Abstract: In this paper, an efficient structural approach for
recognizing on-line handwritten digits is proposed. After reading
the digit from the user, the slope is estimated and normalized for
adjacent nodes. Based on the changing of signs of the slope values,
the primitives are identified and extracted. The names of these
primitives are represented by strings, and then a finite state
machine, which contains the grammars of the digits, is traced to
identify the digit. Finally, if there is any ambiguity, it will be
resolved. Experiments showed that this technique is flexible and
can achieve high recognition accuracy for the shapes of the digits
represented in this work.
Abstract: In the first part of the research work, an electrolyzer (10.16 cm dia and 24.13 cm height) to produce hydrogen and oxygen was constructed for single slice O2/H2 fuel cell using cation exchange membrane. The electrolyzer performance was tested with 23% NaOH, 30% NaOH, 30% KOH and 35% KOH electrolyte solution with current input 4 amp and 2.84 V from the rectifier. Rates of volume of hydrogen produced were 0.159 cm3/sec, 0.155 cm3/sec, 0.169 cm3/sec and 0.163 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution. Rates of volume of oxygen produced were 0.212 cm3/sec, 0.201 cm3/sec, 0.227 cm3/sec and 0.219 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution (1.5 L). In spite of being tested the increased concentration of electrolyte solution, the gas rate does not change significantly. Therefore, inexpensive 23% NaOH electrolyte solution was chosen to use as the electrolyte in the electrolyzer. In the second part of the research work, graphite serpentine flow plates, fiberglass end plates, stainless steel screen electrodes, silicone rubbers were made to assemble the single slice O2/H2 polymer electrolyte membrane fuel cell (PEMFC).
Abstract: In this paper, we present an analytical framework for the evaluation of the uplink performance of multihop cellular networks based on dynamic time division duplex (TDD). New wireless broadband protocols, such as WiMAX, WiBro, and 3G-LTE apply TDD, and mobile communication protocols under standardization (e.g., IEEE802.16j) are investigating mobile multihop relay (MMR) as a future technology. In this paper a novel MMR TDD scheme is presented, where the dynamic range of the frame is shared to traffic resources of asymmetric nature and multihop relaying. The mobile communication channel interference model comprises of inner and co-channel interference (CCI). The performance analysis focuses on the uplink due to the fact that the effects of dynamic resource allocation show significant performance degradation only in the uplink compared to time division multiple access (TDMA) schemes due to CCI [1-3], where the downlink results to be the same or better.The analysis was based on the signal to interference power ratio (SIR) outage probability of dynamic TDD (D-TDD) and TDMA systems,which are the most widespread mobile communication multi-user control techniques. This paper presents the uplink SIR outage probability with multihop results and shows that the dynamic TDD scheme applying MMR can provide a performance improvement compared to single hop applications if executed properly.
Abstract: The use of artificial neural network (ANN) modeling
for prediction and forecasting variables in water resources
engineering are being increasing rapidly. Infrastructural applications
of ANN in terms of selection of inputs, architecture of networks,
training algorithms, and selection of training parameters in different
types of neural networks used in water resources engineering have
been reported. ANN modeling conducted for water resources
engineering variables (river sediment and discharge) published in
high impact journals since 2002 to 2011 have been examined and
presented in this review. ANN is a vigorous technique to develop
immense relationship between the input and output variables, and
able to extract complex behavior between the water resources
variables such as river sediment and discharge. It can produce robust
prediction results for many of the water resources engineering
problems by appropriate learning from a set of examples. It is
important to have a good understanding of the input and output
variables from a statistical analysis of the data before network
modeling, which can facilitate to design an efficient network. An
appropriate training based ANN model is able to adopt the physical
understanding between the variables and may generate more effective
results than conventional prediction techniques.
Abstract: Nowadays, organizing a repository of documents and
resources for learning on a special field as Information Technology
(IT), together with search techniques based on domain knowledge or
document-s content is an urgent need in practice of teaching, learning
and researching. There have been several works related to methods of
organization and search by content. However, the results are still
limited and insufficient to meet user-s demand for semantic
document retrieval. This paper presents a solution for the
organization of a repository that supports semantic representation and
processing in search. The proposed solution is a model which
integrates components such as an ontology describing domain
knowledge, a database of document repository, semantic
representation for documents and a file system; with problems,
semantic processing techniques and advanced search techniques
based on measuring semantic similarity. The solution is applied to
build a IT learning materials management system of a university with
semantic search function serving students, teachers, and manager as
well. The application has been implemented, tested at the University
of Information Technology, Ho Chi Minh City, Vietnam and has
achieved good results.
Abstract: Nature conducts its action in a very private manner. To
reveal these actions classical science has done a great effort. But
classical science can experiment only with the things that can be seen
with eyes. Beyond the scope of classical science quantum science
works very well. It is based on some postulates like qubit,
superposition of two states, entanglement, measurement and
evolution of states that are briefly described in the present paper.
One of the applications of quantum computing i.e.
implementation of a novel quantum evolutionary algorithm(QEA) to
automate the time tabling problem of Dayalbagh Educational Institute
(Deemed University) is also presented in this paper. Making a good
timetable is a scheduling problem. It is NP-hard, multi-constrained,
complex and a combinatorial optimization problem. The solution of
this problem cannot be obtained in polynomial time. The QEA uses
genetic operators on the Q-bit as well as updating operator of
quantum gate which is introduced as a variation operator to converge
toward better solutions.
Abstract: The paper proposes a way of parallel processing of
SURF and Optical Flow for moving object recognition and tracking.
The object recognition and tracking is one of the most important task
in computer vision, however disadvantage are many operations cause
processing speed slower so that it can-t do real-time object recognition
and tracking. The proposed method uses a typical way of feature
extraction SURF and moving object Optical Flow for reduce
disadvantage and real-time moving object recognition and tracking,
and parallel processing techniques for speed improvement. First
analyse that an image from DB and acquired through the camera using
SURF for compared to the same object recognition then set ROI
(Region of Interest) for tracking movement of feature points using
Optical Flow. Secondly, using Multi-Thread is for improved
processing speed and recognition by parallel processing. Finally,
performance is evaluated and verified efficiency of algorithm
throughout the experiment.
Abstract: Knowledge management is a process taking any steps
that needed to get the most out of available knowledge resources.
KM involved several steps; capturing the knowledge discovering
new knowledge, sharing the knowledge and applied the knowledge in
the decision making process. In applying the knowledge, it is not
necessary for the individual that use the knowledge to comprehend it
as long as the available knowledge is used in guiding the decision
making and actions. When an expert is called and he provides stepby-
step procedure on how to solve the problems to the caller, the
expert is transferring the knowledge or giving direction to the caller.
And the caller is 'applying' the knowledge by following the
instructions given by the expert. An appropriate mechanism is
needed to ensure effective knowledge transfer which in this case is
by telephone or email. The problem with email and telephone is that
the knowledge is not fully circulated and disseminated to all users. In
this paper, with related experience of local university Help Desk, it is
proposed the usage of Information Technology (IT)to effectively
support the knowledge transfer in the organization. The issues
covered include the existing knowledge, the related works, the
methodology used in defining the knowledge management
requirements as well the overview of the prototype.
Abstract: In this article, the phenomenon of nonlinear
consolidation in saturated and homogeneous clay layer is studied.
Considering time-varied drainage model, the excess pore water
pressure in the layer depth is calculated. The Generalized Differential
Quadrature (GDQ) method is used for the modeling and numerical
analysis. For the purpose of analysis, first the domain of independent
variables (i.e., time and clay layer depth) is discretized by the
Chebyshev-Gauss-Lobatto series and then the nonlinear system of
equations obtained from the GDQ method is solved by means of the
Newton-Raphson approach. The obtained results indicate that the
Generalized Differential Quadrature method, in addition to being
simple to apply, enjoys a very high accuracy in the calculation of
excess pore water pressure.
Abstract: In this study, we explore the use of information for inventory decision in the healthcare organization (HO). We consider the scenario when the HO can make use of the information collected from some correlated products to enhance its inventory planning. Motivated by our real world observations that HOs adopt RFID and bar-coding system for information collection purpose, we examine the effectiveness of these systems for inventory planning with Bayesian information updating. We derive the optimal ordering decision and study the issue of Pareto improvement in the supply chain. Our analysis demonstrates that RFID system will outperform the bar-coding system when the RFID system installation cost and the tag cost reduce to a level that is comparable with that of the barcoding system. We also show how an appropriately set wholesale pricing contract can achieve Pareto improvement in the HO supply chain.
Abstract: Four design alternatives for lateral force-resisting
systems of tall buildings in Dubai, UAE are presented. Quantitative
comparisons between the different designs are also made. This paper
is intended to provide different feasible lateral systems to be used in
Dubai in light of the available seismic hazard studies of the UAE.
The different lateral systems are chosen in conformance with the
International Building Code (IBC). Moreover, the expected behavior
of each system is highlighted and light is shed on some of the cost
implications associated with lateral system selection.
Abstract: In this paper, we employ the approach of linear
programming to propose a new interactive broadcast method. In our
method, a film S is divided into n equal parts and broadcast via k
channels. The user simultaneously downloads these segments from k
channels into the user-s set-top-box (STB) and plays them in order.
Our method assumes that the initial p segments will not have
fast-forwarding capabilities. Every time the user wants to initiate d
times fast-forwarding, according to our broadcasting strategy, the
necessary segments already saved in the user-s STB or are just
download on time for playing. The proposed broadcasting strategy not
only allows the user to pause and rewind, but also to fast-forward.
Abstract: The scenario of bypass transition is generally described
as follows: the low-frequency disturbances in the free-stream may
generate long stream-wise streaks in the boundary layer, which later
may trigger secondary instability, leading to rapid increase of
high-frequency disturbances. Then possibly turbulent spots emerge,
and through their merging, lead to fully developed turbulence. This
description, however, is insufficient in the sense that it does not
provide the inherent mechanism of transition that during the transition,
a large number of waves with different frequencies and wave numbers
appear almost simultaneously, producing sufficiently large Reynolds
stress, so the mean flow profile can change rapidly from laminar to
turbulent. In this paper, such a mechanism will be figured out from
analyzing DNS data of transition.
Abstract: The distributions of stresses and deflection in
rectangular isotropic and orthotropic plates with central
circular hole under transverse static loading have been studied
using finite element method. The aim of author is to analyze
the effect of D/A ratio (where D is hole diameter and A is plate
width) upon stress concentration factor (SCF) and deflection
in isotropic and orthotropic plates under transverse static
loading. The D/A ratio is varied from 0.01 to 0.9. The analysis
is done for plates of isotropic and two different orthotropic
materials. The results are obtained for three different boundary
conditions. The variations of SCF and deflection with respect
to D/A ratio are presented in graphical form and discussed.
The finite element formulation is carried out in the analysis
section of the ANSYS package.
Abstract: Rapid Prototyping (RP) is a technology that produces models and prototype parts from 3D CAD model data, CT/MRI scan data, and model data created from 3D object digitizing systems. There are several RP process like Stereolithography (SLA), Solid Ground Curing (SGC), Selective Laser Sintering (SLS), Fused Deposition Modeling (FDM), 3D Printing (3DP) among them SLS and FDM RP processes are used to fabricate pattern of custom cranial implant. RP technology is useful in engineering and biomedical application. This is helpful in engineering for product design, tooling and manufacture etc. RP biomedical applications are design and development of medical devices, instruments, prosthetics and implantation; it is also helpful in planning complex surgical operation. The traditional approach limits the full appreciation of various bony structure movements and therefore the custom implants produced are difficult to measure the anatomy of parts and analyze the changes in facial appearances accurately. Cranioplasty surgery is a surgical correction of a defect in cranial bone by implanting a metal or plastic replacement to restore the missing part. This paper aims to do a comparative study on the dimensional error of CAD and SLS RP Models for reconstruction of cranial defect by comparing the virtual CAD with the physical RP model of a cranial defect.
Abstract: Uterine and oviducal fluids are necessary for
capacitation of the spermatozoa and early embryonic development.
The aim of the present study was to determine the effects of estrous
cycle phases (follicular and luteal) on some biological parameters
(enzymes, electrolytes and total proteins) in uterine and oviducal
secretions of ewes. Oviducal and uterine fluids were collected,
diluted and centrifuged. According to our results, concentrations of
GPT, G6PDH, total proteins, K and Na were significantly (P
Abstract: Over 90% of the world trade is carried by the
international shipping industry. As most of the countries are
developing, seaborne trade continues to expand to bring benefits for
consumers across the world. Studies show that world trade will
increase 70-80% through shipping in the next 15-20 years. Present
global fleet of 70000 commercial ships consumes approximately 200
million tonnes of diesel fuel a year and it is expected that it will be
around 350 million tonnes a year by 2020. It will increase the
demand for fuel and also increase the concentration of CO2 in the
atmosphere. So, it-s essential to control this massive fuel
consumption and CO2 emission. The idea is to utilize a diesel-wind
hybrid system for ship propulsion. Use of wind energy by installing
modern wing-sails in ships can drastically reduce the consumption of
diesel fuel. A huge amount of wind energy is available in oceans.
Whenever wind is available the wing-sails would be deployed and
the diesel engine would be throttled down and still the same forward
speed would be maintained. Wind direction in a particular shipping
route is not same throughout; it changes depending upon the global
wind pattern which depends on the latitude. So, the wing-sail
orientation should be such that it optimizes the use of wind energy.
We have made a computer programme in which by feeding the data
regarding wind velocity, wind direction, ship-motion direction; we
can find out the best wing-sail position and fuel saving for
commercial ships. We have calculated net fuel saving in certain
international shipping routes, for instance, from Mumbai in India to
Durban in South Africa. Our estimates show that about 8.3% diesel
fuel can be saved by utilizing the wind. We are also developing an
experimental model of the ship employing airfoils (small scale wingsail)
and going to test it in National Wind Tunnel Facility in IIT
Kanpur in order to develop a control mechanism for a system of
airfoils.
Abstract: Software projects are very dynamic and require
recurring adjustments of their project plans. These settings can be
understood as reconfigurations in the schedule, in the resources
allocation and other design elements. Yet, during the planning and
execution of a software project, the integration of specific activities
in the projects with the activities that take part in the organization-s
common activity flow should be considered. This article presents the
results from a systematic review of aspects related to software
projects- dynamic reconfiguration emphasizing the integration of
project management with the organizational flows. A series of studies
was analyzed from the year 2000 to the present. The results of this
work show that there is a diversity of techniques and strategies for
dynamic reconfiguration of software projects-. However, few
approaches consider the integration of software project activities with
the activities that take part in the organization-s common workflow.
Abstract: An attractor neural network on the small-world topology
is studied. A learning pattern is presented to the network, then
a stimulus carrying local information is applied to the neurons and
the retrieval of block-like structure is investigated. A synaptic noise
decreases the memory capability. The change of stability from local
to global attractors is shown to depend on the long-range character
of the network connectivity.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.