Abstract: Two group of kids (“Safflower cake" and “Control") were fed ad libitum with pelleted total mixed rations. After a 7-days adaptation period, the diet of the “Safflower cake" group were supplemented with 20% of safflower cake. The kids were slaughtered at 96 days of age. Dietary safflower cake did not affect the growth traits of kids. In addition, kids fed experimental diet showed a lower feed intake and consequently a better feed conversion ratio in comparison to the “Control" group. The use of safflower decreased the level of SFA and increased the level of MUFA in kid meat. The level of PUFA was higher in lipid extracted from animals feeding “Control“ diet even if the UFA level was lower. Furthermore, lipid extracted from animals feeding control diet contained more ω6 fatty acids in comparison to kids feeding experimental diet while the opposite trend was observed for the level of ω3 fatty acids. The ω6 to ω3 ratio was significantly affected by diet and in particular this ratio decreased in meat of kids fed experimental diet. Our results indicate that intramuscular fatty acid composition of kid meat can be improved from a human health perspective by inclusion of safflower cake in the diet.
Abstract: This paper applies the homotopy analysis method method to a nonlinear differential-difference equation arising in nanotechnology. Continuum hypothesis on nanoscales is invalid, and a differential-difference model is considered as an alternative approach to describing discontinued problems. Comparison of the approximate solution with the exact one reveals that the method is very effective.
Abstract: EEG signal is one of the oldest measures of brain
activity that has been used vastly for clinical diagnoses and
biomedical researches. However, EEG signals are highly
contaminated with various artifacts, both from the subject and from
equipment interferences. Among these various kinds of artifacts,
ocular noise is the most important one. Since many applications such
as BCI require online and real-time processing of EEG signal, it is
ideal if the removal of artifacts is performed in an online fashion.
Recently, some methods for online ocular artifact removing have
been proposed. One of these methods is ARMAX modeling of EEG
signal. This method assumes that the recorded EEG signal is a
combination of EOG artifacts and the background EEG. Then the
background EEG is estimated via estimation of ARMAX parameters.
The other recently proposed method is based on adaptive filtering.
This method uses EOG signal as the reference input and subtracts
EOG artifacts from recorded EEG signals. In this paper we
investigate the efficiency of each method for removing of EOG
artifacts. A comparison is made between these two methods. Our
undertaken conclusion from this comparison is that adaptive filtering
method has better results compared with the results achieved by
ARMAX modeling.
Abstract: The quality improvements of the environmental
elements could increase the recreational opportunities in a certain
area (destination). The technique of the need for recreation focuses
on choosing certain destinations for recreational purposes. The basic
exchange taken into consideration is the one between the satisfaction
gained after staying in that area and the value expressed in money
and time allocated. The number of tourists in the respective area, the
duration of staying and the money spent including transportation
provide information on how individuals rank the place or certain
aspects of the area (such as the quality of the environmental
elements).
For the statistical analysis of the environmental benefits offered by
an area through the need of recreation technique, the following stages
are suggested:
- characterization of the reference area based on the
statistical variables considered;
- estimation of the environmental benefit through
comparing the reference area with other similar areas
(having the same environmental characteristics), from
the perspective of the statistical variables considered.
The model compared in recreation technique faced with a series of
difficulties which refers to the reference area and correct
transformation of time in money.
Abstract: An experimental study is presented on the effect of
Conservation Agriculture (CA) compared to Conventional
Agriculture (ConvA) upon Maize Yield based on split-plot model.
Two factors have been considered: A Factor-Fertilization with two
variants: A1- N40P40 kg/ha and A2- N90P70 kg/ha; B Factor- Crop
protection with 4 variants : B1- 4 treatments, B2-3 treatments, B3- 2
treatments and B4- 1 treatment. In comparison with conventional
agriculture, CA determined lower maize yields. Fertilization is the
key factor determining a yield gain of 973.58 kg/ha in ConvA and
1,123.33 kg/ha in CA. A reduced number of treatments determined a
yield decline. The A-B interaction had a positive effect on maize
yield when a larger amount of fertilizer and 4 or 3 treatments were
applied in ConvA and a benefic in CA for highest fertilization level
and 2 treatments. The B2A2 ConvA variant was the most efficient
leading to 302.67 kg/ha gain while B3A2 CA variant brought 181.33
kg production gain.
Abstract: This paper deals with the project selection problem. Project selection problem is one of the problems arose firstly in the field of operations research following some production concepts from primary product mix problem. Afterward, introduction of managerial considerations into the project selection problem have emerged qualitative factors and criteria to be regarded as well as quantitative ones. To overcome both kinds of criteria, an analytic network process is developed in this paper enhanced with fuzzy sets theory to tackle the vagueness of experts- comments to evaluate the alternatives. Additionally, a modified version of Least-Square method through a non-linear programming model is augmented to the developed group decision making structure in order to elicit the final weights from comparison matrices. Finally, a case study is considered by which developed structure in this paper is validated. Moreover, a sensitivity analysis is performed to validate the response of the model with respect to the condition alteration.
Abstract: The network of delivering commodities has been an important design problem in our daily lives and many transportation applications. The delivery performance is evaluated based on the system reliability of delivering commodities from a source node to a sink node in the network. The system reliability is thus maximized to find the optimal routing. However, the design problem is not simple because (1) each path segment has randomly distributed attributes; (2) there are multiple commodities that consume various path capacities; (3) the optimal routing must successfully complete the delivery process within the allowable time constraints. In this paper, we want to focus on the design optimization of the Multi-State Flow Network (MSFN) for multiple commodities. We propose an efficient approach to evaluate the system reliability in the MSFN with respect to randomly distributed path attributes and find the optimal routing subject to the allowable time constraints. The delivery rates, also known as delivery currents, of the path segments are evaluated and the minimal-current arcs are eliminated to reduce the complexity of the MSFN. Accordingly, the correct optimal routing is found and the worst-case reliability is evaluated. It has been shown that the reliability of the optimal routing is at least higher than worst-case measure. Two benchmark examples are utilized to demonstrate the proposed method. The comparisons between the original and the reduced networks show that the proposed method is very efficient.
Abstract: The knee bracing steel frame (KBF) is a new kind of energy dissipating frame, which combines excellent ductility and lateral stiffness. In this framing system, a special form of diagonal brace connected to a knee element instead of beam-column joint, is investigated. Recently, a similar system was proposed and named as chevron knee bracing system (CKB) which in comparison with the former system has a better energy absorption characteristic and at the same time retains the elastic nature of the structures. Knee bracing can provide a stiffer bracing system but reduces the ductility of the steel frame. Chevron knee bracing can be employed to provide the desired ductility level for a design. In this article, relation between seismic performance and structural parameters of the two above mentioned systems are investigated and compared. Frames with similar dimensions but various heights in both systems are designed according to Iranian code of practice for seismic resistant design of building, and then based on a non-linear push over static analysis; the seismic parameters such as behavior factor and performance levels are compared.
Abstract: Combining classifiers is a useful method for solving
complex problems in machine learning. The ECOC (Error Correcting
Output Codes) method has been widely used for designing combining
classifiers with an emphasis on the diversity of classifiers. In this
paper, in contrast to the standard ECOC approach in which individual
classifiers are chosen homogeneously, classifiers are selected
according to the complexity of the corresponding binary problem. We
use SATIMAGE database (containing 6 classes) for our experiments.
The recognition error rate in our proposed method is %10.37 which
indicates a considerable improvement in comparison with the
conventional ECOC and stack generalization methods.
Abstract: Composite laminates are relatively weak in out of
plane loading, inter-laminar stress, stress concentration near the edge
and stress singularities. This paper develops a new analytical
formulation for laminated composite rotating disc fabricated from
symmetric sequential quasi isotropic layers to predict three
dimensional stress and deformation. This analysis is necessary to
evaluate mechanical integrity of fiber reinforced multi-layer
laminates used for high speed rotating applications such as high
speed impellers. Three dimensional governing equations are written
for rotating composite disc. Explicit solution is obtained with
"Frobenius" expansion series. Based on analytical results, there are
two separate zones of three dimensional stress fields in centre and
edge of rotating disc. For thin discs, out of plane deformations and
stresses are small in comparison with plane ones. For relatively thick
discs deformation and stress fields are three dimensional.
Abstract: Fuzzy Cognitive Maps (FCMs) is a causal graph, which shows the relations between essential components in complex systems. Experts who are familiar with the system components and their relations can generate a related FCM. There is a big gap when human experts cannot produce FCM or even there is no expert to produce the related FCM. Therefore, a new mechanism must be used to bridge this gap. In this paper, a novel learning method is proposed to construct causal graph based on historical data and by using metaheuristic such Tabu Search (TS). The efficiency of the proposed method is shown via comparison of its results of some numerical examples with those of some other methods.
Abstract: In this paper, we present the 2006 survey study origin destination and price that we carried out during 2006 fall in the area in the Moroccan region of Rabat-Salé-Zemmour-Zaer. The survey concerns the people-s characteristics, their displacements behavior and the price that they will be able to pay for a tramway ticket. The main objective is to study a set of relative features to the households and to their displacement's habits and to their choices among public and privet transport modes. A comparison between this survey results and that of the 1996's is made. A pricing scheme is also given according to the tram capacity. (The Rabat-Salé tramway is under construction right now and it will be operational beginning 2010).
Abstract: recurrent neural network (RNN) is an efficient tool for
modeling production control process as well as modeling services. In
this paper one RNN was combined with regression model and were
employed in order to be checked whether the obtained data by the
model in comparison with actual data, are valid for variable process
control chart. Therefore, one maintenance process in workshop of
Esfahan Oil Refining Co. (EORC) was taken for illustration of
models. First, the regression was made for predicting the response
time of process based upon determined factors, and then the error
between actual and predicted response time as output and also the
same factors as input were used in RNN. Finally, according to
predicted data from combined model, it is scrutinized for test values
in statistical process control whether forecasting efficiency is
acceptable. Meanwhile, in training process of RNN, design of
experiments was set so as to optimize the RNN.
Abstract: As there has been a recognizable transition in
automotive industry from mass production to mass customization,
automobile manufacturers and their suppliers have been seeking ways
for more flexible and efficient processes. Eventually, modular
production is currently being applied to manage the changing orders of
the industry. In this paper, two different modular assembly line
concepts were studied: conveyor line and box assembly line.
Mathematical model for two assembly line concepts were developed
and their production line efficiency were compared as a performance
measure to improve their assembly line balancing.
Abstract: Asynchronous Transfer Mode (ATM) is widely used
in telecommunications systems to send data, video and voice at a
very high speed. In ATM network optimizing the bandwidth through
dynamic routing is an important consideration. Previous research
work shows that traditional optimization heuristics result in suboptimal
solution. In this paper we have explored non-traditional
optimization technique. We propose comparison of two such
algorithms - Genetic Algorithm (GA) and Tabu search (TS), based on
non-traditional Optimization approach, for solving the dynamic
routing problem in ATM networks which in return will optimize the
bandwidth. The optimized bandwidth could mean that some
attractive business applications would become feasible such as high
speed LAN interconnection, teleconferencing etc. We have also
performed a comparative study of the selection mechanisms in GA
and listed the best selection mechanism and a new initialization
technique which improves the efficiency of the GA.
Abstract: In this paper, the difference between the Alternating
Direction Method (ADM) and the Non-Splitting Method (NSM) is
investigated, while both methods applied to the simulations for 2-D
multimaterial radiation diffusion issues. Although the ADM have the
same accuracy orders with the NSM on the uniform meshes, the
accuracy of ADM will decrease on the distorted meshes or the
boundary of domain. Numerical experiments are carried out to
confirm the theoretical predication.
Abstract: This paper presents the experimental results on
ageing deterioration of silicone rubber outdoor polymer insulator
under salt water dip wheel test based on IEC 62217. In order to comparison effect of chemical contents, silicone rubber outdoor
polymer insulators having same configuration and leakage distant
from two manufactures were tested together continuously 30,000 test cycles. Many discharge activities were observed in during the test.
After 30,000 test cycles, in spite of same configuration, differences in
degree of surface aging were observed. Physical analysis such as
decreasing in hydrophobicity and increasing in hardness
measurement were measured on two-type tested specimen surface in order to confirm degree of surface ageing. Furthermore, chemical
analysis by ATR-FTIR to diagnose the chemical change of tested
specimen surface was conducted to confirm the physical analysis results.
Abstract: Plant tissue culture is an important in vitro technology applied for agricultural and industrial production. A sterile condition of culture medium is one of the main aspects. The alternative technique for medium sterilization to replace autoclaving was carried out. For sterilization of plant tissue culture medium without autoclaving, ten commercial pure essential oils and 5 disinfectants were tested. Each essential oil or disinfectant was added to a 20-mL Murashige and Skoog (MS) medium before medium was solidified in a 120-mL container, kept for 2 weeks before evaluating sterile conditions. Treated media, supplemented with essential oils or disinfectants, were compared to control medium, autoclaved at 121 degree Celsius for 15 min. Sterile conditions of MS medium were found 100% from betel oil or clove oil (18 mL/20 mL medium), cinnamon oil (36 mL/20 mL medium), lavender oil or holy basil oil (108 mL/20 mL medium), and lemon oil or tea tree oil or turmeric oil (252 mL/20 mL medium), compared to 100% sterile condition from autoclaved medium. For disinfectants, 2% iodine + 2.4% potassium iodide, 2% merbromine solution, 10% povidone-iodine, 6% sodium hypochlorite or 0.1% thimerosal at 36 mL/20 mL medium provided 100% sterile conditions. Furthermore, growth of new shoots from chrysanthemum node explants on treated media (fresh weight, shoot length, root length and number of node) were also reported and discussed in the comparison of those on autoclaved medium.
Abstract: In this paper a special kind of buffer management policy is studied where the packet are preempted even when sufficient space is available in the buffer for incoming packets. This is done to congestion for future incoming packets to improve QoS for certain type of packets. This type of study has been done in past for ATM type of scenario. We extend the same for heterogeneous traffic where data rate and size of the packets are very versatile in nature. Typical example of this scenario is the buffer management in Differentiated Service Router. There are two aspects that are of interest. First is the packet size: whether all packets have same or different sizes. Second aspect is the value or space priority of the packets, do all packets have the same space priority or different packets have different space priorities. We present two types of policies to achieve QoS goals for packets with different priorities: the push out scheme and the expelling scheme. For this work the scenario of packets of variable length is considered with two space priorities and main goal is to minimize the total weighted packet loss. Simulation and analytical studies show that, expelling policies can outperform the push out policies when it comes to offering variable QoS for packets of two different priorities and expelling policies also help improve the amount of admissible load. Some other comparisons of push out and expelling policies are also presented using simulations.
Abstract: In this paper, the babbitting of a bearing in boiler feed pump of an electromotor has been studied. These bearings have an important role in reducing the shut down times in the pumps, compressors and turbines. The most conventional method in babbitting is casting as a melting method. The comparison between thermal spray and casting methods in babbitting shows that the thermal spraying babbitt layer has better performance and tribological behavior. The metallurgical and tribological analysis such as SEM, EDS and wet chemical analysis has been made in the Babbitt alloys and worn surfaces. Two type of babbitt materials: tinbase and lead-base babbitt was used. The benefits of thermally sprayed babbitt layers are completely clear especially in large bearings.