Abstract: Reverse Logistics (RL) Network is considered as
complex and dynamic network that involves many stakeholders such
as: suppliers, manufactures, warehouse, retails and costumers, this
complexity is inherent in such process due to lack of perfect
knowledge or conflicting information. Ontologies on the other hand
can be considered as an approach to overcome the problem of sharing
knowledge and communication among the various reverse logistics
partners. In this paper we propose a semantic representation based on
hybrid architecture for building the Ontologies in ascendant way, this
method facilitates the semantic reconciliation between the
heterogeneous information systems that support reverse logistics
processes and product data.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.
Abstract: Pipe failure and leakage is a problematic issue and the
traditional solution of replacing the pipes is costly and time
consuming. Rehabilitation by relining materials based on polymer
composites is an alternative solution towards the degradation problem
of the old piping. This paper provides a brief summary of advances in
technology, methods and materials for relining as well as a summary
of the degradation analyses of the two main composite materials used
for relining, rubber filled epoxy and reinforced polyester baltoflake
when they are exposed in deionized water and elevated temperature
up to 80°C for a duration of 2-14 months in the laboratory.
Abstract: Laser beam welding of dissimilar sheet metal
combinations such as Ti/Al, SS/Al and Cu/Al are increasingly
demanded due to high energy densities with less fusion and heat
affected zones. A good weld joint strength involves combinations of
dissimilar metals and the formation of solid solution in the weld pool.
Many metal pairs suffer from significant intermetallic phase
formation during welding which greatly reduces their strength. The
three different sheet metal mentioned above is critically reviewed and
phase diagram for the combinations are given. The aim of this study
is to develop an efficient metal combinations and the influence on
their interfacial characteristics. For that the following parameters
such as weld geometry, residual distortion, micro hardness,
microstructure and mechanical properties are analyzed
systematically.
Abstract: An existing RC building in Madinah is seismically
evaluated with and without infill wall. Four model systems have been
considered i.e. model I (no infill), model IIA (strut infill-update from
field test), model IIB (strut infill- ASCE/SEI 41) and model IIC (strut
infill-Soft storey- ASCE/SEI 41). Three dimensional pushover
analyses have been carried out using SAP2000 software
incorporating inelastic material behavior for concrete, steel and infill
walls. Infill wall has been modeled as equivalent strut according to
suggested equation matching field test measurements and to the
ASCE/SEI 41 equation. The effect of building modeling on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madinah area has been investigated. The
response modification factor (R) for the 5 story RC building is
evaluated from capacity and demand spectra (ATC-40) for the
studied models. The results are summarized and discussed.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: The contact resistance between source/drain electrodes
and semiconductor layer is an important parameter affecting electron
transporting performance in the thin film transistor (TFT). In this
work, we introduced a transparent and the solution prossable
single-walled carbon nanotube (SWCNT)/Al-doped ZnO nano particle
(AZO NP) bilayer electrodes showing low contact resistance with
indium-oxide (In2O3) sol gel thin film. By inserting low work function
AZO NPs into the interface between the SWCNTs and the In2O3 which
has a high energy barrier, we could obtain an electrical Ohmic contact
between them. Finally, with the SWCNT-AZO NP bilayer electrodes,
we successfully fabricated a TFT showing a field effect mobility of
5.38 cm2/V·s at 250°C.
Abstract: The idea of the asynchronous transmission in
wavelength division multiplexing (WDM) ring MANs is studied in
this paper. Especially, we present an efficient access technique to
coordinate the collisions-free transmission of the variable sizes of IP
traffic in WDM ring core networks. Each node is equipped with a
tunable transmitter and a tunable receiver. In this way, all the
wavelengths are exploited for both transmission and reception. In
order to evaluate the performance measures of average throughput,
queuing delay and packet dropping probability at the buffers, a
simulation model that assumes symmetric access rights among the
nodes is developed based on Poisson statistics. Extensive numerical
results show that the proposed protocol achieves apart from high
bandwidth exploitation for a wide range of offered load, fairness of
queuing delay and dropping events among the different packets size
categories.
Abstract: Contracting authorities in the public sector are
obligated to apply the principles provided for in the Polish law for the
evaluation and selection of contractors. In order to analyse the
methods of contractors selecting applied in practice by public clients,
the notices of contract award results for construction works were
analysed. The analysis shows that the procedure selected more and
more often is open competitive bidding, where the assessment of the
competence of contractors is not very precise, as well as noncompetitive
bidding, i.e. single source procurement. The share of
procurement procedures, where the only criterion is price, is
increasing. The solution to the problems existing here might be the
introduction of one of the forms of pre-selection of contractors. The
article also briefly discusses verification systems for companies
applying for public contracts used in EU countries.
Abstract: Complexation of anthocyanins to mimic natural
copigmentation process was investigated. Cyanidin-rich extracts from
Zea mays L. ceritina Kulesh. and delphinidin-rich extracts from
Clitoria ternatea L. were used to form 4 anthocyanin complexes,
AC1, AC2, AC3 and AC4, in the presence of several polyphenols and
a trace metal. Characterizations of the ACs were conducted by UV,
FTIR, DSC/TGA and morphological observations. Bathochromic
shifts of the UV spectra of 4 formulas of ACs were observed at peak
wavelengths of about 510-620 nm by 10 nm suggesting complex
formation. FTIR spectra of the ACs indicate shifts of peaks from
1,733 cm-1 to 1,696 cm-1 indicating interactions and a decrease in the
peak areas within the wavenumber of 3,400-3,500 cm-1 indicating
changes in hydrogen bonding. Thermal analysis of all of the ACs
suggests increases in melting temperature after complexation. AC
with the highest melting temperature was morphologically observed
by SEM and TEM to be crystal-like particles within a range of 50 to
200 nm. Particle size analysis of the AC by laser diffraction gave a
range of 50-600 nm, indicating aggregation. This AC was shown to
have no cytotoxic effect on cultured HGEPp0.5 and HGF (all p>
0.05) by MTT. Therefore, complexation of anthocyanins was simple
and self-assembly process, potentially resulting in nanosized particles
of anthocyanin complex.
Abstract: Anthocyanins are natural pigments with effective UV
protection but their topical use could be limited due to their
physicochemical characteristics. An attempt to overcome such
limitations by complexation of 2 major anthocyanin-rich sources, C.
ternatea and Z. mays, has potentiated its use as topical antiinflammatory.
Cell studies indicate no cytotoxicity of the
anthocyanin complex (AC) up to 1 mg/ml tested in HaCaT and
human fore head fibroblasts by MTT. Croton oil-induced ear edema
in Wistar rats suggests an effective dose of 5 mg/cm2 of AC as a
topical anti-inflammatory in comparison to 0.5 mg/cm2 of
fluocinolone acetonide. Niosomal encapsulation of the AC
significantly prolonged the anti-inflammatory activity particularly at
8 h after topical application (p = 0.0001). The AC was not cytotoxic
and its anti-inflammatory and activity was dose-dependent and
prolonged by niosomal encapsulation. It has also shown to promote
collagen type 1 production in cell culture. Thus, AC could be a
potential candidate for topical anti-inflammatory agent from natural
resources.
Abstract: Food is widely packaged with plastic materials to
prevent microbial contamination and spoilage. Ionizing radiation is
widely used to sterilize the food-packaging materials. Sterilization by
γ-radiation causes degradation such as embrittlement, stiffening,
softening, discoloration, odour generation, and decrease in molecular
weight. Many antioxidants can prevent γ-degradation but most of
them are toxic. The migration of antioxidants to its environment
gives rise to major concerns in case of food packaging plastics. In
this attempt, we have aimed to utilize synergistic mixtures of
stabilizers which are approved for food-contact applications.
Ethylene-propylene-diene terpolymer has been melt-mixed with
hindered amine stabilizers (HAS), phenolic antioxidants and organophosphites
(hydroperoxide decomposer). Results were discussed by
comparing the stabilizing efficiency of mixtures with and without
phenol system. Among phenol containing systems where we mostly
observed discoloration due to the oxidation of hindered phenol, the
combination of secondary HAS, tertiary HAS, organo-phosphite and
hindered phenol exhibited improved stabilization efficiency than
single or binary additive systems. The mixture of secondary HAS and
tertiary HAS, has shown antagonistic effect of stabilization.
However, the combination of organo-phosphite with secondary HAS,
tertiary HAS and phenol antioxidants have been found to give
synergistic even at higher doses of Gamma-irradiation. The effects
have been explained through the interaction between the stabilizers.
After γ-irradiation, the consumption of oligomeric stabilizer
significantly depends on the components of stabilization mixture. The
effect of the organo-phosphite antioxidant on the overall stability has
been discussed.
Abstract: Liver disorders are one of the major problems of the
world. Despite its frequent occurrence, high morbidity and high
mortality, its medical management is currently inadequate. This study
was designed to evaluate the hepatoprotective effect of saponin
extract of the root of Garcinia kola on the integrity of the liver of
paracetamol induced wistar albino rats. Twenty five (25) male adult
wistar albino rats were divided into five (5) groups. Group I was the
Control group that received distilled water only, group II was the
negative control that received 2 g/kg of paracetamol on the 13th day,
and group III, IV and V were pre-treated with 100, 200 and
400mg/kg of the saponin extract before inducing the liver damage on
the 13th day with 2 g/kg of paracetamol. Twenty four (24) h after
administration, the rats were sacrificed and blood samples were
collected. The serum Alanine Transaminase (ALT), Aspartate
Transaminase (AST), Alkaline Phosphatase (ALP) activities,
Bilirubin and conjugated bilirubin, glucose and protein
concentrations were evaluated. The liver was fixed immediately in
Formalin and was processed and stained in Haematoxylin and Eosin
(H&E). Administration of saponin extract from the root of Garcinia
kola significantly decreased paracetamol induced elevated enzymes
in the test group. Also histological observations showed that saponin
extract of the root of Garcinia kola exhibited a significant liver
protection against the toxicant as evident by the cells trying to return
to normal. Saponin extract from the root of Garcinia kola indicated a
protection of structural integrity of the hepatocytic cell membrane
and regeneration of the damaged liver.
Abstract: The present study was done to evaluate the presence
of tetracycline resistance genes in Lactococcus garvieae isolated
from cultured rainbow trout, West Iran. The isolates were examined
for antimicrobial resistance using disc diffusion method. Of the 49
strains tested, 19 were resistant to tetracycline (38.7%), 32 to
enrofloxacin (65.3%), 21 to erythromycin (42.8%), 20 to
chloramphenicol and trimetoprim-sulfamethoxazole (40.8%). The
strains were then characterized for their genotypic resistance profiles.
The results revealed that all 49 isolates contained at least one of the
tetracycline resistance genes. Tet (A) was found in 89.4% of
tetracycline resistant isolates and the frequency of other gene were as
follows: tet (E) 42.1%, tet (B) 47.3%, tet (D) 15.7%, tet (L) 26.3%,
tet (K) 52.6%, tet (G) 36.8%, tet (34) 21%, tet (S) 63.1%, tet (C)
57.8%, tet (M) 73.6%, tet (O) 42.1%. The results revealed high levels
of antibiotic resistance in L. garvieae strains which is a potential
danger for trout culture as well as for public health.
Abstract: This study presents synthesis of novel block
copolymers of thienyl end capped ethoxylated nonyl phenol and
pyrrole via chemical oxidative polymerization. Ethoxylated nonyl
phenol (ENP) was reacted with 2-thiophenecarbonyl chloride in order
to synthesize a macromonomer containing thienyl end-group (ENPThC).
Then copolymers of ENP-ThC and pyrrole were synthesized
by chemical oxidative polymerization using iron (III) chloride as an
oxidant. ENP-ThC served both as a macromonomer and an emulsifier
for pyrrole with poor solubility in water.
The synthesized block copolymers (ENP-ThC-b-PPy) were
characterized by spectroscopic analysis and the electrical
conductivities were investigated with 4-point probe technique.
Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: Adsorption of a boron nitride nanotube (BNNT) was
examined toward ethylacetylene (C4H6) molecule by using density
functional theory (DFT) calculations at the B3LYP/6-31G (d) level,
and it was found that the adsorption energy (Ead) of ethylacetylene
the pristine nanotubes is about -1.60kcal/mol. But when nanotube has
been doped with Si and Al atoms, the adsorption energy of
ethylacetylene molecule was increased. Calculation showed that
when the nanotube is doping by Al, the adsorption energy is about -
24.19kcal/mol and also the amount of HOMO/LUMO energy gap
(Eg) will reduce significantly. Boron nitride nanotube is a suitable
adsorbent for ethylacetylene and can be used in separation processes
ethylacetylene. It is seem that nanotube (BNNT) is a suitable
semiconductor after doping, and the doped BNNT in the presence of
ethylacetylene an electrical signal is generating directly and therefore
can potentially be used for ethylacetylene sensors.
Abstract: In order to better understand the long term
implications of the grout wear failure mode in large-diameter plainsided
grouted connections, a numerical model has been developed
and calibrated that can take advantage of existing operational plant
data to predict the wear accumulation for the actual load conditions
experienced over a given period, thus limiting the requirement for
expensive monitoring systems. This model has been derived and
calibrated based on site structural condition monitoring (SCM) data
and supervisory control and data acquisition systems (SCADA) data
for two operational wind turbine generator substructures afflicted
with this challenge, along with experimentally derived wear rates.
Abstract: A mixed method by combining modified pole
clustering technique and modified cauer continued fraction is
proposed for reducing the order of the large-scale dynamic systems.
The denominator polynomial of the reduced order model is obtained
by using modified pole clustering technique while the coefficients of
the numerator are obtained by modified cauer continued fraction.
This method generated 'k' number of reduced order models for kth
order reduction. The superiority of the proposed method has been
elaborated through numerical example taken from the literature and
compared with few existing order reduction methods.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.