Abstract: The use of nanostructured semiconducting material to catalyze degradation of environmental pollutants still receives much attention to date. One of the desired characteristics for pollutant degradation under ultra-violet visible light is the materials with extended carrier charge separation that allows for electronic transfer between the catalyst and the pollutants. In this work, zinc oxide n-type semiconductor vertically aligned structures were fabricated on silicon (100) substrates using the chemical bath deposition method. The as-synthesized structures were treated with nickel and sulphur. X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy were used to characterize the phase purity, structural dimensions and elemental composition of the obtained structures respectively. Photoluminescence emission measurements showed a decrease in both the near band edge emission as well as the defect band emission upon addition of nickel and sulphur with different concentrations. This was attributed to increased charger-carrier-separation due to the presence of Ni-S material on ZnO surface, which is linked to improved charge transfer during photocatalytic reactions.
Abstract: The majority of today’s mobile robots are very dependent on battery power. Mobile robots can operate untethered for a number of hours but eventually they will need to recharge their batteries in-order to continue to function. While computer processing and sensors have become cheaper and more powerful each year, battery development has progress very little. They are slow to re-charge, inefficient and lagging behind in the general progression of robotic development we see today. However, batteries are relatively cheap and when fully charged, can supply high power output necessary for operating heavy mobile robots. As there are no cheap alternatives to batteries, we need to find efficient ways to manage the power that batteries provide during their operational lifetime. This paper proposes the use of autonomic principles of self-adaption to address the behavioral changes a battery experiences as it gets older. In life, as we get older, we cannot perform tasks in the same way as we did in our youth; these tasks generally take longer to perform and require more of our energy to complete. Batteries also suffer from a form of degradation. As a battery gets older, it loses the ability to retain the same charge capacity it would have when brand new. This paper investigates how we can adapt the current state of a battery charge and cycle count, to the requirements of a mobile robot to perform its tasks.
Abstract: Muscle regeneration after injury (as irradiation) is of great importance. However, the molecular and cellular mechanisms are still unclear. Cytokines are believed to play fundamental role in the different stages of muscle regeneration. They are secreted by many cell populations, but the predominant producers are macrophages and helper T cells. On the other hand, it has been shown that adipose tissue derived stromal/stem cell (ASC) injection could improve muscle regeneration. Stem cells probably induce the coordinated modulations of gene expression in different macrophage cells. Therefore, we investigated the patterns and timing of changes in gene expression of different cytokines occurring upon stem cells loading. Muscle regeneration was studied in an irradiated muscle of minipig animal model in presence or absence of ASC treatment (irradiated and treated with ASCs, IRR+ASC; irradiated not-treated with ASCs, IRR; and non-irradiated no-IRR). We characterized macrophage populations by immunolabeling in the different conditions. In our study, we found mostly M2 and a few M1 macrophages in the IRR+ASC samples. However, only few M2b macrophages were noticed in the IRR muscles. In addition, we found intensive fibrosis in the IRR samples. With in situ hybridization and immunolabeling, we analyzed the cytokine expression of the different macrophages and we showed that M2d macrophage are the most abundant in the IRR+ASC samples. By in situ hybridization, strong expression of the transforming growth factor β (TGF-β) was observed in the IRR+ASC but very week in the IRR samples. But when we analyzed TGF-β level with immunolabeling the expression was very different: many M2 macrophages showed week expression in IRR+ASC and few cells expressing stronger level in IRR muscles. Therefore, we investigated the MMP expressions in the different muscles. Our data showed that the M2 macrophages of the IRR+ASC muscle expressed MMP2 proteins. Our working hypothesis is that MMP2 expression of the M2 macrophages can decrease fibrosis in the IRR+ASC muscle by capturing TGF-β.
Abstract: Cellulose acetate (CA) is a natural biodegradable polymer. It forms transparent films by the casting technique. CA suffers from high degree of water permeability as well as the low thermal stability at high temperatures. To adjust the CA polymeric films to the manufacture of food packaging, its thermal and mechanical properties should be improved. The modification of CA by grafting it with N-Amino phenyl maleimide (N-APhM) led to the construction of hydrophobic branches throughout the polymeric matrix which reduced its wettability as compared to the parent CA. The branches built onto the polymeric chains had been characterized by UV/Vis, 13C-NMR and ESEM. The improvement of the thermal properties was investigated and compared to the parent CA using thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), differential thermal analysis (DTA), contact angle and mechanical testing measurements. The results revealed that the water-uptake was reduced by increasing the graft percentage. The thermal and mechanical properties were also improved.
Abstract: With the increasing demand of bandwidth and data rate,
there is a dire need to implement antenna systems in mobile phones
which are able to fulfill user requirements. A monopole antenna
system with multi-antennas configurations is proposed considering
the feasibility and user demand. The multi-antenna structure is
referred to as multi-input multi-output (MIMO) antenna system. The
multi-antenna system comprises of 4 antennas operating below 6
GHz frequency bands for 4G/LTE and 4 antenna for 5G applications
at 28 GHz and the dimension of board is 120 × 70 × 0.8mm3.
The suggested designs is feasible with a structure of low-profile
planar-antenna and is adaptable to smart cell phones and handheld
devices. To the best of our knowledge, this is the first design
compared to the literature by having integrated antenna system
for two standards, i.e., 4G and 5G. All MIMO antenna systems
are simulated on commercially available software, which is high
frequency structures simulator (HFSS).
Abstract: In this paper, a method of fast 3D topography modeling using the high-resolution camera images is studied based on the characteristics of Unmanned Aerial Vehicle (UAV) system for low altitude aerial photogrammetry and the need of three dimensional (3D) urban landscape modeling. Firstly, the existing high-resolution digital camera with special design of overlap images is designed by reconstructing and analyzing the auto-flying paths of UAVs, which improves the self-calibration function to achieve the high precision imaging by software, and further increased the resolution of the imaging system. Secondly, several-angle images including vertical images and oblique images gotten by the UAV system are used for the detail measure of urban land surfaces and the texture extraction. Finally, the aerial photography and 3D topography construction are both developed in campus of Chang-Jung University and in Guerin district area in Tainan, Taiwan, provide authentication model for construction of 3D topography based on combined UAV-based camera images from system. The results demonstrated that the UAV system for low altitude aerial photogrammetry can be used in the construction of 3D topography production, and the technology solution in this paper offers a new, fast, and technical plan for the 3D expression of the city landscape, fine modeling and visualization.
Abstract: Crank shaft length, connecting rod length, crank angle, engine rpm, cylinder bore, mass of piston and compression ratio are the inputs that can control the performance of the slider crank mechanism and then its efficiency. Several combinations of these seven inputs are used and compared. The throughput engine torque predicted by the simulation is analyzed through two different regression models, with and without interaction terms, developed according to multi-linear regression using LU decomposition to solve system of algebraic equations. These models are validated. A regression model in seven inputs including their interaction terms lowered the polynomial degree from 3rd degree to 1st degree and suggested valid predictions and stable explanations.
Abstract: The advancement in various concrete ingredients like plasticizers, additives and fibers, etc. has enabled concrete technologists to develop many viable varieties of special concretes in recent decades. Such various varieties of concrete have significant enhancement in green as well as hardened properties of concrete. A prudent selection of appropriate type of concrete can resolve many design and application issues in construction projects. This paper focuses on usage of self-compacting concrete, high early strength concrete, structural lightweight concrete, fiber reinforced concrete, high performance concrete and ultra-high strength concrete in the structures. The modified properties of strength at various ages, flowability, porosity, equilibrium density, flexural strength, elasticity, permeability etc. need to be carefully studied and incorporated into the design of the structures. The paper demonstrates various mixture combinations and the concrete properties that can be leveraged. The selection of such products based on the end use of structures has been proposed in order to efficiently utilize the modified characteristics of these concrete varieties. The study involves mapping the characteristics with benefits and savings for the structure from design perspective. Self-compacting concrete in the structure is characterized by high shuttering loads, better finish, and feasibility of closer reinforcement spacing. The structural design procedures can be modified to specify higher formwork strength, height of vertical members, cover reduction and increased ductility. The transverse reinforcement can be spaced at closer intervals compared to regular structural concrete. It allows structural lightweight concrete structures to be designed for reduced dead load, increased insulation properties. Member dimensions and steel requirement can be reduced proportionate to about 25 to 35 percent reduction in the dead load due to self-weight of concrete. Steel fiber reinforced concrete can be used to design grade slabs without primary reinforcement because of 70 to 100 percent higher tensile strength. The design procedures incorporate reduction in thickness and joint spacing. High performance concrete employs increase in the life of the structures by improvement in paste characteristics and durability by incorporating supplementary cementitious materials. Often, these are also designed for slower heat generation in the initial phase of hydration. The structural designer can incorporate the slow development of strength in the design and specify 56 or 90 days strength requirement. For designing high rise building structures, creep and elasticity properties of such concrete also need to be considered. Lastly, certain structures require a performance under loading conditions much earlier than final maturity of concrete. High early strength concrete has been designed to cater to a variety of usages at various ages as early as 8 to 12 hours. Therefore, an understanding of concrete performance specifications for special concrete is a definite door towards a superior structural design approach.
Abstract: Due to the numerous advantages of steel corrugated
web girders, its application field is growing for bridges as well as for
buildings. The global stability behavior of such girders is
significantly larger than those of conventional I-girders with flat web,
thus the application of the structural steel material can be
significantly reduced. Design codes and specifications do not provide
clear and complete rules or recommendations for the determination of
the lateral torsional buckling (LTB) resistance of corrugated web
girders. Therefore, the authors made a thorough investigation
regarding the LTB resistance of the corrugated web girders. Finite
element (FE) simulations have been performed to develop new
design formulas for the determination of the LTB resistance of
trapezoidally corrugated web girders. FE model is developed
considering geometrical and material nonlinear analysis using
equivalent geometric imperfections (GMNI analysis). The equivalent
geometric imperfections involve the initial geometric imperfections
and residual stresses coming from rolling, welding and flame cutting.
Imperfection sensitivity analysis was performed to determine the
necessary magnitudes regarding only the first eigenmodes shape
imperfections. By the help of the validated FE model, an extended
parametric study is carried out to investigate the LTB resistance for
different trapezoidal corrugation profiles. First, the critical moment of
a specific girder was calculated by FE model. The critical moments
from the FE calculations are compared to the previous analytical
calculation proposals. Then, nonlinear analysis was carried out to
determine the ultimate resistance. Due to the numerical
investigations, new proposals are developed for the determination of
the LTB resistance of trapezoidally corrugated web girders through a
modification factor on the design method related to the conventional
flat web girders.
Abstract: The latent heat thermal energy storage system is a
thrust area of research due to exuberant thermal energy storage
potential. The thermal performance of PCM is significantly
augmented by installation of the high thermal conductivity fins. The
objective of the present study is to obtain optimum size and location
of the fins to enhance diffusion heat transfer without altering overall
melting time. Hence, the constructal theory is employed to eliminate,
resize, and re-position the fins. A numerical code based on conjugate
heat transfer coupled enthalpy porosity approached is developed to
solve Navier-Stoke and energy equation. The numerical results show
that the constructal fin design has enhanced the thermal performance
along with the increase in the overall volume of PCM when
compared to conventional. The overall volume of PCM is found to be
increased by half of total of volume of fins. The elimination and repositioning
the fins at high temperature gradient from low
temperature gradient is found to be vital.
Abstract: As part of a ‘Morphing-Wing’ idea, this study consists
of measuring how a winglet, which is able to change its shape during
the flight, is efficient. Conventionally, winglets are fixed-vertical
platforms at the wingtips, optimized for a cruise condition that the
airplane should use most of the time. However, during a cruise, an
airplane flies through a lot of cruise conditions corresponding to
altitudes variations from 30,000 to 45,000 ft. The fixed winglets are
not optimized for these variations, and consequently, they are
supposed to generate some drag, and thus to deteriorate aircraft fuel
consumption. This research assumes that it exists a winglet position
that reduces the fuel consumption for each cruise condition. In this
way, the methodology aims to find these optimal winglet positions,
and to further simulate, and thus estimate the fuel consumption of an
aircraft wearing this type of adaptive winglet during several cruise
conditions. The adaptive winglet is assumed to have degrees of
freedom given by the various changes of following surfaces: the tip
chord, the sweep and the dihedral angles. Finally, results obtained
during cruise simulations are presented in this paper. These results
show that an adaptive winglet can reduce, thus improve up to 2.12%
the fuel consumption of an aircraft during a cruise.
Abstract: The discussion about elements of cultural heritage and
their relevance among the ancient villages is comparably insufficient.
The protection work is strongly influenced by touristic development
and cultural gimmick, resulting in low protection efficiency and many
omissions. Historical villages as the cultural settlement patterns bear a
large number of heritage relics. They were regionally scattered with a
clear characteristic of gathering. First of all, this study proposes the
association and similarities of the forming mechanism between four
historic cultural villages in Mian Mountain. Secondly, the study
reveals that these villages own the strategic pass, underground
passage, and the mountain barrier. Thirdly, based on the differentiated
characteristics of villages’ space, the study discusses about the
integrated conservation from three levels: the regional heritage
conservation, the cultural line shaping, and the featured brand
building.
Abstract: In this paper, an (irregular) case relating to base circle, root circle, and pressure angle has been discussed and a computer programme has been developed to simulate and plot spur gear tooth profile, including involute and trochoid curves based on the formulation of rack cutter using different values of pressure angle and profile shift factor and it gave the values of all important geometric parameters. The results showed the flexibility of this approach and versatility of the programme to draw many different cases of spur gear teeth of any module, pressure angle, profile shift factor, number of teeth and rack cutter tip radius. The procedure developed can be extended to produce finite element models of heretofore intractable geometrical forms, to exploring fabrication of nonstandard tooth forms also. Finite elements model of these irregular cases have been built using above programme, and modal analysis has been done using ANSYS software, and natural frequencies of these selected cases have been obtained and discussed.
Abstract: The purpose of the present research is to equate two
test forms as part of a study to evaluate the educational effectiveness
of the ARTé: Mecenas art history learning game. The researcher
applied Item Response Theory (IRT) procedures to calculate item,
test, and mean-sigma equating parameters. With the sample size
n=134, test parameters indicated “good” model fit but low Test
Information Functions and more acute than expected equating
parameters. Therefore, the researcher applied equipercentile equating
and linear equating to raw scores and compared the equated form
parameters and effect sizes from each method. Item scaling in IRT
enables the researcher to select a subset of well-discriminating items.
The mean-sigma step produces a mean-slope adjustment from the
anchor items, which was used to scale the score on the new form
(Form R) to the reference form (Form Q) scale. In equipercentile
equating, scores are adjusted to align the proportion of scores in each
quintile segment. Linear equating produces a mean-slope adjustment,
which was applied to all core items on the new form. The study
followed a quasi-experimental design with purposeful sampling of
students enrolled in a college level art history course (n=134) and
counterbalancing design to distribute both forms on the pre- and posttests.
The Experimental Group (n=82) was asked to play ARTé:
Mecenas online and complete Level 4 of the game within a two-week
period; 37 participants completed Level 4. Over the same period, the
Control Group (n=52) did not play the game. The researcher
examined between group differences from post-test scores on test
Form Q and Form R by full-factorial Two-Way ANOVA. The raw
score analysis indicated a 1.29% direct effect of form, which was
statistically non-significant but may be practically significant. The
researcher repeated the between group differences analysis with all
three equating methods. For the IRT mean-sigma adjusted scores,
form had a direct effect of 8.39%. Mean-sigma equating with a small
sample may have resulted in inaccurate equating parameters.
Equipercentile equating aligned test means and standard deviations,
but resultant skewness and kurtosis worsened compared to raw score
parameters. Form had a 3.18% direct effect. Linear equating
produced the lowest Form effect, approaching 0%. Using linearly
equated scores, the researcher conducted an ANCOVA to examine
the effect size in terms of prior knowledge. The between group effect
size for the Control Group versus Experimental Group participants
who completed the game was 14.39% with a 4.77% effect size
attributed to pre-test score. Playing and completing the game
increased art history knowledge, and individuals with low prior
knowledge tended to gain more from pre- to post test. Ultimately,
researchers should approach test equating based on their theoretical
stance on Classical Test Theory and IRT and the respective assumptions. Regardless of the approach or method, test equating
requires a representative sample of sufficient size. With small sample
sizes, the application of a range of equating approaches can expose
item and test features for review, inform interpretation, and identify
paths for improving instruments for future study.
Abstract: The world-wide population of people over 60 years
of age is growing rapidly. The explosion is placing increasingly
onerous demands on individual families, multiple industries and
entire countries. Current, human-intensive approaches to eldercare
are not sustainable, but IoT and AI technologies can help. The
Knowledge Reactor (KR) is a contextual, data fusion engine built to
address this and other similar problems. It fuses and centralizes IoT
and System of Record/Engagement data into a reactive knowledge
graph. Cognitive applications and services are constructed with its
multiagent architecture. The KR can scale-up and scaledown, because
it exploits container-based, horizontally scalable services for graph
store (JanusGraph) and pub-sub (Kafka) technologies. While the KR
can be applied to many domains that require IoT and AI technologies,
this paper describes how the KR specifically supports the challenging
domain of cognitive eldercare. Rule- and machine learning-based
analytics infer activities of daily living from IoT sensor readings. KR
scalability, adaptability, flexibility and usability are demonstrated.
Abstract: This paper describes the design and implementation of
web system for continuable and viable collaboration. This study
proposes the improvement of the system based on a result of a certain
practice. As contemporary higher education information environments
transform, this study highlights the significance of university identity
and college identity that are formed continuously through independent
activities of the students. Based on these discussions, the present study
proposes a practical media environment design which facilitates the
processes of organizational identity formation based on a continuous
and cyclical model. Even if users change by this system, the
communication system continues operation and cooperation. The
activity becomes the archive and produces new activity. Based on the
result, this study elaborates a plan with a re-design by a system from
the viewpoint of second-order cybernetics. Systems theory is a
theoretical foundation for our study.
Abstract: Tire noise has a significant impact on ride quality
and vehicle interior comfort, even at low frequency. Reduction of
tire noise is especially important due to strict state and federal
environmental regulations. The primary sources of tire noise are the
low frequency structure-borne noise and the noise that originates from
the release of trapped air between the tire tread and road surface
during each revolution of the tire. The frequency response of the tire
changes at low and high frequency. At low frequency, the tension
and bending moment become dominant, while the internal structure
and local deformation become dominant at higher frequencies. Here,
we analyze tire response in terms of deformation and rolling velocity
at low revolution frequency. An Abaqus FEA finite element model
is used to calculate the static and dynamic response of a rolling tire
under different rolling conditions. The natural frequencies and mode
shapes of a deformed tire are calculated with the FEA package where
the subspace-based steady state dynamic analysis calculates dynamic
response of tire subjected to harmonic excitation. The analysis was
conducted on the dynamic response at the road (contact point of tire
and road surface) and side nodes of a static and rolling tire when
the tire was excited with 200 N vertical load for a frequency ranging
from 20 to 200 Hz. The results show that frequency has little effect on
tire deformation up to 80 Hz. But between 80 and 200 Hz, the radial
and lateral components of displacement of the road and side nodes
exhibited significant oscillation. For the static analysis, the fluctuation
was sharp and frequent and decreased with frequency. In contrast, the
fluctuation was periodic in nature for the dynamic response of the
rolling tire. In addition to the dynamic analysis, a steady state rolling
analysis was also performed on the tire traveling at ground velocity
with a constant angular motion. The purpose of the computation
was to demonstrate the effect of rotating motion on deformation and
rolling velocity with respect to a fixed Newtonian reference point.
The analysis showed a significant variation in deformation and rolling
velocity due to centrifugal and Coriolis acceleration with respect to
a fixed Newtonian point on ground.
Abstract: Space syntax, a paradigm of the urban research, which
manifests people’s intuitive and abstract perception of a material
space with a solid mathematical way, explores how space represents
its social characteristics. Taking Xiazhuang village and Shijia Village
in Huzhou as an example and focusing on inward structure and street
space, this article recognizes the connotative significance of the
settlement with the aid of space syntax theory and quantitative
analysis method from the perspective of spatial configuration to
present relevant suggestions for its future planning and provides
references for traditional rural settlement protection.
Abstract: Bullet penetration in steel plate is investigated with
the help of three-dimensional, non-linear, transient, dynamic, finite
elements analysis using explicit time integration code LSDYNA. The
effect of large strain, strain-rate and temperature at very high velocity
regime was studied from number of simulations of semi-spherical
nose shape bullet penetration through single layered circular plate
with 2 mm thickness at impact velocities of 500, 1000, and 1500 m/s
with the help of Johnson Cook material model. Mie-Gruneisen
equation of state is used in conjunction with Johnson Cook material
model to determine pressure-volume relationship at various points of
interests. Two material models viz. Plastic-Kinematic and Johnson-
Cook resulted in different deformation patterns in steel plate. It is
observed from the simulation results that the velocity drop and loss of
kinetic energy occurred very quickly up to perforation of plate, after
that the change in velocity and changes in kinetic energy are
negligibly small. The physics behind this kind of behaviour is
presented in the paper.
Abstract: In this paper, the velocity potential and stream
function of capture zone for a well field in an aquifer bounded by two
parallel streams with or without a uniform regional flow of any
directions are presented. The well field includes any number of
extraction or injection wells or a combination of both types with any
pumping rates. To delineate the capture envelope, the potential and
streamlines equations are derived by conformal mapping method.
This method can help us to release constrains of other methods. The
equations can be applied as useful tools to design in-situ groundwater
remediation systems, to evaluate the surface–subsurface water
interaction and to manage the water resources.