Abstract: Dengue disease is an infectious vector-borne viral
disease that is commonly found in tropical and sub-tropical regions,
especially in urban and semi-urban areas, around the world and
including Malaysia. There is no currently available vaccine or
chemotherapy for the prevention or treatment of dengue disease.
Therefore prevention and treatment of the disease depend on vector
surveillance and control measures. Disease risk mapping has been
recognized as an important tool in the prevention and control
strategies for diseases. The choice of statistical model used for
relative risk estimation is important as a good model will
subsequently produce a good disease risk map. Therefore, the aim of
this study is to estimate the relative risk for dengue disease based
initially on the most common statistic used in disease mapping called
Standardized Morbidity Ratio (SMR) and one of the earliest
applications of Bayesian methodology called Poisson-gamma model.
This paper begins by providing a review of the SMR method, which
we then apply to dengue data of Perak, Malaysia. We then fit an
extension of the SMR method, which is the Poisson-gamma model.
Both results are displayed and compared using graph, tables and
maps. Results of the analysis shows that the latter method gives a
better relative risk estimates compared with using the SMR. The
Poisson-gamma model has been demonstrated can overcome the
problem of SMR when there is no observed dengue cases in certain
regions. However, covariate adjustment in this model is difficult and
there is no possibility for allowing spatial correlation between risks in
adjacent areas. The drawbacks of this model have motivated many
researchers to propose other alternative methods for estimating the
risk.
Abstract: The objective of this study is to propose an observer design for nonlinear systems by using an augmented linear system derived by application of a formal linearization method. A given nonlinear differential equation is linearized by the formal linearization method which is based on Taylor expansion considering up to the higher order terms, and a measurement equation is transformed into an augmented linear one. To this augmented dimensional linear system, a linear estimation theory is applied and a nonlinear observer is derived. As an application of this method, an estimation problem of transient state of electric power systems is studied, and its numerical experiments indicate that this observer design shows remarkable performances for nonlinear systems.
Abstract: This study investigated the relationship between
exercise imagery use and level of physical activity within a wide
range of exercisers in Klang valley, Malaysia. One hundred and
twenty four respondents (Mage = 28.92, SD = 9.34) completed two
sets of questionnaires (Exercise Imagery Inventory and Leisure-Time
Exercise Questionnaire) that measure the use of imagery and exercise
frequency of participants. From the result obtained, exercise imagery
is found to be significantly correlated to level of physical activity.
Besides that, variables such as gender, age and ethnicity that may
affect the use of imagery and exercise frequency were also being
assessed in this study. Among all variables, only ethnicity showed
significant difference in level of physical activity (p < 0.05). Findings
in this study suggest that further investigation should be done on
other variables such as socioeconomic, educational level, and selfefficacy
that may affect the imagery use and frequency of physical
activity among exercisers.
Abstract: The crop rice is the staple food of most Sierra Leone
with no close substitute. However, its cultivation has been on its last
legs over the years. The decline in the domestic rice cultivation has
had vicious socio-economic implications such as hiking consumer
prices, balance of payment dilemmas with debt burden. The objective
of this study is thus, to assess the effect of the shift of rural labour
towards non-agricultural sectors on rice cultivation. The tools utilized
for analyzing the problem under consideration involved a thorough
descriptive statistics and generalized linear model using OLS
technique. Increased rural population was established positive and
significant in affecting rice cultivation. Fertilizer utilization was
insignificant in rice cultivation. For reducing the shift of rural labor
force towards nonagricultural sectors, the government should make
the agricultural sector very lucrative.
Abstract: Cameron Highlands is a mountainous area subjected
to torrential tropical showers. It extracts 5.8 million liters of water
per day for drinking supply from its rivers at several intake points.
The water quality of rivers in Cameron Highlands, however, has
deteriorated significantly due to land clearing for agriculture,
excessive usage of pesticides and fertilizers as well as construction
activities in rapidly developing urban areas. On the other hand, these
pollution sources known as non-point pollution sources are diverse
and hard to identify and therefore they are difficult to estimate.
Hence, Geographical Information Systems (GIS) was used to provide
an extensive approach to evaluate landuse and other mapping
characteristics to explain the spatial distribution of non-point sources
of contamination in Cameron Highlands. The method to assess
pollution sources has been developed by using Cameron Highlands
Master Plan (2006-2010) for integrating GIS, databases, as well as
pollution loads in the area of study. The results show highest annual
runoff is created by forest, 3.56 × 108 m3/yr followed by urban
development, 1.46 × 108 m3/yr. Furthermore, urban development
causes highest BOD load (1.31 × 106 kgBOD/yr) while agricultural
activities and forest contribute the highest annual loads for
phosphorus (6.91 × 104 kgP/yr) and nitrogen (2.50 × 105 kgN/yr),
respectively. Therefore, best management practices (BMPs) are
suggested to be applied to reduce pollution level in the area.
Abstract: When the foundations of structures under cyclic
loading with amplitudes less than their permissible load, the concern exists often for the amount of uniform and non-uniform settlement of
such structures. Storage tank foundations with numerous filling and discharging and railways ballast course under repeating
transportation loads are examples of such conditions. This paper
deals with the effects of using the new generation of reinforcements,
Grid-Anchor, for the purpose of reducing the permanent settlement
of these foundations under the influence of different proportions of
the ultimate load. Other items such as the type and the number of
reinforcements as well as the number of loading cycles are studied numerically. Numerical models were made using the Plaxis3D
Tunnel finite element code. The results show that by using gridanchor
and increasing the number of their layers in the same
proportion as that of the cyclic load being applied, the amount of
permanent settlement decreases up to 42% relative to unreinforced
condition depends on the number of reinforcement layers and percent
of applied load and the number of loading cycles to reach a constant
value of dimensionless settlement decreases up to 20% relative to
unreinforced condition.
Abstract: In recent years, a number of works proposing the
combination of multiple classifiers to produce a single
classification have been reported in remote sensing literature. The
resulting classifier, referred to as an ensemble classifier, is
generally found to be more accurate than any of the individual
classifiers making up the ensemble. As accuracy is the primary
concern, much of the research in the field of land cover
classification is focused on improving classification accuracy. This
study compares the performance of four ensemble approaches
(boosting, bagging, DECORATE and random subspace) with a
univariate decision tree as base classifier. Two training datasets,
one without ant noise and other with 20 percent noise was used to
judge the performance of different ensemble approaches. Results
with noise free data set suggest an improvement of about 4% in
classification accuracy with all ensemble approaches in
comparison to the results provided by univariate decision tree
classifier. Highest classification accuracy of 87.43% was achieved
by boosted decision tree. A comparison of results with noisy data
set suggests that bagging, DECORATE and random subspace
approaches works well with this data whereas the performance of
boosted decision tree degrades and a classification accuracy of
79.7% is achieved which is even lower than that is achieved (i.e.
80.02%) by using unboosted decision tree classifier.
Abstract: Minimally invasive surgery (MIS) is now being widely used as a preferred choice for various types of operations. The need to detect various tactile properties, justifies the key role of tactile sensing that is currently missing in MIS. In this regard, Laparoscopy is one of the methods of minimally invasive surgery that can be used in kidney stone removal surgeries. At this moment, determination of the exact location of stone during laparoscopy is one of the limitations of this method that no scientific solution has been found for so far. Artificial tactile sensing is a new method for obtaining the characteristics of a hard object embedded in a soft tissue. Artificial palpation is an important application of artificial tactile sensing that can be used in different types of surgeries. In this study, a new method for determining the exact location of stone during laparoscopy is presented. In the present study, the effects of stone existence on the surface of kidney were investigated using conceptual 3D model of kidney containing a simulated stone. Having imitated palpation and modeled it conceptually, indications of stone existence that appear on the surface of kidney were determined. A number of different cases were created and solved by the software and using stress distribution contours and stress graphs, it is illustrated that the created stress patterns on the surface of kidney show not only the existence of stone inside, but also its exact location. So three-dimensional analysis leads to a novel method of predicting the exact location of stone and can be directly applied to the incorporation of tactile sensing in artificial palpation, helping surgeons in non-invasive procedures.
Abstract: In this study, we propose a network architecture for
providing secure access to information resources of enterprise
network from remote locations in a wireless fashion. Our proposed
architecture offers a very promising solution for organizations which
are in need of a secure, flexible and cost-effective remote access
methodology. Security of the proposed architecture is based on
Virtual Private Network technology and a special role based access
control mechanism with location and time constraints. The flexibility
mainly comes from the use of Internet as the communication medium
and cost-effectiveness is due to the possibility of in-house
implementation of the proposed architecture.
Abstract: The study in this paper underlines the importance of
correct joint selection of the spreading codes for uplink of multicarrier
code division multiple access (MC-CDMA) at the transmitter
side and detector at the receiver side in the presence of nonlinear
distortion due to high power amplifier (HPA). The bit error rate
(BER) of system for different spreading sequences (Walsh code, Gold
code, orthogonal Gold code, Golay code and Zadoff-Chu code) and
different kinds of receivers (minimum mean-square error receiver
(MMSE-MUD) and microstatistic multi-user receiver (MSF-MUD))
is compared by means of simulations for MC-CDMA transmission
system. Finally, the results of analysis will show, that the application
of MSF-MUD in combination with Golay codes can outperform
significantly the other tested spreading codes and receivers for all
mostly used models of HPA.
Abstract: This article presents the simulation, parameterization and optimization of an electromagnet with the C–shaped configuration, intended for the study of magnetic properties of materials. The electromagnet studied consists of a C-shaped yoke, which provides self–shielding for minimizing losses of magnetic flux density, two poles of high magnetic permeability and power coils wound on the poles. The main physical variable studied was the static magnetic flux density in a column within the gap between the poles, with 4cm2 of square cross section and a length of 5cm, seeking a suitable set of parameters that allow us to achieve a uniform magnetic flux density of 1x104 Gaussor values above this in the column, when the system operates at room temperature and with a current consumption not exceeding 5A. By means of a magnetostatic analysis by the finite element method, the magnetic flux density and the distribution of the magnetic field lines were visualized and quantified. From the results obtained by simulating an initial configuration of electromagnet, a structural optimization of the geometry of the adjustable caps for the ends of the poles was performed. The magnetic permeability effect of the soft magnetic materials used in the poles system, such as low– carbon steel (0.08% C), Permalloy (45% Ni, 54.7% Fe) and Mumetal (21.2% Fe, 78.5% Ni), was also evaluated. The intensity and uniformity of the magnetic field in the gap showed a high dependence with the factors described above. The magnetic field achieved in the column was uniform and its magnitude ranged between 1.5x104 Gauss and 1.9x104 Gauss according to the material of the pole used, with the possibility of increasing the magnetic field by choosing a suitable geometry of the cap, introducing a cooling system for the coils and adjusting the spacing between the poles. This makes the device a versatile and scalable tool to generate the magnetic field necessary to perform magnetic characterization of materials by techniques such as vibrating sample magnetometry (VSM), Hall-effect, Kerr-effect magnetometry, among others. Additionally, a CAD design of the modules of the electromagnet is presented in order to facilitate the construction and scaling of the physical device.
Abstract: This paper presents comparative study on recent
integer DCTs and a new method to construct a low sensitive structure
of integer DCT for colored input signals. The method refers to
sensitivity of multiplier coefficients to finite word length as an
indicator of how word length truncation effects on quality of output
signal. The sensitivity is also theoretically evaluated as a function of
auto-correlation and covariance matrix of input signal. The structure of
integer DCT algorithm is optimized by combination of lower sensitive
lifting structure types of IRT. It is evaluated by the sensitivity of
multiplier coefficients to finite word length expression in a function of
covariance matrix of input signal. Effectiveness of the optimum
combination of IRT in integer DCT algorithm is confirmed by quality
improvement comparing with existing case. As a result, the optimum
combination of IRT in each integer DCT algorithm evidently improves
output signal quality and it is still compatible with the existing one.
Abstract: The increasing importance of data stream arising in a
wide range of advanced applications has led to the extensive study of
mining frequent patterns. Mining data streams poses many new
challenges amongst which are the one-scan nature, the unbounded
memory requirement and the high arrival rate of data streams. In this
paper, we propose a new approach for mining itemsets on data
stream. Our approach SFIDS has been developed based on FIDS
algorithm. The main attempts were to keep some advantages of the
previous approach and resolve some of its drawbacks, and
consequently to improve run time and memory consumption. Our
approach has the following advantages: using a data structure similar
to lattice for keeping frequent itemsets, separating regions from each
other with deleting common nodes that results in a decrease in search
space, memory consumption and run time; and Finally, considering
CPU constraint, with increasing arrival rate of data that result in
overloading system, SFIDS automatically detect this situation and
discard some of unprocessing data. We guarantee that error of results
is bounded to user pre-specified threshold, based on a probability
technique. Final results show that SFIDS algorithm could attain
about 50% run time improvement than FIDS approach.
Abstract: Hexavalent chromium is highly toxic to most living organisms and a known human carcinogen by the inhalation route of exposure. Therefore, treatment of Cr(VI) contaminated wastewater is essential before their discharge to the natural water bodies. Cr(VI) reduction to Cr(III) can be beneficial because a more mobile and more toxic chromium species is converted to a less mobile and less toxic form. Zero-valence-state metals, such as scrap iron, can serve as electron donors for reducing Cr(VI) to Cr(III). The influence of pH on scrap iron capacity to reduce Cr(VI) was investigated in this study. Maximum reduction capacity of scrap iron was observed at the beginning of the column experiments; the lower the pH, the greater the experiment duration with maximum scrap iron reduction capacity. The experimental results showed that highest maximum reduction capacity of scrap iron was 12.5 mg Cr(VI)/g scrap iron, at pH 2.0, and decreased with increasing pH up to 1.9 mg Cr(VI)/g scrap iron at pH = 7.3.
Abstract: This study compares three meta heuristics to minimize makespan (Cmax) for Hybrid Flow Shop (HFS) Scheduling Problem with Parallel Machines. This problem is known to be NP-Hard. This study proposes three algorithms among improvement heuristic searches which are: Genetic Algorithm (GA), Simulated Annealing (SA), and Tabu Search (TS). SA and TS are known as deterministic improvement heuristic search. GA is known as stochastic improvement heuristic search. A comprehensive comparison from these three improvement heuristic searches is presented. The results for the experiments conducted show that TS is effective and efficient to solve HFS scheduling problems.
Abstract: Interpretation of aerial images is an important task in
various applications. Image segmentation can be viewed as the essential
step for extracting information from aerial images. Among many
developed segmentation methods, the technique of clustering has been
extensively investigated and used. However, determining the number
of clusters in an image is inherently a difficult problem, especially
when a priori information on the aerial image is unavailable. This
study proposes a support vector machine approach for clustering
aerial images. Three cluster validity indices, distance-based index,
Davies-Bouldin index, and Xie-Beni index, are utilized as quantitative
measures of the quality of clustering results. Comparisons on the
effectiveness of these indices and various parameters settings on the
proposed methods are conducted. Experimental results are provided
to illustrate the feasibility of the proposed approach.
Abstract: This study deals with evaluation of influence of salinity (NaCl) onto equilibrium of Cu and Ni removal from aqueous solutions by natural sorbent – zeolite. Equilibrium data were obtained by batch experiments. The salinity of the aqueous solution was influenced by dissolving NaCl in distilled water. It was studied in the range of NaCl concentrations from 1 g.l-1 to 100g.l-1. For Cu sorption there is a significant influence of salinity. The maximum capacity of zeolite for Cu was decreasing with growing concentration of NaCl. For Ni sorption there is not so significant influence of salinity as for Cu. The maximum capacity of zeolite for Ni was slightly decreasing with growing concentration of NaCl.
Abstract: The purpose of this study is to examine the self and
decision making levels of students receiving education in schools of
physical training and sports. The population of the study consisted
258 students, among which 152 were male and 106 were female
( X age=19,3713 + 1,6968), that received education in the schools of
physical education and sports of Selcuk University, Inonu University,
Gazi University and Karamanoglu Mehmetbey University. In order to
achieve the purpose of the study, the Melbourne Decision Making
Questionnary developed by Mann et al. (1998) [1] and adapted to
Turkish by Deniz (2004) [2] and the Self-Esteem Scale developed by
Aricak (1999) [3] was utilized. For analyzing and interpreting data
Kolmogorov-Smirnov test, t-test and one way anova test were used,
while for determining the difference between the groups Tukey test
and Multiple Linear Regression test were employed and significance
was accepted at P
Abstract: In view of their importance and usefulness in reliability theory and probability distributions, several generalizations of the inverse Gaussian distribution and the Krtzel function are investigated in recent years. This has motivated the authors to introduce and study a new generalization of the inverse Gaussian distribution and the Krtzel function associated with a product of a Bessel function of the third kind )(zKQ and a Z - Fox-Wright generalized hyper geometric function introduced in this paper. The introduced function turns out to be a unified gamma-type function. Its incomplete forms are also discussed. Several properties of this gamma-type function are obtained. By means of this generalized function, we introduce a generalization of inverse Gaussian distribution, which is useful in reliability analysis, diffusion processes, and radio techniques etc. The inverse Gaussian distribution thus introduced also provides a generalization of the Krtzel function. Some basic statistical functions associated with this probability density function, such as moments, the Mellin transform, the moment generating function, the hazard rate function, and the mean residue life function are also obtained.KeywordsFox-Wright function, Inverse Gaussian distribution, Krtzel function & Bessel function of the third kind.
Abstract: In many buildings we rely on large footings to offer
structural stability. Designers often compensate for the lack of
knowledge available with regard to foundation-soil interaction by
furnishing structures with overly large footings. This may lead to a
significant increase in building expenditures if many large
foundations are present. This paper describes the interface material
law that governs the behavior along the contact surface of adjacent
materials, and the behavior of a large foundation under ultimate limit
loading. A case study is chosen that represents a common
foundation-soil system frequently used in general practice and
therefore relevant to other structures. Investigations include
compressing versus uplifting wind forces, alterations to the
foundation size and subgrade compositions, the role of the slab
stiffness and presence and the effect of commonly used structural
joints and connections. These investigations aim to provide the
reader with an objective design approach, efficiently preventing
structural instability.