Abstract: In the present study, response surface methodology has been used to optimize turn-assisted deep cold rolling process of AISI 4140 steel. A regression model is developed to predict surface hardness and surface roughness using response surface methodology and central composite design. In the development of predictive model, deep cold rolling force, ball diameter, initial roughness of the workpiece, and number of tool passes are considered as model variables. The rolling force and the ball diameter are the significant factors on the surface hardness and ball diameter and numbers of tool passes are found to be significant for surface roughness. The predicted surface hardness and surface roughness values and the subsequent verification experiments under the optimal operating conditions confirmed the validity of the predicted model. The absolute average error between the experimental and predicted values at the optimal combination of parameter settings for surface hardness and surface roughness is calculated as 0.16% and 1.58% respectively. Using the optimal processing parameters, the surface hardness is improved from 225 to 306 HV, which resulted in an increase in the near surface hardness by about 36% and the surface roughness is improved from 4.84µm to 0.252 µm, which resulted in decrease in the surface roughness by about 95%. The depth of compression is found to be more than 300µm from the microstructure analysis and this is in correlation with the results obtained from the microhardness measurements. Taylor hobson talysurf tester, micro vickers hardness tester, optical microscopy and X-ray diffractometer are used to characterize the modified surface layer.
Abstract: A sensory network consists of multiple detection
locations called sensor nodes, each of which is tiny, featherweight
and portable. A single path routing protocols in wireless sensor
network can lead to holes in the network, since only the nodes
present in the single path is used for the data transmission. Apart
from the advantages like reduced computation, complexity and
resource utilization, there are some drawbacks like throughput,
increased traffic load and delay in data delivery. Therefore, multipath
routing protocols are preferred for WSN. Distributing the traffic
among multiple paths increases the network lifetime. We propose a
scheme, for the data to be transmitted through a dominant path to
save energy. In order to obtain a high delivery ratio, a basic route
reconstruction protocol is utilized to reconstruct the path whenever a
failure is detected. A basic reconstruction routing (BRR) algorithm is
proposed, in which a node can leap over path failure by using the
already existing routing information from its neighbourhood while
the composed data is transmitted from the source to the sink. In order
to save the energy and attain high data delivery ratio, data is
transmitted along a multiple path, which is achieved by BRR
algorithm whenever a failure is detected. Further, the analysis of
how the proposed protocol overcomes the drawback of the existing
protocols is presented. The performance of our protocol is compared
to AOMDV and energy efficient node-disjoint multipath routing
protocol (EENDMRP). The system is implemented using NS-2.34.
The simulation results show that the proposed protocol has high
delivery ratio with low energy consumption.
Abstract: Biodiesel as an alternative diesel fuel is steadily gaining more attention and significance. However, there are some drawbacks while using biodiesel regarding its properties that requires it to be blended with petrol based diesel and/or additives to improve the fuel characteristics. This study analyses thermal cracking as an alternative technology to improve biodiesel characteristics in which, FAME based biodiesel produced by transesterification of castor oil is fed into a continuous thermal cracking reactor at temperatures range of 450-500°C and flowrate range of 20-40 g/hr. Experiments designed by response surface methodology and subsequent statistical studies show that temperature and feed flowrate significantly affect the products yield. Response surfaces were used to study the impact of temperature and flowrate on the product properties. After each experiment, the produced crude bio-oil was distilled and diesel cut was separated. As shorter chain molecules are produced through thermal cracking, the distillation curve of the diesel cut fitted more with petrol based diesel curve in comparison to the biodiesel. Moreover, the produced diesel cut properties adequately pose within property ranges defined by the related standard of petrol based diesel. Cold flow properties, high heating value as the main drawbacks of the biodiesel are improved by this technology. Thermal cracking decreases kinematic viscosity, Flash point and cetane number.
Abstract: This study was conducted to determine that carrot powder obtain by different drying methods (oven and vacuum-freeze dryer) of carrot unfit for human consumption that whether feed additives in animal nutrition or not. Carrots randomly divided 2 groups. First group was dried by using oven, second group was by using vacuum freeze dryer methods. Dried carrot prepared from fresh carrot was analysed nutrient matter (energy, crude protein, crude oil, crude ash, beta carotene, mineral concentration and colour). The differences between groups in terms of energy, crude protein, ash, Ca and Mg was not significant (P>0,05). Crude oil, P, beta carotene content and colour values (L, a, b) with vacuum-freeze dryer group was greater than oven group (P
Abstract: Advance in techniques of image and video processing has enabled the development of intelligent video surveillance systems. This study was aimed to automatically detect moving human objects and to analyze events of dual human interaction in a surveillance scene. Our system was developed in four major steps: image preprocessing, human object detection, human object tracking, and motion trajectory analysis. The adaptive background subtraction and image processing techniques were used to detect and track moving human objects. To solve the occlusion problem during the interaction, the Kalman filter was used to retain a complete trajectory for each human object. Finally, the motion trajectory analysis was developed to distinguish between the interaction and non-interaction events based on derivatives of trajectories related to the speed of the moving objects. Using a database of 60 video sequences, our system could achieve the classification accuracy of 80% in interaction events and 95% in non-interaction events, respectively. In summary, we have explored the idea to investigate a system for the automatic classification of events for interaction and non-interaction events using surveillance cameras. Ultimately, this system could be incorporated in an intelligent surveillance system for the detection and/or classification of abnormal or criminal events (e.g., theft, snatch, fighting, etc.).
Abstract: This paper presented a study of three algorithms, the
equalization algorithm to equalize the transmission channel with ZF
and MMSE criteria, application of channel Bran A, and adaptive
filtering algorithms LMS and RLS to estimate the parameters of the
equalizer filter, i.e. move to the channel estimation and therefore
reflect the temporal variations of the channel, and reduce the error in
the transmitted signal. So far the performance of the algorithm
equalizer with ZF and MMSE criteria both in the case without noise,
a comparison of performance of the LMS and RLS algorithm.
Abstract: Distributed applications deployed on LEO satellites
and ground stations require substantial communication between
different members in a constellation to overcome the earth
coverage barriers imposed by GEOs. Applications running on LEO
constellations suffer the earth line-of-sight blockage effect. They
need adequate lab testing before launching to space. We propose
a scalable cloud-based network simulation framework to simulate
problems created by the earth line-of-sight blockage. The framework
utilized cloud IaaS virtual machines to simulate LEO satellites
and ground stations distributed software. A factorial ANOVA
statistical analysis is conducted to measure simulator overhead on
overall communication performance. The results showed a very low
simulator communication overhead. Consequently, the simulation
framework is proposed as a candidate for testing LEO constellations
with distributed software in the lab before space launch.
Abstract: Complex lifting entry was selected for precise landing
performance during the Mars Science Laboratory entry. This study
aims to develop the three-dimensional numerical method for precise
computation and the surface panel method for rapid engineering
prediction. Detailed flow field analysis for Mars exploration mission
was performed by carrying on a series of fully three-dimensional
Navier-Stokes computations. The static aerodynamic performance was
then discussed, including the surface pressure, lift and drag coefficient,
lift-to-drag ratio with the numerical and engineering method.
Computation results shown that the shock layer is thin because of
lower effective specific heat ratio, and that calculated results from both
methods agree well with each other, and is consistent with the
reference data. Aerodynamic performance analysis shows that CG
location determines trim characteristics and pitch stability, and certain
radially and axially shift of the CG location can alter the capsule lifting
entry performance, which is of vital significance for the aerodynamic
configuration design and inner instrument layout of the Mars entry
capsule.
Abstract: In this paper we propose a computer-aided solution
with Genetic Algorithms in order to reduce the drafting of reports:
FMEA analysis and Control Plan required in the manufacture of the
product launch and improved knowledge development teams for
future projects. The solution allows to the design team to introduce
data entry required to FMEA. The actual analysis is performed using
Genetic Algorithms to find optimum between RPN risk factor and
cost of production. A feature of Genetic Algorithms is that they are
used as a means of finding solutions for multi criteria optimization
problems. In our case, along with three specific FMEA risk factors is
considered and reduce production cost. Analysis tool will generate
final reports for all FMEA processes. The data obtained in FMEA
reports are automatically integrated with other entered parameters in
Control Plan. Implementation of the solution is in the form of an
application running in an intranet on two servers: one containing
analysis and plan generation engine and the other containing the
database where the initial parameters and results are stored. The
results can then be used as starting solutions in the synthesis of other
projects. The solution was applied to welding processes, laser cutting
and bending to manufacture chassis for buses. Advantages of the
solution are efficient elaboration of documents in the current project
by automatically generating reports FMEA and Control Plan using
multiple criteria optimization of production and build a solid
knowledge base for future projects. The solution which we propose is
a cheap alternative to other solutions on the market using Open
Source tools in implementation.
Abstract: More than 3000 plants of notable phyto-therapeutic
value grow in South Africa; these include Cissampelos capensis,
commonly known in Afrikaans as dawidjie or dawidjiewortel. C.
capensis is the most significant and popular medicinal plant used by
the Khoisan as well as other rural groups in the Western region of
South Africa. Its rhizomes are traditionally used to treat male fertility
problems. Yet, no studies have investigated the effects of this plant or
its extracts on human spermatozoa. Therefore, this study aimed at
investigating the effects of C. capensis rhizome extract (CRE)
fractions on ejaculated human spermatozoa in vitro. Spermatozoa
from a total of 77 semen samples were washed with human tubular
fluid medium supplemented with bovine serum albumin (HTF-BSA)
and incubated for 2 hours with 20 μg/ml progesterone (P4) followed
by incubation with different concentrations (0, 0.05, 0.5, 5, 50, 200
μg/ml) of fractionated CRE (F1=0% MeOH, F2=30% MeOH,
F3=60% MeOH and F4=100% MeOH) for 1.5 hours at 37°C. A
sample without addition of CRE fractions served as control. Samples
were analyzed for sperm motility, reactive oxygen species (ROS),
DNA-fragmentation, acrosome reaction and capacitation. Results
showed that F1 resulted in significantly higher values for ROS,
capacitation and hyper-activation compared to F2, F3, and F4 with
P4-stimulated samples generally having higher values. No significant
effect was found for the other parameters. In conclusion, alkaloids
present in F1 of CRE appear to have triggered sperm intrinsic ROS
production leading to sperm capacitation and acrosome reaction
induced by P4.
Abstract: Current research is targeting new molecular
mechanisms that underlie non-alcoholic fatty liver disease (NAFLD)
and associated metabolic disorders like non-alcoholic steatohepatitis
(NASH). Forty New Zealand White rabbits have been used and fed a
high protein (HP) and energy diet based on grains and containing
11.76 MJ/kg. Boron added to 3 experimental groups’ drinking waters
(30 mg boron/L) as boron compounds. Biochemical analysis
including boron levels, and nuclear magnetic resonance (NMR) based
metabolomics evaluation, and mRNA expression of peroxisome
proliferator-activated receptor (PPAR) family was performed. LDLcholesterol
concentrations alone were decreased in all the
experimental groups. Boron levels in serum and feces were increased.
Content of acetate was in about 2x higher for anhydrous borax group,
at least 3x higher for boric acid group. PPARα mRNA expression
was significantly decreased in boric acid group. Anhydrous borax
attenuated mRNA levels of PPARγ, which was further suppressed by
boric acid. Boron supplementation decreased the degenerative
alterations in hepatocytes. Except borax group other boron groups did
not have a pronounced change in tubular epithels of kidney. In
conclusion, high protein and energy diet leads hepatocytes’
degenerative changes which can be prevented by boron
supplementation. Boric acid seems to be more effective in this
situation.
Abstract: Image segmentation and edge detection is a fundamental section in image processing. In case of noisy images Edge Detection is very less effective if we use conventional Spatial Filters like Sobel, Prewitt, LOG, Laplacian etc. To overcome this problem we have proposed the use of Stochastic Gradient Mask instead of Spatial Filters for generating gradient images. The present study has shown that the resultant images obtained by applying Stochastic Gradient Masks appear to be much clearer and sharper as per Edge detection is considered.
Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: The substantial development of the construction
industry has forced the cement industry, its major support, to focus
on achieving maximum productivity to meet the growing demand for
this material. This means that the reliability of a cement production
system needs to be at the highest level that can be achieved by good
maintenance. This paper studies the extent to which the
implementation of RCM is needed as a strategy for increasing the
reliability of the production systems component can be increased,
thus ensuring continuous productivity. In a case study of four Libyan
cement factories, 80 employees were surveyed and 12 top and middle
managers interviewed. It is evident that these factories usually
breakdown more often than once per month which has led to a
decline in productivity. In many times they cannot achieve the
minimum level of production amount. This has resulted from the
poor reliability of their production systems as a result of poor or
insufficient maintenance. It has been found that most of the factories’
employees misunderstand maintenance and its importance. The main
cause of this problem is the lack of qualified and trained staff, but in
addition it has been found that most employees are not found to be
motivated as a result of a lack of management support and interest. In
response to these findings, it has been suggested that the RCM
strategy should be implemented in the four factories. The results
show the importance of the development of maintenance strategies
through the implementation of RCM in these factories. The purpose
of it would be to overcome the problems that could secure the
reliability of the production systems. This study could be a useful
source of information for academic researchers and the industrial
organizations which are still experiencing problems in maintenance
practices.
Abstract: Computational fluid dynamics analysis of the burning
of syngas fuels derived from biomass and plastic solid waste mixture
through gasification process is presented in this paper. The syngas
fuel is burned in gas turbine can combustor. Gas turbine can
combustor with swirl is designed to burn the fuel efficiently and
reduce the emissions. The main objective is to test the impact of the
alternative syngas fuel compositions and lower heating value on the
combustion performance and emissions. The syngas fuel is produced
by blending palm kernel shell (PKS) with polyethylene (PE) waste
via catalytic steam gasification (fluidized bed reactor). High
hydrogen content syngas fuel was obtained by mixing 30% PE waste
with PKS. The syngas composition obtained through the gasification
process is 76.2% H2, 8.53% CO, 4.39% CO2 and 10.90% CH4. The
lower heating value of the syngas fuel is LHV = 15.98 MJ/m3. Three
fuels were tested in this study natural gas (100%CH4), syngas fuel
and pure hydrogen (100% H2). The power from the combustor was
kept constant for all the fuels tested in this study. The effect of syngas
fuel composition and lower heating value on the flame shape, gas
temperature, mass of carbon dioxide (CO2) and nitrogen oxides
(NOX) per unit of energy generation is presented in this paper. The
results show an increase of the peak flame temperature and NO mass
fractions for the syngas and hydrogen fuels compared to natural gas
fuel combustion. Lower average CO2 emissions at the exit of the
combustor are obtained for the syngas compared to the natural gas
fuel.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: In this study, one of the tools of Islamic financing
known as “Sukuk” a non-interest bearing investment which has
started to be implemented in Turkey and the world as a whole is
discussed. In order to increase the vitality and efficiency of the
economy, by taking lessons from the recent economic crisis new
developments in the banking and investment sector are being
expanded. The purpose of all investors is to obtain more revenue
through the use of capital. The inability of traditional investment
tools to meet the expectations of investors and the interest based
financial system where one investor benefits at the expense of
another there has been the need for a different, reliable and noninterest
bearing financial market that is consistent with the Islamic
rule. As a result an alternative and more reliable interest free
financing tool “Sukuk” rental certificates covering people who are
sensitive to Islamic rules, appeal to all segments, hidden remaining
capital that contributes to the economy, reduce disparities in income
distribution, common risk sharing system of profit and loss sharing
has emerged. Today, for the structural countries by examining the
state of the world market economy the applicability, enactment and
future issues associated with this attractive kind of Islamic finance
namely the “Sukuk” market has been explained.
Abstract: This paper addresses the design of hospital Intensive
Care Unit windows for the achievement of visual comfort and energy
savings. The aim was to identify the window size and shading system
configurations that could fulfill daylighting adequacy, avoid glare
and reduce energy consumption. The study focused on addressing the
effect of utilizing different shading systems in association with a
range of Window-to-Wall Ratios (WWR) in different orientations
under the desert clear-sky of Cairo, Egypt.
The results of this study demonstrated that solar penetration is a
critical concern affecting the design of ICU windows in desert
locations, as in Cairo, Egypt. Use of shading systems was found to be
essential in providing acceptable daylight performance and energy
saving. Careful positioning of the ICU window towards a proper
orientation can dramatically improve performance. It was observed
that ICU windows facing the north direction enjoyed the widest range
of successful window configuration possibilities at different WWRs.
ICU windows facing south enjoyed a reasonable number of
configuration options as well. By contrast, the ICU windows facing
the east orientation had a very limited number of options that provide
acceptable performance. These require additional local shading
measures at certain times due to glare incidence. Moreover, use of
horizontal sun breakers and solar screens to protect the ICU windows
proved to be more successful than the other alternatives in a wide
range of Window to Wall Ratios. By contrast, the use of light shelves
and vertical shading devices seemed questionable.
Abstract: Microstructural and electrical properties of
Cu-chromium alloy (Cu-Cr) dispersed with vapor-grown carbon fiber
(VGCF) prepared by powder metallurgy (P/M) process have been
investigated. Cu-0.7 mass% Cr pre-alloyed powder (Cu-Cr) made by
water atomization process was used as raw materials, which contained
solid solute Cr elements in Cu matrix. The alloy powder coated with
un-bundled VGCF by using oil coating process was consolidated at
1223 K in vacuum by spark plasma sintering, and then extruded at
1073 K. The extruded Cu-Cr alloy (monolithic alloy) had 209.3 MPa
YS and 80.4 IACS% conductivity. The extruded Cu-Cr with 0.1
mass% VGCF composites revealed a small decrease of YS compared
to the monolithic Cu-Cr alloy. On the other hand, the composite had a
higher electrical conductivity than that of the monolithic alloy. For
example, Cu-Cr with 0.1 mass% VGCF composite sintered for 5 h
showed 182.7 MPa YS and 89.7 IACS% conductivity. In the case of
Cu-Cr with VGCFs composites, the Cr concentration was observed
around VGCF by SEM-EDS analysis, where Cr23C6 compounds were
detected by TEM observation. The amount of Cr solid solution in the
matrix of the Cu-Cr composites alloy was about 50% compared to the
monolithic Cu-Cr sintered alloy, and resulted in the remarkable
increment of the electrical conductivity.
Abstract: To ensure student success in a non-majors biology course, a flipped classroom pedagogical approach was developed and implemented. All students were assigned online lectures to listen to before they come to class. A three hour lecture was split into one hour of online component, one hour of in class lecture and one hour of worksheets done by students in the classroom. This deviation from a traditional 3 hour in class lecture has resulted in increased student interest in science as well as better understanding of difficult scientific concepts. A pre and post survey was given to measure the interest in the subject and grades were used to measure the success rates. While the overall grade average did not change dramatically, students reported a much better appreciation of biology. Also, students overwhelmingly like the use of worksheets in class to help them understand the concepts. They liked the fact that they could listen to lectures at their own pace on line and even repeat if needed. The flipped classroom approach turned out to work really well our non-science majors and the author is ready to implement this in other classrooms.