substrates and annealed at
various temperatures ranging form 95oC to 155oC. To obtain
the morphological and structural properties of VOPc thin
films, X-ray diffraction (XRD) technique and atomic force
microscopy (AFM) have been implied. The AFM topographic
images show a very slight difference in the thermally grown
films, before and after annealing, however best results are
achieved for the spin-cast film annealed at 125oC. The XRD
spectra show no existence of the sharp peaks, suggesting the
material to be amorphous. The humps in the XRD patterns
indicate the presence of some crystallites.
Abstract: Due to short product life cycles, increasing variety of
products and short cycles of leap innovations manufacturing
companies have to increase the flexibility of factory structures.
Flexibility of factory structures is based on defined factory planning
processes in which product, process and resource data of various
partial domains have to be considered. Thus factory planning
processes can be characterized as iterative, interdisciplinary and
participative processes [1]. To support interdisciplinary and
participative character of planning processes, a federative factory
data management (FFDM) as a holistic solution will be described.
FFDM is already implemented in form of a prototype. The interim
results of the development of FFDM will be shown in this paper. The
principles are the extracting of product, process and resource data
from documents of various partial domains providing as web services
on a server. The described data can be requested by the factory
planner by using a FFDM-browser.
Abstract: A new decomposition form is introduced in this report
to establish a criterion for the bi-partite separability of Bell diagonal
states. A such criterion takes a quadratic inequality of the coefficients
of a given Bell diagonal states and can be derived via a simple
algorithmic calculation of its invariants. In addition, the criterion can
be extended to a quantum system of higher dimension.
Abstract: Developing a university course schedule is
difficult. This is due to the limitations in the resources
available. The process is made even harder with different
faculties or departments having different ways of stating their
schedule requirements. The person in charge of taking the
schedule requirements and turning them into a proper course
schedule is not only burden with the task of allocating the
appropriate classes and time to lecturers and students, they
also need to understand the schedule requirements. Therefore
a scheduling support system named SATA is developed to
assist ICRESS in the course scheduling process. SATA has
been put to use for several semesters and the results have been
encouraging. It won a bronze medal in the 2008 Invention,
Innovation and Design competition (IID-08) and has been
submitted to be patented in October 2008
Abstract: Training with Functional Electrical Stimulation (FES)
has both physiological and psychological benefits for spinal cord
injured subjects. Commonly used methods for quantification of
spasticity have shown controversial reliability. In this study we
propose a method for quick determination of spasticity in spinal cord
injured subjects on a cycling and measurement system. 23 patients
did training sessions on an instrumented mobile FES cycle three
times a week over two months as part of their clinical rehabilitation
program. Spasticity (MAS) and the legs resistance to the pedaling
motion were assessed before and after the FES training and
measurements were done on the subjects ability to pedal with our
without motor assistance. Measurements with test persons with
incomplete spastic paraplegia have shown that spasticity is decreased
after a 30 min cycling training with functional electrical stimulation
(FES).
Abstract: The paper investigates the main issues concerning the activity of mergers and acquisitions in Romania in the period 2000- 2004. As in the first decade after the failure of the socialist economy the market of M&A was living its infancy based exclusively on privatization transactions, after 2000 the market entered in a stage of maturity. We are investigated both the registered evolutions in terms of number and value of transactions, and some sectoral issues, concerning the most important industries affected by the M&A process.
Abstract: Component-Based software engineering provides an
opportunity for better quality and increased productivity in software
development by using reusable software components [10]. One of the
most critical aspects of the quality of a software system is its
performance. The systematic application of software performance
engineering techniques throughout the development process can help
to identify design alternatives that preserve desirable qualities such
as extensibility and reusability while meeting performance objectives
[1]. In the present scenario, software engineering methodologies
strongly focus on the functionality of the system, while applying a
“fix- it-later" approach to software performance aspects [3]. As a
result, lengthy fine-tunings, expensive extra hard ware, or even
redesigns are necessary for the system to meet the performance
requirements. In this paper, we propose design based,
implementation independent, performance prediction approach to
reduce the overhead associated in the later phases while developing a
performance guaranteed software product with the help of Unified
Modeling Language (UML).