Abstract: This paper proposes a hybrid method for eyes localization
in facial images. The novelty is in combining techniques
that utilise colour, edge and illumination cues to improve accuracy.
The method is based on the observation that eye regions have dark
colour, high density of edges and low illumination as compared
to other parts of face. The first step in the method is to extract
connected regions from facial images using colour, edge density and
illumination cues separately. Some of the regions are then removed
by applying rules that are based on the general geometry and shape
of eyes. The remaining connected regions obtained through these
three cues are then combined in a systematic way to enhance the
identification of the candidate regions for the eyes. The geometry
and shape based rules are then applied again to further remove the
false eye regions. The proposed method was tested using images from
the PICS facial images database. The proposed method has 93.7%
and 87% accuracies for initial blobs extraction and final eye detection
respectively.
Abstract: This research aims to study the lead pollution in the air of Babylon governorate that resulted generally from vehicles exhausts in addition to industrial and human activities.Vehicles number in Babylon governorate increased significantly after year 2003 that resulted with increase in lead emissions into the air.Measurement of lead emissions was done in seven stations distributed randomly in Babylon governorate. These stations where located in Industrial (Al-Sena'ay) Quarter, 60 street (near to Babylon sewer directorate), 40 Street (near to the first intersection), Al-Hashmia city, Al-Mahaweel city, , Al- Musayab city in addition to another station in Sayd Idris village belong to Abugharaq district (Agricultural station for comparison). The measured concentrations in these stations were compared with the standard limits of Environmental Protection Agency EPA (2 μg /m3). The results of this study showed that the average of lead concentrations ,in Babylon governorate during year 2010, was (3.13 μg/m3) which was greater than standard limits (2 μg/m3). The maximum concentration of lead was (6.41 μg / m3) recorded in the Industrial (Al-Sena'ay) Quarter during April month, while the minimum concentrations was (0.36 μg / m3) recorded in the agricultural station (Abugharaq) during December month.
Abstract: The paper investigates the potential of support vector
machines and Gaussian process based regression approaches to
model the oxygen–transfer capacity from experimental data of
multiple plunging jets oxygenation systems. The results suggest the
utility of both the modeling techniques in the prediction of the
overall volumetric oxygen transfer coefficient (KLa) from operational
parameters of multiple plunging jets oxygenation system. The
correlation coefficient root mean square error and coefficient of
determination values of 0.971, 0.002 and 0.945 respectively were
achieved by support vector machine in comparison to values of
0.960, 0.002 and 0.920 respectively achieved by Gaussian process
regression. Further, the performances of both these regression
approaches in predicting the overall volumetric oxygen transfer
coefficient was compared with the empirical relationship for multiple
plunging jets. A comparison of results suggests that support vector
machines approach works well in comparison to both empirical
relationship and Gaussian process approaches, and could successfully
be employed in modeling oxygen-transfer.
Abstract: The paper gives the pilot results of the project that is
oriented on the use of data mining techniques and knowledge
discoveries from production systems through them. They have been
used in the management of these systems. The simulation models of
manufacturing systems have been developed to obtain the necessary
data about production. The authors have developed the way of
storing data obtained from the simulation models in the data
warehouse. Data mining model has been created by using specific
methods and selected techniques for defined problems of production
system management. The new knowledge has been applied to
production management system. Gained knowledge has been tested
on simulation models of the production system. An important benefit
of the project has been proposal of the new methodology. This
methodology is focused on data mining from the databases that store
operational data about the production process.
Abstract: A mammography image is composed of low contrast area where the breast tissues and the breast abnormalities such as microcalcification can hardly be differentiated by the medical practitioner. This paper presents the application of active contour models (Snakes) for the segmentation of microcalcification in mammography images. Comparison on the microcalcifiation areas segmented by the Balloon Snake, Gradient Vector Flow (GVF) Snake, and Distance Snake is done against the true value of the microcalcification area. The true area value is the average microcalcification area in the original mammography image traced by the expert radiologists. From fifty images tested, the result obtained shows that the accuracy of the Balloon Snake, GVF Snake, and Distance Snake in segmenting boundaries of microcalcification are 96.01%, 95.74%, and 95.70% accuracy respectively. This implies that the Balloon Snake is a better segmentation method to locate the exact boundary of a microcalcification region.
Abstract: Carbon disulfide is widely used for the production of
viscose rayon, rubber, and other organic materials and it is a
feedstock for the synthesis of sulfuric acid. The objective of this
paper is to analyze possibilities for efficient production of CS2 from
sour natural gas reformation (H2SMR) (2H2S+CH4 =CS2 +4H2) .
Also, the effect of H2S to CH4 feed ratio and reaction temperature on
carbon disulfide production is investigated numerically in a
reforming reactor. The chemical reaction model is based on an
assumed Probability Density Function (PDF) parameterized by the
mean and variance of mixture fraction and β-PDF shape. The results
show that the major factors influencing CS2 production are reactor
temperature. The yield of carbon disulfide increases with increasing
H2S to CH4 feed gas ratio (H2S/CH4≤4). Also the yield of C(s)
increases with increasing temperature until the temperature reaches
to 1000°K, and then due to increase of CS2 production and
consumption of C(s), yield of C(s) drops with further increase in the
temperature. The predicted CH4 and H2S conversion and yield of
carbon disulfide are in good agreement with result of Huang and TRaissi.
Abstract: Recent advances in wireless sensor networks have led
to many routing methods designed for energy-efficiency in wireless
sensor networks. Despite that many routing methods have been
proposed in USN, a single routing method cannot be energy-efficient
if the environment of the ubiquitous sensor network varies. We present
the controlling network access to various hosts and the services they
offer, rather than on securing them one by one with a network security
model. When ubiquitous sensor networks are deployed in hostile
environments, an adversary may compromise some sensor nodes and
use them to inject false sensing reports. False reports can lead to not
only false alarms but also the depletion of limited energy resource in
battery powered networks. The interleaved hop-by-hop authentication
scheme detects such false reports through interleaved authentication.
This paper presents a LMDD (Low energy method for data delivery)
algorithm that provides energy-efficiency by dynamically changing
protocols installed at the sensor nodes. The algorithm changes
protocols based on the output of the fuzzy logic which is the fitness
level of the protocols for the environment.
Abstract: Matrix metalloproteinase-3 (MMP3) is key member
of the MMP family, and is known to be present in coronary
atherosclerotic. Several studies have demonstrated that MMP-3
5A/6A polymorphism modify each transcriptional activity in allele
specific manner. We hypothesized that this polymorphism may play
a role as risk factor for development of coronary stenosis. The aim of
our study was to estimate MMP-3 (5A/6A) gene polymorphism on
interindividual variability in risk for coronary stenosis in an Iranian
population.DNA was extracted from white blood cells and genotypes
were obtained from coronary stenosis cases (n=95) and controls
(n=100) by PCR (polymerase chain reaction) and restriction
fragment length polymorphism techniques. Significant differences
between cases and controls were observed for MMP3 genotype
frequencies (X2=199.305, p< 0.001); the 6A allele was less
frequently seen in the control group, compared to the disease group
(85.79 vs. 78%, 6A/6A+5A/6A vs. 5A/5A, P≤0.001). These data
imply the involvement of -1612 5A/6A polymorphism in coronary
stenosis, and suggest that probably the 6A/6A MMP-3 genotype is a
genetic susceptibility factor for coronary stenosis.
Abstract: The objective of the present study was to determine
the effect of different concentration of spermatozoa and length of
storage in 5 0C on sperm motility. Semen was collected using
artificial vagina from goat aged 2 to 2.5 years. Fresh goat semen
with sperm motility ≥ 70% was used as material. Semen was
divided into 4 treatments of concentration (40 x 10 6 / ml, 50 x
106/ml, 60x106/ml, 70x106/ml) with length of storage 0,12,24,36 h. in
5 0C. There were interactions (P
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: This paper describes the design of a programmable
FSK-modulator based on VCO and its implementation in 0.35m
CMOS process. The circuit is used to transmit digital data at
100Kbps rate in the frequency range of 400-600MHz. The design
and operation of the modulator is discussed briefly. Further the
characteristics of PLL, frequency synthesizer, VCO and the whole
design are elaborated. The variation among the proposed and tested
specifications is presented. Finally, the layout of sub-modules, pin
configurations, final chip and test results are presented.
Abstract: The utilize of renewable energy sources becomes
more crucial and fascinatingly, wider application of renewable
energy devices at domestic, commercial and industrial levels is not
only affect to stronger awareness but also significantly installed
capacities. Moreover, biomass principally is in form of woods and
converts to be energy for using by humans for a long time.
Gasification is a process of conversion of solid carbonaceous fuel
into combustible gas by partial combustion. Many gasified models
have various operating conditions because the parameters kept in
each model are differentiated. This study applied the experimental
data including three inputs variables including biomass consumption;
temperature at combustion zone and ash discharge rate and gas flow
rate as only one output variable. In this paper, response surface
methods were applied for identification of the gasified system
equation suitable for experimental data. The result showed that linear
model gave superlative results.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: Prickly pear juice has received renewed attention with regard to the effects of processing and preservation on its sensory qualities (colour, taste, flavour, aroma, astringency, visual browning and overall acceptability). Juice was prepared by homogenizing fruit and treating the pulp with pectinase (Aspergillus niger). Juice treatments applied were sugar addition, acidification, heat-treatment, refrigeration, and freezing and thawing. Prickly pear pulp and juice had unique properties (low pH 3.88, soluble solids 3.68 oBrix and high titratable acidity 0.47). Sensory profiling and descriptive analyses revealed that non-treated juice had a bitter taste with high astringency whereas treated prickly pear was significantly sweeter. All treated juices had a good sensory acceptance with values approximating or exceeding 7. Regression analysis of the consumer sensory attributes for non-treated prickly pear juice indicated an overwhelming rejection, while treated prickly pear juice received overall acceptability. Thus, educed favourable sensory responses and may have positive implications for consumer acceptability.
Abstract: Fischer-Tropsch synthesis is one of the most
important catalytic reactions that convert the synthetic gas to light
and heavy hydrocarbons. One of the main issues is selecting the type
of reactor. The slurry bubble reactor is suitable choice for Fischer-
Tropsch synthesis because of its good qualification to transfer heat
and mass, high durability of catalyst, low cost maintenance and
repair. The more common catalysts for Fischer-Tropsch synthesis are
Iron-based and Cobalt-based catalysts, the advantage of these
catalysts on each other depends on which type of hydrocarbons we
desire to produce. In this study, Fischer-Tropsch synthesis is modeled
with Iron and Cobalt catalysts in a slurry bubble reactor considering
mass and momentum balance and the hydrodynamic relations effect
on the reactor behavior. Profiles of reactant conversion and reactant
concentration in gas and liquid phases were determined as the
functions of residence time in the reactor. The effects of temperature,
pressure, liquid velocity, reactor diameter, catalyst diameter, gasliquid
and liquid-solid mass transfer coefficients and kinetic
coefficients on the reactant conversion have been studied. With 5%
increase of liquid velocity (with Iron catalyst), H2 conversions
increase about 6% and CO conversion increase about 4%, With 8%
increase of liquid velocity (with Cobalt catalyst), H2 conversions
increase about 26% and CO conversion increase about 4%. With
20% increase of gas-liquid mass transfer coefficient (with Iron
catalyst), H2 conversions increase about 12% and CO conversion
increase about 10% and with Cobalt catalyst H2 conversions increase
about 10% and CO conversion increase about 6%. Results show that
the process is sensitive to gas-liquid mass transfer coefficient and
optimum condition operation occurs in maximum possible liquid
velocity. This velocity must be more than minimum fluidization
velocity and less than terminal velocity in such a way that avoid
catalysts particles from leaving the fluidized bed.
Abstract: Sparse representation which can represent high dimensional
data effectively has been successfully used in computer vision
and pattern recognition problems. However, it doesn-t consider the
label information of data samples. To overcome this limitation,
we develop a novel dimensionality reduction algorithm namely
dscriminatively regularized sparse subspace learning(DR-SSL) in this
paper. The proposed DR-SSL algorithm can not only make use of
the sparse representation to model the data, but also can effective
employ the label information to guide the procedure of dimensionality
reduction. In addition,the presented algorithm can effectively deal
with the out-of-sample problem.The experiments on gene-expression
data sets show that the proposed algorithm is an effective tool for
dimensionality reduction and gene-expression data classification.
Abstract: Intellectual capital measurement is a central aspect of knowledge management. The measurement and the evaluation of intangible assets play a key role in allowing an effective management of these assets as sources of competitiveness. For these reasons, managers and practitioners need conceptual and analytical tools taking into account the unique characteristics and economic significance of Intellectual Capital. Following this lead, we propose an efficiency and productivity analysis of Intellectual Capital, as a determinant factor of the company competitive advantage. The analysis is carried out by means of Data Envelopment Analysis (DEA) and Malmquist Productivity Index (MPI). These techniques identify Bests Practice companies that have accomplished competitive advantage implementing successful strategies of Intellectual Capital management, and offer to inefficient companies development paths by means of benchmarking. The proposed methodology is employed on the Biotechnology industry in the period 2007-2010.
Abstract: Nowadays there are several grid connected converter
in the grid system. These grid connected converters are generally the
converters of renewable energy sources, industrial four quadrant
drives and other converters with DC link. These converters are
connected to the grid through a three phase bridge. The standards
prescribe the maximal harmonic emission which could be easily
limited with high switching frequency. The increased switching
losses can be reduced to the half with the utilization of the wellknown
Flat-top modulation. The suggested control method is the
expansion of the Flat-top modulation with which the losses could be
also reduced to the half compared to the Flat-top modulation.
Comparing to traditional control these requirements can be
simultaneously satisfied much better with the DLF (DC Link
Floating) method.
Abstract: This paper is concerned with a nonautonomous three species food chain model with Crowley–Martin type functional response and time delay. Using the Mawhin-s continuation theorem in theory of degree, sufficient conditions for existence of periodic solutions are obtained.
Abstract: The success of an e-learning system is highly
dependent on the quality of its educational content and how effective,
complete, and simple the design tool can be for teachers. Educational
modeling languages (EMLs) are proposed as design languages
intended to teachers for modeling diverse teaching-learning
experiences, independently of the pedagogical approach and in
different contexts. However, most existing EMLs are criticized for
being too abstract and too complex to be understood and manipulated
by teachers. In this paper, we present a visual EML that simplifies the
process of designing learning scenarios for teachers with no
programming background. Based on the conceptual framework of the
activity theory, our resulting visual EML focuses on using Domainspecific
modeling techniques to provide a pedagogical level of
abstraction in the design process.