Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: Discovering new biological knowledge from the highthroughput biological data is a major challenge to bioinformatics today. To address this challenge, we developed a new approach for protein classification. Proteins that are evolutionarily- and thereby functionally- related are said to belong to the same classification. Identifying protein classification is of fundamental importance to document the diversity of the known protein universe. It also provides a means to determine the functional roles of newly discovered protein sequences. Our goal is to predict the functional classification of novel protein sequences based on a set of features extracted from each protein sequence. The proposed technique used datasets extracted from the Structural Classification of Proteins (SCOP) database. A set of spectral domain features based on Fast Fourier Transform (FFT) is used. The proposed classifier uses multilayer back propagation (MLBP) neural network for protein classification. The maximum classification accuracy is about 91% when applying the classifier to the full four levels of the SCOP database. However, it reaches a maximum of 96% when limiting the classification to the family level. The classification results reveal that spectral domain contains information that can be used for classification with high accuracy. In addition, the results emphasize that sequence similarity measures are of great importance especially at the family level.
Abstract: In this paper an approaches for increasing the
effectiveness of error detection in computer network channels with
Pulse-Amplitude Modulation (PAM) has been proposed. Proposed
approaches are based on consideration of special feature of errors,
which are appearances in line with PAM. The first approach consists
of CRC modification specifically for line with PAM. The second
approach is base of weighted checksums using. The way for
checksum components coding has been developed. It has been shown
that proposed checksum modification ensure superior digital data
control transformation reliability for channels with PAM in compare
to CRC.
Abstract: This paper proposes a set of quasi-static mathematical
model of magnetic fields caused by high voltage conductors of
distribution transformer by using a set of second-order partial
differential equation. The modification for complex magnetic field
analysis and time-harmonic simulation are also utilized. In this
research, transformers were study in both balanced and unbalanced
loading conditions. Computer-based simulation utilizing the threedimensional
finite element method (3-D FEM) is exploited as a tool
for visualizing magnetic fields distribution volume a distribution
transformer. Finite Element Method (FEM) is one among popular
numerical methods that is able to handle problem complexity in
various forms. At present, the FEM has been widely applied in most
engineering fields. Even for problems of magnetic field distribution,
the FEM is able to estimate solutions of Maxwell-s equations
governing the power transmission systems. The computer simulation
based on the use of the FEM has been developed in MATLAB
programming environment.
Abstract: This paper describes a new measuring algorithm for
three-dimensional (3-D) braided composite material .Braided angle is
an important parameter of braided composites. The objective of this
paper is to present an automatic measuring system. In the paper, the
algorithm is performed by using vcµ6.0 language on PC. An
advanced filtered algorithm for image of 3-D braided composites
material performs has been developed. The procedure is completely
automatic and relies on the gray scale information content of the
images and their local wavelet transform modulus maxims.
Experimental results show that the proposed method is feasible.
The algorithm was tested on both carbon-fiber and glass-fiber
performs.
Abstract: In this paper we study the transformation of Euler equations 1 , u u u Pf t (ρ ∂) + ⋅∇ = − ∇ + ∂ G G G G ∇⋅ = u 0, G where (ux, t) G G is the velocity of a fluid, P(x, t) G is the pressure of a fluid andρ (x, t) G is density. First of all, we rewrite the Euler equations in terms of new unknown functions. Then, we introduce new independent variables and transform it to a new curvilinear coordinate system. We obtain the Euler equations in the new dependent and independent variables. The governing equations into two subsystems, one is hyperbolic and another is elliptic.
Abstract: The use of magnetic and magnetic/gold core/shell
nanoparticles in biotechnology or medicine has shown good promise
due to their hybrid nature which possesses superior magnetic and
optical properties. Some of these potential applications include
hyperthermia treatment, bio-separations, diagnostics, drug delivery
and toxin removal. Synthesis refinement to control geometric and
magnetic/optical properties, and finding functional surfactants for
biomolecular attachment, are requirements to meet application
specifics.
Various high-temperature preparative methods were used for the
synthesis of iron oxide and gold-coated iron oxide nanoparticles.
Different surface functionalities, such as 11-aminoundecanoic and
11-mercaptoundecanoic acid, were introduced on the surface of the
particles to facilitate further attachment of biomolecular functionality
and drug-like molecules. Nanoparticle thermal stability, composition,
state of aggregation, size and morphology were investigated and the
results from techniques such as Fourier Transform-Infra Red
spectroscopy (FT-IR), Ultraviolet visible spectroscopy (UV-vis),
Transmission Electron Microscopy (TEM) and thermal analysis are
discussed.
Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: Because of excellent properties, people has paid more
attention to SPIHI algorithm, which is based on the traditional wavelet
transformation theory, but it also has its shortcomings. Combined the
progress in the present wavelet domain and the human's visual
characteristics, we propose an improved algorithm based on human
visual characteristics of SPIHT in the base of analysis of SPIHI
algorithm. The experiment indicated that the coding speed and quality
has been enhanced well compared to the original SPIHT algorithm,
moreover improved the quality of the transmission cut off.
Abstract: Motor imagery classification provides an important basis for designing Brain Machine Interfaces [BMI]. A BMI captures and decodes brain EEG signals and transforms human thought into actions. The ability of an individual to control his EEG through imaginary mental tasks enables him to control devices through the BMI. This paper presents a method to design a four state BMI using EEG signals recorded from the C3 and C4 locations. Principle features extracted through principle component analysis of the segmented EEG are analyzed using two novel classification algorithms using Elman recurrent neural network and functional link neural network. Performance of both classifiers is evaluated using a particle swarm optimization training algorithm; results are also compared with the conventional back propagation training algorithm. EEG motor imagery recorded from two subjects is used in the offline analysis. From overall classification performance it is observed that the BP algorithm has higher average classification of 93.5%, while the PSO algorithm has better training time and maximum classification. The proposed methods promises to provide a useful alternative general procedure for motor imagery classification
Abstract: Model Predictive Control (MPC) is increasingly being
proposed for real time applications and embedded systems. However
comparing to PID controller, the implementation of the MPC in
miniaturized devices like Field Programmable Gate Arrays (FPGA)
and microcontrollers has historically been very small scale due to its
complexity in implementation and its computation time requirement.
At the same time, such embedded technologies have become an
enabler for future manufacturing enterprises as well as a transformer
of organizations and markets. Recently, advances in microelectronics
and software allow such technique to be implemented in embedded
systems. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and
applied control technique in the industrial engineering. In fact in
this paper, we propose an efficient framework for implementation
of Generalized Predictive Control (GPC) in the performed STM32
microcontroller. The STM32 keil starter kit based on a JTAG interface
and the STM32 board was used to implement the proposed GPC
firmware. Besides the GPC, the PID anti windup algorithm was
also implemented using Keil development tools designed for ARM
processor-based microcontroller devices and working with C/Cµ
langage. A performances comparison study was done between both
firmwares. This performances study show good execution speed and
low computational burden. These results encourage to develop simple
predictive algorithms to be programmed in industrial standard hardware.
The main features of the proposed framework are illustrated
through two examples and compared with the anti windup PID
controller.
Abstract: The application of a simple microcontroller to deal
with a three variable input and a single output fuzzy logic controller,
with Proportional – Integral – Derivative (PID) response control
built-in has been tested for an automatic voltage regulator. The
fuzzifiers are based on fixed range of the variables of output voltage.
The control output is used to control the wiper motor of the auto
transformer to adjust the voltage, using fuzzy logic principles, so that
the voltage is stabilized. In this report, the author will demonstrate
how fuzzy logic might provide elegant and efficient solutions in the
design of multivariable control based on experimental results rather
than on mathematical models.
Abstract: In this paper, we propose a fully-utilized, block-based 2D DWT (discrete wavelet transform) architecture, which consists of four 1D DWT filters with two-channel QMF lattice structure. The proposed architecture requires about 2MN-3N registers to save the intermediate results for higher level decomposition, where M and N stand for the filter length and the row width of the image respectively. Furthermore, the proposed 2D DWT processes in horizontal and vertical directions simultaneously without an idle period, so that it computes the DWT for an N×N image in a period of N2(1-2-2J)/3. Compared to the existing approaches, the proposed architecture shows 100% of hardware utilization and high throughput rates. To mitigate the long critical path delay due to the cascaded lattices, we can apply the pipeline technique with four stages, while retaining 100% of hardware utilization. The proposed architecture can be applied in real-time video signal processing.
Abstract: The development of entrepreneurial competences of
farmers has been pointed out as a necessary condition for the
modernization of land in facing the phenomenon of globalization.
However, the educational processes involved in such a development
have been studied little, especially in emerging economies. This
research aims to enlighten some of the critical issues behind the early
stages of the transformation of farmers into entrepreneurs, through in
depth interviews with farmers, entrepreneurial promoters and public
officials participating in a public pilot project in Mexico. Although
major impacts were expected only in the long run, important positive
changes in the mind set of farmers and other participants were found
in early stages of the intervention. Apparently, the farmers started a
process of becoming more conscious about the importance of
preserving the aquiferous resources, as well as more market and
entrepreneurial oriented.
Abstract: The condition of lightning surge causes the traveling waves and the temporary increase in voltage in the transmission line system. Lightning is the most harmful for destroying the transmission line and setting devices so it is necessary to study and analyze the temporary increase in voltage for designing and setting the surge arrester. This analysis describes the figure of the lightning wave in transmission line with 115 kV voltage level in Thailand by using ATP/EMTP program to create the model of the transmission line and lightning surge. Because of the limit of this program, it must be calculated for the geometry of the transmission line and surge parameter and calculation in the manual book for the closest value of the parameter. On the other hand, for the effects on surge protector when the lightning comes, the surge arrester model must be right and standardized as metropolitan electrical authority's standard. The candidate compared the real information to the result from calculation, also. The results of the analysis show that the temporary increase in voltage value will be rise to 326.59 kV at the line which is done by lightning when the surge arrester is not set in the system. On the other hand, the temporary increase in voltage value will be 182.83 kV at the line which is done by lightning when the surge arrester is set in the system and the period of the traveling wave is reduced, also. The distance for setting the surge arrester must be as near to the transformer as possible. Moreover, it is necessary to know the right distance for setting the surge arrester and the size of the surge arrester for preventing the temporary increase in voltage, effectively.
Abstract: A computer model of Quantum Theory (QT) has been
developed by the author. Major goal of the computer model was
support and demonstration of an as large as possible scope of QT.
This includes simulations for the major QT (Gedanken-) experiments
such as, for example, the famous double-slit experiment.
Besides the anticipated difficulties with (1) transforming exacting
mathematics into a computer program, two further types of problems
showed up, namely (2) areas where QT provides a complete mathematical
formalism, but when it comes to concrete applications the
equations are not solvable at all, or only with extremely high effort;
(3) QT rules which are formulated in natural language and which do
not seem to be translatable to precise mathematical expressions, nor
to a computer program.
The paper lists problems in all three categories and describes also
the possible solutions or circumventions developed for the computer
model.
Abstract: In this work a new method for low complexity
image coding is presented, that permits different settings and great
scalability in the generation of the final bit stream. This coding
presents a continuous-tone still image compression system that
groups loss and lossless compression making use of finite arithmetic
reversible transforms. Both transformation in the space of color and
wavelet transformation are reversible. The transformed coefficients
are coded by means of a coding system in depending on a
subdivision into smaller components (CFDS) similar to the bit
importance codification. The subcomponents so obtained are
reordered by means of a highly configure alignment system
depending on the application that makes possible the re-configure of
the elements of the image and obtaining different importance levels
from which the bit stream will be generated. The subcomponents of
each importance level are coded using a variable length entropy
coding system (VBLm) that permits the generation of an embedded
bit stream. This bit stream supposes itself a bit stream that codes a
compressed still image. However, the use of a packing system on the
bit stream after the VBLm allows the realization of a final highly
scalable bit stream from a basic image level and one or several
improvement levels.
Abstract: This research proposes a Preemptive Possibilistic
Linear Programming (PPLP) approach for solving multiobjective
Aggregate Production Planning (APP) problem with interval demand
and imprecise unit price and related operating costs. The proposed
approach attempts to maximize profit and minimize changes of
workforce. It transforms the total profit objective that has imprecise
information to three crisp objective functions, which are maximizing
the most possible value of profit, minimizing the risk of obtaining the
lower profit and maximizing the opportunity of obtaining the higher
profit. The change of workforce level objective is also converted.
Then, the problem is solved according to objective priorities. It is
easier than simultaneously solve the multiobjective problem as
performed in existing approach. Possible range of interval demand is
also used to increase flexibility of obtaining the better production
plan. A practical application of an electronic company is illustrated to
show the effectiveness of the proposed model.
Abstract: One way for optimum loading of overdimensioning
conveyers is speed (capacity) decrement, with attention for
production capabilities and demands. At conveyers which drives with
three phase slip-ring induction motor, technically reasonable solution
for conveyer (driving motors) speed regulation is using constant
torque subsynchronous cascade with static semiconductor converter
and transformer for energy reversion to the power network. In the
paper is described mathematical model for parameter calculation of
two-motors 6 kV subsynchronous cascade. It is also demonstrated
that applying of this cascade gave several good properties, foremost
in electrical energy saving, also in improving of other energy
indexes, and finally that results in cost reduction of complete
electrical motor drive.
Abstract: The paper outlines the relevance of computational
geometry within the design and production process of architecture.
Based on two case studies, the digital chain - from the initial formfinding
to the final realization of spatial concepts - is discussed in
relation to geometric principles. The association with the fascinating
complexity that can be found in nature and its underlying geometry
was the starting point for both projects presented in the paper. The
translation of abstract geometric principles into a three-dimensional
digital design model – realized in Rhinoceros – was followed by a
process of transformation and optimization of the initial shape that
integrated aesthetic, spatial and structural qualities as well as aspects
of material properties and conditions of production.