Abstract: Green house effect has becomes a serious concern in
many countries due to the increase consumption of the fossil fuel.
There have been many studies to find an alternative power source.
Wind energy found to be one of the most useful solutions to help in
overcoming the air pollution and global. There is no agreed solution
to conversion of wind energy to electrical energy. In this paper, the
advantages of using a Switched Reluctance Generator (SRG) for
wind energy applications. The theoretical study of the self excitation
of a SRG and the determination of the variable parameters in a SRG
design are discussed. The design parameters for the maximum power
output of the SRG are computed using Matlab simulation. The
designs of the circuit to control the variable parameters in a SRG to
provide the maximum power output are also discussed.
Abstract: An experimental study of anaerobic treatment was performed by hybrid upflow anaerobic sludge blanket (HUASB) reactor to treat produced water (PW) of an onshore crude oil terminal (COD: 1597 mg/L, NH3-N: 14.7 mg/L, phenol: 13.8 mg/L, BOD5: 862 mg/L, sodium: 6240 mg/L and chloride 9530 mg/L). The produced water with high salinity and other toxic substances will inhibit the methanogens performance if there is no adaptation on biomass before anaerobic digestion. COD removal from produced water was investigated at five different dilutions of produced water and tap water (TW) without any nutrient addition and pre-treatment. The dilution ratios were 1PW:4TW, 2PW:3TW, 3PW:2TW, 4PW:1TW and 5PW:0TW. The reactor was evaluated at mesophilic operating condition (35 ± 2 °C) at 5 days of HRT for 250 days continuous feed. The average COD removals for 1PW:4TW, 2PW:3TW, 3PW:2TW, 4PW:1TW and 5PW:0TW were found to be approximately 76.1%, 73.8%, 70.3%, 46.3% and 61.82% respectively, with final average effluent COD of 123.7 mg/L, 240 mg/L, 294 mg/L, 589 mg/L and 738 mg/L, respectively.
Abstract: The charge-pump circuit is an important component in a phase-locked loop (PLL). The charge-pump converts Up and Down signals from the phase/frequency detector (PFD) into current. A conventional CMOS charge-pump circuit consists of two switched current sources that pump charge into or out of the loop filter according to two logical inputs. The mismatch between the charging current and the discharging current causes phase offset and reference spurs in a PLL. We propose a new charge-pump circuit to reduce the current mismatch by using a regulated cascode circuit. The proposed charge-pump circuit is designed and simulated by spectre with TSMC 0.18-μm 1.8-V CMOS technology.
Abstract: The amounts of radioactivity in the igneous rocks
have been investigated; samples were collected from the total of eight
basalt rock types in the northeastern of Kurdistan region/Iraq. The
activity concentration of 226Ra (238U) series, 228Ac (232Th) series, 40K
and 137Cs were measured using Planar HPGe and NaI(Tl) detectors.
Along the study area the radium equivalent activities Raeq in Bq/Kg
of samples under investigation were found in the range of 22.16 to
77.31 Bq/Kg with an average value of 44.8 Bq/Kg, this value is much
below the internationally accepted value of 370 Bq/Kg. To estimate
the health effects of this natural radioactive composition, the average
values of absorbed gamma dose rate D (55 nGyh-1), Indoor and
outdoor annual effective dose rates Eied (0.11 mSvy-1) . and Eoed
(0.03 mSvy-1), External hazard index Hex (0.138) and internal hazard
index Hin(0.154), and representative level index Iγr (0.386) have been
calculated and found to be lower than the worldwide average values.
Abstract: Fake finger submission attack is a major problem in fingerprint recognition systems. In this paper, we introduce an aliveness detection method based on multiple static features, which derived from a single fingerprint image. The static features are comprised of individual pore spacing, residual noise and several first order statistics. Specifically, correlation filter is adopted to address individual pore spacing. The multiple static features are useful to reflect the physiological and statistical characteristics of live and fake fingerprint. The classification can be made by calculating the liveness scores from each feature and fusing the scores through a classifier. In our dataset, we compare nine classifiers and the best classification rate at 85% is attained by using a Reduced Multivariate Polynomial classifier. Our approach is faster and more convenient for aliveness check for field applications.
Abstract: The increasing usage of antibiotics in the animal
farming industry is an emerging worldwide problem contributing to
the development of antibiotic resistance. The purpose of this work was
to investigate the prevalence and antibiotic resistance profile of
bacterial isolates collected from aquatic environments and meats in a
peri-urban community in Daejeon, Korea. In an antibacterial
susceptibility test, the bacterial isolates showed a high incidence of
resistance (~ 26.04 %) to cefazolin, tetracycline, gentamycin,
norfloxacin, erythromycin and vancomycin. The results from a test for
multiple antibiotic resistance indicated that the isolates were
displaying an approximately 5-fold increase in the incidence of
multiple antibiotic resistance to combinations of two different
antibiotics compared to combinations of three or more antibiotics.
Most of the isolates showed multi-antibiotic resistance, and the
resistance patterns were similar among the sampling groups.
Sequencing data analysis of 16S rRNA showed that most of the
resistant isolates appeared to be dominated by the classes
Betaproteobacteria and Gammaproteobacteria in the phylum
Proteobacteria.
Abstract: This paper aims at developing a multilevel fuzzy
decision support model for urban rail transit planning schemes in
China under the background that China is presently experiencing an
unprecedented construction of urban rail transit. In this study, an
appropriate model using multilevel fuzzy comprehensive evaluation
method is developed. In the decision process, the followings are
considered as the influential objectives: traveler attraction,
environment protection, project feasibility and operation. In addition,
consistent matrix analysis method is used to determine the weights
between objectives and the weights between the objectives-
sub-indictors, which reduces the work caused by repeated
establishment of the decision matrix on the basis of ensuring the
consistency of decision matrix. The application results show that
multilevel fuzzy decision model can perfectly deal with the
multivariable and multilevel decision process, which is particularly
useful in the resolution of multilevel decision-making problem of
urban rail transit planning schemes.
Abstract: According to FDA (Food and Drug Administration of the United States), vinegar is definedas a sour liquid containing at least 4 grams acetic acid in 100 cubic centimeter (4% solution of acetic acid) of solution that is produced from sugary materials by alcoholic fermentation. In the base of microbial starters, vinegars could be contained of more than 50 types of volatile and aromatic substances that responsible for their sweet taste and smelling. Recently the vinegar industry has a great proportion in agriculture, food and microbial biotechnology. The acetic acid bacteria are from the family Acetobacteraceae. Regarding to the latest version of Bergy-s Mannual of Systematic Bacteriology that has categorized bacteria in the base of their 16s RNA differences, the most important acetic acid genera are included Acetobacter (genus I), Gluconacetobacter (genus VIII) and Gluconobacter (genus IX). The genus Acetobacter that is primarily used in vinegar manufacturing plants is a gram negative, obligate aerobe coccus or rod shaped bacterium with the size 0.6 - 0.8 X 1.0 - 4.0 μm, nonmotile or motile with peritrichous flagella and catalase positive – oxidase negative biochemically. Some strains are overoxidizer that could convert acetic acid to carbon dioxide and water.In this research one Acetobacter native strain with high acetic acid productivity was isolated from Iranian white – red cherry. We used two specific culture media include Carr medium [yeast extract, 3%; ethanol, 2% (v/v); bromocresol green, 0.002%; agar, 2% and distilled water, 1000 ml], Frateur medium [yeast extract, 10 g/l; CaCO3, 20 g/l; ethanol, 20 g/l; agar, 20 g/l and distilled water, 1000 ml] and an industrial culture medium. In addition to high acetic acid production and high growth rate, this strain had a good tolerance against ethanol concentration that was examined using modified Carr media with 5%, 7% and 9% ethanol concentrations. While the industrial strains of acetic acid bacteria grow in the thermal range of 28 – 30 °C, this strain was adapted for growth in 34 – 36 °C after 96 hours incubation period. These dramatic characteristics suggest a potential biotechnological strain in production of cherry vinegar with a sweet smell and different nutritional properties in comparison to recent vinegar types. The lack of growth after 24, 48 and 72 hours incubation at 34 – 36 °C and the growth after 96 hours indicates a good and fast thermal flexibility of this strain as a significant characteristic of biotechnological and industrial strains.
Abstract: Fluid flow and heat transfer of vertical full cone
embedded in porous media is studied in this paper. Nonlinear
differential equation arising from similarity solution of inverted cone
(subjected to wall temperature boundary conditions) embedded in
porous medium is solved using a hybrid neural network- particle
swarm optimization method.
To aim this purpose, a trial solution of the differential equation is
defined as sum of two parts. The first part satisfies the initial/
boundary conditions and does contain an adjustable parameter and
the second part which is constructed so as not to affect the
initial/boundary conditions and involves adjustable parameters (the
weights and biases) for a multi-layer perceptron neural network.
Particle swarm optimization (PSO) is applied to find adjustable
parameters of trial solution (in first and second part). The obtained
solution in comparison with the numerical ones represents a
remarkable accuracy.
Abstract: Thyroid cancer-s overall contribution to the
worldwide cancer burden is relatively small, but incidence rates have increased over the last three decades throughout the world. This trend has been hypothesised to reflect a combination of technological advances enabling increased detection, but also changes in
environmental factors, including population exposure to ionising radiation from fallout, diagnostic tests and treatment for benign and
malignant conditions. The Thyroid dose received apparently shielded
by cerrobend blocks was about 8cGy in 100cGy Expose
Abstract: To fight against the economic crisis, French
Government, like many others in Europe, has decided to give a boost
to high-speed line projects. This paper explores the implementation
and decision-making process in TGV projects, their evolutions,
especially since the Mediterranean TGV-line. This project was
probably the most controversial, but paradoxically represents today a
huge success for all the actors involved.
What kind of lessons we can learn from this experience? How to
evaluate the impact of this project on TGV-line planning? How can
we characterize this implementation and decision-making process
regards to the sustainability challenges?
The construction of Mediterranean TGV-line was the occasion to
make several innovations: to introduce more dialog into the decisionmaking
process, to take into account the environment, to introduce a
new project management and technological innovations. That-s why
this project appears today as an example in terms of integration of
sustainable development.
In this paper we examine the different kinds of innovations
developed in this project, by using concepts from sociology of
innovation to understand how these solutions emerged in a
controversial situation. Then we analyze the lessons which were
drawn from this decision-making process (in the immediacy and a
posteriori) and the way in which procedures evolved: creation of new
tools and devices (public consultation, project management...).
Finally we try to highlight the impact of this evolution on TGV
projects governance. In particular, new methods of implementation
and financing involve a reconfiguration of the system of actors. The
aim of this paper is to define the impact of this reconfiguration on
negotiations between stakeholders.
Abstract: The results of the two-phase gas-solid jet in pneumatic
powder injection process analysis were presented in the paper. The
researches were conducted on model set-up with high speed camera
jet movement recording. Then the recorded material was analyzed to
estimate main particles movement parameters. The values obtained
from this direct measurement were compared to those calculated with
the use of the well-known formulas for the two-phase flows
(pneumatic conveying). Moreover, they were compared to
experimental results previously achieved by authors. The analysis led
to conclusions which to some extent changed the assumptions used
even by authors, regarding the two-phase jet in pneumatic powder
injection process. Additionally, the visual analysis of the recorded
clips supplied data to make a more complete evaluation of the jet
behavior in the lance outlet than before.
Abstract: Deaminated lesions were produced via nitrosative oxidation of natural nucleobases; uracul (Ura, U) from cytosine (Cyt, C), hypoxanthine (Hyp, H) from adenine (Ade, A), and xanthine (Xan, X) and oxanine (Oxa, O) from guanine (Gua, G). Such damaged nucleobases may induce mutagenic problems, so that much attentions and efforts have been poured on the revealing of their mechanisms in vivo or in vitro. In this study, we employed these deaminated lesions as useful probes for analysis of DNA-binding/recognizing proteins or enzymes. Since the pyrimidine lesions such as Hyp, Oxa and Xan are employed as analogues of guanine, their comparative uses are informative for analyzing the role of Gua in DNA sequence in DNA-protein interaction. Several DNA oligomers containing such Hyp, Oxa or Xan substituted for Gua were designed to reveal the molecular interaction between DNA and protein. From this approach, we have got useful information to understand the molecular mechanisms of the DNA-recognizing enzymes, which have not ever been observed using conventional DNA oligomer composed of just natural nucleobases.
Abstract: We study the spatial design of experiment and we want to select a most informative subset, having prespecified size, from a set of correlated random variables. The problem arises in many applied domains, such as meteorology, environmental statistics, and statistical geology. In these applications, observations can be collected at different locations and possibly at different times. In spatial design, when the design region and the set of interest are discrete then the covariance matrix completely describe any objective function and our goal is to choose a feasible design that minimizes the resulting uncertainty. The problem is recast as that of maximizing the determinant of the covariance matrix of the chosen subset. This problem is NP-hard. For using these designs in computer experiments, in many cases, the design space is very large and it's not possible to calculate the exact optimal solution. Heuristic optimization methods can discover efficient experiment designs in situations where traditional designs cannot be applied, exchange methods are ineffective and exact solution not possible. We developed a GA algorithm to take advantage of the exploratory power of this algorithm. The successful application of this method is demonstrated in large design space. We consider a real case of design of experiment. In our problem, design space is very large and for solving the problem, we used proposed GA algorithm.
Abstract: The paper presents the brief information on particular results of experimental study focused to the problems of behavior of structural plated components made of fiber-cement-based materials and used in building constructions, exposed to atmospheric physical effects given by the weather changes in the summer period. Weather changes represented namely by temperature and rain cause also the changes of the temperature and moisture of the investigated structural components. This can affect their static behavior that means stresses and deformations, which have been monitored as the main outputs of tests performed. Experimental verification is based on the simulation of the influence of temperature and rain using the defined procedure of warming and water sprinkling with respect to the corresponding weather conditions during summer period in the South Moravian region at the Czech Republic, for which the application of these structural components is mainly planned. Two types of components have been tested: (i) glass-fiber-concrete panels used for building façades and (ii) fiber-cement slabs used mainly for claddings, but also as a part of floor structures or lost shuttering, and so on.
Abstract: Public awareness towards green energy are on the rise and this can be prove by many product being manufactured or prerequired to be made as energy saving devices mainly to save consumer from spending more on utility billing. These schemes are popular nowadays and many homemade appliances are turned into energy saving gadget which attracts the attention of consumers. Knowing the public demands and pattern towards purchasing home appliances thus the idea of “energy saving suction hood (ESSH)" is proposed. The ESSH can be used in many places that require smoke ventilation or even to reduce the room temperature as many conventional suction hoods (CSH) do, but this device works automatically by the usage of sensors that detects the smoke/temperature and automatically spins the exhaust fan. As it turns, the mechanical rotation rotates the AC generator which is coupled together with the fan and then charges the battery. The innovation of this product is, it does not rely on the utility supply as it is also hook up with a solar panel which also charges the battery, Secondly, it generates energy as the exhaust fan mechanically rotates. Thirdly, an energy loop back feature is introduced to this system which will supply for the ventilator fan. Another major innovation is towards interfacing this device with an in house production of generator. This generator is produced by proper design on stator as well as rotor to reduce the losses. A comparison is made between the ESSH and the CSH and result shows that the ESSH saves 172.8kWh/year of utility supply which is used by CSH. This amount of energy can save RM 3.14 from monthly utility bill and a total of RM 37.67 per year. In fact this product can generate 175 Watt of power from generator(75W) and solar panel(100W) that can be used either to supply other household appliances and/or to loop back to supply the fans motor. The innovation of this system is essential for future production of other equipment by using the loopback power method and turning most equipment into a standalone system.
Abstract: The purpose of this study is to identify the critical success factors (CSFs) for the effective implementation of Six Sigma in non-formal service Sectors.
Based on the survey of literature, the critical success factors (CSFs) for Six Sigma have been identified and are assessed for their importance in Non-formal service sector using Delphi Technique. These selected CSFs were put forth to the panel of expert to cluster them and prepare cognitive map to establish their relationship.
All the critical success factors examined and obtained from the review of literature have been assessed for their importance with respect to their contribution to Six Sigma effectiveness in non formal service sector.
The study is limited to the non-formal service sectors involved in the organization of religious festival only. However, the similar exercise can be conducted for broader sample of other non-formal service sectors like temple/ashram management, religious tours management etc.
The research suggests an approach to identify CSFs of Six Sigma for Non-formal service sector. All the CSFs of the formal service sector will not be applicable to Non-formal services, hence opinion of experts was sought to add or delete the CSFs. In the first round of Delphi, the panel of experts has suggested, two new CSFs-“competitive benchmarking (F19) and resident’s involvement (F28)”, which were added for assessment in the next round of Delphi. One of the CSFs-“fulltime six sigma personnel (F15)” has been omitted in proposed clusters of CSFs for non-formal organization, as it is practically impossible to deploy full time trained Six Sigma recruits.
Abstract: Static synchronous compensator (STATCOM) is a shunt connected voltage source converter (VSC), which can affect rapid control of reactive flow in the transmission line by controlling the generated a.c. voltage. The main aim of the paper is to design a power system installed with a Static synchronous compensator (STATCOM) and demonstrates the application of the linearised Phillips-heffron model in analyzing the damping effect of the STATCOM to improve power system oscillation stability. The proposed PI controller is designed to coordinate two control inputs: Voltage of the injection bus and capacitor voltage of the STATCOM, to improve the Dynamic stability of a SMIB system .The power oscillations damping (POD) control and power system stabilizer (PSS) and their coordinated action with proposed controllers are tested. The simulation result shows that the proposed damping controllers provide satisfactory performance in terms of improvements of dynamic stability of the system.
Abstract: Cryptographic algorithms play a crucial role in the
information society by providing protection from unauthorized
access to sensitive data. It is clear that information technology will
become increasingly pervasive, Hence we can expect the emergence
of ubiquitous or pervasive computing, ambient intelligence. These
new environments and applications will present new security
challenges, and there is no doubt that cryptographic algorithms and
protocols will form a part of the solution. The efficiency of a public
key cryptosystem is mainly measured in computational overheads,
key size and bandwidth. In particular the RSA algorithm is used in
many applications for providing the security. Although the security
of RSA is beyond doubt, the evolution in computing power has
caused a growth in the necessary key length. The fact that most chips
on smart cards can-t process key extending 1024 bit shows that there
is need for alternative. NTRU is such an alternative and it is a
collection of mathematical algorithm based on manipulating lists of
very small integers and polynomials. This allows NTRU to high
speeds with the use of minimal computing power. NTRU (Nth degree
Truncated Polynomial Ring Unit) is the first secure public key
cryptosystem not based on factorization or discrete logarithm
problem. This means that given sufficient computational resources
and time, an adversary, should not be able to break the key. The
multi-party communication and requirement of optimal resource
utilization necessitated the need for the present day demand of
applications that need security enforcement technique .and can be
enhanced with high-end computing. This has promoted us to develop
high-performance NTRU schemes using approaches such as the use
of high-end computing hardware. Peer-to-peer (P2P) or enterprise
grids are proven as one of the approaches for developing high-end
computing systems. By utilizing them one can improve the
performance of NTRU through parallel execution. In this paper we
propose and develop an application for NTRU using enterprise grid
middleware called Alchemi. An analysis and comparison of its
performance for various text files is presented.
Abstract: This work focuses on analysis of classical heat transfer equation regularized with Maxwell-Cattaneo transfer law. Computer simulations are performed in MATLAB environment. Numerical experiments are first developed on classical Fourier equation, then Maxwell-Cattaneo law is considered. Corresponding equation is regularized with a balancing diffusion term to stabilize discretizing scheme with adjusted time and space numerical steps. Several cases including a convective term in model equations are discussed, and results are given. It is shown that limiting conditions on regularizing parameters have to be satisfied in convective case for Maxwell-Cattaneo regularization to give physically acceptable solutions. In all valid cases, uniform convergence to solution of initial heat equation with Fourier law is observed, even in nonlinear case.