Abstract: An envelope echo signal measurement is proposed in
this paper using echo signal observation from the 200 kHz echo
sounder receiver. The envelope signal without any object is compared
with the envelope signal of the sphere. Two diameter size steel ball
(3.1 cm & 2.2 cm) and two diameter size air filled stainless steel ball
(4.8 cm & 7.4 cm) used in this experiment. The target was positioned
about 0.5 m and 1.0 meter from the transducer face using nylon rope.
From the echo observation in time domain, it is obviously shown that
echo signal structure is different between the size, distance and type
of metal sphere. The amplitude envelope voltage for the bigger
sphere is higher compare to the small sphere and it confirm that the
bigger sphere have higher target strength compare to the small
sphere. Although the structure signal without any object are different
compare to the signal from the sphere, the reflected signal from the
tank floor increase linearly with the sphere size. We considered this
event happened because of the object position approximately to the
tank floor.
Abstract: Amongst the consistently fluctuating conditions
prevailing today, changeability represents a strategic key factor for a
manufacturing company to achieve success on the international
markets. In order to cope with turbulences and the increasing level of
incalculability, not only the flexible design of production systems but
in particular the employee as enabler of change provide the focus
here. It is important to enable employees from manufacturing
companies to participate actively in change events and in change
decisions. To this end, the learning factory has been created, which is
intended to serve the development of change-promoting competences
and the sensitization of employees for the necessity of changes.
Abstract: This paper applies an anthropological approach to illuminate the dynamic cultural geography of Kazakhstani Korean ethnicity focusing on its turning point, the historic “Seoul Olympic Games in 1988." The Korean ethnic group was easily considered as a harmonious and homogeneous community by outsiders, but there existed deep-seated conflicts and hostilities within the ethnic group. The majority-s oppositional dichotomy of superiority and inferiority toward the minority was continuously reorganized and reinforced by difference in experience, memory and sentiment. However, such a chronic exclusive boundary was collapsed following the patriotism ignited by the Olympics held in their mother country. This paper explores the fluidity of subject by formation of the boundary in which constructed cultural differences are continuously essentialized and reproduced, and by dissolution of cultural barrier in certain contexts.
Abstract: A computer model of Quantum Theory (QT) has been
developed by the author. Major goal of the computer model was
support and demonstration of an as large as possible scope of QT.
This includes simulations for the major QT (Gedanken-) experiments
such as, for example, the famous double-slit experiment.
Besides the anticipated difficulties with (1) transforming exacting
mathematics into a computer program, two further types of problems
showed up, namely (2) areas where QT provides a complete mathematical
formalism, but when it comes to concrete applications the
equations are not solvable at all, or only with extremely high effort;
(3) QT rules which are formulated in natural language and which do
not seem to be translatable to precise mathematical expressions, nor
to a computer program.
The paper lists problems in all three categories and describes also
the possible solutions or circumventions developed for the computer
model.
Abstract: Does open ended creative technology give positive impact in learning design? Although there are many researchers had examined on the impact of technology on design education but there are very few conclusive researches done on the impact of open ended used of software to learning design. This paper sought to investigate a group of student-s experience on relatively wider range of software application within the context of design project. A typography design project was used to create a learning environment with the aim of inculcate design skills into the learners and increase their creative problem-solving and critical thinking skills. The methods used in this study were questionnaire survey and personal observation which will be focus on the individual and group response during the completion of the task.
Abstract: Nowadays, under developed countries for progress in
science and technology and decreasing the technologic gap with
developed countries, increasing the capacities and technology
transfer from developed countries. To remain competitive, industry is
continually searching for new methods to evolve their products.
Business model is one of the latest buzzwords in the Internet and
electronic business world. To be successful, organizations must look
into the needs and wants of their customers. This research attempts to
identify a specific feature of the company with a strong competitive
advantage by analyzing the cause of Customer satisfaction. Due to
the rapid development of knowledge and information technology,
business environments have become much more complicated.
Information technology can help a firm aiming to gain a competitive
advantage. This study explores the role and effect of Information
Communication Technology in Business Models and Customer
satisfaction on firms and also relationships between ICTs and
Outsourcing strategic.
Abstract: This paper analysed the food security situation among
Nigerian rural farmers. Data collected on 202 rural farmers from
Benue State were analysed using descriptive and inferential statistics.
The study revealed that majority of the respondents (60.83%) had
medium dietary diversity. Furthermore, household daily calorie
requirement for the food secure households was 10,723 and the
household daily calorie consumption was 12,598, with a surplus
index of 0.04. The food security index was 1.16. The Household
daily per capita calorie consumption was 3,221.2. For the food
insecure households, the household daily calorie requirement was
20,213 and the household daily calorie consumption was 17,393. The
shortfall index was 0.14. The food security index was 0.88. The
Household daily per capita calorie consumption was 2,432.8. The
most commonly used coping strategies during food stress included
intercropping (99.2%), reliance on less preferred food (98.1%),
limiting portion size at meal times (85.8%) and crop diversification
(70.8%).
Abstract: The paper is intended to declare and apply ethics, i. e.
moral principles, rules in marketing environment. Ethical behavior of
selected pharmaceutical companies in the Slovak Republic is the
object of our research. The aim of our research is to determine
perception of ethical behavior of the pharmaceutical industry in
Slovakia by the medicine representatives in comparison with the
assessment of doctors and patients. The experimental sample
included 90 participants who were divided into three groups:
medicine representatives of the pharmaceutical companies (N=30),
doctors (N=30) and patients (N=30). The research method was a
Questionnaire of ethical behavior, created by us, that describes
individual areas included in the Code of ethics of the pharmaceutical
industry in Slovakia. The results showed influence of professional
status on ethical behavior perception, not gender. Higher perception
was indicated at patients rather than doctors and medicine
representatives.
Abstract: This research proposes a Preemptive Possibilistic
Linear Programming (PPLP) approach for solving multiobjective
Aggregate Production Planning (APP) problem with interval demand
and imprecise unit price and related operating costs. The proposed
approach attempts to maximize profit and minimize changes of
workforce. It transforms the total profit objective that has imprecise
information to three crisp objective functions, which are maximizing
the most possible value of profit, minimizing the risk of obtaining the
lower profit and maximizing the opportunity of obtaining the higher
profit. The change of workforce level objective is also converted.
Then, the problem is solved according to objective priorities. It is
easier than simultaneously solve the multiobjective problem as
performed in existing approach. Possible range of interval demand is
also used to increase flexibility of obtaining the better production
plan. A practical application of an electronic company is illustrated to
show the effectiveness of the proposed model.
Abstract: The aim of the study was to follow changes of powervelocity
relationship in female volleyball players during an annual
training cycle. The study was conducted on eleven female volleyball
players: age 21.6±1.7 years, body height 177.9±4.7 cm, body mass
71.3±6.6 kg and training experience 8.6±3.3 years. Power–velocity
relationship was determined from five maximal 10-second
cycloergometer efforts with external loads equal: 2.5, 5.0, 7.5, 10.0
and 12.5% of body weight (BW) before (I) and after (II) the
preparatory period, after the first (III) and second (IV) competitive
season. The maximal power output increased from 9.30±0.85 W•kg–1
(I) to 9.50±0.96 W•kg–1 (II), 9.77±0.96 W•kg–1 (III) and 9.95±1.13
W•kg–1 (IV, p
Abstract: The purpose of this study is to find natural gait of
biped robot such as human being by analyzing the COG (Center Of
Gravity) trajectory of human being's gait. It is discovered that human
beings gait naturally maintain the stability and use the minimum
energy. This paper intends to find the natural gait pattern of biped
robot using the minimum energy as well as maintaining the stability by
analyzing the human's gait pattern that is measured from gait image on
the sagittal plane and COG trajectory on the frontal plane. It is not
possible to apply the torques of human's articulation to those of biped
robot's because they have different degrees of freedom. Nonetheless,
human and 5-link biped robots are similar in kinematics. For this, we
generate gait pattern of the 5-link biped robot by using the GA
algorithm of adaptation gait pattern which utilize the human's ZMP
(Zero Moment Point) and torque of all articulation that are measured
from human's gait pattern. The algorithm proposed creates biped
robot's fluent gait pattern as that of human being's and to minimize
energy consumption because the gait pattern of the 5-link biped robot
model is modeled after consideration about the torque of human's each
articulation on the sagittal plane and ZMP trajectory on the frontal
plane. This paper demonstrate that the algorithm proposed is superior
by evaluating 2 kinds of the 5-link biped robot applied to each gait
patterns generated both in the general way using inverse kinematics
and in the special way in which by considering visuality and
efficiency.
Abstract: One way for optimum loading of overdimensioning
conveyers is speed (capacity) decrement, with attention for
production capabilities and demands. At conveyers which drives with
three phase slip-ring induction motor, technically reasonable solution
for conveyer (driving motors) speed regulation is using constant
torque subsynchronous cascade with static semiconductor converter
and transformer for energy reversion to the power network. In the
paper is described mathematical model for parameter calculation of
two-motors 6 kV subsynchronous cascade. It is also demonstrated
that applying of this cascade gave several good properties, foremost
in electrical energy saving, also in improving of other energy
indexes, and finally that results in cost reduction of complete
electrical motor drive.
Abstract: In this paper we investigated a number of the Internet
congestion control algorithms that has been developed in the last few
years. It was obviously found that many of these algorithms were
designed to deal with the Internet traffic merely as a train of
consequent packets. Other few algorithms were specifically tailored
to handle the Internet congestion caused by running media traffic that
represents audiovisual content. This later set of algorithms is
considered to be aware of the nature of this media content. In this
context we briefly explained a number of congestion control
algorithms and hence categorized them into the two following
categories: i) Media congestion control algorithms. ii) Common
congestion control algorithms. We hereby recommend the usage of
the media congestion control algorithms for the reason of being
media content-aware rather than the other common type of
algorithms that blindly manipulates such traffic. We showed that the
spread of such media content-aware algorithms over Internet will
lead to better congestion control status in the coming years. This is
due to the observed emergence of the era of digital convergence
where the media traffic type will form the majority of the Internet
traffic.
Abstract: Several trillion cigarettes produced worldwide annually lead to many thousands of kilograms of toxic waste. Cigarette butts (CBs) accumulate in the environment due to the poor biodegradability of the cellulose acetate filters. This paper presents some of the results from a continuing study on recycling CBs into fired clay bricks. Physico-mechanical properties of fired clay bricks manufactured with different percentages of CBs are reported and discussed. The results show that the density of fired bricks was reduced by up to 30 %, depending on the percentage of CBs incorporated into the raw materials. Similarly, the compressive strength of bricks tested decreased according to the percentage of CBs included in the mix. The thermal conductivity performance of bricks was improved by 51 and 58 % for 5 and 10 % CBs content respectively. Leaching tests were carried out to investigate the levels of possible leachates of heavy metals from the manufactured clay-CB bricks. The results revealed trace amounts of heavy metals.
Abstract: Sandwich panels are widely used in the construction
industry for their ease of assembly, light weight and efficient thermal
performance. They are composed of two RC thin outer layers
separated by an insulating inner layer. In this research the inner
insulating layer is made of lightweight Autoclaved Aerated Concrete
(AAC) blocks which has good thermal insulation properties and yet
possess reasonable mechanical strength. The shear strength of the
AAC infill is relied upon to replace the traditionally used insulating
foam and to provide the shear capacity of the panel. A
comprehensive experimental program was conducted on full scale
sandwich panels subjected to bending. In this paper, detailed
numerical modeling of the tested sandwich panels is reported. Nonlinear
3-D finite element modeling of the composite action of the
sandwich panel is developed using ANSYS. Solid elements with
different crashing and cracking capabilities and different constitutive
laws were selected for the concrete and the AAC. Contact interface
elements are used in this research to adequately model the shear
transfer at the interface between the different layers. The numerical
results showed good correlation with the experimental ones
indicating the adequacy of the model in estimating the loading
capacity of panels.
Abstract: Experiments were conducted to characterize fire
properties of wood exposed to the certain external heat flux and
under variety of wood moisture content. Six kinds of Indonesian
wood: keruing, sono, cemara, kamper, pinus, and mahoni were
exposed to radiant heat from a conical heater, result in appearance of
a stable flame on the wood surface caused by spontaneous ignition. A
thermocouple K-type was used to measure the wood surface
temperature. Temperature histories were recorded throughout each
experiment at 1 s intervals using a TC-08. Data of first ignition time
and temperature, end ignition time and temperature, and charring rate
have been successfully collected. It was found that the ignition
temperature and charring rate depend on moisture content of wood.
Abstract: Failure modes and effects analysis (FMEA) is an effective technique for preventing potential problems and actions needed to error cause removal. On the other hand, the oil producing companies paly a critical role in the oil industry of Iran as a developing country out of which, Sepahan Oil Co. has a considerable contribution. The aim of this research is to show how FMEA could be applied and improve the quality of products at Sepahan Oil Co. For this purpose, the four liter production line of the company has been selected for investigation. The findings imply that the application of FMEA has reduced the scraps from 50000 ppm to 5000 ppm and has resulted in a 0.92 percent decrease of the oil waste.
Abstract: The number of cross-border student between Hong
Kong and mainland China is increasing due to an increase of
cross-border marriage between Hong Kong and mainland China. Since
the education system is different to the mainland China, the statue
Since all the children who have the right of abode in Hong Kong
entitle to have free education in Hong Kong, many of the cross-border
family prefer to send the children back to Hong Kong for their
education.
Abstract: This paper gives an overview of how an OWL
ontology has been created to represent template knowledge models
defined in CML that are provided by CommonKADS.
CommonKADS is a mature knowledge engineering methodology
which proposes the use of template knowledge model for knowledge
modelling. The aim of developing this ontology is to present the
template knowledge model in a knowledge representation language
that can be easily understood and shared in the knowledge
engineering community. Hence OWL is used as it has become a
standard for ontology and also it already has user friendly tools for
viewing and editing.
Abstract: Vector quantization is a powerful tool for speech
coding applications. This paper deals with LPC Coding of speech
signals which uses a new technique called Multi Switched Split
Vector Quantization (MSSVQ), which is a hybrid of Multi, switched,
split vector quantization techniques. The spectral distortion
performance, computational complexity, and memory requirements
of MSSVQ are compared to split vector quantization (SVQ), multi
stage vector quantization(MSVQ) and switched split vector
quantization (SSVQ) techniques. It has been proved from results that
MSSVQ has better spectral distortion performance, lower
computational complexity and lower memory requirements when
compared to all the above mentioned product code vector
quantization techniques. Computational complexity is measured in
floating point operations (flops), and memory requirements is
measured in (floats).