Abstract: Microstructural and electrical properties of
Cu-chromium alloy (Cu-Cr) dispersed with vapor-grown carbon fiber
(VGCF) prepared by powder metallurgy (P/M) process have been
investigated. Cu-0.7 mass% Cr pre-alloyed powder (Cu-Cr) made by
water atomization process was used as raw materials, which contained
solid solute Cr elements in Cu matrix. The alloy powder coated with
un-bundled VGCF by using oil coating process was consolidated at
1223 K in vacuum by spark plasma sintering, and then extruded at
1073 K. The extruded Cu-Cr alloy (monolithic alloy) had 209.3 MPa
YS and 80.4 IACS% conductivity. The extruded Cu-Cr with 0.1
mass% VGCF composites revealed a small decrease of YS compared
to the monolithic Cu-Cr alloy. On the other hand, the composite had a
higher electrical conductivity than that of the monolithic alloy. For
example, Cu-Cr with 0.1 mass% VGCF composite sintered for 5 h
showed 182.7 MPa YS and 89.7 IACS% conductivity. In the case of
Cu-Cr with VGCFs composites, the Cr concentration was observed
around VGCF by SEM-EDS analysis, where Cr23C6 compounds were
detected by TEM observation. The amount of Cr solid solution in the
matrix of the Cu-Cr composites alloy was about 50% compared to the
monolithic Cu-Cr sintered alloy, and resulted in the remarkable
increment of the electrical conductivity.
Abstract: Experimental studies to investigate the depth of the
scour conducted at a side-weir intersection located at the 1800 curved
flume which located Hydraulic Laboratory of Yıldız Technical
University, Istanbul, Turkey. Side weirs were located at the middle of
the straight part of the main channel. Three different lengths (25, 40
and 50 cm) and three different weir crest height (7, 10 and 12 cm) of
the side weir placed on the side weir station. There is no scour when
the material is only kaolin. Therefore, the cohesive bed was prepared
by properly mixing clay material (kaolin) with 31% sand in all
experiments. Following 24h consolidation time, in order to observe
the effect of flow intensity on the scour depth, experiments were
carried out for five different upstream Froude numbers in the range of
0.33-0.81.
As a result of this study the relation between scour depth and
upstream flow intensity as a function of time have been established.
The longitudinal velocities decreased along the side weir; towards the
downstream due to overflow over the side-weirs. At the beginning,
the scour depth increases rapidly with time and then asymptotically
approached constant values in all experiments for all side weir
dimensions as in non-cohesive sediment. Thus, the scour depth
reached equilibrium conditions. Time to equilibrium depends on the
approach flow intensity and the dimensions of side weirs. For
different heights of the weir crest, dimensionless scour depths
increased with increasing upstream Froude number. Equilibrium
scour depths which formed 7 cm side-weir crest height were obtained
higher than that of the 12 cm side-weir crest height. This means when
side-weir crest height increased equilibrium scour depths decreased.
Although the upstream side of the scour hole is almost vertical, the
downstream side of the hole is inclined.
Abstract: Purpose: The study aimed to assess the depressant or
antidepressant effects of several Nonsteroidal Anti-Inflammatory
Drugs (NSAIDs) in mice: the selective cyclooxygenase-2 (COX-2)
inhibitor meloxicam, and the non-selective COX-1 and COX-2
inhibitors lornoxicam, sodium metamizole, and ketorolac. The
current literature data regarding such effects of these agents are
scarce.
Materials and methods: The study was carried out on NMRI mice
weighing 20-35 g, kept in a standard laboratory environment. The
study was approved by the Ethics Committee of the University of
Medicine and Pharmacy „Carol Davila”, Bucharest. The study agents
were injected intraperitoneally, 10 mL/kg body weight (bw) 1 hour
before the assessment of the locomotor activity by cage testing (n=10
mice/ group) and 2 hours before the forced swimming tests (n=15).
The study agents were dissolved in normal saline (meloxicam,
sodium metamizole), ethanol 11.8% v/v in normal saline (ketorolac),
or water (lornoxicam), respectively. Negative and positive control
agents were also given (amitryptilline in the forced swimming test).
The cage floor used in the locomotor activity assessment was divided
into 20 equal 10 cm squares. The forced swimming test involved
partial immersion of the mice in cylinders (15/9cm height/diameter)
filled with water (10 cm depth at 28C), where they were left for 6
minutes. The cage endpoint used in the locomotor activity assessment
was the number of treaded squares. Four endpoints were used in the
forced swimming test (immobility latency for the entire 6 minutes,
and immobility, swimming, and climbing scores for the final 4
minutes of the swimming session), recorded by an observer that was
„blinded” to the experimental design. The statistical analysis used the
Levene test for variance homogeneity, ANOVA and post-hoc
analysis as appropriate, Tukey or Tamhane tests.
Results: No statistically significant increase or decrease in the
number of treaded squares was seen in the locomotor activity
assessment of any mice group. In the forced swimming test,
amitryptilline showed an antidepressant effect in each experiment, at
the 10 mg/kg bw dosage. Sodium metamizole was depressant at 100
mg/kg bw (increased the immobility score, p=0.049, Tamhane test),
but not in lower dosages as well (25 and 50 mg/kg bw). Ketorolac
showed an antidepressant effect at the intermediate dosage of 5
mg/kg bw, but not so in the dosages of 2.5 and 10 mg/kg bw,
respectively (increased the swimming score, p=0.012, Tamhane test).
Meloxicam and lornoxicam did not alter the forced swimming
endpoints at any dosage level.
Discussion: 1) Certain NSAIDs caused changes in the forced
swimming patterns without interfering with locomotion. 2) Sodium
metamizole showed a depressant effect, whereas ketorolac proved
antidepressant. Conclusion: NSAID-induced mood changes are not
class effects of these agents and apparently are independent of the
type of inhibited cyclooxygenase (COX-1 or COX-2).
Disclosure: This paper was co-financed from the European Social
Fund, through the Sectorial Operational Programme Human Resources Development 2007-2013, project number POSDRU /159
/1.5 /S /138907 "Excellence in scientific interdisciplinary research,
doctoral and postdoctoral, in the economic, social and medical fields
-EXCELIS", coordinator The Bucharest University of Economic
Studies.
Abstract: The aim of the current study was to develop and
validate a Response to Stressful Situations Scale (RSSS) for the
Portuguese population. This scale assesses the degree of stress
experienced in scenarios that can constitute positive, negative and
more neutral stressors, and also describes the physiological,
emotional and behavioral reactions to those events according to their
intensity. These scenarios include typical stressor scenarios relevant
to patients with schizophrenia, which are currently absent from most
scales, assessing specific risks that these stressors may bring on
subjects, which may prove useful in non-clinical and clinical
populations (i.e. Patients with mood or anxiety disorders,
schizophrenia). Results from Principal Components Analysis and
Confirmatory Factor Analysis of two adult samples from general
population allowed to confirm a three-factor model with good fit
indices: χ2 (144)= 370.211, p = 0.000; GFI = 0.928; CFI = 0.927; TLI =
0.914, RMSEA = 0.055, P(rmsea ≤0.005) = .096; PCFI = .781.
Further data analysis of the scale revealed that RSSS is an adequate
assessment tool of stress response in adults to be used in further
research and clinical settings, with good psychometric characteristics,
adequate divergent and convergent validity, good temporal stability
and high internal consistency.
Abstract: In this paper, we propose a system for preventing gas
risks through the use of wireless communication modules and
intelligent gas safety appliances. Our system configuration consists of
an automatic extinguishing system, detectors, a wall-pad, and a
microcomputer controlled micom gas meter to monitor gas flow and
pressure as well as the occurrence of earthquakes. The automatic fire
extinguishing system checks for both combustible gaseous leaks and
monitors the environmental temperature, while the detector array
measures smoke and CO gas concentrations. Depending on detected
conditions, the micom gas meter cuts off an inner valve and generates
a warning, the automatic fire-extinguishing system cuts off an external
valve and sprays extinguishing materials, or the sensors generate
signals and take further action when smoke or CO are detected.
Information on intelligent measures taken by the gas safety appliances
and sensors are transmitted to the wall-pad, which in turn relays this as
real time data to a server that can be monitored via an external network
(BcN) connection to a web or mobile application for the management
of gas safety. To validate this smart-home gas management system, we
field-tested its suitability for use in Korean apartments under several
scenarios.
Abstract: Phthalates are ubiquitous environmental pollutants
well known because of their endocrine disrupting activity in human
organism. The aim of our study was, by biological monitoring,
investigate exposure to phthalates of Roma ethnicity group i.e.
children and adults from 5 families (n=29, average age 11.8 ± 7.6
years) living in western Slovakia. Additionally, we analysed some
associations between anthropometric measures, questionnaire data
i.e. socio-economic status, eating and drinking habits, practise of
personal care products and household conditions in comparison with
concentrations of phthalate metabolites. We used for analysis of urine
samples high performance liquid chromatography and tandem mass
spectrometry (HPLC-MS/MS) to determine concentrations of
phthalate metabolites monoethyl phthalate (MEP), mono-n-butyl
phthalate (MnBP), mono-iso-butyl phthalate (MiBP), mono(2-ethyl-
5-hydroxyhexyl) phthalate (5OH-MEHP), mono(2-ethyl-5-oxohexyl)
phthalate (5oxo-MEHP) and mono(2-etylhexyl) phthalate (MEHP).
Our results indicate that ethnicity, lower socioeconomic status and
different housing conditions in Roma population can affect urinary
concentration of phthalate metabolites.
Abstract: As the trend in automotive technology is fast moving
towards hybridization and electrification to curb emissions as well as
to improve the fuel efficiency, air-conditioning systems in passenger
cars have not caught up with this trend and still remain as the major
energy consumers amongst others. Adsorption based air-conditioning
systems, e.g. with silica-gel water pair, which are already in use for
residential and commercial applications, are now being considered as
a technology leap once proven feasible for the passenger cars. In this
paper we discuss a methodology, challenges and feasibility of
implementing an adsorption based air-conditioning system in a
passenger car utilizing the exhaust waste heat. We also propose an
optimized control strategy with interfaces to the engine control unit
of the vehicle for operating this system with reasonable efficiency
supported by our simulation and validation results in a prototype
vehicle, additionally comparing to existing implementations,
simulation based as well as experimental. Finally we discuss the
influence of start-stop and hybrid systems on the operation strategy of
the adsorption air-conditioning system.
Abstract: All current experimental methods for determination of
stress intensity factors are based on the assumption that the state of
stress near the crack tip is plane stress. Therefore, these methods rely
on strain and displacement measurements made outside the near
crack tip region affected by the three-dimensional effects or by
process zone. In this paper, we develop and validate an experimental
procedure for the evaluation of stress intensity factors from the
measurements of the out-of-plane displacements in the surface area
controlled by 3D effects. The evaluation of stress intensity factors is
possible when the process zone is sufficiently small, and the
displacement field generated by the 3D effects is fully encapsulated
by K-dominance region.
Abstract: The changes of the optical and structural properties of
Bismuth-Boro-Tellurite glasses pre and post gamma irradiation were
studied. Six glass samples, with different composition [(TeO2)0.7
(B2O3)0.3]1-x (Bi2O3)x prepared by melt quenching method were
irradiated with 25kGy gamma radiation at room temperature. The
Fourier Transform Infrared Spectroscopy (FTIR) was used to explore
the structural bonding in the prepared glass samples due to exposure,
while UV-VIS Spectrophotometer was used to evaluate the changes
in the optical properties before and after irradiation. Gamma
irradiation causes profound changes in the peak intensity as shown by
FTIR spectra which is due to the breaking of the network bonding.
Before gamma irradiation, the optical band gap, Eg value decreased
from 2.44 eV to 2.15 eV with the addition of Bismuth content. The
value kept decreasing (from 2.18 eV to 2.00 eV) following exposure
to gamma radiation due to the increase of non-bridging oxygen
(NBO) and the increase of defect in the glass. In conclusion, the glass
with high content of Bi2O3 (0.30Bi) give smallest Eg and show less
changes in FTIR spectra after gamma irradiation which indicate that
this glass is more resistant to gamma radiation compared to other
glasses.
Abstract: In this work, we explore the capability of the mean
shift algorithm as a powerful preprocessing tool for improving the
quality of spatial data, acquired from airborne scanners, from densely
built urban areas. On one hand, high resolution image data corrupted
by noise caused by lossy compression techniques are appropriately
smoothed while at the same time preserving the optical edges and, on
the other, low resolution LiDAR data in the form of normalized
Digital Surface Map (nDSM) is upsampled through the joint mean
shift algorithm. Experiments on both the edge-preserving smoothing
and upsampling capabilities using synthetic RGB-z data show that the
mean shift algorithm is superior to bilateral filtering as well as to
other classical smoothing and upsampling algorithms. Application of
the proposed methodology for 3D reconstruction of buildings of a
pilot region of Athens, Greece results in a significant visual
improvement of the 3D building block model.
Abstract: This paper deals with various questions related to
functionality and providing banking services in the European union
on the Internet. Due to the fact that we live in the information
technologies era, the Internet become a new space for doing
economic and business activities in all areas, and especially important
in banking. Accepting the busy tempo of life, in the past several years
electronic banking has become necessity and a must for most users of
banking services. On a sample of 300 web sites of the banks
operating in European Union (EU) we conduct the research on the
functionality of e-banking services offered through banks web sites
with the key objective to reveal to what extent the information
technologies are used in their business operations. Characteristics of
EU banks websites will be examined and compared to the basic
groups of business activities on the web. Also some
recommendations for the successful bank web sites will be provided.
Abstract: The growth in the volume of text data such as books
and articles in libraries for centuries has imposed to establish
effective mechanisms to locate them. Early techniques such as
abstraction, indexing and the use of classification categories have
marked the birth of a new field of research called "Information
Retrieval". Information Retrieval (IR) can be defined as the task of
defining models and systems whose purpose is to facilitate access to
a set of documents in electronic form (corpus) to allow a user to find
the relevant ones for him, that is to say, the contents which matches
with the information needs of the user. This paper presents a new
semantic indexing approach of a documentary corpus. The indexing
process starts first by a term weighting phase to determine the
importance of these terms in the documents. Then the use of a
thesaurus like Wordnet allows moving to the conceptual level.
Each candidate concept is evaluated by determining its level of
representation of the document, that is to say, the importance of the
concept in relation to other concepts of the document. Finally, the
semantic index is constructed by attaching to each concept of the
ontology, the documents of the corpus in which these concepts are
found.
Abstract: This study investigated the behavior of improved soft soils through the vibro replacement technique by considering their settlements and consolidation rates and the applicability of this technique in various types of soils and settlement and bearing capacity calculations.
Abstract: The effect of additional magnesium oxide (MgO) was
investigated by using the tungsten oxide supported on silica catalyst
(WOx/SiO2) physically mixed with MgO in a weight ratio 1:1. The
both fresh and spent catalysts were characterized by FT-Raman
spectrometer, UV-Vis spectrometer, X-Ray diffraction (XRD) and
temperature programmed oxidation (TPO). The results indicated that
the additional MgO could enhance the conversion of trans-2-butene
due to isomerization reaction. However, adding MgO would increase
the amount of coke deposit on the WOx/SiO2 catalyst. The TPO
profile presented two peaks when the WOx/SiO2 catalyst was
physically mixed with MgO. The further peak was suggested that
came from coke precursor could be produced by isomerization
reaction of undesired product. Then, the occurred coke precursor
could deposit and form coke on the acid catalyst.
Abstract: Pt/γ-Al2O3 membrane catalysts were prepared via an
evaporative-crystallization deposition method. The obtained Pt/γ-
Al2O3 catalyst activity was tested after characterization (SEM-EDAX
observation, BET measurement, permeability assessment) in the
catalytic oxidation of selected volatile organic compound (VOC) i.e.
propane, fed in mixture of oxygen. The VOC conversion (nearly
90%) obtained by varying the operating temperature showed that
flow-through membrane reactor might do better in the abatement of
VOCs.
Abstract: Mangosteen (Garcinia mangostana) pericarp is
considered as agricultural waste and not fully utilized in food
products. It is widely reported that mangosteen pericarp contains high
antioxidant properties. The objective of this study is to develop novel
yellow alkaline noodle (YAN) substituted with different levels of
mangosteen pericarp powder (MPP). YAN formulation was
substituted with different levels of MPP (0%, 5%, 10% and 15%).
The effect on nutritional and antioxidant properties was evaluated.
Higher substitution levels of MPP resulted in significant increase
(p
Abstract: Testamentary succession rules in the Russian
Federation have been developing intensively since the collapse of the
Soviet Union. The article analyzes specific aspects of the closed will
in Russian civil law. It discusses advantages and drawbacks of the
closed will. In addition to that, the paper focuses on the will drafting
and attestation procedures. The research provides ways to improve
and enhance Russian legislation governing the closed will.
Abstract: Roadway planning and design is a very complex
process involving five key phases before a project is completed;
planning, project development, final design, right-of-way, and
construction. The planning phase for a new roadway transportation
project is a very critical phase as it greatly affects all latter phases of
the project. A location study is usually performed during the
preliminary planning phase in a new roadway project. The objective
of the location study is to develop alignment alternatives that are cost
efficient considering land acquisition and construction costs. This
paper describes a methodology to develop optimal preliminary
roadway alignments utilizing spatial-data. Four optimization criteria
are taken into consideration; roadway length, land cost, land slope,
and environmental impacts. The basic concept of the methodology is
to convert the proposed project area into a grid, which represents the
search space for an optimal alignment. The aforementioned
optimization criteria are represented in each of the grid’s cells. A
spatial-data optimization technique is utilized to find the optimal
alignment in the search space based on the four optimization criteria.
Two case studies for new roadway projects in Duval County in the
State of Florida are presented to illustrate the methodology. The
optimization output alignments are compared to the proposed Florida
Department of Transportation (FDOT) alignments. The comparison is
based on right-of-way costs for the alignments. For both case studies,
the right-of-way costs for the developed optimal alignments were
found to be significantly lower than the FDOT alignments.
Abstract: The potential neuroprotective effect of Phyllantus
nuriri against Fe2+ and sodium nitroprusside (SNP) induced oxidative
stress in mitochondria of rats brain was evaluated. Cellular viability
was assessed by MTT reduction, reactive oxygen species (ROS)
generation was measured using the probe 2,7-dichlorofluoresce
indiacetate (DCFH-DA). Glutathione content was measured using
dithionitrobenzoic acid (DTNB). Fe2+ (10μM) and SNP (5μM)
significantly decreased mitochondrial activity, assessed by MTT
reduction assay, in a dose-dependent manner, this occurred in parallel
with increased glutathione oxidation, ROS production and lipid
peroxidation end-products (thiobarbituric acid reactive substances,
TBARS). The co-incubation with methanolic extract of Phyllantus
nuriri (10-200 μg/ml) reduced the disruption of mitochondrial
activity, gluthathione oxidation, ROS production as well as the
increase in TBARS levels caused by both Fe2+ and SNP in a dose
dependent manner. HPLC analysis of the extract revealed the
presence of gallic acid (20.540.01), caffeic acid (7.930.02), rutin
(25.310.05), quercetin (31.280.03) and kaemferol (14.360.01).
This result suggests that these phytochemicals account for the
protective actions of P. niruri against Fe2+ and SNP -induced
oxidative stress. Our results show that P. nuriri consist important
bioactive molecules in the search for an improved therapy against the
deleterious effects of Fe2+, an intrinsic producer of reactive oxygen
species (ROS), that leads to neuronal oxidative stress and
neurodegeneration.
Abstract: One of the main challenges in using the Discrete
Element Method (DEM) is to specify the correct input parameter
values. In general, the models are sensitive to the input parameter
values and accurate results can only be achieved if the correct values
are specified. For the linear contact model, micro-parameters such as
the particle density, stiffness, coefficient of friction, as well as the
particle size and shape distributions are required. There is a need for
a procedure to accurately calibrate these parameters before any
attempt can be made to accurately model a complete bulk materials
handling system. Since DEM is often used to model applications in
the mining and quarrying industries, a calibration procedure was
developed for materials that consist of relatively large (up to 40 mm
in size) particles. A coarse crushed aggregate was used as the test
material. Using a specially designed large shear box with a diameter
of 590 mm, the confined Young’s modulus (bulk stiffness) and
internal friction angle of the material were measured by means of the
confined compression test and the direct shear test respectively. DEM
models of the experimental setup were developed and the input
parameter values were varied iteratively until a close correlation
between the experimental and numerical results was achieved. The
calibration process was validated by modelling the pull-out of an
anchor from a bed of material. The model results compared well with
experimental measurement.