Abstract: The pullout strength had an effect on the stability of
plate screw fixation when inserted in the cervical spine. Nine
different titanium alloy bone screws were used to test the pullout
strength through finite element analysis. The result showed that the
Moss Miami I can bear the highest pullout force at 1,075 N, which
causes the maximum von Mises stress at 858.87 MPa, a value over
the yield strength of titanium. The bone screw should have large
outer diameter, core diameter and proximal root radius to increase the
pullout strength.
Abstract: This paper presents the details of a numerical study of
buckling and post buckling behaviour of laminated carbon fiber
reinforced plastic (CFRP) thin-walled cylindrical shell under axial
compression using asymmetric meshing technique (AMT) by
ABAQUS. AMT is considered to be a new perturbation method to
introduce disturbance without changing geometry, boundary
conditions or loading conditions. Asymmetric meshing affects both
predicted buckling load and buckling mode shapes. Cylindrical shell
having lay-up orientation [0^o/+45^o/-45^o/0^o] with radius to thickness
ratio (R/t) equal to 265 and length to radius ratio (L/R) equal to 1.5 is
analysed numerically. A series of numerical simulations
(experiments) are carried out with symmetric and asymmetric
meshing to study the effect of asymmetric meshing on predicted
buckling behaviour. Asymmetric meshing technique is employed in
both axial direction and circumferential direction separately using
two different methods, first by changing the shell element size and
varying the total number elements, and second by varying the shell
element size and keeping total number of elements constant. The
results of linear analysis (Eigenvalue analysis) and non-linear
analysis (Riks analysis) using symmetric meshing agree well with
analytical results. The results of numerical analysis are presented in
form of non-dimensional load factor, which is the ratio of buckling
load using asymmetric meshing technique to buckling load using
symmetric meshing technique. Using AMT, load factor has about 2%
variation for linear eigenvalue analysis and about 2% variation for
non-linear Riks analysis. The behaviour of load end-shortening curve
for pre-buckling is same for both symmetric and asymmetric meshing
but for asymmetric meshing curve behaviour in post-buckling
becomes extraordinarily complex. The major conclusions are:
different methods of AMT have small influence on predicted
buckling load and significant influence on load displacement curve
behaviour in post buckling; AMT in axial direction and AMT in
circumferential direction have different influence on buckling load
and load displacement curve in post-buckling.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: We have developed a new computer program in
Fortran 90, in order to obtain numerical solutions of a system
of Relativistic Magnetohydrodynamics partial differential equations
with predetermined gravitation (GRMHD), capable of simulating
the formation of relativistic jets from the accretion disk of matter
up to his ejection. Initially we carried out a study on numerical
methods of unidimensional Finite Volume, namely Lax-Friedrichs,
Lax-Wendroff, Nessyahu-Tadmor method and Godunov methods
dependent on Riemann problems, applied to equations Euler in
order to verify their main features and make comparisons among
those methods. It was then implemented the method of Finite
Volume Centered of Nessyahu-Tadmor, a numerical schemes that
has a formulation free and without dimensional separation of
Riemann problem solvers, even in two or more spatial dimensions,
at this point, already applied in equations GRMHD. Finally, the
Nessyahu-Tadmor method was possible to obtain stable numerical
solutions - without spurious oscillations or excessive dissipation -
from the magnetized accretion disk process in rotation with respect
to a central black hole (BH) Schwarzschild and immersed in a
magnetosphere, for the ejection of matter in the form of jet over a
distance of fourteen times the radius of the BH, a record in terms
of astrophysical simulation of this kind. Also in our simulations,
we managed to get substructures jets. A great advantage obtained
was that, with the our code, we got simulate GRMHD equations in
a simple personal computer.
Abstract: In this study the instability problem of a modified
Taylor-Couette flow between two vertical coaxial cylinders of radius
R1, R2 is considered. The modification is based on the wavy shape of
the inner cylinder surface, where inner cylinders with different
surface amplitude and wavelength are used. The study aims to
discover the effect of the inner surface geometry on the instability
phenomenon that undergoes Taylor-Couette flow. The study reveals
that the transition processes depends strongly on the amplitude and
wavelength of the inner cylinder surface and resulting in flow
instabilities that are strongly different from that encountered in the
case of the classical Taylor-Couette flow.
Abstract: We present a trigonometric scheme to approximate a
circular arc with its two end points and two end tangents/unit
tangents. A rational cubic trigonometric Bézier curve is constructed
whose end control points are defined by the end points of the circular
arc. Weight functions and the remaining control points of the cubic
trigonometric Bézier curve are estimated by variational approach to
reproduce a circular arc. The radius error is calculated and found less
than the existing techniques.
Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.
Abstract: This paper presents the application of the Discrete
Component Model for heating and evaporation to multi-component
biodiesel fuel droplets in direct injection internal combustion engines.
This model takes into account the effects of temperature gradient,
recirculation and species diffusion inside droplets. A distinctive
feature of the model used in the analysis is that it is based on the
analytical solutions to the temperature and species diffusion
equations inside the droplets. Nineteen types of biodiesel fuels are
considered. It is shown that a simplistic model, based on the
approximation of biodiesel fuel by a single component or ignoring
the diffusion of components of biodiesel fuel, leads to noticeable
errors in predicted droplet evaporation time and time evolution of
droplet surface temperature and radius.
Abstract: This paper evaluates the performance of a multi-lane
four legged modern roundabout operating in Muscat using SIDRA
model. The performance measures include Degree of Saturation
(DOS), average delay, and queue lengths. The geometric and traffic
data were used for model preparation. Gap acceptance parameters,
critical gap and follow up headway, were used for calibration of
SIDRA model. The results from the analysis showed that currently
the roundabout is experiencing delays up to 610 seconds per vehicle
with DOS 1.67 during peak hour. Further, sensitivity analysis for
general and roundabout parameters was performed, amongst lane
width, cruise speed, inscribed diameter, entry radius and entry angle
showed that inscribed diameter is most crucial factor affecting delay
and DOS. Up gradation of roundabout to fully signalized junction
was found as the suitable solution which will serve for future years
with LOS C for design year having DOS of 0.9 with average control
delay of 51.9 seconds per vehicle.
Abstract: From an organizational perspective, leaders are a
variation of the same talent pool in that they all score a larger than
average value on the bell curve that maps leadership behaviors and
characteristics, namely competence, vision, communication,
confidence, cultural sensibility, stewardship, empowerment,
authenticity, reinforcement, and creativity. The question that remains
unanswered and essentially unresolved is how to explain the irony
that leaders are so much alike yet their organizations diverge so
noticeably in their ability to innovate. Leadership intersects with
innovation at the point where human interactions get exceedingly
complex and where certain paradoxical forces cohabit: conflict with
conciliation, sovereignty with interdependence, and imagination with
realism. Rather than accepting that leadership is without context, we
argue that leaders are specialists of their domain and that those
effective at leading for innovation are distinct within the broader pool
of leaders. Keeping in view the extensive literature on leadership and
innovation, we carried out a quantitative study with data collected
over a five-year period involving 240 participants from across five
dissimilar companies based in the United States. We found that while
innovation and leadership are, in general, strongly interrelated (r =
.89, p = 0.0), there are five qualities that set leaders apart on
innovation. These qualities include a large radius of trust, a restless
curiosity with a low need for acceptance, an honest sense of self and
other, a sense for knowledge and creativity as the yin and yang of
innovation, and an ability to use multiple senses in the engagement
with followers. When these particular behaviors and characteristics
are present in leaders, organizations out-innovate their rivals by a
margin of 29.3 per cent to gain an unassailable edge in a business
environment that is regularly disruptive. A strategic outcome of this
study is a psychometric scale named iLeadership, proposed with the
underlying evidence, limitations, and potential for leadership and
innovation in organizations.c
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: Ultrasonic shot peening (USP) on AALY12 sheet was studied. Several parameters (arc heights, surface roughness, surface topography and micro hardness) with different USP process parameters were measured. The research proposes that radius of curvature of shot peened sheet increases with time and electric current decreasing, while increases with pin diameter increasing, and radius of curvature reaches a saturation level after a specific processing time and electric current. An empirical model of the relationship between radius of curvature and pin diameter, electric current, time was also obtained. The research shows that the increment of surface and vertical micro hardness of material is more obvious with longer time and higher value of electric current, which can be up to 20% and 28% respectively.
Abstract: The design of multi stage deep drawing processes requires the evaluation of many process parameters such as the intermediate die geometry, the blank shape, the sheet thickness, the blank holder force, friction, lubrication etc..These process parameters have to be determined for the optimum forming conditions before the process design. In general sheet metal forming may involve stretching drawing or various combinations of these basic modes of deformation. It is important to determine the influence of the process variables in the design of sheet metal working process. Especially, the punch and die corner for deep drawing will affect the formability. At the same time the prediction of sheet metals springback after deep drawing is an important issue to solve for the control of manufacturing processes. Nowadays, the importance of this problem increases because of the use of steel sheeting with high stress and also aluminum alloys.
The aim of this paper is to give a better understanding of the springback and its effect in various sheet metals forming process such as expansion and restreint deep drawing in the cup drawing process, by varying radius die, lubricant for two commercially available materials e.g. galvanized steel and Aluminum sheet. To achieve these goals experiments were carried out and compared with other results. The original of our purpose consist on tests which are ensured by adapting a U-type stretching-bending device on a tensile testing machine, where we studied and quantified the variation of the springback.
Abstract: Coverage and capacity performance in a cellular network determines the system potentials. If the coverage radius is limited, end users suffer poor service quality, if the system capacity reduces, fewer subscribers will be accommodated. This paper investigated the performance effects of the noise rise caused by the spurious emission from a co-located jammer involving downlink frequency of CDMA2000 and uplink frequency of WCDMA operating at 1.9GHz. Measurements were carried out to evaluate the impact on the coverage radius and the system capacity.
Abstract: Noise removal techniques play a vital role in the performance of electrocardiographic (ECG) signal processing systems. ECG signals can be corrupted by various kinds of noise such as baseline wander noise, electromyographic interference, and powerline interference. One of the significant challenges in ECG signal processing is the degradation caused by additive 50 or 60 Hz powerline interference. This work investigates the removal of power line interference and suppression of transient response for filtering noise corrupted ECG signals. We demonstrate the effectiveness of infinite impulse response (IIR) notch filter with time varying pole radius for improving the transient behavior. The temporary change in the pole radius of the filter diminishes the transient behavior. Simulation results show that the proposed IIR filter with time varying pole radius outperforms traditional IIR notch filters in terms of mean square error and transient suppression.
Abstract: The basic ability of a vehicle is to “run”, “turn” and “stop”. The safeness and comfort during a drive on various road surfaces and speed depends on the performance of these basic abilities of the vehicle. Stability and maneuverability of a vehicle are vital in automotive engineering. The stability of a vehicle is the ability of the vehicle to revert back to a stable state during a drive when faced with crosswinds and irregular road conditions. Maneuverability of a vehicle is the ability of the vehicle to change direction during a drive swiftly based on the steering of the driver. The stability and maneuverability of a vehicle can also be defined as the driving stability of the vehicle. Since the fossil fueled vehicle is the main type of transportation today, the environmental factor in automotive engineering is also vital. By improving the fuel efficiency of the vehicle, the overall carbon emission will be reduced, thus reducing the effect of global warming and greenhouse gas on the Earth. Another main focus of the automotive engineering is the safety performance of the vehicle, especially with the worrying increase of vehicle collision every day. With better safety performance of a vehicle, every driver will be more confident driving every day. Next, let us focus on the “turn” ability of a vehicle. By improving this particular ability of the vehicle, the cornering limit of the vehicle can be improved, thus increasing the stability and maneuverability factor. In order to improve the cornering limit of the vehicle, a study to find the balance between the steering systems, the stability of the vehicle, higher lateral acceleration and the cornering limit detection must be conducted. The aim of this research is to study and develop a new suspension system that will boost the lateral acceleration of the vehicle and ultimately improving the cornering limit of the vehicle. This research will also study environmental factor and the stability factor of the new suspension system. The double wishbone suspension system is widely used in a four-wheel vehicle, especially for high cornering performance sports car and racing car. The double wishbone designs allow the engineer to carefully control the motion of the wheel by controlling such parameters as camber angle, caster angle, toe pattern, roll center height, scrub radius, scuff, and more. The development of the new suspension system will focus on the ability of the new suspension system to optimize the camber control and to improve the camber limit during a cornering motion. The research will be carried out using the CAE analysis tool. Using this analysis tool we will develop a JSAE Formula Machine equipped with the double wishbone system and also the new suspension system and conduct simulation and conduct studies on the performance of both suspension systems.
Abstract: The propulsion of a bacterial flagellum in a viscous fluid has attracted many interests in the field of biological hydrodynamics, but remains yet fully understood and thus still a challenging problem. In this study, therefore, we have numerically investigated the flow around a steadily rotating micro-sized spring to further understand such bacterial flagellum propulsion. Note that a bacterium gains thrust (propulsive force) by rotating the flagellum connected to the body through a bio motor to move forward. For the investigation, we convert the spring model from the micro scale to the macro scale using a similitude law (scale law) and perform simulations on the converted macro-scale model using a commercial software package, CFX v13 (ANSYS). To scrutinize the propulsion characteristics of the flagellum through the simulations, we make parameter studies by changing some flow parameters, such as the pitch, helical radius and rotational speed of the spring and the Reynolds number (or fluid viscosity), expected to affect the thrust force experienced by the rotating spring. Results show that the propulsion characteristics depend strongly on the parameters mentioned above. It is observed that the forward thrust increases in a linear fashion with either of the rotational speed or the fluid viscosity. In addition, the thrust is directly proportional to square of the helical radius and but the thrust force is increased and then decreased based on the peak value to the pitch. Finally, we also present the appropriate flow and pressure fields visualized to support the observations.
Abstract: In this study, thermo elastic stress analysis is performed on a cylinder made of laminated isotropic materials under thermomechanical loads. Laminated cylinders have many applications such as aerospace, automotive and nuclear plant in the
industry. These cylinders generally performed under thermomechanical loads. Stress and displacement distribution of the laminated cylinders are determined using by analytical method both thermal and mechanical loads. Based on the results, materials combination plays an important role on the stresses distribution along the radius. Variation of the stresses and displacements along the radius are presented as graphs. Calculations program are prepared using MATLAB® by authors.
Abstract: A supersonic expansion cannot be achieved within a convergent-divergent nozzle if the flow velocity does not reach that of the sound at the throat. The computation of the flow field characteristics at the throat is thus essential to the nozzle developed thrust value and therefore to the aircraft or rocket it propels. Several approaches were developed in order to describe the transonic expansion, which takes place through the throat of a De-Laval convergent-divergent nozzle. They all allow reaching good results but showing a major shortcoming represented by their inability to describe the transonic flow field for nozzles having a small throat radius. The approach initially developed by Kliegel & Levine uses the velocity series development in terms of the normalized throat radius added to unity instead of solely the normalized throat radius or the traditional small disturbances theory approach. The present investigation carries out the application of these three approaches for different throat radiuses of curvature. The method using the normalized throat radius added to unity shows better results when applied to geometries integrating small throat radiuses.
Abstract: An experimental study has been done to investigate the flame acceleration in a closed pipe. A horizontal steel pipe, 2m long and 0.1m in diameter (L/D of 20), was used in this work. For tests with 90 degree bends, the bend had a radius of 0.1m and thus, the pipe was lengthened 1m (based on the centreline length of the segment). Ignition was affected at one end of the vessel while the other end was closed. Only stoichiometric concentration (Ф, = 1.0) of natural gas/air mixtures will be reported in this paper. It was demonstrated that bend pipe configuration gave three times higher in maximum overpressure (5.5 bars) compared to straight pipe (2.0 bars). From the results, the highest flame speed, of 63ms-1, was observed in a gas explosion with bent pipe; greater by a factor of ~3 as compared with straight pipe (23ms-1). This occurs because bending acts similar to an obstacle, in which this mechanism can induce more turbulence, initiating combustion in an unburned pocket at the corner region and causing a high mass burning rate, which increases the flame speed.