Abstract: Three batches of yogurts were made with soy protein
isolate (SPI) supplemented with 2% (S2), 4% (S4) or 6% (S6) of
skim milk powder (SMP). The fourth batch (control; S0) was
prepared from SPI without SMP supplementation. Lactobacillus
delbrueckii ssp. bulgaricus ATCC 11842 (Lb 11842) and
Streptococcus thermophilus ST 1342 (ST 1342) were used as the
starter culture. Biotransformation of the inactive forms, isoflavone
glycosides (IG) to biologically active forms, isoflavone aglycones
(IA), was determined during 28 d storage. The viability of both
microorganisms was significantly higher (P < 0.05) in S2, S4, and S6
than that in S0. The ratio of lactic acid/acetic acid in S0 was in the
range of 15.53 – 22.31 compared to 7.24 – 12.81 in S2, S4 and S6.
The biotransformation of IG to IA in S2, S4 and S6 was also
enhanced by 9.9 -13.3% compared to S0.
Abstract: In an electric power system, spinning reserve
requirements can be determined by using deterministic and/or
probabilistic measures. Although deterministic methods are usual in
many systems, application of probabilistic methods becomes
increasingly important in the new environment of the electric power
utility industry. This is because of the increased uncertainty
associated with competition. In this paper 1) a new probabilistic
method is presented which considers the reliability of transmission
system in a simplified manner and 2) deterministic and probabilistic
methods are compared. The studied methods are applied to the Roy
Billinton Test System (RBTS).
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Hospitals in southern Hualien teamed with the
Hypertension Joint Care Network. Working with the network, the
team provided a special designed health education to the individual
who had been identified as a hypertension patient in the outpatient
department. Some metabolism improvements achieved. This is a
retrospective study by purposively taking 106 patients from a hospital
between 2008 and 2010. Records of before and after education
intervention of the objects was collected and analyzed to see the how
the intervention affected the patients- hypertension control via clinical
parameter monitoring. The results showed that the clinical indicators,
the LDL-C, the cholesterol and the systolic blood pressure were
significantly improved. The study provides evidence for the
effectiveness of the network in controlling hypertension.
Abstract: In this paper, perceptions of actors on changes in
crop productivity, quantity and quality of water, and determinants of
their perception are analyzed using descriptive statistics and ordered
logit model. Data collected from 297 Ethiopian farmers and 103
agricultural professionals from December 2009 to January 2010 are
employed. Results show that the majority of the farmers and
professionals recognized decline in water resources, reasoning
climate changes and soil erosion as some of the causes. However,
there is a variation in views on changes in productivity. The
household asset, education level, age and geographical positions are
found to affect farmers- perception on changes in crop productivity.
But, the study underlines that there is no evidence that farmers-
economic status, age, or education level affects recognition of
degradation of water resources. Thus, more focus shall be given on
providing them different coping mechanisms and alternative
resource conserving technologies than educating about the
problems.
Abstract: The current situation in the eurozone raises a number of topics for discussion and to help in finding an answer to the question of whether a common currency is a more suitable means of coping with the impact of the financial crisis or whether national currencies are better suited to this. The economic situation in the EU is now considerably volatile and, due to problems with the fulfilment of the Maastricht convergence criteria, it is now being considered whether, in their further development, new member states will decide to distance themselves from the euro or will, in an attempt to overcome the crisis, speed up the adoption of the euro. The Czech Republic is one country with little interest in adopting the euro, justified by the fact that a better alternative to dealing with this crisis is an independent monetary policy and its ability to respond flexibly to the economic situation not only in Europe, but around the world. One attribute of the crisis in the Czech Republic and its mitigation is the freely floating exchange rate of the national currency. It is not only the Czech Republic that is attempting to alleviate the impact of the crisis, but also new EU member countries facing fresh questions to which theory have yet to provide wholly satisfactory answers. These questions undoubtedly include the problem of inflation targeting and the choice of appropriate instruments for achieving financial stability. The difficulty lies in the fact that these objectives may be contradictory and may require more than one means of achieving them. In this respect we may assume that membership of the euro zone might not in itself mitigate the development of the recession or protect the nation from future crises. We are of the opinion that the decisive factor in the development of any economy will continue to be the domestic economic policy and the operability of market economic mechanisms. We attempt to document this fact using selected countries as examples, these being the Czech Republic, Poland, Hungary, and Slovakia.
Abstract: In the modern manufacturing systems, the use of
thermal cutting techniques using oxyfuel, plasma and laser have
become indispensable for the shape forming of high quality complex
components; however, the conventional chip removal production
techniques still have its widespread space in the manufacturing
industry. Both these types of machining operations require the
positioning of end effector tool at the edge where the cutting process
commences. This repositioning of the cutting tool in every machining
operation is repeated several times and is termed as non-productive
time or airtime motion. Minimization of this non-productive
machining time plays an important role in mass production with high
speed machining. As, the tool moves from one region to the other by
rapid movement and visits a meticulous region once in the whole
operation, hence the non-productive time can be minimized by
synchronizing the tool movements. In this work, this problem is
being formulated as a general travelling salesman problem (TSP) and
a genetic algorithm approach has been applied to solve the same. For
improving the efficiency of the algorithm, the GA has been
hybridized with a noble special heuristic and simulating annealing
(SA). In the present work a novel heuristic in the combination of GA
has been developed for synchronization of toolpath movements
during repositioning of the tool. A comparative analysis of new Meta
heuristic techniques with simple genetic algorithm has been
performed. The proposed metaheuristic approach shows better
performance than simple genetic algorithm for minimization of nonproductive
toolpath length. Also, the results obtained with the help of
hybrid simulated annealing genetic algorithm (HSAGA) are also
found better than the results using simple genetic algorithm only.
Abstract: Multidrug resistant organisms have been taunting the
medical world for the last few decades. Even with new antibiotics
developed, resistant strains have emerged soon after. With the
advancement of nanotechnology, we investigated colloidal silver
nanoparticles for its antimicrobial activity against Pseudomonas
aeruginosa. This organism is a multidrug resistant which contributes
to the high morbidity and mortality in immunocompromised patients.
Five multidrug resistant strains were used in this study. The
antimicrobial effect was studied using the disc diffusion and broth
dilution techniques. An inhibition zone of 11 mm was observed with
10 μg dose of the nanoparticles. The nanoparticles exhibited MIC of
50 μg/ml when added at the lag phase and the subinhibitory
concentration was measured as 100 μg/ml. The MIC50 value showed
to be 15 μg/ml. This study suggests that silver nanoparticles can be
further developed as an antimicrobial agent, hence decreasing the
burden of the multidrug resistance phenomena.
Abstract: This paper is to present context-aware sensor grid
framework for agriculture and its design challenges. Use of sensor
networks in the domain of agriculture is not new. However, due to
the unavailability of any common framework, solutions that are
developed in this domain are location, environment and problem
dependent. Keeping the need of common framework for agriculture,
Context-Aware Sensor Grid Framework is proposed. It will be
helpful in developing solutions for majority of the problems related
to irrigation, pesticides spray, use of fertilizers, regular monitoring of
plot and yield etc. due to the capability of adjusting according to
location and environment. The proposed framework is composed of
three layer architecture including context-aware application layer,
grid middleware layer and sensor network layer.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: In this paper, we present a novel objective nonreference
performance assessment algorithm for image fusion. It takes
into account local measurements to estimate how well the important
information in the source images is represented by the fused image.
The metric is based on the Universal Image Quality Index and uses
the similarity between blocks of pixels in the input images and the
fused image as the weighting factors for the metrics. Experimental
results confirm that the values of the proposed metrics correlate well
with the subjective quality of the fused images, giving a significant
improvement over standard measures based on mean squared error
and mutual information.
Abstract: Sensors possess several properties of physical
measures. Whether devices that convert a sensed signal into an
electrical signal, chemical sensors and biosensors, thus all these
sensors can be considered as an interface between the physical and
electrical equipment. The problem is the analysis of the multitudes of
saved settings as input variables. However, they do not all have the
same level of influence on the outputs. In order to identify the most
sensitive parameters, those that can guide users in gathering
information on the ground and in the process of model calibration
and sensitivity analysis for the effect of each change made.
Mathematical models used for processing become very complex.
In this paper a fuzzy rule-based system is proposed as a solution
for this problem. The system collects the available signals
information from sensors. Moreover, the system allows the study of
the influence of the various factors that take part in the decision
system. Since its inception fuzzy set theory has been regarded as a
formalism suitable to deal with the imprecision intrinsic to many
problems. At the same time, fuzzy sets allow to use symbolic models.
In this study an example was applied for resolving variety of
physiological parameters that define human health state. The
application system was done for medical diagnosis help. The inputs
are the signals expressed the cardiovascular system parameters, blood
pressure, Respiratory system paramsystem was done, it will be able
to predict the state of patient according any input values.
Abstract: It is shown that the relationship of tick-borne
encephalitis virus with the human body comes in two ways, the
development of acute infection with the outcome in convalescence
and long stay by the virus in the body, its persistence in the nervous
tissue with periodic reactivation and prolonged circulating
immunoglobulin M. In spite of the fact that tick-borne encephalitis
virus has a tropism for nerve tissue, involvement in the process of
blood cells is an integral component of the infection. Comprehensive
study of the relation of factors of innate and adaptive immunity in the
tick-borne encephalitis providing insight into the features of chronic
disease.
Abstract: The blood ducts must be occluded to avoid loss of
blood from vessels in laparoscopic surgeries. This paper presents a
locking mechanism to be used in a ligation laparoscopic procedure
(LigLAP I), as an alternative solution for a stapling procedure.
Currently, stapling devices are being used to occlude vessels. Using
these devices may result in some problems, including injury of bile
duct, taking up a great deal of space behind the vessel, and bile leak.
In this new procedure, a two-layer suture occludes a vessel. A
locking mechanism is also required to hold the suture. Since there is
a limited space at the device tip, a Shape Memory Alloy (SMA)
actuator is used in this mechanism. Suitability for cleanroom
applications, small size, and silent performance are among the
advantages of SMA actuators in biomedical applications. An
experimental study is conducted to examine the function of the
locking mechanism. To set up the experiment, a prototype of a
locking mechanism is built using nitinol, which is a nickel-titanium
shape memory alloy. The locking mechanism successfully locks a
polymer suture for all runs of the experiment. In addition, the effects
of various surface materials on the applied pulling forces are studied.
Various materials are mounted at the mechanism tip to compare the
maximum pulling forces applied to the suture for each material. The
results show that the various surface materials on the device tip
provide large differences in the applied pulling forces.
Abstract: Silicon is a beneficial element for plant growth. It
helps plants to overcome multiple stresses, alleviates metal toxicity
and improves nutrient imbalance. Field experiment was conducted as
split-split plot arranged in a randomized complete block design with
four replications. Irrigation system include continues flooding and
deficit as main plots and nitrogen rates N0, N46, N92, and N138 kg/ha
as sub plots and silicon rates Si0 & Si500 kg/ha as sub-subplots.
Results indicate that grain yield had not significant difference
between irrigation systems. Flooding irrigation had higher biological
yield than deficit irrigation whereas, no significant difference in grain
and straw yield. Nitrogen application increased grain, biological and
straw yield. Silicon application increased grain, biological and straw
yield but, decreased harvest index. Flooding irrigation had higher
number of total tillers / hill than deficit irrigation, but deficit
irrigation had higher number of fertile tillers / hill than flooding
irrigation. Silicon increased number of filled spikelet and decreased
blank spikelet. With high nitrogen application decreased 1000-grain
weight. It can be concluded that if the nitrogen application was high
and water supplied was available we could have silicon application
until increase grain yield.
Abstract: International literature emphasizes on the concern regarding the phenomenon of aggression in hospital. This paper focuses on the reality of aggressive interactions reigning within an emergency triage involving three chaps of protagonists: the professionals, the patients and their carers. The data collection was made from a grid of observation, in which the various variables exposed in the literature were integrated. They observations took place around the clock, for three weeks, at the rate of one week a month. In this research 331 aggressive interactions have been listed and analyzed by means of the software SPSS. This research is one of the very few continuous observation surveys in the literature. It shows the various human factors at play in the emergence of aggressive interaction. The data may be used both for taking steps in primary prevention, thanks to the analysis of interaction modes, and in secondary prevention by integrating the useful results in situational prevention.
Abstract: This article presents a detailed analysis and comparative
performance evaluation of model reference adaptive control systems.
In contrast to classical control theory, adaptive control methods allow
to deal with time-variant processes. Inspired by the works [1] and
[2], two methods based on the MIT rule and Lyapunov rule are
applied to a linear first order system. The system is simulated and
it is investigated how changes to the adaptation gain affect the
system performance. Furthermore, variations in the reference model
parameters, that is changing the desired closed-loop behaviour are
examinded.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: In this paper, the typical exponential method, diamond difference and modified time discrete scheme is researched for self adaptive time step. The second-order time evolution scheme is applied to time-dependent spherical neutron transport equation by discrete ordinates method. The numerical results show that second-order time evolution scheme associated exponential method has some good properties. The time differential curve about neutron current is more smooth than that of exponential method and diamond difference and modified time discrete scheme.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.