Abstract: Particles exhausted from cars have adverse impacts on
human health. The study developed a three-dimensional particle
dispersion numerical model including particle coagulation to simulate
the particle concentration distribution under idling conditions in a
residential underground garage. The simulation results demonstrate
that particle disperses much faster in the vertical direction than that in
horizontal direction. The enhancement of particle dispersion in the
vertical direction due to the increase of cars with engine running is
much stronger than that in the car exhaust direction. Particle dispersion
from each pair of adjacent cars has little influence on each other in the
study. Average particle concentration after 120 seconds exhaust is
1.8-4.5 times higher than the initial total particles at ambient
environment. Particle pollution in the residential underground garage
is severe.
Abstract: The thermal conductivity of a fluid can be
significantly enhanced by dispersing nano-sized particles in it, and
the resultant fluid is termed as "nanofluid". A theoretical model for
estimating the thermal conductivity of a nanofluid has been proposed
here. It is based on the mechanism that evenly dispersed
nanoparticles within a nanofluid undergo Brownian motion in course
of which the nanoparticles repeatedly collide with the heat source.
During each collision a rapid heat transfer occurs owing to the solidsolid
contact. Molecular dynamics (MD) simulation of the collision
of nanoparticles with the heat source has shown that there is a pulselike
pick up of heat by the nanoparticles within 20-100 ps, the extent
of which depends not only on thermal conductivity of the
nanoparticles, but also on the elastic and other physical properties of
the nanoparticle. After the collision the nanoparticles undergo
Brownian motion in the base fluid and release the excess heat to the
surrounding base fluid within 2-10 ms. The Brownian motion and
associated temperature variation of the nanoparticles have been
modeled by stochastic analysis. Repeated occurrence of these events
by the suspended nanoparticles significantly contributes to the
characteristic thermal conductivity of the nanofluids, which has been
estimated by the present model for a ethylene glycol based nanofluid
containing Cu-nanoparticles of size ranging from 8 to 20 nm, with
Gaussian size distribution. The prediction of the present model has
shown a reasonable agreement with the experimental data available
in literature.
Abstract: The purpose of this study was to reduce patient
waiting times, improve system throughput and improve resources
utilization in radiology department. A discrete event simulation
model was developed using Arena simulation software to investigate
different alternatives to improve the overall system delivery based on
adding resource scenarios due to the linkage between patient waiting
times and resource availability. The study revealed that there is no
addition investment need to procure additional scanner but hospital
management deploy managerial tactics to enhance machine
utilization and reduce the long waiting time in the department.
Abstract: Many wireless sensor network applications require
K-coverage of the monitored area. In this paper, we propose a
scalable harmony search based algorithm in terms of execution
time, K-Coverage Enhancement Algorithm (KCEA), it attempts to
enhance initial coverage, and achieve the required K-coverage degree
for a specific application efficiently. Simulation results show that
the proposed algorithm achieves coverage improvement of 5.34%
compared to K-Coverage Rate Deployment (K-CRD), which achieves
1.31% when deploying one additional sensor. Moreover, the proposed
algorithm is more time efficient.
Abstract: Cross flow water tube heat exchanger can be designed
and made operational using methods of model building and
simulation of the system. This paper projects the design and
development of a model of cross flow water tube heat-exchanger
system, simulation and validation of control analysis of different
tuning methods. Feedback and override control system is developed
using inputs acquired with the help of sensory system. A
mathematical model is formulated for analysis of system behaviour.
The temperature is regulated at the desired set point automatically.
Abstract: Nowadays, Photovoltaic-PV Farms/ Parks and large
PV-Smart Grid Interface Schemes are emerging and commonly
utilized in Renewable Energy distributed generation. However, PVhybrid-
Dc-Ac Schemes using interface power electronic converters
usually has negative impact on power quality and stabilization of
modern electrical network under load excursions and network fault
conditions in smart grid. Consequently, robust FACTS based
interface schemes are required to ensure efficient energy utilization
and stabilization of bus voltages as well as limiting switching/fault
onrush current condition. FACTS devices are also used in smart grid-
Battery Interface and Storage Schemes with PV-Battery Storage
hybrid systems as an elegant alternative to renewable energy
utilization with backup battery storage for electric utility energy and
demand side management to provide needed energy and power
capacity under heavy load conditions. The paper presents a robust
interface PV-Li-Ion Battery Storage Interface Scheme for
Distribution/Utilization Low Voltage Interface using FACTS
stabilization enhancement and dynamic maximum PV power tracking
controllers.
Digital simulation and validation of the proposed scheme is done
using MATLAB/Simulink software environment for Low Voltage-
Distribution/Utilization system feeding a hybrid Linear-Motorized
inrush and nonlinear type loads from a DC-AC Interface VSC-6-
pulse Inverter Fed from the PV Park/Farm with a back-up Li-Ion
Storage Battery.
Abstract: Container handling problems at container terminals
are NP-hard problems. This paper presents an approach using
discrete-event simulation modeling to optimize solution for storage
space allocation problem, taking into account all various interrelated
container terminal handling activities. The proposed approach is
applied on a real case study data of container terminal at Alexandria
port. The computational results show the effectiveness of the
proposed model for optimization of storage space allocation in
container terminal where 54% reduction in containers handling time
in port is achieved.
Abstract: In this paper a new design of a broadband microwave
power limiter is presented and validated into simulation by using
ADS software (Advanced Design System) from Agilent technologies.
The final circuit is built on microstrip lines by using identical Zero
Bias Schottky diodes. The power limiter is designed by Associating 3
stages Schottky diodes. The obtained simulation results permit to
validate this circuit with a threshold input power level of 0 dBm until
a maximum input power of 30 dBm.
Abstract: The IEEE 802.22 working group aims to drive the
Digital Video Broadcasting-Terrestrial (DVB-T) bands for data
communication to the rural area without interfering the TV broadcast.
In this paper, we arrive at a closed-form expression for average
detection probability of Fusion center (FC) with multiple antenna
over the κ − μ fading channel model. We consider a centralized
cooperative multiple antenna network for reporting. The DVB-T
samples forwarded by the secondary user (SU) were combined using
Maximum ratio combiner at FC, an energy detection is performed
to make the decision. The fading effects of the channel degrades
the detection probability of the FC, a generalized independent and
identically distributed (IID) κ − μ and an additive white Gaussian
noise (AWGN) channel is considered for reporting and sensing
respectively. The proposed system performance is verified through
simulation results.
Abstract: Securing the confidential data transferred via wireless
network remains a challenging problem. It is paramount to ensure
that data are accessible only by the legitimate users rather than by the
attackers. One of the most serious threats to organization is jamming,
which disrupts the communication between any two pairs of nodes.
Therefore, designing an attack-defending scheme without any packet
loss in data transmission is an important challenge. In this paper,
Dependence based Malicious Route Defending DMRD Scheme has
been proposed in multi path routing environment to prevent jamming
attack. The key idea is to defend the malicious route to ensure
perspicuous transmission. This scheme develops a two layered
architecture and it operates in two different steps. In the first step,
possible routes are captured and their agent dependence values are
marked using triple agents. In the second step, the dependence values
are compared by performing comparator filtering to detect malicious
route as well as to identify a reliable route for secured data
transmission. By simulation studies, it is observed that the proposed
scheme significantly identifies malicious route by attaining lower
delay time and route discovery time; it also achieves higher
throughput.
Abstract: Femtocells are regarded as a milestone for next
generation cellular networks. As femtocells are deployed in an
unplanned manner, there is a chance of assigning same resource to
neighboring femtocells. This scenario may induce co-channel
interference and may seriously affect the service quality of
neighboring femtocells. In addition, the dominant transmit power of a
femtocell will induce co-tier interference to neighboring femtocells.
Thus to jointly handle co-tier and co-channel interference, we
propose an interference-free power and resource block allocation
(IFPRBA) algorithm for closely located, closed access femtocells.
Based on neighboring list, inter-femto-base station distance and
uplink noise power, the IFPRBA algorithm assigns non-interfering
power and resource to femtocells. The IFPRBA algorithm also
guarantees the quality of service to femtouser based on the
knowledge of resource requirement, connection type, and the
tolerable delay budget. Simulation result shows that the interference
power experienced in IFPRBA algorithm is below the tolerable
interference power and hence the overall service success ratio, PRB
efficiency and network throughput are maximum when compared to
conventional resource allocation framework for femtocell (RAFF)
algorithm.
Abstract: This paper presents nonlinear pulse propagation characteristics for different input optical pulse shapes with various input pulse energy levels in semiconductor optical amplifiers. For simulation of nonlinear pulse propagation, finite-difference beam propagation method is used to solve the nonlinear Schrödinger equation. In this equation, gain spectrum dynamics, gain saturation are taken into account which depends on carrier depletion, carrier heating, spectral-hole burning, group velocity dispersion, self-phase modulation and two photon absorption. From this analysis, we obtained the output waveforms and spectra for different input pulse shapes as well as for different input energies. It shows clearly that the peak position of the output waveforms are shifted toward the leading edge which due to the gain saturation of the SOA for higher input pulse energies. We also analyzed and compared the normalized difference of full-width at half maximum for different input pulse shapes in the SOA.
Abstract: Cavitation in cryogenic liquids is widely present in
contemporary science. In the current study, we re-examine a
previously validated acoustic cavitation model which was developed
for a gas bubble in liquid water. Furthermore, simulations of
cryogenic fluids including the thermal effect, the effect of acoustic
pressure amplitude and the frequency of sound field on the bubble
dynamics are presented. A gas bubble (Helium) in liquids Nitrogen,
Oxygen and Hydrogen in an acoustic field at ambient pressure and
low temperature is investigated numerically. The results reveal that
the oscillation of the bubble in liquid Hydrogen fluctuates more than
in liquids Oxygen and Nitrogen. The oscillation of the bubble in
liquids Oxygen and Nitrogen is approximately similar.
Abstract: This work presents a new planar multiband antenna
based on fractal geometry. This structure is optimized and validated
into simulation by using CST-MW Studio. To feed this antenna we
have used a CPW line which makes it easy to be incorporated with
integrated circuits. The simulation results presents a good matching
input impedance and radiation pattern in the GSM band at 900 MHz
and ISM band at 2.4 GHz. The final structure is a dual band fractal
antenna with 70 x 70 mm² as a total area by using an FR4 substrate.
Abstract: Logistics distributors face the issue of having to
provide increasing service levels while being forced to reduce costs at
the same time. Same-day delivery, quick order processing and rapidly
growing ranges of articles are only some of the prevailing challenges.
One key aspect of the performance of an intra-logistics system is how
often and in which amplitude congestions and dysfunctions affect the
processing operations. By gaining knowledge of the so called
‘performance availability’ of such a system during the planning stage,
oversizing and wasting can be reduced whereas planning
transparency is increased. State of the art for the determination of this
KPI is simulation studies. However, their structure and therefore their
results may vary unforeseeably. This article proposes a concept for
the establishment of ‘certified’ and hence reliable and comparable
simulation models.
Abstract: This paper designs the four-phase Boost Converter
which overcomes the problem of high input ripple current and output
ripple voltage. Digital control is more convenient for such a topology
on basis of synchronization, phase shift operation, etc. Simulation
results are presented for open-loop and closed-loop for four phase
boost converter. This control scheme is applicable for PFC rectifiers
as well. Thus a comparative analysis based on the obtained results is
performed.
Abstract: Axial flow fans, while incapable of developing high
pressures, they are well suitable for handling large volumes of air at
relatively low pressures. In general, they are low in cost and possess
good efficiency, and can have blades of airfoil shape. Axial flow fans
show good efficiencies, and can operate at high static pressures if
such operation is necessary. Our objective is to model and analyze
the flow through AXIAL FANS using CFD Software and draw
inference from the obtained results, so as to get maximum efficiency.
The performance of an axial fan was simulated using CFD and the
effect of variation of different parameters such as the blade number,
noise level, velocity, temperature and pressure distribution on the
blade surface was studied. This paper aims to present a final 3D CAD
model of axial flow fan. Adapting this model to the available
components in the market, the first optimization was done. After this
step, CFX flow solver is used to do the necessary numerical analyses
on the aerodynamic performance of this model. This analysis results
in a final optimization of the proposed 3D model which is presented
in this article.
Abstract: In this work, we propose and analyze a model of
Phytoplankton-Zooplankton interaction with harvesting considering
that some species are exploited commercially for food. Criteria for
local stability, instability and global stability are derived and some
threshold harvesting levels are explored to maintain the population
at an appropriate equilibrium level even if the species are exploited
continuously.Further,biological and bionomic equilibria of the system
are obtained and an optimal harvesting policy is also analysed using
the Pantryagin’s Maximum Principle.Finally analytical findings are
also supported by some numerical simulations.
Abstract: The objective of meta-analysis is to combine results
from several independent studies in order to create generalization
and provide evidence base for decision making. But recent studies
show that the magnitude of effect size estimates reported in many
areas of research significantly changed over time and this can
impair the results and conclusions of meta-analysis. A number of
sequential methods have been proposed for monitoring the effect
size estimates in meta-analysis. However they are based on statistical
theory applicable only to fixed effect model (FEM) of meta-analysis.
For random-effects model (REM), the analysis incorporates the
heterogeneity variance, τ 2 and its estimation create complications.
In this paper we study the use of a truncated CUSUM-type test with
asymptotically valid critical values for sequential monitoring in REM.
Simulation results show that the test does not control the Type I error
well, and is not recommended. Further work required to derive an
appropriate test in this important area of applications.
Abstract: Communicating and managing customers’
requirements in software development projects play a vital role in the
software development process. While it is difficult to do so locally, it
is even more difficult to communicate these requirements over
distributed boundaries and to convey them to multiple distribution
customers. This paper discusses the communication of multiple
distribution customers’ requirements in the context of customised
software products. The main purpose is to understand the challenges
of communicating and managing customisation requirements across
distributed boundaries. We propose a model for Communicating
Customisation Requirements of Multi-Clients in a Distributed
Domain (CCRD). Thereafter, we evaluate that model by presenting
the findings of a case study conducted with a company with
customisation projects for 18 distributed customers. Then, we
compare the outputs of the real case process and the outputs of the
CCRD model using simulation methods. Our conjecture is that the
CCRD model can reduce the challenge of communication
requirements over distributed organisational boundaries, and the
delay in decision making and in the entire customisation process
time.