Abstract: Dispersions of casein micelles (CM) were studied at a
constant protein concentration of 5 wt % in high NaCl environment
ranging from 0% to 12% by Dynamic light scattering (DLS) and
Fourier Transform Infrared (FTIR). The rehydration profiles obtained
were interpreted in term of wetting, swelling and dispersion stages by
using a turbidity method. Two behaviours were observed depending
on the salt concentration. The first behaviour (low salt concentration)
presents a typical rehydration profile with a significant change
between 3 and 6% NaCl indicating quick wetting, swelling and long
dispersion stage. On the opposite, the dispersion stage of the second
behaviour (high salt concentration) was significantly shortened
indicating a strong modification of the protein backbone. A salt
increase result to a destabilization of the micelle and the formation of
mini-micelles more or less aggregated indicating an average micelles
size ranging from 100 to 200 nm. For the first time, the estimations
of secondary structural elements (irregular, ß-sheet, α-helix and turn)
by the Amide III assignments were correlated with results from
Amide I.
Abstract: This paper presents preliminary results regarding system-level power awareness for FPGA implementations in wireless sensor networks. Re-configurability of field programmable gate arrays (FPGA) allows for significant flexibility in its applications to embedded systems. However, high power consumption in FPGA becomes a significant factor in design considerations. We present several ideas and their experimental verifications on how to optimize power consumption at high level of designing process while maintaining the same energy per operation (low-level methods can be used additionally). This paper demonstrates that it is possible to estimate feasible power consumption savings even at the high level of designing process. It is envisaged that our results can be also applied to other embedded systems applications, not limited to FPGA-based.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: The modeling of inelastic behavior of plastic materials requires measurements providing information on material response to different multiaxial loading conditions. Different triaxiality conditions and values of Lode parameters have to be
covered for complex description of the material plastic behavior.
Samples geometries providing material plastic behavoiur over the range of interest are proposed with the use of FEM analysis. Round samples with 3 different notches and smooth surface are used
together with butterfly type of samples tested at angle ranging for 0 to
90°. Identification of ductile damage parameters is carried out on
the basis of obtained experimental data for austenitic stainless steel.
The obtained material plastic damage parameters are subsequently applied to FEM simulation of notched CT normally samples used for
fracture mechanics testing and results from the simulation are
compared with real tests.
Abstract: In order to alleviate the mental and physical problems
of persons with disabilities, animal-assisted therapy (AAT) is one of
the possible modalities that employs the merit of the human-animal
interaction. Nevertheless, to achieve the purpose of AAT for persons
with severe disabilities (e.g. spinal cord injury, stroke, and
amyotrophic lateral sclerosis), real-time animal language
interpretation is desirable. Since canine behaviors can be visually
notable from its tail, this paper proposes the automatic real-time
interpretation of canine tail language for human-canine interaction in
the case of persons with severe disabilities. Canine tail language is
captured via two 3-axis accelerometers. Directions and frequencies
are selected as our features of interests. The novel fuzzy rules based
on Gaussian-Trapezoidal model and center of gravity (COG)-based
defuzzification method are proposed in order to interpret the features
into four canine emotional behaviors, i.e., agitate, happy, scare and
neutral as well as its blended emotional behaviors. The emotional
behavior model is performed in the simulated dog and has also been
evaluated in the real dog with the perfect recognition rate.
Abstract: There is growing interest in biodiesel (fatty acid
methyl ester or FAME) because of the similarity in its properties
when compared to those of diesel fuels. Diesel engines operated on
biodiesel have lower emissions of carbon monoxide, unburned
hydrocarbons, particulate matter, and air toxics than when operated
on petroleum-based diesel fuel. Production of fatty acid methyl ester
(FAME) from rapeseed (nonedible oil) fatty acid distillate having
high free fatty acids (FFA) was investigated in this work. Conditions
for esterification process of rapeseed oil were 1.8 % H2SO4 as
catalyst, MeOH/oil of molar ratio 2 : 0.1 and reaction temperature
65 °C, for a period of 3h. The yield of methyl ester was > 90 % in 1
h.
The amount of FFA was reduced from 93 wt % to less than 2 wt %
at the end of the esterification process. The FAME was pureed by
neutralization with 1 M sodium hydroxide in water solution at a
reaction temperature of 62 °C. The final FAME product met with the
biodiesel quality standard, and ASTM D 6751.
Abstract: Detection of squirrel cage induction motor (SCIM) broken bars has long been an important but difficult job in the detection area of motor faults. Early detection of this abnormality in the motor would help to avoid costly breakdowns. A new detection method based on particle swarm optimization (PSO) is presented in this paper. Stator current in an induction motor will be measured and characteristic frequency components of faylted rotor will be detected by minimizing a fitness function using pso. Supply frequency and side band frequencies and their amplitudes can be estimated by the proposed method. The proposed method is applied to a faulty motor with one and two broken bars in different loading condition. Experimental results prove that the proposed method is effective and applicable.
Abstract: This research investigates the suitability of fuel oil in
improving gypseous soil. A detailed laboratory tests were carried-out
on two soils (soil I with 51.6% gypsum content, and soil II with
26.55%), where the two soils were obtained from Al-Therthar site
(Al-Anbar Province-Iraq).
This study examines the improvement of soil properties using the
gypsum material which is locally available with low cost to minimize
the effect of moisture on these soils by using the fuel oil. This study
was conducted on two models of the soil gypsum, from the Tharthar
area. The first model was sandy soil with Gypsum content of (51.6%)
and the second is clayey soil and the content of Gypsum is (26.55%).
The program included tests measuring the permeability and
compressibility of the soil and their collapse properties. The shear
strength of the soil and the amounts of weight loss of fuel oil due to
drying had been found. These tests have been conducted on the
treated and untreated soils to observe the effect of soil treatment on
the engineering properties when mixed with varying degrees of fuel
oil with the equivalent of the water content.
The results showed that fuel oil is a good material to modify the
basic properties of the gypseous soil of collapsibility and
permeability, which are the main problems of this soil and retained
the soil by an appropriate amount of the cohesion suitable for
carrying the loads from the structure.
Abstract: In the present work, we propose a new projection method for solving the matrix equation AXB = F. For implementing our new method, generalized forms of block Krylov subspace and global Arnoldi process are presented. The new method can be considered as an extended form of the well-known global generalized minimum residual (Gl-GMRES) method for solving multiple linear systems and it will be called as the extended Gl-GMRES (EGl- GMRES). Some new theoretical results have been established for proposed method by employing Schur complement. Finally, some numerical results are given to illustrate the efficiency of our new method.
Abstract: We study the typical domain size and configuration
character of a randomly perturbed system exhibiting continuous
symmetry breaking. As a model system we use rod-like objects
within a cubic lattice interacting via a Lebwohl–Lasher-type
interaction. We describe their local direction with a headless unit
director field. An example of such systems represents nematic LC or
nanotubes. We further introduce impurities of concentration p, which
impose the random anisotropy field-type disorder to directors. We
study the domain-type pattern of molecules as a function of p,
anchoring strength w between a neighboring director and impurity,
temperature, history of samples. In simulations we quenched the
directors either from the random or homogeneous initial
configuration. Our results show that a history of system strongly
influences: i) the average domain coherence length; and ii) the range
of ordering in the system. In the random case the obtained order is
always short ranged (SR). On the contrary, in the homogeneous case,
SR is obtained only for strong enough anchoring and large enough
concentration p. In other cases, the ordering is either of quasi long
range (QLR) or of long range (LR). We further studied memory
effects for the random initial configuration. With increasing external
ordering field B either QLR or LR is realized.
Abstract: Inadequate curriculum for software engineering is considered to be one of the most common software risks. A number of solutions, on improving Software Engineering Education (SEE) have been reported in literature but there is a need to collectively present these solutions at one place. We have performed a mapping study to present a broad view of literature; published on improving the current state of SEE. Our aim is to give academicians, practitioners and researchers an international view of the current state of SEE. Our study has identified 70 primary studies that met our selection criteria, which we further classified and categorized in a well-defined Software Engineering educational framework. We found that the most researched category within the SE educational framework is Innovative Teaching Methods whereas the least amount of research was found in Student Learning and Assessment category. Our future work is to conduct a Systematic Literature Review on SEE.
Abstract: We study how the outcome of evolutionary dynamics on
graphs depends on a randomness on the graph structure. We gradually
change the underlying graph from completely regular (e.g. a square lattice) to completely random. We find that the fixation probability increases as the randomness increases; nevertheless, the increase is
not significant and thus the fixation probability could be estimated by the known formulas for underlying regular graphs.
Abstract: In this paper, we present a novel objective nonreference performance assessment algorithm for image fusion. It takes into account local measurements to estimate how well the important information in the source images is represented by the fused image. The metric is based on the Universal Image Quality Index and uses the similarity between blocks of pixels in the input images and the fused image as the weighting factors for the metrics. Experimental results confirm that the values of the proposed metrics correlate well with the subjective quality of the fused images, giving a significant improvement over standard measures based on mean squared error and mutual information.
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: We have developed a computer program consisting of
6 subtests assessing the children hand dexterity applicable in the
rehabilitation medicine. We have carried out a normative study on a
representative sample of 285 children aged from 7 to 15 (mean age
11.3) and we have proposed clinical standards for three age groups
(7-9, 9-11, 12-15 years). We have shown statistical significance of
differences among the corresponding mean values of the task time
completion. We have also found a strong correlation between the task
time completion and the age of the subjects, as well as we have
performed the test-retest reliability checks in the sample of 84
children, giving the high values of the Pearson coefficients for the
dominant and non-dominant hand in the range 0.740.97 and
0.620.93, respectively.
A new MATLAB-based programming tool aiming at analysis of
cardiologic RR intervals and blood pressure descriptors, is worked
out, too. For each set of data, ten different parameters are extracted: 2
in time domain, 4 in frequency domain and 4 in Poincaré plot
analysis. In addition twelve different parameters of baroreflex
sensitivity are calculated. All these data sets can be visualized in time
domain together with their power spectra and Poincaré plots. If
available, the respiratory oscillation curves can be also plotted for
comparison. Another application processes biological data obtained
from BLAST analysis.
Abstract: Key performance indicators (KPIs) are used for post
result evaluation in the construction industry, and they normally do
not have provisions for changes. This paper proposes a set of
dynamic key performance indicators (d-KPIs) which predicts the
future performance of the activity being measured and presents the
opportunity to change practice accordingly. Critical to the
predictability of a construction project is the ability to achieve
automated data collection. This paper proposes an effective way to
collect the process and engineering management data from an
integrated construction management system. The d-KPI matrix,
consisting of various indicators under seven categories, developed
from this study can be applied to close monitoring of the
development projects of aged-care facilities. The d-KPI matrix also
enables performance measurement and comparison at both project
and organization levels.
Abstract: This paper reports the influence of sucrose on the
preservation of CO2 hydrate crystal samples. The particle diameter of
hydrate samples were 1.0 and 5.6-8.0 mm. Mass fraction of sucrose in
the sample was 0.16. The samples were stored at the aerated condition
under atmospheric pressure and at the temperature of 253 or 258 K.
The results indicated that the mass fractions of CO2 hydrate in the
samples with sucrose were 0.10 ± 0.03 at the end of 3-week
preservation, regardless of temperature and particle diameter. Mass
fraction of CO2 hydrate in the samples with sucrose was higher than
that of pure CO2 hydrate for 1.0 mm particle diameter, while was
lower than that of pure CO2 hydrate for 5.6-8.0 mm particle diameter.
Discussion is made on the influence of sucrose on the dissociation of
CO2 hydrate and the resulting formation of ice.
Abstract: The effect of teaching method on learning
assistance Dunn Review .The study, to compare the effects of
collaboration on teaching mathematics learning courses, including
writing, science, experimental girl students by other methods of
teaching basic first paid and the amount of learning students
methods have been trained to cooperate with other students with
other traditional methods have been trained to compare. The
survey on 100 students in Tehran that using random sampling ¬
cluster of girl students between the first primary selections was
performed. Considering the topic of semi-experimental research
methods used to practice the necessary information by
questionnaire, examination questions by the researcher, in
collaboration with teachers and view authority in this field and
related courses that teach these must have been collected.
Research samples to test and control groups were divided.
Experimental group and control group collaboration using
traditional methods of mathematics courses, including writing and
experimental sciences were trained. Research results using
statistical methods T is obtained in two independent groups show
that, through training assistance will lead to positive results and
student learning in comparison with traditional methods, will
increase also led to collaboration methods increase skills to solve
math lesson practice, better understanding and increased skill
level of students in practical lessons such as science and has been
writing.
Abstract: Long number multiplications (n ≥ 128-bit) are a
primitive in most cryptosystems. They can be performed better by
using Karatsuba-Ofman technique. This algorithm is easy to
parallelize on workstation network and on distributed memory, and
it-s known as the practical method of choice. Multiplying long
numbers using Karatsuba-Ofman algorithm is fast but is highly
recursive. In this paper, we propose different designs of
implementing Karatsuba-Ofman multiplier. A mixture of sequential
and combinational system design techniques involving pipelining is
applied to our proposed designs. Multiplying large numbers can be
adapted flexibly to time, area and power criteria. Computationally
and occupation constrained in embedded systems such as: smart
cards, mobile phones..., multiplication of finite field elements can be
achieved more efficiently. The proposed designs are compared to
other existing techniques. Mathematical models (Area (n), Delay (n))
of our proposed designs are also elaborated and evaluated on
different FPGAs devices.
Abstract: A special case of floating point data representation is block
floating point format where a block of operands are forced to have a joint
exponent term. This paper deals with the finite wordlength properties of
this data format. The theoretical errors associated with the error model for
block floating point quantization process is investigated with the help of error
distribution functions. A fast and easy approximation formula for calculating
signal-to-noise ratio in quantization to block floating point format is derived.
This representation is found to be a useful compromise between fixed point
and floating point format due to its acceptable numerical error properties over
a wide dynamic range.