Abstract: Numerous experimental tests for post-installed anchor systems drilled in hardened concrete were conducted in order to estimate pull-out and shear strength accounting for uncertainties such as torque ratios, embedment depths and different diameters in demands. In this study, the strength of the systems was significantly changed by the effect of those three uncertainties during pull-out experimental tests, whereas the shear strength of the systems was not affected by torque ratios. It was also shown that concrete cone failure or damage mechanism was generally investigated during and after pull-out tests and in shear strength tests, mostly the anchor systems were failed prior to failure of primary structural system. Furthermore, 3D finite element model for the anchor systems was created by ABAQUS for the numerical analysis. The verification of finite element model was identical till the failure points to the load-displacement relationship specified by the experimental tests.
Abstract: Optical Coherence Tomography (OCT) combined
with the Confocal Microscopy, as a noninvasive method, permits the
determinations of materials defects in the ceramic layers depth. For
this study 256 anterior and posterior metal and integral ceramic fixed
partial dentures were used, made with Empress (Ivoclar), Wollceram
and CAD/CAM (Wieland) technology. For each investigate area 350
slices were obtain and a 3D reconstruction was perform from each
stuck. The Optical Coherent Tomography, as a noninvasive method,
can be used as a control technique in integral ceramic technology,
before placing those fixed partial dentures in the oral cavity. The
purpose of this study is to evaluate the capability of En face Optical
Coherence Tomography (OCT) combined with a fluorescent method
in detection and analysis of possible material defects in metalceramic
and integral ceramic fixed partial dentures. As a conclusion,
it is important to have a non invasive method to investigate fixed
partial prostheses before their insertion in the oral cavity in order to
satisfy the high stress requirements and the esthetic function.
Abstract: Corrugated wire mesh laminates (CWML) are a class
of engineered open cell structures that have potential for applications
in many areas including aerospace and biomedical engineering. Two
different methods of fabricating corrugated wire mesh laminates from
stainless steel, one using a high temperature Lithobraze alloy and the
other using a low temperature Eutectic solder for joining the
corrugated wire meshes are described herein. Their implementation is
demonstrated by manufacturing CWML samples of 304 and 316
stainless steel (SST). It is seen that due to the facility of employing
wire meshes of different densities and wire diameters, it is possible to
create CWML laminates with a wide range of effective densities. The
fabricated laminates are tested under uniaxial compression. The
variation of the compressive yield strength with relative density of the
CWML is compared to the theory developed by Gibson and Ashby for
open cell structures [22]. It is shown that the compressive strength of
the corrugated wire mesh laminates can be described using the same
equations by using an appropriate value for the linear coefficient in the
Gibson-Ashby model.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.
Abstract: This paper generalizes Yeh Lam-s shock model for
renewal shock arrivals and random threshold. Several interesting
statistical measures are explicitly obtained. A few special cases and
an optimal replacement problem are also discussed.
Abstract: In Lebanon, public construction projects are awarded
to the contractor submitting the lowest bid price based on a
competitive bidding process. The contractor has to make a strategic
decision in choosing the appropriate bid price that will offer a
satisfactory profit with a greater probability to win. A simulation
model for bid price decision making based on the lowest bid price
evaluation is developed. The model, built using Crystal Ball decisionengineering
software, considers two main factors affecting the
bidding process: the number of qualified bidders and the size of the
project. The validity of the model is tested on twelve separate
projects. The study also shows how to use the model to conduct risk
analysis and help any specific contractor to decide on his bid price
with associated certainty level in a scientific method.
Abstract: Compost manufacturing plants are one of units where
wastewater is produced in significantly large amounts. Wastewater
produced in these plants contains high amounts of substrate (organic
loads) and is classified as stringent waste which creates significant
pollution when discharged into the environment without treatment. A
compost production plant in the one of the Iran-s province treating
200 tons/day of waste is one of the most important environmental
pollutant operations in this zone. The main objectives of this paper
are to investigate the compost wastewater treatability in hybrid
anaerobic reactors with an upflow-downflow arrangement, to
determine the kinetic constants, and eventually to obtain an
appropriate mathematical model. After starting the hybrid anaerobic
reactor of the compost production plant, the average COD removal
rate efficiency was 95%.
Abstract: This work describes refrigeration effects during storage on total protein and amino acids composition of raw and processed flour of two pearl millet cultivars (Ashana and Dembi). The protein content of the whole raw flour was found to be 14.46 and 13.38% for Ashana and Dembi cultivars, respectively. Dehulling of the grains reduced the protein content to 13.38 and 12.67% for the cultivars, respectively. For both cultivars, the protein content of the whole and dehulled raw flour before and after cooking was slightly decreased when the flour was stored for 60 days even after refrigeration. The effect of refrigeration process in combination with the storage period, cooking or dehulling was found to be vary between amino acids and even between cultivars. Regardless of the storage period and processing method, the amino acids content was remained unchanged after refrigeration for both cultivars.
Abstract: The entomopathogenic nematodes Steinernema
feltiaeare are components of many biological pesticides. The
biological pesticides are applicated by means a spraying machines.
The influence of high pressure operating time on viability of
nematodes has been experimentally investigated in order to explain if
static pressure inside of the sprayers installation was able to destroy
nematodes. The value of pressure was 55 MPa and its maximum
operating time was 3 hours. Changes were found in viability of
pressurized samples of nematodes, mixed with water.
Abstract: Motivated by Microsoft Co. Academic Program
initiative, the department of Information Technology in King Saud
University has adopted Microsoft products in three courses. The
initiative aimed at enhancing the abilities of the university graduates
and equipping them with skills that would help them in the job
market. A number of methods of collecting assessment data were
used to evaluate the course adoption initiative. Assessment data
indicated that the goal of the course adoption is being achieved and
that the students were much better prepared to design applications
and administrate networks.
Abstract: This paper deals with the synthesis of fuzzy state feedback controller of induction motor with optimal performance. First, the Takagi-Sugeno (T-S) fuzzy model is employed to approximate a non linear system in the synchronous d-q frame rotating with electromagnetic field-oriented. Next, a fuzzy controller is designed to stabilise the induction motor and guaranteed a minimum disturbance attenuation level for the closed-loop system. The gains of fuzzy control are obtained by solving a set of Linear Matrix Inequality (LMI). Finally, simulation results are given to demonstrate the controller-s effectiveness.
Abstract: Both prognostic and diagnostic modes of a 3D baroclinic
model in hydrodynamic and sediment transport models of
the Princeton Ocean Model (POM) were conducted to separate
prognose and diagnose effects of different hydrodynamic factors on
transport of suspended sediment discharged from the rivers to the
Gulf of Thailand (GoT). Both transport modes of suspended sediment
distribution in the GoT were numerically simulated. It could be
concluded that the suspended sediment discharged from the rivers
around the GoT. Most of sediments in estuaries and coastal areas are
deposited outside the GoT under the condition of wind-driven current,
and very small amount of the sediments of them are transported
faraway. On the basis of wind forcing, sediments from the lower
GoT to the upper GoT are mainly transported south-northwestward
and also continuously moved north-southwestward. An obvious 3D
characteristic of suspended sediment transport is produced in the
wind-driven current residual circulation condition. In this study, the
transport patterns at the third layer are generally consistent with
the typhoon-induced strong currents in two case studies of Typhoon
Linda 1997. The case studies presented the prognostic and diagnostic
modes during 00UTC28OCT1997 to 12UTC06NOV1997 in a short
period with the current condition for pre-operation of the suspended
sediment transport model in estuaries and coastal areas.
Abstract: The adoption of e-learning in Hong Kong has been
increasing rapidly in the past decade. To understand the e-learning
experiences of the students, the School of Professional and Continuing
Education of The University of Hong Kong conducted a survey. The
survey aimed to collect students- experiences in using learning
management system, their perceived e-learning advantages, barriers in
e-learning and preferences in new e-learning development. A
questionnaire with 84 questions was distributed in mid 2012 and 608
valid responds were received. The analysis results showed that the
students found e-learning helpful to their study. They preferred
interactive functions and mobile features. Blended learning mode,
both face-to-face learning mode integrated with online learning and
face-to-face learning mode supplemented with online resources, were
preferred by the students. The results of experiences of Hong Kong
students in e-learning provided a contemporary reference to the
e-learning practitioners to understand the e-learning situation in Asia.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: In managing healthcare logistics, cost is not the only
factor to be considered. The level of items- criticality used in patient
care services plays an important role as well. A stock-out incident of
a high critical item could threaten a patient's life. In this paper, the
DMAIC (Define-Measure-Analyze-Improve-Control) methodology is
used to drive improvement projects based on customer driven critical
to quality characteristics at a Jordanian hospital. This paper shows
how the application of Six Sigma improves the performance of the
case hospital logistics system by reducing the number of stock-out
incidents.
Abstract: The aim of this research is to develop a fast and
reliable surveillance system based on a personal digital assistant
(PDA) device. This is to extend the capability of the device to detect
moving objects which is already available in personal computers.
Secondly, to compare the performance between Background
subtraction (BS) and Temporal Frame Differencing (TFD) techniques
for PDA platform as to which is more suitable. In order to reduce
noise and to prepare frames for the moving object detection part,
each frame is first converted to a gray-scale representation and then
smoothed using a Gaussian low pass filter. Two moving object
detection schemes i.e., BS and TFD have been analyzed. The
background frame is updated by using Infinite Impulse Response
(IIR) filter so that the background frame is adapted to the varying
illuminate conditions and geometry settings. In order to reduce the
effect of noise pixels resulting from frame differencing
morphological filters erosion and dilation are applied. In this
research, it has been found that TFD technique is more suitable for
motion detection purpose than the BS in term of speed. On average
TFD is approximately 170 ms faster than the BS technique
Abstract: Writer identification is one of the areas in pattern
recognition that attract many researchers to work in, particularly in
forensic and biometric application, where the writing style can be
used as biometric features for authenticating an identity. The
challenging task in writer identification is the extraction of unique
features, in which the individualistic of such handwriting styles
can be adopted into bio-inspired generalized global shape for
writer identification. In this paper, the feasibility of generalized
global shape concept of complimentary binding in Artificial
Immune System (AIS) for writer identification is explored. An
experiment based on the proposed framework has been conducted
to proof the validity and feasibility of the proposed approach for
off-line writer identification.
Abstract: In 2011, Debiao et al. pointed out that S-3PAKE protocol proposed by Lu and Cao for password-authenticated key exchange in the three-party setting is vulnerable to an off-line dictionary attack. Then, they proposed some countermeasures to eliminate the security vulnerability of the S-3PAKE. Nevertheless, this paper points out their enhanced S-3PAKE protocol is still vulnerable to undetectable on-line dictionary attacks unlike their claim.
Abstract: In a graph G, a cycle is Hamiltonian cycle if it contain all vertices of G. Two Hamiltonian cycles C_1 = 〈u_0, u_1, u_2, ..., u_{n−1}, u_0〉 and C_2 = 〈v_0, v_1, v_2, ..., v_{n−1}, v_0〉 in G are independent if u_0 = v_0, u_i = ̸ v_i for all 1 ≤ i ≤ n−1. In G, a set of Hamiltonian cycles C = {C_1, C_2, ..., C_k} is mutually independent if any two Hamiltonian cycles of C are independent. The mutually independent Hamiltonicity IHC(G), = k means there exist a maximum integer k such that there exists k-mutually independent Hamiltonian cycles start from any vertex of G. In this paper, we prove that IHC(C_n × C_n) = 4, for n ≥ 3.
Abstract: Camera calibration plays an important role in the domain of the analysis of sports video. Considering soccer video, in most cases, the cross-points can be used for calibration at the center of the soccer field are not sufficient, so this paper introduces a new automatic camera calibration algorithm focus on solving this problem by using the properties of images of the center circle, halfway line and a touch line. After the theoretical analysis, a practicable automatic algorithm is proposed. Very little information used though, results of experiments with both synthetic data and real data show that the algorithm is applicable.