Abstract: A structural study of an aqueous electrolyte whose
experimental results are available. It is a solution of LiCl-6H2O type
at glassy state (120K) contrasted with pure water at room temperature
by means of Partial Distribution Functions (PDF) issue from neutron
scattering technique. Based on these partial functions, the Reverse
Monte Carlo method (RMC) computes radial and angular correlation
functions which allow exploring a number of structural features of
the system. The obtained curves include some artifacts. To remedy
this, we propose to introduce a screened potential as an additional
constraint. Obtained results show a good matching between
experimental and computed functions and a significant improvement
in PDFs curves with potential constraint. It suggests an efficient fit of
pair distribution functions curves.
Abstract: Background: Widespread use of chemotherapeutic
drugs in the treatment of cancer has lead to higher health hazards
among employee who handle and administer such drugs, so nurses
should know how to protect themselves, their patients and their work
environment against toxic effects of chemotherapy. Aim of this study
was carried out to examine the effect of chemotherapy safety protocol
for oncology nurses on their protective measure practices. Design: A
quasi experimental research design was utilized. Setting: The study
was carried out in oncology department of Menoufia university
hospital and Tanta oncology treatment center. Sample: A
convenience sample of forty five nurses in Tanta oncology treatment
center and eighteen nurses in Menoufiya oncology department.
Tools: 1. an interviewing questionnaire that covering sociodemographic
data, assessment of unit and nurses' knowledge about
chemotherapy. II: Obeservational check list to assess nurses' actual
practices of handling and adminestration of chemotherapy. A base
line data were assessed before implementing Chemotherapy Safety
protocol, then Chemotherapy Safety protocol was implemented, and
after 2 monthes they were assessed again. Results: reveled that 88.9%
of study group I and 55.6% of study group II improved to good total
knowledge scores after educating on the safety protocol, also 95.6%
of study group I and 88.9% of study group II had good total practice
score after educating on the safety protocol. Moreover less than half
of group I (44.4%) reported that heavy workload is the most barriers
for them, while the majority of group II (94.4%) had many barriers
for adhering to the safety protocol such as they didn’t know the
protocol, the heavy work load and inadequate equipment.
Conclusions: Safety protocol for Oncology Nurses seemed to have
positive effect on improving nurses' knowledge and practice.
Recommendation: chemotherapy safety protocol should be instituted
for all oncology nurses who are working in any oncology unit and/ or
center to enhance compliance, and this protocol should be done at
frequent intervals.
Abstract: Clean air in subway station is important to passengers. The Platform Screen Doors (PSDs) can improve indoor air quality in the subway station; however the air quality in the subway tunnel is degraded. The subway tunnel has high CO2 concentration and indoor particulate matter (PM) value. The Indoor Air Quality (IAQ) level in subway environment degrades by increasing the frequency of the train operation and the number of the train. The ventilation systems of the subway tunnel need improvements to have better air-quality. Numerical analyses might be effective tools to analyze the performance of subway twin-track tunnel ventilation systems. An existing subway twin-track tunnel in the metropolitan Seoul subway system is chosen for the numerical simulations. The ANSYS CFX software is used for unsteady computations of the airflow inside the twin-track tunnel when the train moves. The airflow inside the tunnel is simulated when one train runs and two trains run at the same time in the tunnel. The piston-effect inside the tunnel is analyzed when all shafts function as the natural ventilation shaft. The supplied air through the shafts is mixed with the pollutant air in the tunnel. The pollutant air is exhausted by the mechanical ventilation shafts. The supplied and discharged airs are balanced when only one train runs in the twin-track tunnel. The pollutant air in the tunnel is high when two trains run simultaneously in opposite direction and all shafts functioned as the natural shaft cases when there are no electrical power supplies in the shafts. The remained pollutant air inside the tunnel enters into the station platform when the doors are opened.
Abstract: Airport capacity has always been perceived in the
traditional sense as the number of aircraft operations during a
specified time corresponding to a tolerable level of average delay and
it mostly depends on the airside characteristics, on the fleet mix
variability and on the ATM. The adoption of the Directive
2002/30/EC in the EU countries drives the stakeholders to conceive
airport capacity in a different way though. Airport capacity in this
sense is fundamentally driven by environmental criteria, and since
acoustical externalities represent the most important factors, those are
the ones that could pose a serious threat to the growth of airports and
to aviation market itself in the short-medium term. The importance of
the regional airports in the deregulated market grew fast during the
last decade since they represent spokes for network carriers and a
preferential destination for low-fares carriers. Not only regional
airports have witnessed a fast and unexpected growth in traffic but
also a fast growth in the complaints for the nuisance by the people
living near those airports. In this paper the results of a study
conducted in cooperation with the airport of Bologna G. Marconi are
presented in order to investigate airport acoustical capacity as a defacto
constraint of airport growth.
Abstract: Overcurrent (OC) relays are the major protection
devices in a distribution system. The operating time of the OC relays
are to be coordinated properly to avoid the mal-operation of the
backup relays. The OC relay time coordination in ring fed
distribution networks is a highly constrained optimization problem
which can be stated as a linear programming problem (LPP). The
purpose is to find an optimum relay setting to minimize the time of
operation of relays and at the same time, to keep the relays properly
coordinated to avoid the mal-operation of relays.
This paper presents two phase simplex method for optimum time
coordination of OC relays. The method is based on the simplex
algorithm which is used to find optimum solution of LPP. The
method introduces artificial variables to get an initial basic feasible
solution (IBFS). Artificial variables are removed using iterative
process of first phase which minimizes the auxiliary objective
function. The second phase minimizes the original objective function
and gives the optimum time coordination of OC relays.
Abstract: Support Vector Machine (SVM) is a statistical learning tool that was initially developed by Vapnik in 1979 and later developed to a more complex concept of structural risk minimization (SRM). SVM is playing an increasing role in applications to detection problems in various engineering problems, notably in statistical signal processing, pattern recognition, image analysis, and communication systems. In this paper, SVM was applied to the detection of medical ultrasound images in the presence of partially developed speckle noise. The simulation was done for single look and multi-look speckle models to give a complete overlook and insight to the new proposed model of the SVM-based detector. The structure of the SVM was derived and applied to clinical ultrasound images and its performance in terms of the mean square error (MSE) metric was calculated. We showed that the SVM-detected ultrasound images have a very low MSE and are of good quality. The quality of the processed speckled images improved for the multi-look model. Furthermore, the contrast of the SVM detected images was higher than that of the original non-noisy images, indicating that the SVM approach increased the distance between the pixel reflectivity levels (detection hypotheses) in the original images.
Abstract: Antimicrobial resistant is becoming a major factor in
virtually all hospital acquired infection may soon untreatable is a
serious public health problem. These concerns have led to major
research effort to discover alternative strategies for the treatment of
bacterial infection. Nanobiotehnology is an upcoming and fast
developing field with potential application for human welfare. An
important area of nanotechnology for development of reliable and
environmental friendly process for synthesis of nanoscale particles
through biological systems In the present studies are reported on the
use of fungal strain Aspergillus species for the extracellular synthesis
of bionanoparticles from 1 mM silver nitrate (AgNO3) solution. The
report would be focused on the synthesis of metallic bionanoparticles
of silver using a reduction of aqueous Ag+ ion with the
culture supernatants of Microorganisms. The bio-reduction of the
Ag+ ions in the solution would be monitored in the aqueous
component and the spectrum of the solution would measure through
UV-visible spectrophotometer The bionanoscale particles were
further characterized by Atomic Force Microscopy (AFM), Fourier
Transform Infrared Spectroscopy (FTIR) and Thin layer
chromatography. The synthesized bionanoscale particle showed a
maximum absorption at 385 nm in the visible region. Atomic Force
Microscopy investigation of silver bionanoparticles identified that
they ranged in the size of 250 nm - 680 nm; the work analyzed the
antimicrobial efficacy of the silver bionanoparticles against various
multi drug resistant clinical isolates. The present Study would be
emphasizing on the applicability to synthesize the metallic
nanostructures and to understand the biochemical and molecular
mechanism of nanoparticles formation by the cell filtrate in order to
achieve better control over size and polydispersity of the
nanoparticles. This would help to develop nanomedicine against
various multi drug resistant human pathogens.
Abstract: Localized surface plasmon resonance (LSPR) is the
coherent oscillation of conductive electrons confined in noble
metallic nanoparticles excited by electromagnetic radiation, and
nanosphere lithography (NSL) is one of the cost-effective methods to
fabricate metal nanostructures for LSPR. NSL can be categorized
into two major groups: dispersed NSL and closely pack NSL. In
recent years, gold nanocrescents and gold nanoholes with vertical
sidewalls fabricated by dispersed NSL, and silver nanotriangles and
gold nanocaps on silica nanospheres fabricated by closely pack NSL,
have been reported for LSPR biosensing. This paper introduces
several novel gold nanostructures fabricated by NSL in LSPR
applications, including 3D nanostructures obtained by evaporating
gold obliquely on dispersed nanospheres, nanoholes with slant
sidewalls, and patchy nanoparticles on closely packed nanospheres,
all of which render satisfactory sensitivity for LSPR sensing. Since
the LSPR spectrum is very sensitive to the shape of the metal
nanostructures, formulas are derived and software is developed for
calculating the profiles of the obtainable metal nanostructures by
NSL, for different nanosphere masks with different fabrication
conditions. The simulated profiles coincide well with the profiles of
the fabricated gold nanostructures observed under scanning electron
microscope (SEM) and atomic force microscope (AFM), which
proves that the software is a useful tool for the process design of
different LSPR nanostructures.
Abstract: Importance of software quality is increasing leading to development of new sophisticated techniques, which can be used in constructing models for predicting quality attributes. One such technique is Artificial Neural Network (ANN). This paper examined the application of ANN for software quality prediction using Object- Oriented (OO) metrics. Quality estimation includes estimating maintainability of software. The dependent variable in our study was maintenance effort. The independent variables were principal components of eight OO metrics. The results showed that the Mean Absolute Relative Error (MARE) was 0.265 of ANN model. Thus we found that ANN method was useful in constructing software quality model.
Abstract: The purpose of this paper isunavailability of the two main types of conveSwedish traction power supply (TPS) system, i.e.static converter. The number of outages and the ouused to analyze and compare the unavailability oconverters. The mean cumulative function (MCF)analyze the number of outages and the unavailabthe forced outage rate (FOR) concept has been uoutage rates. The study shows that the outagesfailure occur at a constant rate by calendar timconverter stations, while very few stations havedecreasing rate. It has also been found that the stata higher number of outages and a higher outage ratcompared to the rotary converter types. The resultsthat combining the number of outages and the fgives a better view of the converters performasupport for the maintenance decision. In fact, usingdoes not reflect reality. Comparing these two indein identifying the areas where extra resources are maintenance planning and where improvementsoutage in the TPS system.KeywordsFrequency Converter, Forced OuCumulative Function, Traction Power Supply, ESystems.
Abstract: We present a new method for the fully automatic 3D
reconstruction of the coronary artery centerlines, using two X-ray
angiogram projection images from a single rotating monoplane
acquisition system. During the first stage, the input images are
smoothed using curve evolution techniques. Next, a simple yet
efficient multiscale method, based on the information of the Hessian
matrix, for the enhancement of the vascular structure is introduced.
Hysteresis thresholding using different image quantiles, is used to
threshold the arteries. This stage is followed by a thinning procedure
to extract the centerlines. The resulting skeleton image is then pruned
using morphological and pattern recognition techniques to remove
non-vessel like structures. Finally, edge-based stereo correspondence
is solved using a parallel evolutionary optimization method based on
f symbiosis. The detected 2D centerlines combined with disparity
map information allow the reconstruction of the 3D vessel
centerlines. The proposed method has been evaluated on patient data
sets for evaluation purposes.
Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: The principle of frequency and amplitude measurement of a vibrating object in water using ultrasonic speckle technique is presented in this paper. Compared with other traditional techniques, the ultrasonic speckle technique can be applied to vibration measurement of a nonmetal object with rough surface in water in a noncontact way. The relationship between speckle movement and object movement was analyzed. Based on this study, an ultrasonic speckle measurement system was set up. With this system the frequency and amplitude of an underwater vibrating cantilever beam was detected. The result shows that the experimental data is in good agreement with the calibrating data.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: The problem of estimating time-varying regression is
inevitably concerned with the necessity to choose the appropriate
level of model volatility - ranging from the full stationarity of instant
regression models to their absolute independence of each other. In the
stationary case the number of regression coefficients to be estimated
equals that of regressors, whereas the absence of any smoothness
assumptions augments the dimension of the unknown vector by the
factor of the time-series length. The Akaike Information Criterion
is a commonly adopted means of adjusting a model to the given
data set within a succession of nested parametric model classes,
but its crucial restriction is that the classes are rigidly defined by
the growing integer-valued dimension of the unknown vector. To
make the Kullback information maximization principle underlying the
classical AIC applicable to the problem of time-varying regression
estimation, we extend it onto a wider class of data models in which
the dimension of the parameter is fixed, but the freedom of its values
is softly constrained by a family of continuously nested a priori
probability distributions.
Abstract: To evaluate genetic variation of wheat (Triticum
aestivum) affected by heat and drought stress on eight Australian
wheat genotypes that are parents of Doubled Haploid (HD) mapping
populations at the vegetative stage, the water stress experiment was
conducted at 65% field capacity in growth room. Heat stress
experiment was conducted in the research field under irrigation over
summer. Result show that water stress decreased dry shoot weight
and RWC but increased osmolarity and means of Fv/Fm values in all
varieties except for Krichauff. Krichauff and Kukri had the
maximum RWC under drought stress. Trident variety was shown
maximum WUE, osmolarity (610 mM/Kg), dry mater, quantum yield
and Fv/Fm 0.815 under water stress condition. However, the
recovery of quantum yield was apparent between 4 to 7 days after
stress in all varieties. Nevertheless, increase in water stress after that
lead to strong decrease in quantum yield. There was a genetic
variation for leaf pigments content among varieties under heat stress.
Heat stress decreased significantly the total chlorophyll content that
measured by SPAD. Krichauff had maximum value of Anthocyanin
content (2.978 A/g FW), chlorophyll a+b (2.001 mg/g FW) and
chlorophyll a (1.502 mg/g FW). Maximum value of chlorophyll b
(0.515 mg/g FW) and Carotenoids (0.234 mg/g FW) content
belonged to Kukri. The quantum yield of all varieties decreased
significantly, when the weather temperature increased from 28 ÔùªC to
36 ÔùªC during the 6 days. However, the recovery of quantum yield
was apparent after 8th day in all varieties. The maximum decrease
and recovery in quantum yield was observed in Krichauff. Drought
and heat tolerant and moderately tolerant wheat genotypes were
included Trident, Krichauff, Kukri and RAC875. Molineux, Berkut
and Excalibur were clustered into most sensitive and moderately
sensitive genotypes. Finally, the results show that there was a
significantly genetic variation among the eight varieties that were
studied under heat and water stress.
Abstract: The purpose of this paper is to perform a multidisciplinary design and analysis (MDA) of honeycomb panels used in the satellites structural design. All the analysis is based on clamped-free boundary conditions. In the present work, detailed finite element models for honeycomb panels are developed and analysed. Experimental tests were carried out on a honeycomb specimen of which the goal is to compare the previous modal analysis made by the finite element method as well as the existing equivalent approaches. The obtained results show a good agreement between the finite element analysis, equivalent and tests results; the difference in the first two frequencies is less than 4% and less than 10% for the third frequency. The results of the equivalent model presented in this analysis are obtained with a good accuracy. Moreover, investigations carried out in this research relate to the honeycomb plate modal analysis under several aspects including the structural geometrical variation by studying the various influences of the dimension parameters on the modal frequency, the variation of core and skin material of the honeycomb. The various results obtained in this paper are promising and show that the geometry parameters and the type of material have an effect on the value of the honeycomb plate modal frequency.
Abstract: A filter is used to remove undesirable frequency information from a dynamic signal. This paper shows that the Znotch filter filtering technique can be applied to remove the noise nuisance from a machining signal. In machining, the noise components were identified from the sound produced by the operation of machine components itself such as hydraulic system, motor, machine environment and etc. By correlating the noise components with the measured machining signal, the interested components of the measured machining signal which was less interfered by the noise, can be extracted. Thus, the filtered signal is more reliable to be analysed in terms of noise content compared to the unfiltered signal. Significantly, the I-kaz method i.e. comprises of three dimensional graphical representation and I-kaz coefficient, Z∞ could differentiate between the filtered and the unfiltered signal. The bigger space of scattering and the higher value of Z∞ demonstrated that the signal was highly interrupted by noise. This method can be utilised as a proactive tool in evaluating the noise content in a signal. The evaluation of noise content is very important as well as the elimination especially for machining operation fault diagnosis purpose. The Z-notch filtering technique was reliable in extracting noise component from the measured machining signal with high efficiency. Even though the measured signal was exposed to high noise disruption, the signal generated from the interaction between cutting tool and work piece still can be acquired. Therefore, the interruption of noise that could change the original signal feature and consequently can deteriorate the useful sensory information can be eliminated.
Abstract: Nigeria is considered as one of the many countries in
sub-Saharan Africa with a weak economy and gross deficiencies in technology and engineering. Available data from international monitoring and regulatory organizations show that technology is pivotal to determining the economic strengths of nations all over the
world. Education is critical to technology acquisition, development,
dissemination and adaptation. Thus, this paper seeks to critically
assess and discuss issues and challenges facing technological
advancement in Nigeria, particularly in the education sector, and also
proffers solutions to resuscitate the Nigerian education system
towards achieving national technological and economic sustainability
such that Nigeria can compete favourably with other technologicallydriven
economies of the world in the not-too-distant future.