Abstract: Monitoring and control of cane sugar crystallization
processes depend on the stability of the supersaturation (σ ) state.
The most widely used information to represent σ is the electrical
conductivity κ of the solutions. Nevertheless, previous studies point
out the shortcomings of this approach: κ may be regarded as
inappropriate to guarantee an accurate estimation of σ in impure
solutions. To improve the process control efficiency, additional
information is necessary. The mass of crystals in the solution ( c m )
and the solubility (mass ratio of sugar to water / s w m m ) are relevant
to complete information. Indeed, c m inherently contains information
about the mass balance and / s w m m contains information about the
supersaturation state of the solution. The main problem is that c m
and / s w m m are not available on-line. In this paper, a model based
soft-sensor is presented for a final crystallization stage (C sugar).
Simulation results obtained on industrial data show the reliability of
this approach, c m and the crystal content ( cc ) being estimated with
a sufficient accuracy for achieving on-line monitoring in industry
Abstract: An evolutionary computing technique for solving initial value problems in Ordinary Differential Equations is proposed in this paper. Neural network is used as a universal approximator while the adaptive parameters of neural networks are optimized by genetic algorithm. The solution is achieved on the continuous grid of time instead of discrete as in other numerical techniques. The comparison is carried out with classical numerical techniques and the solution is found with a uniform accuracy of MSE ≈ 10-9 .
Abstract: Materials added to the matrix help improving operating properties of a composite. This experimental study has targeted to investigate this aim where Silicon Oxide particles were added to glass fibre and epoxy resin at an amount of 15% to the main material to obtain a sort of new composite material. Erosive wear behavior of epoxy-resin dipped composite materials reinforced with glass fibre and Silicon Oxide under three different impingement angles (30°, 60° and 90°), three different impact velocities (23, 34 and 53 m/s), two different angular Aluminum abrasive particle sizes (approximately 200 and 400 μm) and the fibre orientation of 45° (45/-45) were investigated. In the test results, erosion rates were obtained as functions of impingement angles, impact velocities, particle sizes and fibre orientation. Moreover, materials with addition of Silicon Oxide filler material exhibited lower wear as compared to neat materials with no added filler material. In addition, SEM views showing worn out surfaces of the test specimens were scrutinized.
Abstract: In order to study the effect of phosphate solubilization
microorganisms (PSM) and plant growth promoting rhizobacteria
(PGPR) on yield and yield components of corn Zea mays (L. cv.
SC604) an experiment was conducted at research farm of Sari
Agricultural Sciences and Natural Resources University, Iran during
2007. Experiment laid out as split plot based on randomized
complete block design with three replications. Three levels of
manures (consisted of 20 Mg.ha-1 farmyard manure, 15 Mg.ha-1 green
manure and check or without any manures) as main plots and eight
levels of biofertilizers (consisted of 1-NPK or conventional fertilizer
application; 2-NPK+PSM+PGPR; 3 NP50%K+PSM+PGPR; 4-
N50%PK+PSM +PGPR; 5-N50%P50%K+PSM+ PGPR; 6-PK+PGPR; 7-
NK+PSM and 8-PSM+PGPR) as sub plots were treatments. Results
showed that farmyard manure application increased row number, ear
weight, grain number per ear, grain yield, biological yield and
harvest index compared to check. Furthermore, using of PSM and
PGPR in addition to conventional fertilizer applications (NPK) could
improve ear weight, row number and grain number per row and
ultimately increased grain yield in green manure and check plots.
According to results in all fertilizer treatments application of PSM
and PGPR together could reduce P application by 50% without any
significant reduction of grain yield. However, this treatment could
not compensate 50% reduction of N application.
Abstract: The abnormal increase in the number of applications available for download in Android markets is a good indication that they are being reused. However, little is known about their real reusability potential. A considerable amount of these applications is reported as having a poor quality or being malicious. Hence, in this paper, an approach to measure the reusability potential of classes in Android applications is proposed. The approach is not meant specifically for this particular type of applications. Rather, it is intended for Object-Oriented (OO) software systems in general and aims also to provide means to discard the classes of low quality and defect prone applications from being reused directly through inheritance and instantiation. An empirical investigation is conducted to measure and rank the reusability potential of the classes of randomly selected Android applications. The results obtained are thoroughly analyzed in order to understand the extent of this potential and the factors influencing it.
Abstract: Evaluation of crop plants resistance to environmental
stresses specially in germination stage is a critical factor in their
selection in different conditions of cultivation. Therefore use of a
procedure in controllable situation can help to evaluate plants
reaction to stress quickly and precisely. In order to study germination
characteristics of flax in water and salinity stress conditions were
conducted two laboratories experimental. The two experimental were
conducted in 4-replicant completing random design for salinity and
water stress. The treatment, for salinity and water stress was three
potential (zero, 40, 80 mM) of NaCl and three potential (zero, -2, -4
bar) of PEG respectively. Germination percentage and rate, in
addition to Radical and plumule length and dry-weight and
plumule/Radical ration were measured. All of characteristics reduce
under water stress conditions. salinity stress significant reduce
germination rate and Radical and plumule length of flax seeds.
Hydropriming and osmopriming significant increased germination
rate, plumule length and plumule/Radical ration ration of flax seeds.
But germination percentage and Radical and plumule dry weight
significant increased only in hydropriming treat. Hydropriming and
osmopriming could not be used to improved germination under saline
and drought stress. But has more tolerance in salinity and drought
stress in flax by less reduce in Radical and plumule length under
saline and drought stress.
Abstract: By utilizing the system of the recurrence equations, containing two parameters, the dynamics of two antagonistically interconnected populations is studied. The following areas of the system behavior are detected: the area of the stable solutions, the area of cyclic solutions occurrence, the area of the accidental change of trajectories of solutions, and the area of chaos and fractal phenomena. The new two-dimensional diagram of the dynamics of the solutions change (the fractal cabbage) has been obtained. In the cross-section of this diagram for one of the equations the well-known Feigenbaum tree of doubling has been noted.Keywordsbifurcation, chaos, dynamics of populations, fractals
Abstract: The Egyptian Bacillus thuringiensis isolate (M5) produce crystal proteins that is toxic against insects was irradiated with UV light to induce mutants. Upon testing 10 of the resulting mutants for their toxicity against cotton leafworm larvae, the three mutants 62, 64 and 85 proved to be the most toxic ones. Upon testing these mutants along with their parental isolate by SDS-PAGE analysis of spores-crystals proteins as well as vegetative cells proteins, new induced bands appeared in the three mutants by UV radiation and also they showed disappearance of some other bands as compared with the wild type isolate. Multiplex PCR technique, with five sets of specific primers, was used to detect the three types of cryI genes cryIAa, cryIAb and cryIAc. Results showed that these three genes exist, as distinctive bands, in the wild type isolate (M5) as well as in mutants 62 and 85, while the mutant 64 had two distinctive bands of cryIAb and cryIAc genes, and a faint band of cryI Aa gene. Finally, these results revealed that mutant 62 is considered as the promising mutant since it is UV resistant, highly toxic against Spodoptera littoralis and active against a wide range of Lepidopteran insects.
Abstract: There is limited evidence from various countries
about the possible impact of various criteria to be used to determine
the scope of the IFRS for SMEs issued in 2009 and, research is
needed in this area. We provide evidence from Romania, an
emerging economy member of the European Union. The aim of this
paper is to analyze in a local setting if size is a relevant factor for
deciding between local and global standards for SMEs. Our results
indicate that size is a moderate indicator of the existence of possible
users interested in financial statements and that there is a difference
between the scopes of the standard determined on various criteria..
Also, we suggest that the international exposure is quite reduced in
the case of SMEs, but is sufficient to suggest that at least some SMEs
would benefit from international comparability of financial
statements
Abstract: Network reconfiguration is an operation to modify the
network topology. The implementation of network reconfiguration
has many advantages such as loss minimization, increasing system
security and others. In this paper, two topics about the network
reconfiguration in distribution system are briefly described. The first
topic summarizes its impacts while the second explains some
heuristic optimization techniques for solving the network
reconfiguration problem.
Abstract: The purpose of this research was to study the
motivation factors to influence the decision to choose Thai Fabric. A
multiple-stage sample was utilized to collect 400 samples from
working women who had diverse occupations all over Thailand. This
research was a quantitative analysis and questionnaire was used a tool
to collect data. Descriptive statistics used in this research included
percentage, average, and standard deviation and inferential statistics
included hypothesis testing of one way ANOVA.
The research findings revealed that demographic factors and social
factors had an influence to the positive idea of wearing Thai fabric (F
= 5.377, P value < 0.05). The respondents who had the age over 41
years old had a better positive idea of wearing Thai fabric than other
groups. Moreover, the findings revealed that age had influenced the
positive idea of wearing Thai fabric (F = 3.918, P value < 0.05). The
respondents who had the age over 41 years old also had stronger
believe that wearing Thai fabric to work and social gatherings are
socially acceptable than other groups.
Abstract: This research was conducted in the Lower Ping River
Basin downstream of the Bhumibol Dam and the Lower Wang River
Basin in Tak Province, Thailand. Most of the tributary streams of the
Ping can be considered as ungauged catchments. There are 10-
pumping station installation at both river banks of the Ping in Tak
Province. Recently, most of them could not fully operate due to the
water amount in the river below the level that would be pumping,
even though included water from the natural river and released flow
from the Bhumibol Dam. The aim of this research was to increase the
performance of those pumping stations using weir projects in the
Ping. Therefore, the river analysis system model (HEC-RAS) was
applied to study the hydraulic behavior of water surface profiles in
the Ping River with both cases of existing conditions and proposed
weirs during the violent flood in 2011 and severe drought in 2013.
Moreover, the hydrologic modeling system (HMS) was applied to
simulate lateral streamflow hydrograph from ungauged catchments of
the Ping. The results of HEC-RAS model calibration with existing
conditions in 2011 showed best trial roughness coefficient for the
main channel of 0.026. The simulated water surface levels fitted to
observation data with R2 of 0.8175. The model was applied to 3
proposed cascade weirs with 2.35 m in height and found surcharge
water level only 0.27 m higher than the existing condition in 2011.
Moreover, those weirs could maintain river water levels and increase
of those pumping performances during less river flow in 2013.
Abstract: In recent years, real estate prediction or valuation has
been a topic of discussion in many developed countries. Improper
hype created by investors leads to fluctuating prices of real estate,
affecting many consumers to purchase their own homes. Therefore,
scholars from various countries have conducted research in real estate
valuation and prediction. With the back-propagation neural network
that has been popular in recent years and the orthogonal array in the
Taguchi method, this study aimed to find the optimal parameter
combination at different levels of orthogonal array after the system
presented different parameter combinations, so that the artificial
neural network obtained the most accurate results. The experimental
results also demonstrated that the method presented in the study had a
better result than traditional machine learning. Finally, it also showed
that the model proposed in this study had the optimal predictive effect,
and could significantly reduce the cost of time in simulation operation.
The best predictive results could be found with a fewer number of
experiments more efficiently. Thus users could predict a real estate
transaction price that is not far from the current actual prices.
Abstract: This paper explores the importance of privacy in a
contemporary online world. Crucial to the discussion is the idea of
the Lacanian postmodern fragmented self and the problem of how to
ensure that we have room to fully explore various aspects of our
personalities in an environment which is–or at least feels--safe and
free from observation by others. The paper begins with an
exploration of the idea of the self with particular regard to the ways
in which contemporary life and technology seems to have multiplied
the various faces or masks which we present in different contexts. A
brief history of privacy and surveillance follows. Finally, the paper
ends with an affirmation of the importance of private space as an
essential component of our spiritual and emotional well-being in
today-s wired world.
Abstract: Fluid flow in cylinders of elliptic cross-section was investigated. Fluid used is Liquefied petroleum gas (LPG). LPG found in Nigeria contains majorly butane with percentages of propane. Commercial available code FLUENT which uses finite volume method was used to solve fluid flow governing equations. There has been little attention paid to fluid flow in cylindrical elliptic pipes. The present work aims to predict the LPG gas flow in cylindrical pipes of elliptic cross-section. Results of flow parameters of velocity and pressure distributions are presented. Results show that the pressure drop in elliptic pipes is higher than circular pipe of the same cross-sectional area. This is an important result as the pressure drop is related to the pump power needed to drive the flow. Results show that the velocity increases towards centre of the pipe as the flow moves downstream, and also increases towards the outlet of the pipe.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: Nowadays the construction industry is growing specially among developing counties. Iran also has a critical role in these industries in terms of workers disorders. Work-related musculoskeletal disorders (WMSDs) assign 7% of the whole diseases in the society, which make some limitations. One of the main factors, which are ended to WMSDs, is awkward posture. Steel bar bending is considered as one of the prominent performance among construction workers. In this case study we conducted to find the major tasks of bar benders and the most important related risk factors. This study was carried out among twenty workers (18-45 years) as our volunteer samples in some construction sites with less than 6 floors in two regions of Tehran municipality. The data was gathered through in depth observation, interview and questionnaire. Also postural analysis was done by OWAS. In another part of study we used NMQ for gathering some data about psychosocial effects of work related disorders. Our findings show that 64% of workers were not aware of work risks, also about 59% of workers had troubles in their wrists, hands, and especially among workers who worked in steel bar bending. In 46% cases low back pain were prevalence. Considering with gathered data and results, awkward postures and long term tasks and its duration are known as the main risk factors in WMSDs among construction workers, so work-rest schedule and also tools design should be considered to make an ergonomic condition for the mentioned workers.
Abstract: This work presents the hydrogen production from
steam gasification of palm kernel shell (PKS) at 700 oC in the
presence of 5% Ni/BEA and 5% Fe/BEA as catalysts. The steam
gasification was performed in two-staged reactors to evaluate the
effect of calcinations temperature and the steam to biomass ratio on
the product gas composition. The catalytic activity of Ni/BEA
catalyst decreases with increasing calcinations temperatures from 500
to 700 oC. The highest H2 concentration is produced by Fe/BEA
(600) with more than 71 vol%. The catalytic activity of the catalysts
tested is found to correspond to its physicochemical properties. The
optimum range for steam to biomass ratio if found to be between 2 to
4. Excess steam content results in temperature drop in the gasifier
which is undesirable for the gasification reactions.
Abstract: Creation of information society, or in other words, a
society based on knowledge, has wide consequences, both on
individual and complete society, and in general – on a economy of
one country. Development and implementation of ICT represents a
stimulant for economic growth. On individual level, knowledge,
skills and information gathered using ICT, are expanding individual
possibilities of persons, enabling them to have access to timely
sensitive information, such as market prices or investment
conditions, possibilities to access Government-s or private
development funds, etc. By doing so, productivity is increased both
on individual and national level and therefore social wellbeing in
general. In one word, creation of information society - a knowledge
society is happening.
This work will describe challenges and strategies that will follow
the development as well as obstacles in creating information society
– knowledge society in Montenegro.
Abstract: This paper presents a study of laminar to turbulent transition on a profile specifically designed for wind turbine blades, the DU91-W2-250, which belongs to a class of wind turbine dedicated airfoils, developed by Delft University of Technology. A comparison between the experimental behavior of the airfoil studied at Delft wind tunnel and the numerical predictions of the commercial CFD solver ANSYS FLUENT® has been performed. The prediction capabilities of the Spalart-Allmaras turbulence model and of the γ-θ Transitional model have been tested. A sensitivity analysis of the numerical results to the spatial domain discretization has also been performed using four different computational grids, which have been created using the mesher GAMBIT®. The comparison between experimental measurements and CFD results have allowed to determine the importance of the numerical prediction of the laminar to turbulent transition, in order not to overestimate airfoil friction drag due to a fully turbulent-regime flow computation.