Abstract: Computational fluid dynamics (CFD) simulations
carried out in this paper show that spacer orientation has a major
influence on temperature patterns and on the heat transfer rates. The
local heat flux values significantly vary from high to very low values
at each filament when spacer touches the membrane surface. The
heat flux profile is more uniform when spacer filaments are not in
contact with the membrane thus making this arrangement more
beneficial. The temperature polarization is also found to be less in
this case when compared to the empty channel.
Abstract: The state of melt viscosity in injection process is significantly influenced by the setting parameters due to that the shear rate of injection process is higher than other processes. How to determine plastic melt viscosity during injection process is important to understand the influence of setting parameters on the melt viscosity. An apparatus named as pressure sensor bushing (PSB) module that is used to evaluate the melt viscosity during injection process is developed in this work. The formulations to coupling melt viscosity with fill time and injection pressure are derived and then the melt viscosity is determined. A test mold is prepared to evaluate the accuracy on viscosity calculations between the PSB module and the conventional approaches. The influence of melt viscosity on the tensile strength of molded part is proposed to study the consistency of injection quality.
Abstract: Ant colony based routing algorithms are known to
grantee the packet delivery, but they suffer from the huge overhead
of control messages which are needed to discover the route. In this
paper we utilize the network nodes positions to group the nodes
in connected clusters. We use clusters-heads only on forwarding
the route discovery control messages. Our simulations proved that
the new algorithm has decreased the overhead dramatically without
affecting the delivery rate.
Abstract: The paper presents a one-dimensional transient
mathematical model of thermal oil-water two-phase emulsion flows
in pipes. The set of the mass, momentum and enthalpy conservation
equations for the continuous fluid and droplet phases are solved. Two
friction correlations for the continuous fluid phase to wall friction are
accounted for in the model and tested. The aerodynamic drag force
between the continuous fluid phase and droplets is modeled, too. The
density and viscosity of both phases are assumed to be constant due
to adiabatic experimental conditions. The proposed mathematical
model is validated on the experimental measurements of oil-water
emulsion flows in horizontal pipe [1,2]. Numerical analysis on
single- and two-phase oil-water flows in a pipe is presented in the
paper. The continuous oil flow having water droplets is simulated.
Predictions, which are performed by using the presented model, show
excellent agreement with the experimental data if the water fraction is
equal or less than 10%. Disagreement between simulations and
measurements is increased if the water fraction is larger than 10%.
Abstract: In this paper we present a new method for coin
identification. The proposed method adopts a hybrid scheme using
Eigenvalues of covariance matrix, Circular Hough Transform (CHT)
and Bresenham-s circle algorithm. The statistical and geometrical
properties of the small and large Eigenvalues of the covariance
matrix of a set of edge pixels over a connected region of support are
explored for the purpose of circular object detection. Sparse matrix
technique is used to perform CHT. Since sparse matrices squeeze
zero elements and contain only a small number of non-zero elements,
they provide an advantage of matrix storage space and computational
time. Neighborhood suppression scheme is used to find the valid
Hough peaks. The accurate position of the circumference pixels is
identified using Raster scan algorithm which uses geometrical
symmetry property. After finding circular objects, the proposed
method uses the texture on the surface of the coins called texton,
which are unique properties of coins, refers to the fundamental micro
structure in generic natural images. This method has been tested on
several real world images including coin and non-coin images. The
performance is also evaluated based on the noise withstanding
capability.
Abstract: Isobaric vapor-liquid equilibrium measurements are reported for the binary mixtures of Mesitylene + 1-Heptanol and Mesitylene + 1-Octanol at 97.3 kPa. The measurements have been performed using a vapor recirculating type (modified Othmer's) equilibrium still. Both the mixtures show positive deviation from ideality. The Mesitylene + 1-Heptanol mixture forms an azeotrope whereas Mesitylene + 1- Octanol form a non – azeotropic mixture. The activity coefficients have been calculated taking into consideration the vapor phase nonideality. The data satisfy the thermodynamic consistency tests of Herington, and Hirata. The activity coefficients have been satisfactorily correlated by means of the Margules, Redlich-Kister, Wilson, Black, and NRTL equations. The activity coefficient values have also been obtained by UNIFAC method.
Abstract: Rockfall is a kind of irregular geological disaster. Its
destruction time, space and movements are highly random. The impact
force is determined by the way and velocity rocks move. The
movement velocity of a rockfall depends on slope gradient of its
moving paths, height, slope surface roughness and rock shapes. For
effectively mitigate and prevent disasters brought by rockfalls, it is
required to precisely calculate the moving paths of a rockfall so as to
provide the best protective design. This paper applies Colorado
Rockfall Simulation Program (CRSP) as our study tool to discuss the
impact of slope shape and surface roughness on the moving paths of a
single rockfall. The analytical results showed that the slope, m=1:1,
acted as the threshold for rockfall bounce height on a monoclinal slight
slope. When JRC ´╝£ 1.2, movement velocity reduced and bounce
height increased as JCR increased. If slope fixed and JRC increased,
the bounce height of rocks increased gradually with reducing
movement velocity. Therefore, the analysis on the moving paths of
rockfalls with CRSP could simulate bouncing of falling rocks. By
analyzing moving paths, velocity, and bounce height of falling rocks,
we could effectively locate impact points of falling rocks on a slope.
Such analysis can be served as a reference for future disaster
prevention and control.
Abstract: This paper investigates experimental and numerical study of the airflow characteristics for vortex, round and square ceiling diffusers and its effect on the thermal comfort in a ventilated room. Three different thermal comfort criteria namely; Mean Age of the Air (MAA), ventilation effectiveness (E), and Effective Draft Temperature (EDT) have been used to predict the thermal comfort zone inside the room. In experimental work, a sub-scale room is set-up to measure the temperature field in the room. In numerical analysis, unstructured grids have been used to discretize the numerical domain. Conservation equations are solved using FLUENT commercial flow solver. The code is validated by comparing the numerical results obtained from three different turbulence models with the available experimental data. The comparison between the various numerical models shows that the standard k-ε turbulence model can be used to simulate these cases successfully. After validation of the code, effect of supply air velocity on the flow and thermal field could be investigated and hence the thermal comfort. The results show that the pressure coefficient created by the square diffuser is 1.5 times greater than that created by the vortex diffuser. The velocity decay coefficient is nearly the same for square and round diffusers and is 2.6 times greater than that for the vortex diffuser.
Abstract: Samples of CoFe2-xCrxO4 where x varies from 0.0 to 0.5 were prepared by co-precipitation route. These samples were sintered at 750°C for 2 hours. These particles were characterized by X-ray diffraction (XRD) at room temperature. The FCC spinel structure was confirmed by XRD patterns of the samples. The crystallite sizes of these particles were calculated from the most intense peak by Scherrer formula. The crystallite sizes lie in the range of 37-60 nm. The lattice parameter was found decreasing upon substitution of Cr. DC electrical resistivity was measured as a function of temperature. The room temperature thermoelectric power was measured for the prepared samples. The magnitude of Seebeck coefficient depends on the composition and resistivity of the samples.
Abstract: The goal of this work is to improve the efficiency and the reliability of the automatic artifact rejection, in particular from the Electroencephalographic (EEG) recordings. Artifact rejection is a key topic in signal processing. The artifacts are unwelcome signals that may occur during the signal acquisition and that may alter the analysis of the signals themselves. A technique for the automatic artifact rejection, based on the Independent Component Analysis (ICA) for the artifact extraction and on some high order statistics such as kurtosis and Shannon-s entropy, was proposed some years ago in literature. In this paper we enhance this technique introducing the Renyi-s entropy. The performance of our method was tested exploiting the Independent Component scalp maps and it was compared to the performance of the method in literature and it showed to outperform it.
Abstract: A 1V, 1GHz low noise amplifier (LNA) has been designed and simulated using Spectre simulator in a standard TSMC 0.18um CMOS technology.With low power and noise optimization techniques, the amplifier provides a gain of 24 dB, a noise figure of only 1.2 dB, power dissipation of 14 mW from a 1 V power supply.
Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: The Linear discriminant analysis (LDA) can be
generalized into a nonlinear form - kernel LDA (KLDA) expediently
by using the kernel functions. But KLDA is often referred to a general
eigenvalue problem in singular case. To avoid this complication, this
paper proposes an iterative algorithm for the two-class KLDA. The
proposed KLDA is used as a nonlinear discriminant classifier, and the
experiments show that it has a comparable performance with SVM.
Abstract: The successful use of CDMA technology is based on
the construction of large families of encoding sequences with good
correlation properties. This paper discusses PN sequence generation
based on Residue Arithmetic with an effort to improve the performance
of existing interference-limited CDMA technology for mobile
cellular systems. All spreading codes with residual number system
proposed earlier did not consider external interferences, multipath
propagation, Doppler effect etc. In literature the use of residual
arithmetic in DS-CDMA was restricted to encoding of already spread
sequence; where spreading of sequence is done by some existing
techniques. The novelty of this paper is the use of residual number
system in generation of the PN sequences which is used to spread
the message signal. The significance of cross-correlation factor in
alleviating multi-access interference is also discussed. The RNS based
PN sequence has superior performance than most of the existing
codes that are widely used in DS-CDMA applications. Simulation
results suggest that the performance of the proposed system is
superior to many existing systems.
Abstract: Many medical devices are driven by motor pumps. Some researchers reported that the vibration mainly affected medical devices using a motor pump. The purpose of this study was to examine the effect of stiffness and damping coefficient in a 3-dimensional (3D) model of a motor pump and spring. In the present paper, experimental and mathematical tests for the moments of inertia of the 3D model and the material properties were investigated by an INSTRON machine. The response surfaces could be generated by using 3D multi-body analysis and the design of experiment method. It showed that differences in contours of the response surface were clearly found for the particular area. Displacement of the center of the motor pump was decreased at K≈2000 N/M, C≈12.5 N-sec/M. However, the frequency was increased at K≈2000 N/M, C≈15 N-sec/M. In this study, this study suggested experimental technique for vibration reduction for a motor pump in medical device. The combined method suggested in this study will greatly contribute to design of medical devices concerning vibration and noise intervention.
Abstract: Due to the non- intuitive nature of Quantum
algorithms, it becomes difficult for a classically trained person to
efficiently construct new ones. So rather than designing new
algorithms manually, lately, Genetic algorithms (GA) are being
implemented for this purpose. GA is a technique to automatically
solve a problem using principles of Darwinian evolution. This has
been implemented to explore the possibility of evolving an n-qubit
circuit when the circuit matrix has been provided using a set of
single, two and three qubit gates. Using a variable length population
and universal stochastic selection procedure, a number of possible
solution circuits, with different number of gates can be obtained for
the same input matrix during different runs of GA. The given
algorithm has also been successfully implemented to obtain two and
three qubit Boolean circuits using Quantum gates. The results
demonstrate the effectiveness of the GA procedure even when the
search spaces are large.
Abstract: With the rapid expansion of city scale and the
excessive concentration of population, achieving relative equality of
extracurricular education resources and improving spatial service
performance of relevant facilities become necessary arduous tasks. In
urban space, extracurricular education facilities should offer better
service to its targeted area and promote the equality and efficiency of
education, which is accomplished by the allocation of facilities. Based
on questionnaire and survey for local students in Hangzhou City in
2009, this study classifies extracurricular education facilities in
meg-city and defines the equalization of these facilities. Then it is
suggested to establish extracurricular education facilities system
according to the development level of city and demands of local
students, and to introduce a spatial analysis method into urban
planning through the aspects of spatial distribution, travel cost and
spatial service scope. Finally, the practice of nine sub-districts of
Hangzhou is studied.
Abstract: Nowadays over-consumption of fossil energy in
buildings especially in residential buildings and also considering the
increase in populations, the crisis of energy shortage in a near future
is predictable. The recent performance of developed countries in
construction with the aim of decreasing fossil energies shows that
these countries have understood the incoming crisis and has taken
reasonable and basic actions in this regard. However, Iranian
architecture, with several thousands years of history, has acquired
and executed invaluable experiences in designing, adapting and
coordinating with the nature.
Architectural studies during the recent decades show that imitating
modern western architecture results in high energy wastage beside
the fact that it not reasonably adaptable and corresponded with the
habits and customs of people unlike the architecture in the past which
was compatible and adaptable with the climatic conditions and this
necessitates optimal using of renewable energies more than ever. This
paper studies problems of design, execution and living in today's
houses and reviews the characteristics of climatic elements paying
special attention to the performance of trombe wall and solar
greenhouse in traditional houses and offers some suggestions for
combining these two elements and a climatic strategy.
Abstract: In this study, we developed a model to predict the
temperature and the pressure variation in an internal combustion
engine operated in HCCI (Homogeneous charge compression ignition)
mode. HCCI operation begins from aspirating of homogeneous charge
mixture through intake valve like SI (Spark ignition) engine and the
premixed charge is compressed until temperature and pressure of
mixture reach autoignition point like diesel engine. Combustion phase
was described by double-Wiebe function. The single zone model
coupled with an double-Wiebe function were performed to simulated
pressure and temperature between the period of IVC (Inlet valve close)
and EVO (Exhaust valve open). Mixture gas properties were
implemented using STANJAN and transfer the results to main model.
The model has considered the engine geometry and enables varying in
fuelling, equivalence ratio, manifold temperature and pressure. The
results were compared with the experiment and showed good
correlation with respect to combustion phasing, pressure rise, peak
pressure and temperature. This model could be adapted and use to
control start of combustion for HCCI engine.
Abstract: In the present research, steam cracking of two types of
feedstocks i.e., naphtha and ethane is simulated for Pyrocrack1-1 and
2/2 coil configurations considering two key parameters of coil outlet
temperature (COT) and coil capacity using a radical based kinetic
model. The computer model is confirmed using the industrial data
obtained from Amirkabir Petrochemical Complex. The results are in
good agreement with performance data for naphtha cracking in a
wide range of severity (0.4-0.7), and for ethane cracking on various
conversions (50-70). It was found that Pyrocrack2-2 coil type is an
appropriate choice for steam cracking of ethane at reasonable
ethylene yield while resulting in much lower tube wall temperature
while Pyrocrack1-1 coil type is a proper selection for liquid
feedstocks i.e. naphtha. It can be used for cracking of liquid
feedstocks at optimal ethylene yield whereas not exceeding the
allowable maximum tube temperature.