Abstract: The calculation of buckling length factor (K) for steel
frames columns is a major and governing processes to determine the
dimensions steel frame columns cross sections during design. The
buckling length of steel frames columns has a direct effect on the cost
(weight) of using cross section. A new formula is required to
determine buckling length factor (K) by simplified way. In this
research a new formula for buckling length factor (K) was established
to determine by accurate method for a limited interval of columns
ends rigidity (GA, GB). The new formula can be used ease to
evaluate the buckling length factor without needing to complicated
equations or difficult charts.
Abstract: The plastic flow of metal in the extrusion process is
an important factor in controlling the mechanical properties of the
extruded products. It is, however, difficult to predict the metal flow
in three dimensional extrusions of sections due to the involvement of
re-entrant corners. The present study is to find an upper bound
solution for the extrusion of triangular sectioned through taper dies
from round sectioned billet. A discontinuous kinematically
admissible velocity field (KAVF) is proposed. From the proposed
KAVF, the upper bound solution on non-dimensional extrusion
pressure is determined with respect to the chosen process parameters.
The theoretical results are compared with experimental results to
check the validity of the proposed velocity field. An extrusion setup
is designed and fabricated for the said purpose, and all extrusions are
carried out using circular billets. Experiments are carried out with
commercially available lead at room temperature.
Abstract: Molar excess Volumes, VE ijk and speeds of sound , uijk of 2-pyrrolidinone (i) + benzene or toluene (j) + ethanol (k) ternary mixture have been measured as a function of composition at 308.15 K. The observed speeds of sound data have been utilized to determine excess isentropic compressiblities, ( E S κ )ijk of ternary (i + j + k) mixtures. Molar excess volumes, VE ijk and excess isentropic compressibilities, ( E S κ )ijk data have fitted to the Redlich-Kister equation to calculate ternary adjustable parameters and standard deviations. The Moelywn-Huggins concept (Huggins in Polymer 12: 389-399, 1971) of connectivity between the surfaces of the constituents of binary mixtures has been extended to ternary mixtures (using the concept of a connectivity parameter of third degree of molecules, 3ξ , which inturn depends on its topology) to obtain an expression that describes well the measured VE ijk and ( E S κ )ijk data.
Abstract: In this study concept of experimental design is
successfully applied for the determination of optimum condition to
produce PP/SWCNT (Polypropylene/Single wall carbon nanotube)
nanocomposite. Central composite design as one of experimental
design techniques is employed for the optimization and statistical
determination of the significant factors influencing on the tensile
modulus and yield stress as mechanical properties of this
nanocomposite. The significant factors are SWCNT weight fraction
and acid treatment time for functionalizing the nanoparticles.
Optimum conditions are in 0.7 % of SWCNT weight fraction and 210
min as acid treatment time for 1112.75 ± 28 MPa as maximum tensile
modulus and in 216 min and 0.65 % as acid treatment time and
SWCNT weight fraction respectively for 40.26 ± 0.3 MPa as
maximum yield stress. Also after setting new experiments for test
these optimum conditions, found excelent agreement with predicted
values.
Abstract: Virtual environment induces simulator sickness effect
for some users. The purpose of this research is to compare the
simulation sickness relative with parallax affect in one-screen and
three-screen HoloStageTM system, measured by Simulation Sickness
Questionnaire (SSQ). The results show the subjects tested in
three-screen has less sickness than one-screen and effect from the
Oculomotor (O) more than from the Disorientation (D) and more than
from the Nausea (N) or represented in O>D>N.
Abstract: This paper reports on a receding horizon filtering for
mobile robot systems with cross-correlated sensor noises and
uncertainties. Also, the effect of uncertain parameters in the state of
the tracking error model performance is considered. A distributed
fusion receding horizon filter is proposed. The distributed fusion
filtering algorithm represents the optimal linear combination of the
local filters under the minimum mean square error criterion. The
derivation of the error cross-covariances between the local receding
horizon filters is the key of this paper. Simulation results of the
tracking mobile robot-s motion demonstrate high accuracy and
computational efficiency of the distributed fusion receding horizon
filter.
Abstract: To evaluate genetic variation of wheat (Triticum aestivum) affected by heat and drought stress on eight Australian wheat genotypes that are parents of Doubled Haploid (HD) mapping populations at the vegetative stage, the water stress experiment was conducted at 65% field capacity in growth room. Heat stress experiment was conducted in the research field under irrigation over summer. Result show that water stress decreased dry shoot weight and RWC but increased osmolarity and means of Fv/Fm values in all varieties except for Krichauff. Krichauff and Kukri had the maximum RWC under drought stress. Trident variety was shown maximum WUE, osmolarity (610 mM/Kg), dry mater, quantum yield and Fv/Fm 0.815 under water stress condition. However, the recovery of quantum yield was apparent between 4 to 7 days after stress in all varieties. Nevertheless, increase in water stress after that lead to strong decrease in quantum yield. There was a genetic variation for leaf pigments content among varieties under heat stress. Heat stress decreased significantly the total chlorophyll content that measured by SPAD. Krichauff had maximum value of Anthocyanin content (2.978 A/g FW), chlorophyll a+b (2.001 mg/g FW) and chlorophyll a (1.502 mg/g FW). Maximum value of chlorophyll b (0.515 mg/g FW) and Carotenoids (0.234 mg/g FW) content belonged to Kukri. The quantum yield of all varieties decreased significantly, when the weather temperature increased from 28 ÔùªC to 36 ÔùªC during the 6 days. However, the recovery of quantum yield was apparent after 8th day in all varieties. The maximum decrease and recovery in quantum yield was observed in Krichauff. Drought and heat tolerant and moderately tolerant wheat genotypes were included Trident, Krichauff, Kukri and RAC875. Molineux, Berkut and Excalibur were clustered into most sensitive and moderately sensitive genotypes. Finally, the results show that there was a significantly genetic variation among the eight varieties that were studied under heat and water stress.
Abstract: Adaptive control involves modifying the control law
used by the controller to cope with the fact that the parameters of the
system being controlled change drastically due to change in
environmental conditions or in system itself. This technique is based
on the fundamental characteristic of adaptation of living organism.
The adaptive control process is one that continuously and
automatically measures the dynamic behavior of plant, compares it
with the desired output and uses the difference to vary adjustable
system parameters or to generate an actuating signal in such a way so
that optimal performance can be maintained regardless of system
changes. This paper deals with application of model reference
adaptive control scheme in first order system. The rule which is used
for this application is MIT rule. This paper also shows the effect of
adaptation gain on the system performance. Simulation is done in
MATLAB and results are discussed in detail.
Abstract: In this paper a new embedded Singly Diagonally
Implicit Runge-Kutta Nystrom fourth order in fifth order method for
solving special second order initial value problems is derived. A
standard set of test problems are tested upon and comparisons on the
numerical results are made when the same set of test problems are
reduced to first order systems and solved using the existing
embedded diagonally implicit Runge-Kutta method. The results
suggests the superiority of the new method.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: The fault detection and diagnosis of complicated
production processes is one of essential tasks needed to run the process
safely with good final product quality. Unexpected events occurred in
the process may have a serious impact on the process. In this work,
triangular representation of process measurement data obtained in an
on-line basis is evaluated using simulation process. The effect of using
linear and nonlinear reduced spaces is also tested. Their diagnosis
performance was demonstrated using multivariate fault data. It has
shown that the nonlinear technique based diagnosis method produced
more reliable results and outperforms linear method. The use of
appropriate reduced space yielded better diagnosis performance. The
presented diagnosis framework is different from existing ones in that it
attempts to extract the fault pattern in the reduced space, not in the
original process variable space. The use of reduced model space helps
to mitigate the sensitivity of the fault pattern to noise.
Abstract: In this paper, estimation of the linear regression
model is made by ordinary least squares method and the
partially linear regression model is estimated by penalized
least squares method using smoothing spline. Then, it is
investigated that differences and similarity in the sum of
squares related for linear regression and partial linear
regression models (semi-parametric regression models). It is
denoted that the sum of squares in linear regression is reduced
to sum of squares in partial linear regression models.
Furthermore, we indicated that various sums of squares in the
linear regression are similar to different deviance statements in
partial linear regression. In addition to, coefficient of the
determination derived in linear regression model is easily
generalized to coefficient of the determination of the partial
linear regression model. For this aim, it is made two different
applications. A simulated and a real data set are considered to
prove the claim mentioned here. In this way, this study is
supported with a simulation and a real data example.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: A thin layer on the component surface can be found
with high tensile residual stresses, due to turning operations, which
can dangerously affect the fatigue performance of the component. In
this paper an analytical approach is presented to reconstruct the
residual stress field from a limited incomplete set of measurements.
Airy stress function is used as the primary unknown to directly solve
the equilibrium equations and satisfying the boundary conditions. In
this new method there exists the flexibility to impose the physical
conditions that govern the behavior of residual stress to achieve a
meaningful complete stress field. The analysis is also coupled to a
least squares approximation and a regularization method to provide
stability of the inverse problem. The power of this new method is
then demonstrated by analyzing some experimental measurements
and achieving a good agreement between the model prediction and
the results obtained from residual stress measurement.
Abstract: This paper presents the application of a signal intensity independent registration criterion for non-rigid body registration of medical images. The criterion is defined as the weighted ratio image of two images. The ratio is computed on a voxel per voxel basis and weighting is performed by setting the ratios between signal and background voxels to a standard high value. The mean squared value of the weighted ratio is computed over the union of the signal areas of the two images and it is minimized using the Chebyshev polynomial approximation. The geometric transformation model adopted is a local cubic B-splines based model.
Abstract: To investigates the effect of fiberglass clamping
process improvement on drape simulation prediction. This has
great effect on the mould and the fiber during manufacturing
process. This also, improves the fiber strain, the quality of the
fiber orientation in the area of folding and wrinkles formation
during the press-forming process. Drape simulation software
tool was used to digitalize the process, noting the formation
problems on the contour sensitive part. This was compared
with the real life clamping processes using single and double
frame set-ups to observe the effects. Also, restrains are
introduced by using clips, and the G-clamps with predetermine
revolution to; restrain the fabric deformation during the
forming process.The incorporation of clamping and fabric
restrain deformation improved on the prediction of the
simulation tool. Therefore, for effective forming process,
incorporation of clamping process into the drape simulation
process will assist in the development of fiberglass application
in manufacturing process.
Abstract: Image coding based on clustering provides immediate
access to targeted features of interest in a high quality decoded
image. This approach is useful for intelligent devices, as well as for
multimedia content-based description standards. The result of image
clustering cannot be precise in some positions especially on pixels
with edge information which produce ambiguity among the clusters.
Even with a good enhancement operator based on PDE, the quality of
the decoded image will highly depend on the clustering process. In
this paper, we introduce an ambiguity cluster in image coding to
represent pixels with vagueness properties. The presence of such
cluster allows preserving some details inherent to edges as well for
uncertain pixels. It will also be very useful during the decoding phase
in which an anisotropic diffusion operator, such as Perona-Malik,
enhances the quality of the restored image. This work also offers a
comparative study to demonstrate the effectiveness of a fuzzy
clustering technique in detecting the ambiguity cluster without losing
lot of the essential image information. Several experiments have been
carried out to demonstrate the usefulness of ambiguity concept in
image compression. The coding results and the performance of the
proposed algorithms are discussed in terms of the peak signal-tonoise
ratio and the quantity of ambiguous pixels.
Abstract: Basic ingredients of concrete are cement, fine aggregate, coarse aggregate and water. To produce a concrete of certain specific properties, optimum proportion of these ingredients are mixed. The important factors which govern the mix design are grade of concrete, type of cement and size, shape and grading of aggregates. Concrete mix design method is based on experimentally evolved empirical relationship between the factors in the choice of mix design. Basic draw backs of this method are that it does not produce desired strength, calculations are cumbersome and a number of tables are to be referred for arriving at trial mix proportion moreover, the variation in attainment of desired strength is uncertain below the target strength and may even fail. To solve this problem, a lot of cubes of standard grades were prepared and attained 28 days strength determined for different combination of cement, fine aggregate, coarse aggregate and water. An artificial neural network (ANN) was prepared using these data. The input of ANN were grade of concrete, type of cement, size, shape and grading of aggregates and output were proportions of various ingredients. With the help of these inputs and outputs, ANN was trained using feed forward back proportion model. Finally trained ANN was validated, it was seen that it gave the result with/ error of maximum 4 to 5%. Hence, specific type of concrete can be prepared from given material properties and proportions of these materials can be quickly evaluated using the proposed ANN.
Abstract: This paper presents the results of enhancing images from a left and right stereo pair in order to increase the resolution of a 3D representation of a scene generated from that same pair. A new neural network structure known as a Self Delaying Dynamic Network (SDN) has been used to perform the enhancement. The advantage of SDNs over existing techniques such as bicubic interpolation is their ability to cope with motion and noise effects. SDNs are used to generate two high resolution images, one based on frames taken from the left view of the subject, and one based on the frames from the right. This new high resolution stereo pair is then processed by a disparity map generator. The disparity map generated is compared to two other disparity maps generated from the same scene. The first is a map generated from an original high resolution stereo pair and the second is a map generated using a stereo pair which has been enhanced using bicubic interpolation. The maps generated using the SDN enhanced pairs match more closely the target maps. The addition of extra noise into the input images is less problematic for the SDN system which is still able to out perform bicubic interpolation.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.