Abstract: In this paper a procedure for the split-pipe design of looped water distribution network based on the use of simulated annealing is proposed. Simulated annealing is a heuristic-based search algorithm, motivated by an analogy of physical annealing in solids. It is capable for solving the combinatorial optimization problem. In contrast to the split-pipe design that is derived from a continuous diameter design that has been implemented in conventional optimization techniques, the split-pipe design proposed in this paper is derived from a discrete diameter design where a set of pipe diameters is chosen directly from a specified set of commercial pipes. The optimality and feasibility of the solutions are found to be guaranteed by using the proposed method. The performance of the proposed procedure is demonstrated through solving the three well-known problems of water distribution network taken from the literature. Simulated annealing provides very promising solutions and the lowest-cost solutions are found for all of these test problems. The results obtained from these applications show that simulated annealing is able to handle a combinatorial optimization problem of the least cost design of water distribution network. The technique can be considered as an alternative tool for similar areas of research. Further applications and improvements of the technique are expected as well.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: A Personal Distributed Environment (PDE) is an
example of an IP-based system architecture designed for future
mobile communications. In a single PDE, there exist several Subnetworks
hosting devices located across the infrastructure, which will
inter-work with one another through the coordination of a Device
Management Entity (DME). Some of these Sub-networks are fixed
and some are mobile. In order to support Mobile Sub-networks
mobility in the PDE, the PDE-NEMO protocol was proposed. This
paper discussed the signalling cost analysis of PDE-NEMO by use of
a detailed simulation model. The paper started with the introduction
of the protocol, followed by the experiments and results and then
followed by discussions.
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Abstract: Social interest and demand on Home-Network has
been increasing greatly. Although various services are being
introduced to respond to such demands, they can cause serious
security problems when linked to the open network such as Internet.
This paper reviews the security requirements to protect the service
users with assumption that the Home-Network environment is
connected to Internet and then proposes the security model based on
the requirement. The proposed security model can satisfy most of the
requirements and further can be dynamically applied to the future
ubiquitous Home-Networks.
Abstract: Adsorption of Toluidine blue dye from aqueous solutions onto Neem Leaf Powder (NLP) has been investigated. The surface characterization of this natural material was examined by Particle size analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) spectroscopy and X-Ray Diffraction (XRD). The effects of process parameters such as initial concentration, pH, temperature and contact duration on the adsorption capacities have been evaluated, in which pH has been found to be most effective parameter among all. The data were analyzed using the Langmuir and Freundlich for explaining the equilibrium characteristics of adsorption. And kinetic models like pseudo first- order, second-order model and Elovich equation were utilized to describe the kinetic data. The experimental data were well fitted with Langmuir adsorption isotherm model and pseudo second order kinetic model. The thermodynamic parameters, such as Free energy of adsorption (AG"), enthalpy change (AH') and entropy change (AS°) were also determined and evaluated.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: This article discusses the concept of student ownership of knowledge and seeks to determine how to move students from knowledge acquisition to knowledge application and ultimately to knowledge generation in a virtual setting. Instructional strategies for fostering student engagement in a virtual environment are critical to the learner-s strategic ownership of the knowledge. A number of relevant theories that focus on learning, affect, needs and adult concerns are presented to provide a basis for exploring the transfer of knowledge from teacher to learner. A model under development is presented that combines the dimensions of knowledge approach, the teacher-student relationship with regards to knowledge authority and teaching approach to demonstrate the recursive and scaffolded design for creation of virtual learning environments.
Abstract: The importance of inter-organizational system (IOS)
has been increasingly recognized by organizations. However, IOS
adoption has proved to be difficult and, at this stage, why this is so is
not fully uncovered. In practice, benefits have often remained
concentrated, primarily accruing to the dominant party, resulting in
low rates of adoption and usage, and often culminating in the failure
of the IOS. The main research question is why organizations initiate
or join IOS and what factors influence their adoption and use levels.
This paper reviews the literature on IOS adoption and proposes a
theoretical framework in order to identify the critical factors to
capture a complete picture of IOS adoption. With our proposed
critical factors, we are able to investigate their relative contributions
to IOS adoption decisions. We obtain findings that suggested that
there are five groups of factors that significantly affect the adoption
and use decision of IOS in the Supply Chain Management (SCM)
context: 1) interorganizational context, 2) organizational context, 3)
technological context, 4) perceived costs, and 5) perceived benefits.
Abstract: MABENA model is a complementary model in
comparison with traditional models such as HCMS, CMS and etc.
New factors, which have effects on preparation of strategic plans and
their sequential order in MABENA model is the platform of
presented road map in this paper.Study review shows, factors such as
emerging new critical success factors for strategic planning,
improvement of international strategic models, increasing the
maturity of companies and emerging new needs leading to design a
new model which can be responsible for new critical factors and
solve the limitations of previous strategic management models.
Preparation of strategic planning need more factors than introduced
in traditional models. The needed factors includes determining future
Critical Success Factors and competencies, defining key processes,
determining the maturity of the processes, considering all aspects of
the external environment etc. Description of aforementioned
requirements, the outcomes and their order is developing and
presenting the MABENA model-s road map in this paper. This study
presents a road map for strategic planning of the Iranian
organizations.
Abstract: This article stands in the context of rural communities
in Brazil, where, like many others emerging countries, the
overwhelming increasing markets and the overcrowded cities are
leaving behind informal settlements based on obsolete agricultural
economies and techniques. The pilot project for the community of
Goiabeira reflects the attempt to imagine a development model that
privileges the actual improvement of living conditions, the education
and training, the social inclusion and participation of the dwellers of
rural communities. Through the inclusion of operative public space,
the aim is for them to become self-sustaining, encouraging the use of
local resources for appropriate architectural, ecological and energy
technologies and devices, that are efficient, affordable and foster
community participation, in the respect of the surrounding
environment.
Abstract: In this study, a reformer model simulation to use
refinery (Farashband refinery, Iran) waste natural gas. In the
petroleum and allied sectors where natural gas is being encountered
(in form of associated gas) without prior preparation for its positive
use, its combustion (which takes place in flares, an equipment through
which they are being disposed) has become a great problem because
of its associated environmental problems in form of gaseous emission.
The proposed model is used to product syngas from waste natural gas.
A detailed steady model described by a set of ordinary differential and
algebraic equations was developed to predict the behavior of the
overall process. The proposed steady reactor model was validated
against process data of a reformer synthesis plant recorded and a good
agreement was achieved. H2/CO ratio has important effect on Fischer-
Tropsch synthesis reactor product and we try to achieve this parameter
with best designing reformer reactor. We study different kind of
reformer reactors and then select auto thermal reforming process of
natural gas in a fixed bed reformer that adjustment H2/CO ratio with
CO2 and H2O injection. Finally a strategy was proposed for prevention
of extra natural gas to atmosphere.
Abstract: This paper presents the development of adaptive
distance relay for protection of parallel transmission line with mutual
coupling. The proposed adaptive relay, automatically adjusts its
operation based on the acquisition of the data from distance relay of
adjacent line and status of adjacent line from line circuit breaker IED
(Intelligent Electronic Device). The zero sequence current of the
adjacent parallel transmission line is used to compute zero sequence
current ratio and the mutual coupling effect is fully compensated.
The relay adapts to changing circumstances, like failure in
communication from other relays and non - availability of adjacent
transmission line. The performance of the proposed adaptive relay is
tested using steady state and dynamic test procedures. The fault
transients are obtained by simulating a realistic parallel transmission
line system with mutual coupling effect in PSCAD. The evaluation
test results show the efficacy of adaptive distance relay over the
conventional distance relay.
Abstract: This research proposes a methodology for patent-citation-based technology input-output analysis by applying the patent information to input-output analysis developed for the dependencies among different industries. For this analysis, a technology relationship matrix and its components, as well as input and technology inducement coefficients, are constructed using patent information. Then, a technology inducement coefficient is calculated by normalizing the degree of citation from certain IPCs to the different IPCs (International patent classification) or to the same IPCs. Finally, we construct a Dependency Structure Matrix (DSM) based on the technology inducement coefficient to suggest a useful application for this methodology.
Abstract: Wind power is among the most actively developing distributed generation (DG) technology. Majority of the wind power based DG technologies employ wind turbine induction generators (WTIG) instead of synchronous generators, for the technical advantages like: reduced size, increased robustness, lower cost, and increased electromechanical damping. However, dynamic changes of wind speed make the amount of active/reactive power injected/drawn to a WTIG embedded distribution network highly variable. This paper analyzes the effect of wind speed changes on the active and reactive power penetration to the wind energy embedded distribution network. Four types of wind speed changes namely; constant, linear change, gust change and random change of wind speed are considered in the analysis. The study is carried out by three-phase, non-linear, dynamic simulation of distribution system component models. Results obtained from the investigation are presented and discussed.
Abstract: In this paper, an Interactive Compromise Approach
with Particle Swarm Optimization(ICA-PSO) is presented to solve the
Economic Emission Dispatch(EED) problem. The cost function and
emission function are modeled as the nonsmooth functions,
respectively. The bi-objective including both the minimization of cost
and emission is formulated in this paper. ICA-PSO is proposed to
solve EED problem for finding a better compromise solution. The
solution methodology can offer a global or near-global solution for
decision-making requirements. The effectiveness and efficiency of
ICA-PSO are demonstrated by a sample test system. Test results can
be shown that the proposed method provide a practical and flexible
framework for power dispatch.
Abstract: Stick models are widely used in studying the
behaviour of straight as well as skew bridges and viaducts subjected
to earthquakes while carrying out preliminary studies. The
application of such models to highly curved bridges continues to
pose challenging problems. A viaduct proposed in the foothills of the
Himalayas in Northern India is chosen for the study. It is having 8
simply supported spans @ 30 m c/c. It is doubly curved in horizontal
plane with 20 m radius. It is inclined in vertical plane as well. The
superstructure consists of a box section. Three models have been
used: a conventional stick model, an improved stick model and a 3D
finite element model. The improved stick model is employed by
making use of body constraints in order to study its capabilities. The
first 8 frequencies are about 9.71% away in the latter two models.
Later the difference increases to 80% in 50th mode. The viaduct was
subjected to all three components of the El Centro earthquake of May
1940. The numerical integration was carried out using the Hilber-
Hughes-Taylor method as implemented in SAP2000. Axial forces
and moments in the bridge piers as well as lateral displacements at
the bearing levels are compared for the three models. The maximum
difference in the axial forces and bending moments and
displacements vary by 25% between the improved and finite element
model. Whereas, the maximum difference in the axial forces,
moments, and displacements in various sections vary by 35%
between the improved stick model and equivalent straight stick
model. The difference for torsional moment was as high as 75%. It is
concluded that the stick model with body constraints to model the
bearings and expansion joints is not desirable in very sharp S curved
viaducts even for preliminary analysis. This model can be used only
to determine first 10 frequency and mode shapes but not for member
forces. A 3D finite element analysis must be carried out for
meaningful results.
Abstract: It is known that an analog Hopfield neural network
with time delay can generate the outputs which are similar to the
human electroencephalogram. To gain deeper insights into the
mechanisms of rhythm generation by the Hopfield neural networks
and to study the effects of noise on their activities, we investigated
the behaviors of the networks with symmetric and asymmetric
interneuron connections. The neural network under the study consists
of 10 identical neurons. For symmetric (fully connected) networks all
interneuron connections aij = +1; the interneuron connections for
asymmetric networks form an upper triangular matrix with non-zero
entries aij = +1. The behavior of the network is described by 10
differential equations, which are solved numerically. The results of
simulations demonstrate some remarkable properties of a Hopfield
neural network, such as linear growth of outputs, dependence of
synchronization properties on the connection type, huge
amplification of oscillation by the external uniform noise, and the
capability of the neural network to transform one type of noise to
another.
Abstract: Possible advantages of technology in educational
context required the defining boundaries of formal and informal
learning. Increasing opportunity to ubiquitous learning by
technological support has revealed a question of how to discover
the potential of individuals in the spontaneous environments such as
social networks. This seems to be related with the question of what
purposes in social networks have been being used? Social networks
provide various advantages in educational context as collaboration,
knowledge sharing, common interests, active participation and
reflective thinking. As a consequence of these, the purpose of this
study is composed of proposing a new model that could determine
factors which effect adoption of social network applications for usage
in educational context. While developing a model proposal, the
existing adoption and diffusion models have been reviewed and they
are thought to be suitable on handling an original perspective instead
of using completely other diffusion or acceptance models because of
different natures of education from other organizations. In the
proposed model; social factors, perceived ease of use, perceived
usefulness and innovativeness are determined four direct constructs
that effect adoption process. Facilitating conditions, image,
subjective norms and community identity are incorporated to model
as antecedents of these direct four constructs.
Abstract: In order to make environmental test centrifuge balance
automatically and accurately, reduce unbalance centrifugal force,
balance adjusting system of centrifuge is designed. The new balance
adjusting system comprises motor-reducer, timing belt, screw pair,
slider-guideway and four rocker force sensors. According to
information obtained by the four rocker force sensors, unbalanced
value at both ends of the big arm is computed and heavy block is
moved to achieve balance adjusting. In this paper, motor power and
torque to move the heavy block is calculated. In full load running
progress of centrifuge, the stress-strain of screw pair composed by
adjusting nut and big arm are analyzed. A successful application of the
balance adjusting system is also put forwarded. The results show that
the balance adjusting system can satisfy balance require of
environmental test centrifuge.