Abstract: Delays in the construction industry are a global phenomenon. Many construction projects experience extensive delays exceeding the initially estimated completion time. The main purpose of this study is to identify construction projects typical behaviors in order to develop a prognosis and management tool. Being able to know a construction projects schedule tendency will enable evidence-based decision-making to allow resolutions to be made before delays occur. This study presents an innovative approach that uses Cluster Analysis Method to support predictions during Earned Value Analyses. A clustering analysis was used to predict future scheduling, Earned Value Management (EVM), and Earned Schedule (ES) principal Indexes behaviors in construction projects. The analysis was made using a database with 90 different construction projects. It was validated with additional data extracted from literature and with another 15 contrasting projects. For all projects, planned and executed schedules were collected and the EVM and ES principal indexes were calculated. A complete linkage classification method was used. In this way, the cluster analysis made considers that the distance (or similarity) between two clusters must be measured by its most disparate elements, i.e. that the distance is given by the maximum span among its components. Finally, through the use of EVM and ES Indexes and Tukey and Fisher Pairwise Comparisons, the statistical dissimilarity was verified and four clusters were obtained. It can be said that construction projects show an average delay of 35% of its planned completion time. Furthermore, four typical behaviors were found and for each of the obtained clusters, the interim milestones and the necessary rhythms of construction were identified. In general, detected typical behaviors are: (1) Projects that perform a 5% of work advance in the first two tenths and maintain a constant rhythm until completion (greater than 10% for each remaining tenth), being able to finish on the initially estimated time. (2) Projects that start with an adequate construction rate but suffer minor delays culminating with a total delay of almost 27% of the planned time. (3) Projects which start with a performance below the planned rate and end up with an average delay of 64%, and (4) projects that begin with a poor performance, suffer great delays and end up with an average delay of a 120% of the planned completion time. The obtained clusters compose a tool to identify the behavior of new construction projects by comparing their current work performance to the validated database, thus allowing the correction of initial estimations towards more accurate completion schedules.
Abstract: The use of nanostructured semiconducting material to catalyze degradation of environmental pollutants still receives much attention to date. One of the desired characteristics for pollutant degradation under ultra-violet visible light is the materials with extended carrier charge separation that allows for electronic transfer between the catalyst and the pollutants. In this work, zinc oxide n-type semiconductor vertically aligned structures were fabricated on silicon (100) substrates using the chemical bath deposition method. The as-synthesized structures were treated with nickel and sulphur. X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy were used to characterize the phase purity, structural dimensions and elemental composition of the obtained structures respectively. Photoluminescence emission measurements showed a decrease in both the near band edge emission as well as the defect band emission upon addition of nickel and sulphur with different concentrations. This was attributed to increased charger-carrier-separation due to the presence of Ni-S material on ZnO surface, which is linked to improved charge transfer during photocatalytic reactions.
Abstract: The majority of today’s mobile robots are very dependent on battery power. Mobile robots can operate untethered for a number of hours but eventually they will need to recharge their batteries in-order to continue to function. While computer processing and sensors have become cheaper and more powerful each year, battery development has progress very little. They are slow to re-charge, inefficient and lagging behind in the general progression of robotic development we see today. However, batteries are relatively cheap and when fully charged, can supply high power output necessary for operating heavy mobile robots. As there are no cheap alternatives to batteries, we need to find efficient ways to manage the power that batteries provide during their operational lifetime. This paper proposes the use of autonomic principles of self-adaption to address the behavioral changes a battery experiences as it gets older. In life, as we get older, we cannot perform tasks in the same way as we did in our youth; these tasks generally take longer to perform and require more of our energy to complete. Batteries also suffer from a form of degradation. As a battery gets older, it loses the ability to retain the same charge capacity it would have when brand new. This paper investigates how we can adapt the current state of a battery charge and cycle count, to the requirements of a mobile robot to perform its tasks.
Abstract: Rainfall and runoff phenomenon is a chaotic and complex outcome of nature which requires sophisticated modelling and simulation methods for explanation and use. Time Series modelling allows runoff data analysis and can be used as forecasting tool. In the paper attempt is made to model river runoff data and predict the future behavioural pattern of river based on annual past observations of annual river runoff. The river runoff analysis and predict are done using ARIMA model. For evaluating the efficiency of prediction to hydrological events such as rainfall, runoff and etc., we use the statistical formulae applicable. The good agreement between predicted and observation river runoff coefficient of determination (R2) display that the ARIMA (4,1,1) is the suitable model for predicting Karkheh River runoff at Iran.
Abstract: Cellulose acetate (CA) is a natural biodegradable polymer. It forms transparent films by the casting technique. CA suffers from high degree of water permeability as well as the low thermal stability at high temperatures. To adjust the CA polymeric films to the manufacture of food packaging, its thermal and mechanical properties should be improved. The modification of CA by grafting it with N-Amino phenyl maleimide (N-APhM) led to the construction of hydrophobic branches throughout the polymeric matrix which reduced its wettability as compared to the parent CA. The branches built onto the polymeric chains had been characterized by UV/Vis, 13C-NMR and ESEM. The improvement of the thermal properties was investigated and compared to the parent CA using thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), differential thermal analysis (DTA), contact angle and mechanical testing measurements. The results revealed that the water-uptake was reduced by increasing the graft percentage. The thermal and mechanical properties were also improved.
Abstract: With the increasing demand of bandwidth and data rate,
there is a dire need to implement antenna systems in mobile phones
which are able to fulfill user requirements. A monopole antenna
system with multi-antennas configurations is proposed considering
the feasibility and user demand. The multi-antenna structure is
referred to as multi-input multi-output (MIMO) antenna system. The
multi-antenna system comprises of 4 antennas operating below 6
GHz frequency bands for 4G/LTE and 4 antenna for 5G applications
at 28 GHz and the dimension of board is 120 × 70 × 0.8mm3.
The suggested designs is feasible with a structure of low-profile
planar-antenna and is adaptable to smart cell phones and handheld
devices. To the best of our knowledge, this is the first design
compared to the literature by having integrated antenna system
for two standards, i.e., 4G and 5G. All MIMO antenna systems
are simulated on commercially available software, which is high
frequency structures simulator (HFSS).
Abstract: In this paper, a method of fast 3D topography modeling using the high-resolution camera images is studied based on the characteristics of Unmanned Aerial Vehicle (UAV) system for low altitude aerial photogrammetry and the need of three dimensional (3D) urban landscape modeling. Firstly, the existing high-resolution digital camera with special design of overlap images is designed by reconstructing and analyzing the auto-flying paths of UAVs, which improves the self-calibration function to achieve the high precision imaging by software, and further increased the resolution of the imaging system. Secondly, several-angle images including vertical images and oblique images gotten by the UAV system are used for the detail measure of urban land surfaces and the texture extraction. Finally, the aerial photography and 3D topography construction are both developed in campus of Chang-Jung University and in Guerin district area in Tainan, Taiwan, provide authentication model for construction of 3D topography based on combined UAV-based camera images from system. The results demonstrated that the UAV system for low altitude aerial photogrammetry can be used in the construction of 3D topography production, and the technology solution in this paper offers a new, fast, and technical plan for the 3D expression of the city landscape, fine modeling and visualization.
Abstract: Lead contamination of agricultural land mainly vegetated with perennial ryegrass (Lolium perenne) has been investigated. The metal derived from the discharge of sludge from a ceramic industry in the past had used lead paints. The results showed very high values of lead concentration in many soil samples. In order to assess the lead soil contamination, a sequential extraction with H2O, KNO3, EDTA was performed, and the chemical forms of lead in the soil were evaluated. More than 70% of lead was in a potentially bioavailable form. Analysis of Lolium perenne showed elevated lead concentration. A Freundlich-like model was used to describe the transferability of the metal from the soil to the plant.
Abstract: Crank shaft length, connecting rod length, crank angle, engine rpm, cylinder bore, mass of piston and compression ratio are the inputs that can control the performance of the slider crank mechanism and then its efficiency. Several combinations of these seven inputs are used and compared. The throughput engine torque predicted by the simulation is analyzed through two different regression models, with and without interaction terms, developed according to multi-linear regression using LU decomposition to solve system of algebraic equations. These models are validated. A regression model in seven inputs including their interaction terms lowered the polynomial degree from 3rd degree to 1st degree and suggested valid predictions and stable explanations.
Abstract: Water supply and sanitation in Saudi Arabia is portrayed by difficulties and accomplishments. One of the fundamental difficulties is water shortage. With a specific end goal to beat water shortage, significant ventures have been attempted in sea water desalination, water circulation, sewerage, and wastewater treatment. The motivation behind Statistical Process Control (SPC) is to decide whether the execution of a procedure is keeping up an acceptable quality level [AQL]. SPC is an analytical decision-making method. A fundamental apparatus in the SPC is the Control Charts, which follow the inconstancy in the estimations of the item quality attributes. By utilizing the suitable outline, administration can decide whether changes should be made with a specific end goal to keep the procedure in charge. The two most important quality factors in the distilled water which were taken into consideration were pH (Potential of Hydrogen) and TDS (Total Dissolved Solids). There were three stages at which the quality checks were done. The stages were as follows: (1) Water at the source, (2) water after chemical treatment & (3) water which is sent for packing. The upper specification limit, central limit and lower specification limit are taken as per Saudi water standards. The procedure capacity to accomplish the particulars set for the quality attributes of Berain water Factory chose to be focused by the proposed SPC system.
Abstract: The advancement in various concrete ingredients like plasticizers, additives and fibers, etc. has enabled concrete technologists to develop many viable varieties of special concretes in recent decades. Such various varieties of concrete have significant enhancement in green as well as hardened properties of concrete. A prudent selection of appropriate type of concrete can resolve many design and application issues in construction projects. This paper focuses on usage of self-compacting concrete, high early strength concrete, structural lightweight concrete, fiber reinforced concrete, high performance concrete and ultra-high strength concrete in the structures. The modified properties of strength at various ages, flowability, porosity, equilibrium density, flexural strength, elasticity, permeability etc. need to be carefully studied and incorporated into the design of the structures. The paper demonstrates various mixture combinations and the concrete properties that can be leveraged. The selection of such products based on the end use of structures has been proposed in order to efficiently utilize the modified characteristics of these concrete varieties. The study involves mapping the characteristics with benefits and savings for the structure from design perspective. Self-compacting concrete in the structure is characterized by high shuttering loads, better finish, and feasibility of closer reinforcement spacing. The structural design procedures can be modified to specify higher formwork strength, height of vertical members, cover reduction and increased ductility. The transverse reinforcement can be spaced at closer intervals compared to regular structural concrete. It allows structural lightweight concrete structures to be designed for reduced dead load, increased insulation properties. Member dimensions and steel requirement can be reduced proportionate to about 25 to 35 percent reduction in the dead load due to self-weight of concrete. Steel fiber reinforced concrete can be used to design grade slabs without primary reinforcement because of 70 to 100 percent higher tensile strength. The design procedures incorporate reduction in thickness and joint spacing. High performance concrete employs increase in the life of the structures by improvement in paste characteristics and durability by incorporating supplementary cementitious materials. Often, these are also designed for slower heat generation in the initial phase of hydration. The structural designer can incorporate the slow development of strength in the design and specify 56 or 90 days strength requirement. For designing high rise building structures, creep and elasticity properties of such concrete also need to be considered. Lastly, certain structures require a performance under loading conditions much earlier than final maturity of concrete. High early strength concrete has been designed to cater to a variety of usages at various ages as early as 8 to 12 hours. Therefore, an understanding of concrete performance specifications for special concrete is a definite door towards a superior structural design approach.
Abstract: The latent heat thermal energy storage system is a
thrust area of research due to exuberant thermal energy storage
potential. The thermal performance of PCM is significantly
augmented by installation of the high thermal conductivity fins. The
objective of the present study is to obtain optimum size and location
of the fins to enhance diffusion heat transfer without altering overall
melting time. Hence, the constructal theory is employed to eliminate,
resize, and re-position the fins. A numerical code based on conjugate
heat transfer coupled enthalpy porosity approached is developed to
solve Navier-Stoke and energy equation. The numerical results show
that the constructal fin design has enhanced the thermal performance
along with the increase in the overall volume of PCM when
compared to conventional. The overall volume of PCM is found to be
increased by half of total of volume of fins. The elimination and repositioning
the fins at high temperature gradient from low
temperature gradient is found to be vital.
Abstract: As part of a ‘Morphing-Wing’ idea, this study consists
of measuring how a winglet, which is able to change its shape during
the flight, is efficient. Conventionally, winglets are fixed-vertical
platforms at the wingtips, optimized for a cruise condition that the
airplane should use most of the time. However, during a cruise, an
airplane flies through a lot of cruise conditions corresponding to
altitudes variations from 30,000 to 45,000 ft. The fixed winglets are
not optimized for these variations, and consequently, they are
supposed to generate some drag, and thus to deteriorate aircraft fuel
consumption. This research assumes that it exists a winglet position
that reduces the fuel consumption for each cruise condition. In this
way, the methodology aims to find these optimal winglet positions,
and to further simulate, and thus estimate the fuel consumption of an
aircraft wearing this type of adaptive winglet during several cruise
conditions. The adaptive winglet is assumed to have degrees of
freedom given by the various changes of following surfaces: the tip
chord, the sweep and the dihedral angles. Finally, results obtained
during cruise simulations are presented in this paper. These results
show that an adaptive winglet can reduce, thus improve up to 2.12%
the fuel consumption of an aircraft during a cruise.
Abstract: The discussion about elements of cultural heritage and
their relevance among the ancient villages is comparably insufficient.
The protection work is strongly influenced by touristic development
and cultural gimmick, resulting in low protection efficiency and many
omissions. Historical villages as the cultural settlement patterns bear a
large number of heritage relics. They were regionally scattered with a
clear characteristic of gathering. First of all, this study proposes the
association and similarities of the forming mechanism between four
historic cultural villages in Mian Mountain. Secondly, the study
reveals that these villages own the strategic pass, underground
passage, and the mountain barrier. Thirdly, based on the differentiated
characteristics of villages’ space, the study discusses about the
integrated conservation from three levels: the regional heritage
conservation, the cultural line shaping, and the featured brand
building.
Abstract: The purpose of the present research is to equate two
test forms as part of a study to evaluate the educational effectiveness
of the ARTé: Mecenas art history learning game. The researcher
applied Item Response Theory (IRT) procedures to calculate item,
test, and mean-sigma equating parameters. With the sample size
n=134, test parameters indicated “good” model fit but low Test
Information Functions and more acute than expected equating
parameters. Therefore, the researcher applied equipercentile equating
and linear equating to raw scores and compared the equated form
parameters and effect sizes from each method. Item scaling in IRT
enables the researcher to select a subset of well-discriminating items.
The mean-sigma step produces a mean-slope adjustment from the
anchor items, which was used to scale the score on the new form
(Form R) to the reference form (Form Q) scale. In equipercentile
equating, scores are adjusted to align the proportion of scores in each
quintile segment. Linear equating produces a mean-slope adjustment,
which was applied to all core items on the new form. The study
followed a quasi-experimental design with purposeful sampling of
students enrolled in a college level art history course (n=134) and
counterbalancing design to distribute both forms on the pre- and posttests.
The Experimental Group (n=82) was asked to play ARTé:
Mecenas online and complete Level 4 of the game within a two-week
period; 37 participants completed Level 4. Over the same period, the
Control Group (n=52) did not play the game. The researcher
examined between group differences from post-test scores on test
Form Q and Form R by full-factorial Two-Way ANOVA. The raw
score analysis indicated a 1.29% direct effect of form, which was
statistically non-significant but may be practically significant. The
researcher repeated the between group differences analysis with all
three equating methods. For the IRT mean-sigma adjusted scores,
form had a direct effect of 8.39%. Mean-sigma equating with a small
sample may have resulted in inaccurate equating parameters.
Equipercentile equating aligned test means and standard deviations,
but resultant skewness and kurtosis worsened compared to raw score
parameters. Form had a 3.18% direct effect. Linear equating
produced the lowest Form effect, approaching 0%. Using linearly
equated scores, the researcher conducted an ANCOVA to examine
the effect size in terms of prior knowledge. The between group effect
size for the Control Group versus Experimental Group participants
who completed the game was 14.39% with a 4.77% effect size
attributed to pre-test score. Playing and completing the game
increased art history knowledge, and individuals with low prior
knowledge tended to gain more from pre- to post test. Ultimately,
researchers should approach test equating based on their theoretical
stance on Classical Test Theory and IRT and the respective assumptions. Regardless of the approach or method, test equating
requires a representative sample of sufficient size. With small sample
sizes, the application of a range of equating approaches can expose
item and test features for review, inform interpretation, and identify
paths for improving instruments for future study.
Abstract: Tire noise has a significant impact on ride quality
and vehicle interior comfort, even at low frequency. Reduction of
tire noise is especially important due to strict state and federal
environmental regulations. The primary sources of tire noise are the
low frequency structure-borne noise and the noise that originates from
the release of trapped air between the tire tread and road surface
during each revolution of the tire. The frequency response of the tire
changes at low and high frequency. At low frequency, the tension
and bending moment become dominant, while the internal structure
and local deformation become dominant at higher frequencies. Here,
we analyze tire response in terms of deformation and rolling velocity
at low revolution frequency. An Abaqus FEA finite element model
is used to calculate the static and dynamic response of a rolling tire
under different rolling conditions. The natural frequencies and mode
shapes of a deformed tire are calculated with the FEA package where
the subspace-based steady state dynamic analysis calculates dynamic
response of tire subjected to harmonic excitation. The analysis was
conducted on the dynamic response at the road (contact point of tire
and road surface) and side nodes of a static and rolling tire when
the tire was excited with 200 N vertical load for a frequency ranging
from 20 to 200 Hz. The results show that frequency has little effect on
tire deformation up to 80 Hz. But between 80 and 200 Hz, the radial
and lateral components of displacement of the road and side nodes
exhibited significant oscillation. For the static analysis, the fluctuation
was sharp and frequent and decreased with frequency. In contrast, the
fluctuation was periodic in nature for the dynamic response of the
rolling tire. In addition to the dynamic analysis, a steady state rolling
analysis was also performed on the tire traveling at ground velocity
with a constant angular motion. The purpose of the computation
was to demonstrate the effect of rotating motion on deformation and
rolling velocity with respect to a fixed Newtonian reference point.
The analysis showed a significant variation in deformation and rolling
velocity due to centrifugal and Coriolis acceleration with respect to
a fixed Newtonian point on ground.
Abstract: Jesus and Socrates shared a remarkable gift; a channel of inner spiritual communication, to afford them truthful guidance in their respective religious discourse. Jesus is part of the Trinity; he is the Son, the Son of God. In mortal life he is the son of a carpenter. He called on all peoples to repent of their sins but fell foul of the authorities and was crucified. Socrates was an ancient Greek philosopher and the son of an artisan. His mission is to drive the Athenians to investigate truth, but he too incurs the displeasure of fellow citizens, to the extent of execution. The accusations made against them centre around, in Jesus’ case, proclaiming himself the Son of God, with the means to pardon, and in Socrates’, that a daimonion, an inner voice, speaks to him in his heart. Jesus talks with God directly through prayer, as the pneuma of God, i.e. to pneuma to hagion, or Holy Spirit, is with him. Socrates seems to enter what we would now think of as a trance-like condition, wherein he communicates with his inner daimonion, who directs him to take courage on the righteous path.
Abstract: In this paper, the velocity potential and stream
function of capture zone for a well field in an aquifer bounded by two
parallel streams with or without a uniform regional flow of any
directions are presented. The well field includes any number of
extraction or injection wells or a combination of both types with any
pumping rates. To delineate the capture envelope, the potential and
streamlines equations are derived by conformal mapping method.
This method can help us to release constrains of other methods. The
equations can be applied as useful tools to design in-situ groundwater
remediation systems, to evaluate the surface–subsurface water
interaction and to manage the water resources.
Abstract: The Extended Enterprise Resource Planning (ERPII)
system usually requires massive amounts of storage space, powerful
servers, and large upfront and ongoing investments to purchase and
manage the software and the related hardware which are not
affordable for organizations. In recent decades, organizations prefer
to adapt their business structures with new technologies for
remaining competitive in the world economy. Therefore, cloud
computing (which is one of the tools of information technology (IT))
is a modern system that reveals the next-generation application
architecture. Also, cloud computing has had some advantages that
reduce costs in many ways such as: lower upfront costs for all
computing infrastructure and lower cost of maintaining and
supporting. On the other hand, traditional ERPII is not responding for
huge amounts of data and relations between the organizations. In this
study, based on a literature study, ERPII is investigated in the context
of cloud computing where the organizations operate more efficiently.
Also, ERPII conditions have a response to needs of organizations in
large amounts of data and relations between the organizations.
Abstract: The IEEE 802.15.4 standard is designed for low-rate wireless personal area networks (LR-WPAN) with focus on enabling wireless sensor networks. It aims to give a low data rate, low power consumption, and low cost wireless networking on the device-level communication. The objective of this study is to investigate the performance of IEEE 802.15.4 based networks using simulation tool. In this project the network simulator 2 NS2 was used to several performance measures of wireless sensor networks. Three scenarios were considered, multi hop network with a single coordinator, star topology, and an ad hoc on demand distance vector AODV. Results such as packet delivery ratio, hop delay, and number of collisions are obtained from these scenarios.