Abstract: The roll center is one of the key parameters for designing a suspension. Several driving characteristics are affected significantly by the migration of the roll center during the suspension-s motion. The strut/SLA (strut/short-long-arm) suspension, which is widely used in production cars, combines the space-saving characteristics of a MacPherson strut suspension with some of the preferred handling characteristics of an SLA suspension. In this study, a front strut/SLA suspension is modeled by ADAMS/Car software. Kinematic roll analysis is then employed to investigate how the rolling characteristics change under the wheel travel and steering input. The related parameters, including the roll center height, roll camber gain, toe change, scrub radius and wheel track width change, are analyzed and discussed. It is found that the strut/SLA suspension clearly has a higher roll center than strut and SLA suspensions do. The variations in the roll center height under roll analysis are very different as the wheel travel displacement and steering angle are added. The results of the roll camber gain, scrub radius and wheel track width change are considered satisfactory. However, the toe change is too large and needs fine-tuning through a sensitivity analysis.
Abstract: Large full frequency band gaps of surface and bulk
acoustic waves in two-dimensional phononic band structures with
hollow cylinders are addressed in this paper. It is well-known that
absolute frequency band gaps are difficultly obtained in a band
structure consisted of low-acoustic-impedance cylinders in
high-acoustic-impedance host materials such as PMMA/Ni band
structures. Phononic band structures with hollow cylinders are
analyzed and discussed to obtain large full frequency band gaps not
only for bulk modes but also for surface modes. The tendency of
absolute frequency band gaps of surface and bulk acoustic waves is
also addressed by changing the inner radius of hollow cylinders in this
paper. The technique and this kind of band structure are useful for
tuning the frequency band gaps and the design of acoustic waveguides.
Abstract: In this paper, the deformation modes of a compact impact absorption member subjected to axial compression are investigated using finite element method and experiments. A multiple combination compact impact absorption member, referred to as a 'compress-expand member', is proposed to substitute the conventional thin-walled circular tube. This study found that the proposed compact impact absorption member has stable load increase characteristics and a wider range of high load efficiency (Pave/Pmax) than the thin-walled circular tube. Moreover, the proposed compact impact absorption member can absorb larger loads in a smaller radius than the thin-walled cylindrical tube, as it can maintain its stable deformation in increased wall thicknesses.
Abstract: Equal Channel Angular Pressing (ECAP) is currently
being widely investigated because of its potential to produce ultrafine
grained microstructures in metals and alloys. A sound
knowledge of the plastic deformation and strain distribution is
necessary for understanding the relationships between strain
inhomogeneity and die geometry. Considerable research has been
reported on finite element analysis of this process, assuming threedimensional
plane strain condition. However, the two-dimensional
models are not suitable due to the geometry of the dies, especially in
cylindrical ones. In the present work, three-dimensional simulation of
ECAP process was carried out for six outer corner radii (sharp to 10
mm in steps of 2 mm), with channel angle 105¶Çü▒, for strain hardening
aluminium alloy (AA 6101) using ABAQUS/Standard software.
Strain inhomogeneity is presented and discussed for all cases. Pattern
of strain variation along selected radial lines in the body of the workpiece
is presented. It is found from the results that the outer corner
has a significant influence on the strain distribution in the body of
work-piece. Based on inhomogeneity and average strain criteria,
there is an optimum outer corner radius.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: In practice, wireless networks has the property that
the signal strength attenuates with respect to the distance from the
base station, it could be better if the nodes at two hop away are
considered for better quality of service. In this paper, we propose a
procedure to identify delay preserving substructures for a given
wireless ad-hoc network using a new graph operation G 2 – E (G) =
G* (Edge difference of square graph of a given graph and the
original graph). This operation helps to analyze some induced
substructures, which preserve delay in communication among them.
This operation G* on a given graph will induce a graph, in which 1-
hop neighbors of any node are at 2-hop distance in the original
network. In this paper, we also identify some delay preserving
substructures in G*, which are (i) set of all nodes, which are mutually
at 2-hop distance in G that will form a clique in G*, (ii) set of nodes
which forms an odd cycle C2k+1 in G, will form an odd cycle in G*
and the set of nodes which form a even cycle C2k in G that will form
two disjoint companion cycles ( of same parity odd/even) of length k
in G*, (iii) every path of length 2k+1 or 2k in G will induce two
disjoint paths of length k in G*, and (iv) set of nodes in G*, which
induces a maximal connected sub graph with radius 1 (which
identifies a substructure with radius equal 2 and diameter at most 4 in
G). The above delay preserving sub structures will behave as good
clusters in the original network.
Abstract: Radio wave propagation on the road surface is a major
problem on wireless sensor network for traffic monitoring. In this
paper, we compare receiving signal strength on two scenarios 1) an
empty road and 2) a road with a vehicle. We investigate the effect of
antenna polarization and antenna height to the receiving signal
strength. The transmitting antenna is installed on the road surface.
The receiving signal is measured 360 degrees around the transmitting
antenna with the radius of 2.5 meters. Measurement results show the
receiving signal fluctuation around the transmitting antenna in both
scenarios. Receiving signal with vertical polarization antenna results
in higher signal strength than horizontal polarization antenna. The
optimum antenna elevation is 1 meter for both horizon and vertical
polarizations with the vehicle on the road. In the empty road, the
receiving signal level is unvarying with the elevation when the
elevation is greater than 1.5 meters.
Abstract: Let G be a graph of order n. The second stage adjacency matrix of G is the symmetric n × n matrix for which the ijth entry is 1 if the vertices vi and vj are of distance two; otherwise 0. The sum of the absolute values of this second stage adjacency matrix is called the second stage energy of G. In this paper we investigate a few properties and determine some upper bounds for the largest eigenvalue.
Abstract: The possibility of radionuclides-related contamination
of lands at agricultural holdings defines the necessity to apply special
protective measures in plant growing. The aim of researches is to
elucidate the influence of polymers applying on biological migration
of man-made anthropogenic radionuclides 90Sr and 137Cs in the
system water - soil – plant. The tests are being carried out under field
conditions with and without application of polymers in root-inhabited
media in more radioecological tension zone (with the radius of 7 km
from the Armenian Nuclear Power Plant). The polymers on the base
of K+, Caµ, KµCaµ ions were tested. Productivity of pepper
depending on the presence and type of polymer material, content of
artificial radionuclides in waters, soil and plant material has been
determined. The character of different polymers influence on the
artificial radionuclides migration and accumulation in the system
water-soil-plant and accumulation in the plants has been cleared up.
Abstract: Position based routing protocols are the kinds of
routing protocols, which they use of nodes location information,
instead of links information to routing. In position based routing
protocols, it supposed that the packet source node has position
information of itself and it's neighbors and packet destination node.
Greedy is a very important position based routing protocol. In one of
it's kinds, named MFR (Most Forward Within Radius), source node
or packet forwarder node, sends packet to one of it's neighbors with
most forward progress towards destination node (closest neighbor to
destination). Using distance deciding metric in Greedy to forward
packet to a neighbor node, is not suitable for all conditions. If closest
neighbor to destination node, has high speed, in comparison with
source node or intermediate packet forwarder node speed or has very
low remained battery power, then packet loss probability is
increased. Proposed strategy uses combination of metrics distancevelocity
similarity-power, to deciding about giving the packet to
which neighbor. Simulation results show that the proposed strategy
has lower lost packets average than Greedy, so it has more reliability.
Abstract: The nature of wireless ad hoc and sensor networks
make them very attractive to attackers. One of the most popular and
serious attacks in wireless ad hoc networks is wormhole attack and
most proposed protocols to defend against this attack used
positioning devices, synchronized clocks, or directional antennas.
This paper analyzes the nature of wormhole attack and existing
methods of defending mechanism and then proposes round trip time
(RTT) and neighbor numbers based wormhole detection mechanism.
The consideration of proposed mechanism is the RTT between two
successive nodes and those nodes- neighbor number which is needed
to compare those values of other successive nodes. The identification
of wormhole attacks is based on the two faces. The first consideration
is that the transmission time between two wormhole attack affected
nodes is considerable higher than that between two normal neighbor
nodes. The second detection mechanism is based on the fact that by
introducing new links into the network, the adversary increases the
number of neighbors of the nodes within its radius. This system does
not require any specific hardware, has good performance and little
overhead and also does not consume extra energy. The proposed
system is designed in ad hoc on-demand distance vector (AODV)
routing protocol and analysis and simulations of the proposed system
are performed in network simulator (ns-2).
Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: The influence of axial magnetic field (B=0.48 T) on
the variation of ionization efficiency coefficient h and secondary
electron emission coefficient g with respect to reduced electric field
E/P is studied at a new range of plane-parallel electrode spacing (0<
d< 20 cm) and different nitrogen working pressure between 0.5-20
Pa. The axial magnetic field is produced from an inductive copper
coil of radius 5.6 cm. The experimental data of breakdown voltage is
adopted to estimate the mean Paschen curves at different working
features. The secondary electron emission coefficient is calculated
from the mean Paschen curve and used to determine the minimum
breakdown voltage. A reduction of discharge voltage of about 25% is
investigated by the applied of axial magnetic field. At high interelectrode
spacing, the effect of axial magnetic field becomes more
significant for the obtained values of h but it was less for the values
of g.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: This paper presents an advance in monitoring and
process control of surface roughness in CNC machine for the turning
and milling processes. An integration of the in-process monitoring
and process control of the surface roughness is proposed and
developed during the machining process by using the cutting force
ratio. The previously developed surface roughness models for turning
and milling processes of the author are adopted to predict the inprocess
surface roughness, which consist of the cutting speed, the
feed rate, the tool nose radius, the depth of cut, the rake angle, and
the cutting force ratio. The cutting force ratios obtained from the
turning and the milling are utilized to estimate the in-process surface
roughness. The dynamometers are installed on the tool turret of CNC
turning machine and the table of 5-axis machining center to monitor
the cutting forces. The in-process control of the surface roughness
has been developed and proposed to control the predicted surface
roughness. It has been proved by the cutting tests that the proposed
integration system of the in-process monitoring and the process
control can be used to check the surface roughness during the cutting
by utilizing the cutting force ratio.
Abstract: Iron oxide nanoparticle was synthesized by reactive-precipitation method followed by high speed centrifuge and phase transfer in order to stabilized nanoparticles in the solvent. Particle size of SPIO was 8.2 nm by SEM, and the hydraulic radius was 17.5 nm by dynamic light scattering method. Coercivity and saturated magnetism were determined by VSM (vibrating sample magnetometer), coercivity of nanoparticle was lower than 10 Hc, and the saturated magnetism was higher than 65 emu/g. Stabilized SPIO was then transferred to aqueous phase by reacted with excess amount of poly (ethylene glycol) (PEG) silane. After filtration and dialysis, the SPIO T2 contrast agent was ready to use. The hydraulic radius of final product was about 70~100 nm, the relaxation rates R2 (1/T2) measured by magnetic resonance imaging (MRI) was larger than 200(sec-1).
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a three-bladed
small vertical axis Darrieus wind turbine depending on blade chord
curvature with respect to rotor axis.
The adopted survey methodology is based on an analytical code
coupled to a solid modeling software, capable of generating the
desired blade geometry depending on the blade design geometric
parameters, which is linked to a finite volume CFD code for the
calculation of rotor performance.
After describing and validating the model with experimental data,
the results of numerical simulations are proposed on the bases of two
different blade profile architectures, which are respectively
characterized by a straight chord and by a curved one, having a chord
radius equal to rotor external circumference. A CFD campaign of
analysis is completed for three blade-candidate airfoil sections, that is
the recently-developed DU 06-W-200 cambered blade profile, a
classical symmetrical NACA 0021 and its derived cambered airfoil,
characterized by a curved chord, having a chord radius equal to rotor
external circumference.
The effects of blade chord curvature on angle of attack, blade
tangential and normal forces are first investigated and then the
overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of blade camber on overall rotor performance.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: In this paper dynamics of a vapour bubble generated
due to a local energy input inside a vertical rigid cylinder and in the
absence of buoyancy forces is investigated. Different ratios of the
diameter of the rigid cylinder to the maximum radius of the bubble
are considered. The Boundary Integral Equation Method is employed
for numerical simulation of the problem. Results show that during
the collapse phase of the bubble inside a vertical rigid cylinder, two
liquid micro jets are developed on the top and bottom sides of the
vapour bubble and are directed inward. Results also show that
existence of a deposit rib inside the vertical rigid cylinder slightly
increases the life time of the bubble. It is found that by increasing the
ratio of the cylinder diameter to the maximum radius of the bubble,
the rate of the growth and collapse phases of the bubble increases
and the life time of the bubble decreases.
Abstract: The parametrical study of Shrouded Contra-rotating
Rotor was done in this paper based on 2D axisymmetric simulations.
The calculations were made with an actuator disk as double rotor
model. It objects to explore and quantify the effects of different shroud
geometry parameters mainly using the performance of power loading
(PL), which could evaluate the whole propulsion system capability as
5 Newtontotal thrust generationfor hover demand. The numerical
results show that:The increase of nozzle radius is desired but limited
by the flow separation, its optimal design is around 1.15 times rotor
radius, the viscosity effects greatly constraint the influence of nozzle
shape, the divergent angle around 10.5° performs best for chosen
nozzle length;The parameters of inlet such as leading edge curvature,
radius and internal shape do not affect thrust great but play an
important role in pressure distribution which could produce most part
of shroud thrust, they should be chosen according to the reduction of
adverse pressure gradients to reduce the risk of boundary separation.